Merge branch 'stmmac-add-support-for-stm32mp1'

Christophe Roullier says:

====================
net: ethernet: stmmac: add support for stm32mp1

Patches to have Ethernet support on stm32mp1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/arm/stm32/stm32-syscon.txt

+STMicroelectronics STM32 Platforms System Controller
+
+Properties:
+   - compatible : should contain two values. First value must be :
+                 - " st,stm32mp157-syscfg " - for stm32mp157 based SoCs,
+                 second value must be always "syscon".
+   - reg : offset and length of the register set.
+
+ Example:
+         syscfg: syscon@50020000 {
+                 compatible = "st,stm32mp157-syscfg", "syscon";
+                 reg = <0x50020000 0x400>;
+         };
+

Documentation/devicetree/bindings/net/stm32-dwmac.txt

@@ -6,14 +6,28 @@ Please see stmmac.txt for the other unchanged properties.
 The device node has following properties.
 
 Required properties:
-- compatible:  Should be "st,stm32-dwmac" to select glue, and
+- compatible:  For MCU family should be "st,stm32-dwmac" to select glue, and
 	       "snps,dwmac-3.50a" to select IP version.
+	       For MPU family should be "st,stm32mp1-dwmac" to select
+	       glue, and "snps,dwmac-4.20a" to select IP version.
 - clocks: Must contain a phandle for each entry in clock-names.
 - clock-names: Should be "stmmaceth" for the host clock.
 	       Should be "mac-clk-tx" for the MAC TX clock.
 	       Should be "mac-clk-rx" for the MAC RX clock.
+	       For MPU family need to add also "ethstp" for power mode clock and,
+	                                       "syscfg-clk" for SYSCFG clock.
+- interrupt-names: Should contain a list of interrupt names corresponding to
+           the interrupts in the interrupts property, if available.
+		   Should be "macirq" for the main MAC IRQ
+		   Should be "eth_wake_irq" for the IT which wake up system
 - st,syscon : Should be phandle/offset pair. The phandle to the syscon node which
 	       encompases the glue register, and the offset of the control register.
+
+Optional properties:
+- clock-names:     For MPU family "mac-clk-ck" for PHY without quartz
+- st,int-phyclk (boolean) :  valid only where PHY do not have quartz and need to be clock
+	           by RCC
+
 Example:
 
 	ethernet@40028000 {

drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c

@@ -472,7 +472,8 @@ stmmac_probe_config_dt(struct platform_device *pdev, const char **mac)
 	}
 
 	if (of_device_is_compatible(np, "snps,dwmac-4.00") ||
-	    of_device_is_compatible(np, "snps,dwmac-4.10a")) {
+	    of_device_is_compatible(np, "snps,dwmac-4.10a") ||
+	    of_device_is_compatible(np, "snps,dwmac-4.20a")) {
 		plat->has_gmac4 = 1;
 		plat->has_gmac = 0;
 		plat->pmt = 1;