Merge tag 'imx-dt-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt

The i.MX device tree updates for 4.5:
- New boards support: imx51-ts4800, imx6q-novena, CompuLab imx7d SoM/SBC,
  vf610m4-cosmic
- Add ADC device support for imx6ul and imx7d
- Remove config space from PCIe controller ranges property for i.MX6
- Add Vivante GPU nodes for i.MX6
- Add DCU, LCD, and SATA devices for LS1021A
- A series to update Ventana gw5xxx boards getting HDMI and LVDS to work
  simultaneously and devices like PWM and SPI added
- Quite a few random cleanups and minor updates

* tag 'imx-dt-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (50 commits)
  ARM: dts: imx7d: sbc-imx7: add basic board support
  ARM: dts: imx7d: cl-som-imx7: add basic module support
  ARM: dts: TS-4800: add touchscreen support
  ARM: dts: ts-4800: Add LCD support
  ARM: dts: imx6q: add Novena board
  devicetree: bindings: Add vendor prefix for Kosagi
  ARM: dts: TS-4800: use weim IP to map the FPGA
  ARM: dts: TS-4800: drop uart rts/cts pin reservations
  ARM: dts: imx6: add Vivante GPU nodes
  ARM: dts: imx28: add alternate auart4 pinmux
  ARM: dts: ls1021a: add sata node to dts
  ARM: dts: TS-4800: add basic device tree
  of: documentation: add bindings documentation for TS-4800
  of: add vendor prefix for Technologic Systems
  ARM: dts: imx7d-sdb: add ADC support
  ARM: dts: imx7d.dtsi: add ADC support
  ARM: dts: vf-colibri: add CAN support
  ARM: mxs: dt: cfa10057: fix backlight PWM
  ARM: dts: imx6qdl: move GIC to right location in DT
  ARM: dts: imx6qdl: add IPU aliases
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/arm/technologic.txt

+Technologic Systems Platforms Device Tree Bindings
+--------------------------------------------------
+
+TS-4800 board
+Required root node properties:
+	- compatible = "technologic,imx51-ts4800", "fsl,imx51";

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -123,6 +123,7 @@ jedec	JEDEC Solid State Technology Association
 karo	Ka-Ro electronics GmbH
 keymile	Keymile GmbH
 kinetic Kinetic Technologies
+kosagi	Sutajio Ko-Usagi PTE Ltd.
 lacie	LaCie
 lantiq	Lantiq Semiconductor
 lenovo	Lenovo Group Ltd.
@@ -224,6 +225,7 @@ stericsson	ST-Ericsson
 synology	Synology, Inc.
 tbs	TBS Technologies
 tcl	Toby Churchill Ltd.
+technologic	Technologic Systems
 thine	THine Electronics, Inc.
 ti	Texas Instruments
 tlm	Trusted Logic Mobility

arch/arm/boot/dts/Makefile

@@ -274,7 +274,8 @@ dtb-$(CONFIG_SOC_IMX51) += \
 	imx51-apf51dev.dtb \
 	imx51-babbage.dtb \
 	imx51-digi-connectcore-jsk.dtb \
-	imx51-eukrea-mbimxsd51-baseboard.dtb
+	imx51-eukrea-mbimxsd51-baseboard.dtb \
+	imx51-ts4800.dtb
 dtb-$(CONFIG_SOC_IMX53) += \
 	imx53-ard.dtb \
 	imx53-m53evk.dtb \
@@ -331,6 +332,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-hummingboard.dtb \
 	imx6q-nitrogen6x.dtb \
 	imx6q-nitrogen6_max.dtb \
+	imx6q-novena.dtb \
 	imx6q-phytec-pbab01.dtb \
 	imx6q-rex-pro.dtb \
 	imx6q-sabreauto.dtb \
@@ -356,6 +358,8 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
 dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ul-14x14-evk.dtb
 dtb-$(CONFIG_SOC_IMX7D) += \
+	imx7d-cl-som-imx7.dtb \
+	imx7d-sbc-imx7.dtb \
 	imx7d-sdb.dtb
 dtb-$(CONFIG_SOC_LS1021A) += \
 	ls1021a-qds.dtb \
@@ -365,6 +369,7 @@ dtb-$(CONFIG_SOC_VF610) += \
 	vf610-colibri-eval-v3.dtb \
 	vf610m4-colibri.dtb \
 	vf610-cosmic.dtb \
+	vf610m4-cosmic.dtb \
 	vf610-twr.dtb
 dtb-$(CONFIG_ARCH_MXS) += \
 	imx23-evk.dtb \

arch/arm/boot/dts/imx25-pinfunc.h

@@ -284,6 +284,7 @@
 #define MX25_PAD_CONTRAST__CC4			0x118 0x310 0x000 0x11 0x000
 #define MX25_PAD_CONTRAST__PWM4_PWMO		0x118 0x310 0x000 0x14 0x000
 #define MX25_PAD_CONTRAST__FEC_CRS		0x118 0x310 0x508 0x15 0x001
+#define MX25_PAD_CONTRAST__USBH2_PWR		0x118 0x310 0x000 0x16 0x000
 
 #define MX25_PAD_PWM__PWM			0x11c 0x314 0x000 0x10 0x000
 #define MX25_PAD_PWM__GPIO_1_26			0x11c 0x314 0x000 0x15 0x000
@@ -439,6 +440,7 @@
 #define MX25_PAD_SD1_DATA3__GPIO_2_28		0x1a4 0x39c 0x000 0x15 0x000
 
 #define MX25_PAD_KPP_ROW0__KPP_ROW0		0x1a8 0x3a0 0x000 0x10 0x000
+#define MX25_PAD_KPP_ROW0__UART1_DTR		0x1a8 0x3a0 0x000 0x14 0x000
 #define MX25_PAD_KPP_ROW0__GPIO_2_29		0x1a8 0x3a0 0x000 0x15 0x000
 
 #define MX25_PAD_KPP_ROW1__KPP_ROW1		0x1ac 0x3a4 0x000 0x10 0x000
@@ -446,6 +448,7 @@
 
 #define MX25_PAD_KPP_ROW2__KPP_ROW2		0x1b0 0x3a8 0x000 0x10 0x000
 #define MX25_PAD_KPP_ROW2__CSI_D0		0x1b0 0x3a8 0x488 0x13 0x002
+#define MX25_PAD_KPP_ROW2__UART1_DCD		0x1b0 0x3a8 0x000 0x14 0x000
 #define MX25_PAD_KPP_ROW2__GPIO_2_31		0x1b0 0x3a8 0x000 0x15 0x000
 
 #define MX25_PAD_KPP_ROW3__KPP_ROW3		0x1b4 0x3ac 0x000 0x10 0x000

arch/arm/boot/dts/imx25.dtsi

@@ -24,6 +24,10 @@ aliases {
 		i2c2 = &i2c3;
 		mmc0 = &esdhc1;
 		mmc1 = &esdhc2;
+		pwm0 = &pwm1;
+		pwm1 = &pwm2;
+		pwm2 = &pwm3;
+		pwm3 = &pwm4;
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;

arch/arm/boot/dts/imx28-cfa10057.dts

@@ -115,7 +115,7 @@ lradc@80050000 {
 
 			pwm: pwm@80064000 {
 				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_b>;
+				pinctrl-0 = <&pwm4_pins_a>;
 				status = "okay";
 			};
 
@@ -170,7 +170,7 @@ mac0: ethernet@800f0000 {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm 3 5000000>;
+		pwms = <&pwm 4 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 	};

arch/arm/boot/dts/imx28.dtsi

@@ -405,6 +405,17 @@ MX28_PAD_SSP3_MOSI__AUART4_RX
 					fsl,pull-up = <MXS_PULL_DISABLE>;
 				};
 
+				auart4_2pins_b: auart4@1 {
+					reg = <1>;
+					fsl,pinmux-ids = <
+						MX28_PAD_AUART0_CTS__AUART4_RX
+						MX28_PAD_AUART0_RTS__AUART4_TX
+					>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
+				};
+
 				mac0_pins_a: mac0@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <

arch/arm/boot/dts/imx51-ts4800.dts

+/*
+ * Copyright 2015 Savoir-faire Linux
+ *
+ * This device tree is based on imx51-babbage.dts
+ *
+ * Licensed under the X11 license or the GPL v2 (or later)
+ */
+
+/dts-v1/;
+#include "imx51.dtsi"
+
+/ {
+	model = "Technologic Systems TS-4800";
+	compatible = "technologic,imx51-ts4800", "fsl,imx51";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory {
+		reg = <0x90000000 0x10000000>;
+	};
+
+	clocks {
+		ckih1 {
+			clock-frequency = <22579200>;
+		};
+
+		ckih2 {
+			clock-frequency = <24576000>;
+		};
+	};
+
+	backlight_reg: regulator-backlight {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_lcd>;
+		regulator-name = "enable_lcd_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 78770>;
+		brightness-levels = <0 150 200 255>;
+		default-brightness-level = <1>;
+		power-supply = <&backlight_reg>;
+	};
+
+	display0: display@di0 {
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lcd>;
+
+		display-timings {
+			800x480p60 {
+				native-mode;
+				clock-frequency = <30066000>;
+				hactive = <800>;
+				vactive = <480>;
+				hfront-porch = <50>;
+				hback-porch = <70>;
+				hsync-len = <50>;
+				vback-porch = <0>;
+				vfront-porch = <0>;
+				vsync-len = <50>;
+			};
+		};
+
+		port@0 {
+			display0_in: endpoint {
+				remote-endpoint = <&ipu_di0_disp0>;
+			};
+		};
+	};
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "mii";
+	phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <1>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	rtc: m41t00@68 {
+		compatible = "stm,m41t00";
+		reg = <0x68>;
+	};
+};
+
+&ipu_di0_disp0 {
+	remote-endpoint = <&display0_in>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_backlight>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&weim {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_weim>;
+	status = "okay";
+
+	fpga@0 {
+		compatible = "simple-bus";
+		fsl,weim-cs-timing = <0x0061008F 0x00000002 0x1c022000
+				      0x00000000 0x1c092480 0x00000000>;
+		reg = <0 0x0000000 0x1d000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0x1d000>;
+
+		syscon: syscon@b0010000 {
+			compatible = "syscon", "simple-mfd";
+			reg = <0x10000 0x3d>;
+			reg-io-width = <2>;
+
+			wdt@e {
+				compatible = "technologic,ts4800-wdt";
+				syscon = <&syscon 0xe>;
+			};
+		};
+
+		touchscreen {
+			compatible = "technologic,ts4800-ts";
+			reg = <0x12000 0x1000>;
+			syscon = <&syscon 0x10 6>;
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX51_PAD_CSPI1_MISO__ECSPI1_MISO	0x185
+			MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI	0x185
+			MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK	0x185
+			MX51_PAD_CSPI1_SS0__GPIO4_24		0x85 /* CS0 */
+		>;
+	};
+
+	pinctrl_enable_lcd: enablelcdgrp {
+		fsl,pins = <
+			MX51_PAD_CSI2_D12__GPIO4_9		0x1c5
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX51_PAD_SD1_CMD__SD1_CMD		0x400020d5
+			MX51_PAD_SD1_CLK__SD1_CLK		0x20d5
+			MX51_PAD_SD1_DATA0__SD1_DATA0		0x20d5
+			MX51_PAD_SD1_DATA1__SD1_DATA1		0x20d5
+			MX51_PAD_SD1_DATA2__SD1_DATA2		0x20d5
+			MX51_PAD_SD1_DATA3__SD1_DATA3		0x20d5
+			MX51_PAD_GPIO1_0__GPIO1_0		0x100
+			MX51_PAD_GPIO1_1__GPIO1_1		0x100
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX51_PAD_EIM_EB2__FEC_MDIO		0x000001f5
+			MX51_PAD_EIM_EB3__FEC_RDATA1		0x00000085
+			MX51_PAD_EIM_CS2__FEC_RDATA2		0x00000085
+			MX51_PAD_EIM_CS3__FEC_RDATA3		0x00000085
+			MX51_PAD_EIM_CS4__FEC_RX_ER		0x00000180
+			MX51_PAD_EIM_CS5__FEC_CRS		0x00000180
+			MX51_PAD_DISP2_DAT10__FEC_COL		0x00000180
+			MX51_PAD_DISP2_DAT11__FEC_RX_CLK	0x00000180
+			MX51_PAD_DISP2_DAT14__FEC_RDATA0	0x00002180
+			MX51_PAD_DISP2_DAT15__FEC_TDATA0	0x00002004
+			MX51_PAD_NANDF_CS2__FEC_TX_ER		0x00002004
+			MX51_PAD_DI2_PIN2__FEC_MDC		0x00002004
+			MX51_PAD_DISP2_DAT6__FEC_TDATA1		0x00002004
+			MX51_PAD_DISP2_DAT7__FEC_TDATA2		0x00002004
+			MX51_PAD_DISP2_DAT8__FEC_TDATA3		0x00002004
+			MX51_PAD_DISP2_DAT9__FEC_TX_EN		0x00002004
+			MX51_PAD_DISP2_DAT13__FEC_TX_CLK	0x00002180
+			MX51_PAD_DISP2_DAT12__FEC_RX_DV		0x000020a4
+			MX51_PAD_EIM_A20__GPIO2_14		0x00000085 /* Phy Reset */
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX51_PAD_KEY_COL4__I2C2_SCL		0x400001ed
+			MX51_PAD_KEY_COL5__I2C2_SDA		0x400001ed
+		>;
+	};
+
+	pinctrl_lcd: lcdgrp {
+		fsl,pins = <
+			MX51_PAD_DISP1_DAT0__DISP1_DAT0		0x5
+			MX51_PAD_DISP1_DAT1__DISP1_DAT1		0x5
+			MX51_PAD_DISP1_DAT2__DISP1_DAT2		0x5
+			MX51_PAD_DISP1_DAT3__DISP1_DAT3		0x5
+			MX51_PAD_DISP1_DAT4__DISP1_DAT4		0x5
+			MX51_PAD_DISP1_DAT5__DISP1_DAT5		0x5
+			MX51_PAD_DISP1_DAT6__DISP1_DAT6		0x5
+			MX51_PAD_DISP1_DAT7__DISP1_DAT7		0x5
+			MX51_PAD_DISP1_DAT8__DISP1_DAT8		0x5
+			MX51_PAD_DISP1_DAT9__DISP1_DAT9		0x5
+			MX51_PAD_DISP1_DAT10__DISP1_DAT10	0x5
+			MX51_PAD_DISP1_DAT11__DISP1_DAT11	0x5
+			MX51_PAD_DISP1_DAT12__DISP1_DAT12	0x5
+			MX51_PAD_DISP1_DAT13__DISP1_DAT13	0x5
+			MX51_PAD_DISP1_DAT14__DISP1_DAT14	0x5
+			MX51_PAD_DISP1_DAT15__DISP1_DAT15	0x5
+			MX51_PAD_DISP1_DAT16__DISP1_DAT16	0x5
+			MX51_PAD_DISP1_DAT17__DISP1_DAT17	0x5
+			MX51_PAD_DISP1_DAT18__DISP1_DAT18	0x5
+			MX51_PAD_DISP1_DAT19__DISP1_DAT19	0x5
+			MX51_PAD_DISP1_DAT20__DISP1_DAT20	0x5
+			MX51_PAD_DISP1_DAT21__DISP1_DAT21	0x5
+			MX51_PAD_DISP1_DAT22__DISP1_DAT22	0x5
+			MX51_PAD_DISP1_DAT23__DISP1_DAT23	0x5
+			MX51_PAD_DI1_PIN2__DI1_PIN2		0x5
+			MX51_PAD_DI1_PIN3__DI1_PIN3		0x5
+			MX51_PAD_DI2_DISP_CLK__DI2_DISP_CLK	0x5
+			MX51_PAD_DI_GP4__DI2_PIN15		0x5
+		>;
+	};
+
+	pinctrl_pwm_backlight: backlightgrp {
+		fsl,pins = <
+			MX51_PAD_GPIO1_2__PWM1_PWMO		0x80000000
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX51_PAD_UART1_RXD__UART1_RXD		0x1c5
+			MX51_PAD_UART1_TXD__UART1_TXD		0x1c5
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX51_PAD_UART2_RXD__UART2_RXD		0x1c5
+			MX51_PAD_UART2_TXD__UART2_TXD		0x1c5
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX51_PAD_EIM_D25__UART3_RXD		0x1c5
+			MX51_PAD_EIM_D26__UART3_TXD		0x1c5
+		>;
+	};
+
+	pinctrl_weim: weimgrp {
+		fsl,pins = <
+			MX51_PAD_EIM_DTACK__EIM_DTACK		0x85
+			MX51_PAD_EIM_CS0__EIM_CS0		0x0
+			MX51_PAD_EIM_CS1__EIM_CS1		0x0
+			MX51_PAD_EIM_EB0__EIM_EB0		0x85
+			MX51_PAD_EIM_EB1__EIM_EB1		0x85
+			MX51_PAD_EIM_OE__EIM_OE			0x85
+			MX51_PAD_EIM_LBA__EIM_LBA		0x85
+		>;
+	};
+};

arch/arm/boot/dts/imx6dl.dtsi

@@ -104,10 +104,15 @@ display-subsystem {
 		compatible = "fsl,imx-display-subsystem";
 		ports = <&ipu1_di0>, <&ipu1_di1>;
 	};
+
+	gpu-subsystem {
+		compatible = "fsl,imx-gpu-subsystem";
+		cores = <&gpu_2d>, <&gpu_3d>;
+	};
 };
 
 &gpt {
-	compatible = "fsl,imx6dl-gpt", "fsl,imx6q-gpt";
+	compatible = "fsl,imx6dl-gpt";
 };
 
 &hdmi {

arch/arm/boot/dts/imx6q-gw5400-a.dts

@@ -154,7 +154,7 @@ flash: m25p80@0 {
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6q-novena.dts

+/*
+ * Copyright 2015 Sutajio Ko-Usagi PTE LTD
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of
+ *     the License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Kosagi Novena Dual/Quad";
+	compatible = "kosagi,imx6q-novena", "fsl,imx6q";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 10000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight_novena>;
+		power-supply = <&reg_lvds_lcd>;
+		brightness-levels = <0 3 6 12 16 24 32 48 64 96 128 192 255>;
+		default-brightness-level = <12>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys_novena>;
+
+		user-button {
+			label = "User Button";
+			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+		};
+
+		lid {
+			label = "Lid";
+			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+			linux,input-type = <5>;	/* EV_SW */
+			linux,code = <0>;	/* SW_LID */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds_novena>;
+
+		heartbeat {
+			label = "novena:white:panel";
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	panel: panel {
+		compatible = "innolux,n133hse-ea1", "simple-panel";
+		backlight = <&backlight>;
+	};
+
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_audio_codec: regulator-audio-codec {
+		compatible = "regulator-fixed";
+		regulator-name = "es8328-power";
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <400000>;
+		gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_display: regulator-display {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-display-power";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <200000>;
+		gpio = <&gpio5 28 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_lvds_lcd: regulator-lvds-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-lvds-power";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_pcie: regulator-pcie {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie-bus-power";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_sata: regulator-sata {
+		compatible = "regulator-fixed";
+		regulator-name = "sata-power";
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <10000>;
+		gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-es8328";
+		model = "imx-audio-es8328";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-amp-supply = <&reg_audio_codec>;
+		jack-gpio = <&gpio5 15 GPIO_ACTIVE_HIGH>;
+		audio-routing =
+			"Speaker", "LOUT2",
+			"Speaker", "ROUT2",
+			"Speaker", "audio-amp",
+			"Headphone", "ROUT1",
+			"Headphone", "LOUT1",
+			"LINPUT1", "Mic Jack",
+			"RINPUT1", "Mic Jack",
+			"Mic Jack", "Mic Bias";
+		mux-int-port = <0x1>;
+		mux-ext-port = <0x3>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux_novena>;
+	status = "okay";
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3_novena>;
+	fsl,spi-num-chipselects = <3>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet_novena>;
+	phy-mode = "rgmii";
+	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+	rxc-skew-ps = <3000>;
+	rxdv-skew-ps = <0>;
+	txc-skew-ps = <3000>;
+	txen-skew-ps = <0>;
+	rxd0-skew-ps = <0>;
+	rxd1-skew-ps = <0>;
+	rxd2-skew-ps = <0>;
+	rxd3-skew-ps = <0>;
+	txd0-skew-ps = <3000>;
+	txd1-skew-ps = <3000>;
+	txd2-skew-ps = <3000>;
+	txd3-skew-ps = <3000>;
+	status = "okay";
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi_novena>;
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1_novena>;
+	status = "okay";
+
+	accel: mma8452@1c {
+		compatible = "fsl,mma8452";
+		reg = <0x1c>;
+	};
+
+	rtc: pcf8523@68 {
+		compatible = "nxp,pcf8523";
+		reg = <0x68>;
+	};
+
+	sbs_battery: bq20z75@0b {
+		compatible = "sbs,sbs-battery";
+		reg = <0x0b>;
+		sbs,i2c-retry-count = <50>;
+	};
+
+	touch: stmpe811@44 {
+		compatible = "st,stmpe811";
+		reg = <0x44>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		irq-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+		id = <0>;
+		blocks = <0x5>;
+		irq-trigger = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_stmpe_novena>;
+		vio-supply = <&reg_3p3v>;
+		vcc-supply = <&reg_3p3v>;
+
+		stmpe_touchscreen {
+			compatible = "st,stmpe-ts";
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <1>;
+			st,touch-det-delay = <2>;
+			st,settling = <2>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2_novena>;
+	status = "okay";
+
+	pmic: pfuze100@08 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			reg_sw1a: sw1a {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			reg_sw1c: sw1c {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_sw2: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_sw3a: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_sw3b: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_sw4: sw4 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_swbst: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+				regulator-boot-on;
+			};
+
+			reg_snvs: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vref: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vgen1: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			reg_vgen2: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			reg_vgen3: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_vgen4: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			reg_vgen5: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			reg_vgen6: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3_novena>;
+	status = "okay";
+
+	codec: es8328@11 {
+		compatible = "everest,es8328";
+		reg = <0x11>;
+		DVDD-supply = <&reg_audio_codec>;
+		AVDD-supply = <&reg_audio_codec>;
+		PVDD-supply = <&reg_audio_codec>;
+		HPVDD-supply = <&reg_audio_codec>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sound_novena>;
+		clocks = <&clks IMX6QDL_CLK_CKO1>;
+		assigned-clocks = <&clks IMX6QDL_CLK_CKO>,
+				  <&clks IMX6QDL_CLK_CKO1_SEL>,
+				  <&clks IMX6QDL_CLK_PLL4_AUDIO>,
+				  <&clks IMX6QDL_CLK_CKO1>;
+		assigned-clock-parents = <&clks IMX6QDL_CLK_CKO1>,
+					 <&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>,
+					 <&clks IMX6QDL_CLK_OSC>,
+					 <&clks IMX6QDL_CLK_CKO1_PODF>;
+		assigned-clock-rates = <0 0 722534400 22579200>;
+	};
+};
+
+&kpp {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_kpp_novena>;
+	linux,keymap = <
+		MATRIX_KEY(1, 1, KEY_CONFIG)
+	>;
+	status = "okay";
+};
+
+&ldb {
+	fsl,dual-channel;
+	status = "okay";
+
+	lvds-channel@0 {
+		fsl,data-mapping = "jeida";
+		fsl,data-width = <24>;
+		fsl,panel = <&panel>;
+		status = "okay";
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie_novena>;
+	reset-gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&sata {
+	target-supply = <&reg_sata>;
+	fsl,transmit-level-mV = <1025>;
+	fsl,transmit-boost-mdB = <0>;
+	fsl,transmit-atten-16ths = <8>;
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2_novena>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3_novena>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4_novena>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	dr_mode = "otg";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg_novena>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_swbst>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2_novena>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3_novena>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_audmux_novena: audmuxgrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+		>;
+	};
+
+	pinctrl_backlight_novena: backlightgrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28	0x1b0b1
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b1
+		>;
+	};
+
+	pinctrl_ecspi3_novena: ecspi3grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+		>;
+	};
+
+	pinctrl_enet_novena: enetgrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b020
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b028
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b028
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b028
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b028
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b028
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+			/* Ethernet reset */
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x1b0b1
+		>;
+	};
+
+	pinctrl_fpga_gpio: fpgagpiogrp-novena {
+		fsl,pins = <
+			/* FPGA power */
+			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17		0x1b0b1
+			/* Reset */
+			MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07	0x1b0b1
+			/* FPGA GPIOs */
+			MX6QDL_PAD_EIM_DA0__GPIO3_IO00		0x1b0b1
+			MX6QDL_PAD_EIM_DA1__GPIO3_IO01		0x1b0b1
+			MX6QDL_PAD_EIM_DA2__GPIO3_IO02		0x1b0b1
+			MX6QDL_PAD_EIM_DA3__GPIO3_IO03		0x1b0b1
+			MX6QDL_PAD_EIM_DA4__GPIO3_IO04		0x1b0b1
+			MX6QDL_PAD_EIM_DA5__GPIO3_IO05		0x1b0b1
+			MX6QDL_PAD_EIM_DA6__GPIO3_IO06		0x1b0b1
+			MX6QDL_PAD_EIM_DA7__GPIO3_IO07		0x1b0b1
+			MX6QDL_PAD_EIM_DA8__GPIO3_IO08		0x1b0b1
+			MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0x1b0b1
+			MX6QDL_PAD_EIM_DA10__GPIO3_IO10		0x1b0b1
+			MX6QDL_PAD_EIM_DA11__GPIO3_IO11		0x1b0b1
+			MX6QDL_PAD_EIM_DA12__GPIO3_IO12		0x1b0b1
+			MX6QDL_PAD_EIM_DA13__GPIO3_IO13		0x1b0b1
+			MX6QDL_PAD_EIM_DA14__GPIO3_IO14		0x1b0b1
+			MX6QDL_PAD_EIM_DA15__GPIO3_IO15		0x1b0b1
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22		0x1b0b1
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21		0x1b0b1
+			MX6QDL_PAD_EIM_A18__GPIO2_IO20		0x1b0b1
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23		0x1b0b1
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24		0x1b0b1
+			MX6QDL_PAD_EIM_LBA__GPIO2_IO27		0x1b0b1
+			MX6QDL_PAD_EIM_OE__GPIO2_IO25		0x1b0b1
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26		0x1b0b1
+			MX6QDL_PAD_EIM_WAIT__GPIO5_IO00		0x1b0b1
+			MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0x1b0b1
+		>;
+	};
+
+	pinctrl_fpga_eim: fpgaeimgrp-novena {
+		fsl,pins = <
+			/* FPGA power */
+			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17		0x1b0b1
+			/* Reset */
+			MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07	0x1b0b1
+			/* FPGA GPIOs */
+			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0f1
+			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0f1
+			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0f1
+			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0f1
+			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0f1
+			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0f1
+			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0f1
+			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0f1
+			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0f1
+			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0f1
+			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0f1
+			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0f1
+			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0f1
+			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0f1
+			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0f1
+			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0f1
+			MX6QDL_PAD_EIM_A16__EIM_ADDR16		0xb0f1
+			MX6QDL_PAD_EIM_A17__EIM_ADDR17		0xb0f1
+			MX6QDL_PAD_EIM_A18__EIM_ADDR18		0xb0f1
+			MX6QDL_PAD_EIM_CS0__EIM_CS0_B		0xb0f1
+			MX6QDL_PAD_EIM_CS1__EIM_CS1_B		0xb0f1
+			MX6QDL_PAD_EIM_LBA__EIM_LBA_B		0xb0f1
+			MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0f1
+			MX6QDL_PAD_EIM_RW__EIM_RW		0xb0f1
+			MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B		0xb0f1
+			MX6QDL_PAD_EIM_BCLK__EIM_BCLK		0xb0f1
+		>;
+	};
+
+	pinctrl_gpio_keys_novena: gpiokeysgrp-novena {
+		fsl,pins = <
+			/* User button */
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0
+			/* PCIe Wakeup */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x1f0e0
+			/* Lid switch */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x1b0b0
+		>;
+	};
+
+	pinctrl_hdmi_novena: hdmigrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE	0x1f8b0
+			MX6QDL_PAD_EIM_A24__GPIO5_IO04		0x1b0b1
+		>;
+	};
+
+	pinctrl_i2c1_novena: i2c1grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2_novena: i2c2grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_EB2__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D16__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3_novena: i2c3grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D18__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_kpp_novena: kppgrp-novena {
+		fsl,pins = <
+			/* Front panel button */
+			MX6QDL_PAD_KEY_ROW1__KEY_ROW1		0x1b0b1
+			/* Fake column driver, not connected */
+			MX6QDL_PAD_KEY_COL1__KEY_COL1		0x1b0b1
+		>;
+	};
+
+	pinctrl_leds_novena: ledsgrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__GPIO1_IO21		0x1b0b1
+		>;
+	};
+
+	pinctrl_pcie_novena: pciegrp-novena {
+		fsl,pins = <
+			/* Reset */
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x1b0b1
+			/* Power On */
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x1b0b1
+			/* Wifi kill */
+			MX6QDL_PAD_EIM_A22__GPIO2_IO16		0x1b0b1
+		>;
+	};
+
+	pinctrl_sata_novena: satagrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D30__GPIO3_IO30		0x1b0b1
+		>;
+	};
+
+	pinctrl_senoko_novena: senokogrp-novena {
+		fsl,pins = <
+			/* Senoko IRQ line */
+			MX6QDL_PAD_SD1_CLK__GPIO1_IO20		0x13048
+			/* Senoko reset line */
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x1b0b1
+		>;
+	};
+
+	pinctrl_sound_novena: soundgrp-novena {
+		fsl,pins = <
+			/* Audio power regulator */
+			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b1
+			/* Headphone plug */
+			MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x1b0b1
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x000b0
+		>;
+	};
+
+	pinctrl_stmpe_novena: stmpegrp-novena {
+		fsl,pins = <
+			/* Touchscreen interrupt */
+			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2_novena: uart2grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3_novena: uart3grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4_novena: uart4grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg_novena: usbotggrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_novena: usdhc2grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100f9
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+			/* Write protect */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b1
+			/* Card detect */
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc3_novena: usdhc3grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x170f9
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x170f9
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x170f9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x170f9
+		>;
+	};
+};

arch/arm/boot/dts/imx6q.dtsi

@@ -14,6 +14,7 @@
 
 / {
 	aliases {
+		ipu1 = &ipu2;
 		spi4 = &ecspi5;
 	};
 
@@ -153,6 +154,16 @@ sata: sata@02200000 {
 			status = "disabled";
 		};
 
+		gpu_vg: gpu@02204000 {
+			compatible = "vivante,gc";
+			reg = <0x02204000 0x4000>;
+			interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clks IMX6QDL_CLK_OPENVG_AXI>,
+				 <&clks IMX6QDL_CLK_GPU2D_CORE>;
+			clock-names = "bus", "core";
+			power-domains = <&gpc 1>;
+		};
+
 		ipu2: ipu@02800000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -225,6 +236,11 @@ display-subsystem {
 		compatible = "fsl,imx-display-subsystem";
 		ports = <&ipu1_di0>, <&ipu1_di1>, <&ipu2_di0>, <&ipu2_di1>;
 	};
+
+	gpu-subsystem {
+		compatible = "fsl,imx-gpu-subsystem";
+		cores = <&gpu_2d>, <&gpu_3d>, <&gpu_vg>;
+	};
 };
 
 &hdmi {

arch/arm/boot/dts/imx6qdl-gw51xx.dtsi

@@ -94,7 +94,7 @@ reg_usb_otg_vbus: regulator@2 {
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
@@ -174,6 +174,24 @@ &pcie {
 	status = "okay";
 };
 
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */
+	status = "disabled";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
@@ -294,6 +312,24 @@ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1b0b1
 			>;
 		};
 
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm3: pwm3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm4: pwm4grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT2__PWM4_OUT		0x1b0b1
+			>;
+		};
+
 		pinctrl_uart1: uart1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1

arch/arm/boot/dts/imx6qdl-gw52xx.dtsi

@@ -151,10 +151,25 @@ &can1 {
 	status = "okay";
 };
 
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+	                  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+	                  <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&ecspi3 {
+	fsl,spi-num-chipselects = <1>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	status = "okay";
+};
+
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
@@ -275,6 +290,18 @@ &pcie {
 	status = "okay";
 };
 
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
 &pwm4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
@@ -338,6 +365,15 @@ MX6QDL_PAD_GPIO_0__CCM_CLKO1	0x130b0 /* AUD4_MCK */
 			>;
 		};
 
+		pinctrl_ecspi3: escpi3grp {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+				MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+				MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+				MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24	0x100b1
+			>;
+		};
+
 		pinctrl_enet: enetgrp {
 			fsl,pins = <
 				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
@@ -429,6 +465,18 @@ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1b0b1
 			>;
 		};
 
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm3: pwm3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+			>;
+		};
+
 		pinctrl_pwm4: pwm4grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1

arch/arm/boot/dts/imx6qdl-gw53xx.dtsi

@@ -152,10 +152,17 @@ &can1 {
 	status = "okay";
 };
 
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+	                  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+	                  <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
@@ -247,7 +254,7 @@ touchscreen: egalax_ts@04 {
 &ldb {
 	status = "okay";
 
-	lvds-channel@1 {
+	lvds-channel@0 {
 		fsl,data-mapping = "spwg";
 		fsl,data-width = <18>;
 		status = "okay";
@@ -280,6 +287,18 @@ eth1: sky2@8 { /* MAC/PHY on bus 8 */
 	};
 };
 
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
 &pwm4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
@@ -435,6 +454,18 @@ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1b0b1
 			>;
 		};
 
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm3: pwm3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+			>;
+		};
+
 		pinctrl_pwm4: pwm4grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1

arch/arm/boot/dts/imx6qdl-gw54xx.dtsi

@@ -142,10 +142,17 @@ &can1 {
 	status = "okay";
 };
 
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+	                  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+	                  <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
@@ -260,6 +267,8 @@ sw4_reg: sw4 {
 			swbst_reg: swbst {
 				regulator-min-microvolt = <5000000>;
 				regulator-max-microvolt = <5150000>;
+				regulator-boot-on;
+				regulator-always-on;
 			};
 
 			snvs_reg: vsnvs {
@@ -336,7 +345,7 @@ touchscreen: egalax_ts@04 {
 &ldb {
 	status = "okay";
 
-	lvds-channel@1 {
+	lvds-channel@0 {
 		fsl,data-mapping = "spwg";
 		fsl,data-width = <18>;
 		status = "okay";
@@ -369,6 +378,24 @@ eth1: sky2@8 { /* MAC/PHY on bus 8 */
 	};
 };
 
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>; /* MX6_DIO0 */
+	status = "disabled";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
 &pwm4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
@@ -528,6 +555,24 @@ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1b0b1
 			>;
 		};
 
+		pinctrl_pwm1: pwm1grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_9__PWM1_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm3: pwm3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+			>;
+		};
+
 		pinctrl_pwm4: pwm4grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1

arch/arm/boot/dts/imx6qdl-gw551x.dtsi

@@ -198,6 +198,18 @@ &pcie {
 	status = "okay";
 };
 
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
 &ssi1 {
 	status = "okay";
 };
@@ -290,6 +302,18 @@ MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0 /* PCIE RST */
 			>;
 		};
 
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm3: pwm3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
+			>;
+		};
+
 		pinctrl_uart2: uart2grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1

arch/arm/boot/dts/imx6qdl-gw552x.dtsi

@@ -164,6 +164,18 @@ &pcie {
 	status = "okay";
 };
 
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
 &uart2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2>;
@@ -242,6 +254,18 @@ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x1b0b0
 			>;
 		};
 
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm3: pwm3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+			>;
+		};
+
 		pinctrl_uart2: uart2grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1

arch/arm/boot/dts/imx6qdl-sabreauto.dtsi

@@ -113,14 +113,14 @@ backlight {
 &clks {
 	assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>,
 			  <&clks IMX6QDL_PLL4_BYPASS>,
-			  <&clks IMX6QDL_CLK_PLL4_POST_DIV>,
 			  <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
+			  <&clks IMX6QDL_CLK_PLL4_POST_DIV>;
 	assigned-clock-parents = <&clks IMX6QDL_CLK_LVDS2_IN>,
 				 <&clks IMX6QDL_PLL4_BYPASS_SRC>,
 				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
 				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-	assigned-clock-rates = <0>, <0>, <24576000>;
+	assigned-clock-rates = <0>, <0>, <0>, <0>, <24576000>;
 };
 
 &ecspi1 {

arch/arm/boot/dts/imx6qdl.dtsi

@@ -30,6 +30,7 @@ aliases {
 		i2c0 = &i2c1;
 		i2c1 = &i2c2;
 		i2c2 = &i2c3;
+		ipu0 = &ipu1;
 		mmc0 = &usdhc1;
 		mmc1 = &usdhc2;
 		mmc2 = &usdhc3;
@@ -47,15 +48,6 @@ aliases {
 		usbphy1 = &usbphy2;
 	};
 
-	intc: interrupt-controller@00a01000 {
-		compatible = "arm,cortex-a9-gic";
-		#interrupt-cells = <3>;
-		interrupt-controller;
-		reg = <0x00a01000 0x1000>,
-		      <0x00a00100 0x100>;
-		interrupt-parent = <&intc>;
-	};
-
 	clocks {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -147,6 +139,27 @@ hdmi_mux_1: endpoint {
 			};
 		};
 
+		gpu_3d: gpu@00130000 {
+			compatible = "vivante,gc";
+			reg = <0x00130000 0x4000>;
+			interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clks IMX6QDL_CLK_GPU3D_AXI>,
+				 <&clks IMX6QDL_CLK_GPU3D_CORE>,
+				 <&clks IMX6QDL_CLK_GPU3D_SHADER>;
+			clock-names = "bus", "core", "shader";
+			power-domains = <&gpc 1>;
+		};
+
+		gpu_2d: gpu@00134000 {
+			compatible = "vivante,gc";
+			reg = <0x00134000 0x4000>;
+			interrupts = <0 10 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clks IMX6QDL_CLK_GPU2D_AXI>,
+				 <&clks IMX6QDL_CLK_GPU2D_CORE>;
+			clock-names = "bus", "core";
+			power-domains = <&gpc 1>;
+		};
+
 		timer@00a00600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x00a00600 0x20>;
@@ -155,6 +168,15 @@ timer@00a00600 {
 			clocks = <&clks IMX6QDL_CLK_TWD>;
 		};
 
+		intc: interrupt-controller@00a01000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x00a01000 0x1000>,
+			      <0x00a00100 0x100>;
+			interrupt-parent = <&intc>;
+		};
+
 		L2: l2-cache@00a02000 {
 			compatible = "arm,pl310-cache";
 			reg = <0x00a02000 0x1000>;
@@ -173,8 +195,7 @@ pcie: pcie@0x01000000 {
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
-			ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 /* configuration space */
-				  0x81000000 0 0          0x01f80000 0 0x00010000 /* downstream I/O */
+			ranges = <0x81000000 0 0          0x01f80000 0 0x00010000 /* downstream I/O */
 				  0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */
 			num-lanes = <1>;
 			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
@@ -227,7 +248,7 @@ spdif: spdif@02004000 {
 						      "rxtx1", "rxtx2",
 						      "rxtx3", "rxtx4",
 						      "rxtx5", "rxtx6",
-						      "rxtx7", "dma";
+						      "rxtx7", "spba";
 					status = "disabled";
 				};
 
@@ -309,7 +330,7 @@ esai: esai@02024000 {
 						 <&clks IMX6QDL_CLK_ESAI_EXTAL>,
 						 <&clks IMX6QDL_CLK_ESAI_IPG>,
 						 <&clks IMX6QDL_CLK_SPBA>;
-					clock-names = "core", "mem", "extal", "fsys", "dma";
+					clock-names = "core", "mem", "extal", "fsys", "spba";
 					dmas = <&sdma 23 21 0>, <&sdma 24 21 0>;
 					dma-names = "rx", "tx";
 					status = "disabled";
@@ -378,7 +399,7 @@ asrc: asrc@02034000 {
 						"asrck_1", "asrck_2", "asrck_3", "asrck_4",
 						"asrck_5", "asrck_6", "asrck_7", "asrck_8",
 						"asrck_9", "asrck_a", "asrck_b", "asrck_c",
-						"asrck_d", "asrck_e", "asrck_f", "dma";
+						"asrck_d", "asrck_e", "asrck_f", "spba";
 					dmas = <&sdma 17 23 1>, <&sdma 18 23 1>, <&sdma 19 23 1>,
 						<&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>;
 					dma-names = "rxa", "rxb", "rxc",
@@ -906,6 +927,9 @@ usbotg: usb@02184000 {
 				clocks = <&clks IMX6QDL_CLK_USBOH3>;
 				fsl,usbphy = <&usbphy1>;
 				fsl,usbmisc = <&usbmisc 0>;
+				ahb-burst-config = <0x0>;
+				tx-burst-size-dword = <0x10>;
+				rx-burst-size-dword = <0x10>;
 				status = "disabled";
 			};
 
@@ -917,6 +941,9 @@ usbh1: usb@02184200 {
 				fsl,usbphy = <&usbphy2>;
 				fsl,usbmisc = <&usbmisc 1>;
 				dr_mode = "host";
+				ahb-burst-config = <0x0>;
+				tx-burst-size-dword = <0x10>;
+				rx-burst-size-dword = <0x10>;
 				status = "disabled";
 			};
 
@@ -927,6 +954,9 @@ usbh2: usb@02184400 {
 				clocks = <&clks IMX6QDL_CLK_USBOH3>;
 				fsl,usbmisc = <&usbmisc 2>;
 				dr_mode = "host";
+				ahb-burst-config = <0x0>;
+				tx-burst-size-dword = <0x10>;
+				rx-burst-size-dword = <0x10>;
 				status = "disabled";
 			};
 
@@ -937,6 +967,9 @@ usbh3: usb@02184600 {
 				clocks = <&clks IMX6QDL_CLK_USBOH3>;
 				fsl,usbmisc = <&usbmisc 3>;
 				dr_mode = "host";
+				ahb-burst-config = <0x0>;
+				tx-burst-size-dword = <0x10>;
+				rx-burst-size-dword = <0x10>;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/imx6sl.dtsi

@@ -151,7 +151,7 @@ spdif: spdif@02004000 {
 						"rxtx1", "rxtx2",
 						"rxtx3", "rxtx4",
 						"rxtx5", "rxtx6",
-						"rxtx7", "dma";
+						"rxtx7", "spba";
 					status = "disabled";
 				};
 
@@ -708,6 +708,9 @@ usbotg1: usb@02184000 {
 				clocks = <&clks IMX6SL_CLK_USBOH3>;
 				fsl,usbphy = <&usbphy1>;
 				fsl,usbmisc = <&usbmisc 0>;
+				ahb-burst-config = <0x0>;
+				tx-burst-size-dword = <0x10>;
+				rx-burst-size-dword = <0x10>;
 				status = "disabled";
 			};
 
@@ -718,6 +721,9 @@ usbotg2: usb@02184200 {
 				clocks = <&clks IMX6SL_CLK_USBOH3>;
 				fsl,usbphy = <&usbphy2>;
 				fsl,usbmisc = <&usbmisc 1>;
+				ahb-burst-config = <0x0>;
+				tx-burst-size-dword = <0x10>;
+				rx-burst-size-dword = <0x10>;
 				status = "disabled";
 			};
 
@@ -728,6 +734,9 @@ usbh: usb@02184400 {
 				clocks = <&clks IMX6SL_CLK_USBOH3>;
 				fsl,usbmisc = <&usbmisc 2>;
 				dr_mode = "host";
+				ahb-burst-config = <0x0>;
+				tx-burst-size-dword = <0x10>;
+				rx-burst-size-dword = <0x10>;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/imx6sx.dtsi

@@ -222,7 +222,7 @@ spdif: spdif@02004000 {
 						      "rxtx1", "rxtx2",
 						      "rxtx3", "rxtx4",
 						      "rxtx5", "rxtx6",
-						      "rxtx7", "dma";
+						      "rxtx7", "spba";
 					status = "disabled";
 				};
 
@@ -295,7 +295,7 @@ esai: esai@02024000 {
 						 <&clks IMX6SX_CLK_ESAI_IPG>,
 						 <&clks IMX6SX_CLK_SPBA>;
 					clock-names = "core", "mem", "extal",
-						      "fsys", "dma";
+						      "fsys", "spba";
 					status = "disabled";
 				};
 
@@ -348,7 +348,7 @@ asrc: asrc@02034000 {
 						 <&clks IMX6SX_CLK_ASRC_IPG>,
 						 <&clks IMX6SX_CLK_SPDIF>,
 						 <&clks IMX6SX_CLK_SPBA>;
-					clock-names = "mem", "ipg", "asrck", "dma";
+					clock-names = "mem", "ipg", "asrck", "spba";
 					dmas = <&sdma 17 20 1>, <&sdma 18 20 1>,
 					       <&sdma 19 20 1>, <&sdma 20 20 1>,
 					       <&sdma 21 20 1>, <&sdma 22 20 1>;
@@ -783,6 +783,9 @@ usbotg1: usb@02184000 {
 				fsl,usbphy = <&usbphy1>;
 				fsl,usbmisc = <&usbmisc 0>;
 				fsl,anatop = <&anatop>;
+				ahb-burst-config = <0x0>;
+				tx-burst-size-dword = <0x10>;
+				rx-burst-size-dword = <0x10>;
 				status = "disabled";
 			};
 
@@ -793,6 +796,9 @@ usbotg2: usb@02184200 {
 				clocks = <&clks IMX6SX_CLK_USBOH3>;
 				fsl,usbphy = <&usbphy2>;
 				fsl,usbmisc = <&usbmisc 1>;
+				ahb-burst-config = <0x0>;
+				tx-burst-size-dword = <0x10>;
+				rx-burst-size-dword = <0x10>;
 				status = "disabled";
 			};
 
@@ -805,6 +811,9 @@ usbh: usb@02184400 {
 				phy_type = "hsic";
 				fsl,anatop = <&anatop>;
 				dr_mode = "host";
+				ahb-burst-config = <0x0>;
+				tx-burst-size-dword = <0x10>;
+				rx-burst-size-dword = <0x10>;
 				status = "disabled";
 			};
 
@@ -1152,6 +1161,8 @@ adc1: adc@02280000 {
 				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SX_CLK_IPG>;
 				clock-names = "adc";
+				fsl,adck-max-frequency = <30000000>, <40000000>,
+							 <20000000>;
 				status = "disabled";
                         };
 
@@ -1161,6 +1172,8 @@ adc2: adc@02284000 {
 				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SX_CLK_IPG>;
 				clock-names = "adc";
+				fsl,adck-max-frequency = <30000000>, <40000000>,
+							 <20000000>;
 				status = "disabled";
                         };
 

arch/arm/boot/dts/imx6ul.dtsi

@@ -548,6 +548,9 @@ usbotg1: usb@02184000 {
 				fsl,usbphy = <&usbphy1>;
 				fsl,usbmisc = <&usbmisc 0>;
 				fsl,anatop = <&anatop>;
+				ahb-burst-config = <0x0>;
+				tx-burst-size-dword = <0x10>;
+				rx-burst-size-dword = <0x10>;
 				status = "disabled";
 			};
 
@@ -558,6 +561,9 @@ usbotg2: usb@02184200 {
 				clocks = <&clks IMX6UL_CLK_USBOH3>;
 				fsl,usbphy = <&usbphy2>;
 				fsl,usbmisc = <&usbmisc 1>;
+				ahb-burst-config = <0x0>;
+				tx-burst-size-dword = <0x10>;
+				rx-burst-size-dword = <0x10>;
 				status = "disabled";
 			};
 
@@ -619,6 +625,18 @@ usdhc2: usdhc@02194000 {
 				status = "disabled";
 			};
 
+			adc1: adc@02198000 {
+				compatible = "fsl,imx6ul-adc", "fsl,vf610-adc";
+				reg = <0x02198000 0x4000>;
+				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_ADC1>;
+				num-channels = <2>;
+				clock-names = "adc";
+				fsl,adck-max-frequency = <30000000>, <40000000>,
+							 <20000000>;
+				status = "disabled";
+			};
+
 			i2c1: i2c@021a0000 {
 				#address-cells = <1>;
 				#size-cells = <0>;

arch/arm/boot/dts/imx7d-cl-som-imx7.dts

+/*
+ * Support for CompuLab CL-SOM-iMX7 System-on-Module
+ *
+ * Copyright (C) 2015 CompuLab Ltd. - http://www.compulab.co.il/
+ * Author: Ilya Ledvich <ilya@compulab.co.il>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "imx7d.dtsi"
+
+/ {
+	model = "CompuLab CL-SOM-iMX7";
+	compatible = "compulab,cl-som-imx7", "fsl,imx7d";
+
+	memory {
+		reg = <0x80000000 0x10000000>; /* 256 MB - minimal configuration */
+	};
+
+	reg_usb_otg1_vbus: regulator-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&cpu0 {
+	arm-supply = <&sw1a_reg>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+
+		ethphy1: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	assigned-clocks = <&clks IMX7D_ENET2_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET2_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pmic: pmic@8 {
+		compatible = "fsl,pfuze3000";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1a {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1475000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			/* use sw1c_reg to align with pfuze100/pfuze200 */
+			sw1c_reg: sw1b {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1475000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vldo1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vldo2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vccsd {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: v33 {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vldo3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vldo4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	pca9555: pca9555@20 {
+		compatible = "nxp,pca9555";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0x20>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c08";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
+	assigned-clock-rates = <400000000>;
+	bus-width = <8>;
+	fsl,tuning-step = <2>;
+	non-removable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX7D_PAD_SD2_CD_B__ENET1_MDIO			0x3
+			MX7D_PAD_SD2_WP__ENET1_MDC			0x3
+			MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC	0x1
+			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x1
+			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x1
+			MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2	0x1
+			MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3	0x1
+			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x1
+			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC	0x1
+			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x1
+			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x1
+			MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x1
+			MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x1
+			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x1
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC		0x1
+			MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0		0x1
+			MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1		0x1
+			MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2		0x1
+			MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3		0x1
+			MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL		0x1
+			MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC		0x1
+			MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0		0x1
+			MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1		0x1
+			MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2		0x1
+			MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3		0x1
+			MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL		0x1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX7D_PAD_I2C2_SDA__I2C2_SDA		0x4000007f
+			MX7D_PAD_I2C2_SCL__I2C2_SCL		0x4000007f
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX	0x79
+			MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX	0x79
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO05__GPIO1_IO5		0x14 /* OTG PWREN */
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x19
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x59
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x59
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x59
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x59
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x59
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x59
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x59
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x59
+			MX7D_PAD_SD3_STROBE__SD3_STROBE		0x19
+		>;
+	};
+};

arch/arm/boot/dts/imx7d-sbc-imx7.dts

+/*
+ * Support for CompuLab SBC-iMX7 Single Board Computer
+ *
+ * Copyright (C) 2015 CompuLab Ltd. - http://www.compulab.co.il/
+ * Author: Ilya Ledvich <ilya@compulab.co.il>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ */
+
+#include "imx7d-cl-som-imx7.dts"
+
+/ {
+	model = "CompuLab SBC-iMX7";
+	compatible = "compulab,sbc-imx7", "compulab,cl-som-imx7", "fsl,imx7d";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+	enable-sdio-wakeup;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x59
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x19
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x59
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x59
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x59
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x59
+			MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x59 /* CD */
+			MX7D_PAD_SD1_WP__GPIO5_IO1		0x59 /* WP */
+		>;
+	};
+};

arch/arm/boot/dts/imx7d-sdb.dts

@@ -97,6 +97,16 @@ reg_vref_1v8: regulator@3 {
 	};
 };
 
+&adc1 {
+	vref-supply = <&reg_vref_1v8>;
+	status = "okay";
+};
+
+&adc2 {
+	vref-supply = <&reg_vref_1v8>;
+	status = "okay";
+};
+
 &cpu0 {
 	arm-supply = <&sw1a_reg>;
 };

arch/arm/boot/dts/imx7d.dtsi

@@ -85,9 +85,7 @@ cpu0: cpu@0 {
 				792000	975000
 			>;
 			clock-latency = <61036>; /* two CLK32 periods */
-			clocks = <&clks IMX7D_ARM_A7_ROOT_CLK>, <&clks IMX7D_ARM_A7_ROOT_SRC>,
-				 <&clks IMX7D_PLL_ARM_MAIN_CLK>, <&clks IMX7D_PLL_SYS_MAIN_CLK>;
-			clock-names = "arm", "arm_root_src", "pll_arm", "pll_sys_main";
+			clocks = <&clks IMX7D_CLK_ARM>;
 		};
 
 		cpu1: cpu@1 {
@@ -583,6 +581,24 @@ aips2: aips-bus@30400000 {
 			reg = <0x30400000 0x400000>;
 			ranges;
 
+			adc1: adc@30610000 {
+				compatible = "fsl,imx7d-adc";
+				reg = <0x30610000 0x10000>;
+				interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_ADC_ROOT_CLK>;
+				clock-names = "adc";
+				status = "disabled";
+			};
+
+			adc2: adc@30620000 {
+				compatible = "fsl,imx7d-adc";
+				reg = <0x30620000 0x10000>;
+				interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_ADC_ROOT_CLK>;
+				clock-names = "adc";
+				status = "disabled";
+			};
+
 			pwm1: pwm@30660000 {
 				compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
 				reg = <0x30660000 0x10000>;

arch/arm/boot/dts/ls1021a-qds.dts

@@ -320,6 +320,10 @@ &sai2 {
 	status = "okay";
 };
 
+&sata {
+	status = "okay";
+};
+
 &uart0 {
 	status = "okay";
 };

arch/arm/boot/dts/ls1021a-twr.dts

@@ -105,6 +105,15 @@ simple-audio-card,codec {
 			bitclock-master;
 		};
 	};
+
+	panel: panel {
+		compatible = "nec,nl4827hc19-05b";
+	};
+};
+
+&dcu {
+	fsl,panel = <&panel>;
+	status = "okay";
 };
 
 &dspi1 {
@@ -212,6 +221,10 @@ &sai1 {
 	status = "okay";
 };
 
+&sata {
+	status = "okay";
+};
+
 &uart0 {
 	status = "okay";
 };

arch/arm/boot/dts/ls1021a.dtsi

@@ -143,6 +143,17 @@ esdhc: esdhc@1560000 {
 			status = "disabled";
 		};
 
+		sata: sata@3200000 {
+			compatible = "fsl,ls1021a-ahci";
+			reg = <0x0 0x3200000 0x0 0x10000>,
+			      <0x0 0x20220520 0x0 0x4>;
+			reg-names = "ahci", "sata-ecc";
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&platform_clk 1>;
+			dma-coherent;
+			status = "disabled";
+		};
+
 		scfg: scfg@1570000 {
 			compatible = "fsl,ls1021a-scfg", "syscon";
 			reg = <0x0 0x1570000 0x0 0x10000>;
@@ -428,6 +439,16 @@ edma0: edma@2c00000 {
 				 <&platform_clk 1>;
 		};
 
+		dcu: dcu@2ce0000 {
+			compatible = "fsl,ls1021a-dcu";
+			reg = <0x0 0x2ce0000 0x0 0x10000>;
+			interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&platform_clk 0>;
+			clock-names = "dcu";
+			big-endian;
+			status = "disabled";
+		};
+
 		mdio0: mdio@2d24000 {
 			compatible = "gianfar";
 			device_type = "mdio";

arch/arm/boot/dts/vf-colibri.dtsi

@@ -23,6 +23,18 @@ &adc1 {
 	status = "okay";
 };
 
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan0>;
+	status = "disabled";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "disabled";
+};
+
 &dspi1 {
 	bus-num = <1>;
 	pinctrl-names = "default";
@@ -125,6 +137,20 @@ &usbphy1 {
 
 &iomuxc {
 	vf610-colibri {
+		pinctrl_flexcan0: can0grp {
+			fsl,pins = <
+				VF610_PAD_PTB14__CAN0_RX	0x31F1
+				VF610_PAD_PTB15__CAN0_TX	0x31F2
+			>;
+		};
+
+		pinctrl_flexcan1: can1grp {
+			fsl,pins = <
+				VF610_PAD_PTB16__CAN1_RX	0x31F1
+				VF610_PAD_PTB17__CAN1_TX	0x31F2
+			>;
+		};
+
 		pinctrl_gpio_ext: gpio_ext {
 			fsl,pins = <
 				VF610_PAD_PTD10__GPIO_89	0x22ed /* EXT_IO_0 */

arch/arm/boot/dts/vf610-colibri.dtsi

@@ -18,8 +18,3 @@ memory {
 		reg = <0x80000000 0x10000000>;
 	};
 };
-
-&L2 {
-	arm,data-latency = <2 1 2>;
-	arm,tag-latency = <3 2 3>;
-};

arch/arm/boot/dts/vf610.dtsi

@@ -19,7 +19,7 @@ L2: l2-cache@40006000 {
 		reg = <0x40006000 0x1000>;
 		cache-unified;
 		cache-level = <2>;
-		arm,data-latency = <1 1 1>;
+		arm,data-latency = <3 3 3>;
 		arm,tag-latency = <2 2 2>;
 	};
 };

arch/arm/boot/dts/vf610m4-cosmic.dts

+/*
+ * Device tree for Cosmic+ VF6xx Cortex-M4 support
+ *
+ * Copyright (C) 2015
+ *
+ * Based on vf610m4 Colibri
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "vf610m4.dtsi"
+
+/ {
+	model = "VF610 Cortex-M4";
+	compatible = "fsl,vf610m4";
+};
+
+&gpio0 {
+	status = "disabled";
+};
+
+&gpio1 {
+	status = "disabled";
+};
+
+&gpio2 {
+	status = "disabled";
+};
+
+&gpio3 {
+	status = "disabled";
+};
+
+&gpio4 {
+	status = "disabled";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&iomuxc {
+	vf610-cosmic {
+		pinctrl_uart3: uart3grp {
+			fsl,pins = <
+				VF610_PAD_PTA20__UART3_TX		0x21a2
+				VF610_PAD_PTA21__UART3_RX		0x21a1
+			>;
+		};
+	};
+};

arch/arm/boot/dts/vfxxx.dtsi

@@ -178,8 +178,10 @@ sai2: sai@40031000 {
 				compatible = "fsl,vf610-sai";
 				reg = <0x40031000 0x1000>;
 				interrupts = <86 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clks VF610_CLK_SAI2>;
-				clock-names = "sai";
+				clocks = <&clks VF610_CLK_SAI2>,
+					<&clks VF610_CLK_SAI2_DIV>,
+					<&clks 0>, <&clks 0>;
+				clock-names = "bus", "mclk1", "mclk2", "mclk3";
 				dma-names = "tx", "rx";
 				dmas = <&edma0 0 21>,
 					<&edma0 0 20>;
@@ -453,6 +455,30 @@ uart5: serial@400aa000 {
 				status = "disabled";
 			};
 
+			dspi2: dspi2@400ac000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,vf610-dspi";
+				reg = <0x400ac000 0x1000>;
+				interrupts = <69 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks VF610_CLK_DSPI2>;
+				clock-names = "dspi";
+				spi-num-chipselects = <2>;
+				status = "disabled";
+			};
+
+			dspi3: dspi3@400ad000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,vf610-dspi";
+				reg = <0x400ad000 0x1000>;
+				interrupts = <70 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks VF610_CLK_DSPI3>;
+				clock-names = "dspi";
+				spi-num-chipselects = <2>;
+				status = "disabled";
+			};
+
 			adc1: adc@400bb000 {
 				compatible = "fsl,vf610-adc";
 				reg = <0x400bb000 0x1000>;

drivers/clk/imx/clk-imx25.c

@@ -96,13 +96,11 @@ static struct clk ** const uart_clks[] __initconst = {
 	NULL
 };
 
-static int __init __mx25_clocks_init(unsigned long osc_rate,
-				     void __iomem *ccm_base)
+static int __init __mx25_clocks_init(void __iomem *ccm_base)
 {
 	BUG_ON(!ccm_base);
 
 	clk[dummy] = imx_clk_fixed("dummy", 0);
-	clk[osc] = imx_clk_fixed("osc", osc_rate);
 	clk[mpll] = imx_clk_pllv1(IMX_PLLV1_IMX25, "mpll", "osc", ccm(CCM_MPCTL));
 	clk[upll] = imx_clk_pllv1(IMX_PLLV1_IMX25, "upll", "osc", ccm(CCM_UPCTL));
 	clk[mpll_cpu_3_4] = imx_clk_fixed_factor("mpll_cpu_3_4", "mpll", 3, 4);
@@ -250,22 +248,10 @@ static int __init __mx25_clocks_init(unsigned long osc_rate,
 
 static void __init mx25_clocks_init_dt(struct device_node *np)
 {
-	struct device_node *refnp;
-	unsigned long osc_rate = 24000000;
 	void __iomem *ccm;
 
-	/* retrieve the freqency of fixed clocks from device tree */
-	for_each_compatible_node(refnp, NULL, "fixed-clock") {
-		u32 rate;
-		if (of_property_read_u32(refnp, "clock-frequency", &rate))
-			continue;
-
-		if (of_device_is_compatible(refnp, "fsl,imx-osc"))
-			osc_rate = rate;
-	}
-
 	ccm = of_iomap(np, 0);
-	__mx25_clocks_init(osc_rate, ccm);
+	__mx25_clocks_init(ccm);
 
 	clk_data.clks = clk;
 	clk_data.clk_num = ARRAY_SIZE(clk);

drivers/clk/imx/clk-imx51-imx53.c

@@ -519,10 +519,10 @@ static void __init mx53_clocks_init(struct device_node *np)
 						mx53_ldb_di0_sel, ARRAY_SIZE(mx53_ldb_di0_sel), CLK_SET_RATE_PARENT);
 	clk[IMX5_CLK_LDB_DI0_GATE]	= imx_clk_gate2("ldb_di0_gate", "ldb_di0_div", MXC_CCM_CCGR6, 28);
 	clk[IMX5_CLK_LDB_DI1_GATE]	= imx_clk_gate2("ldb_di1_gate", "ldb_di1_div", MXC_CCM_CCGR6, 30);
-	clk[IMX5_CLK_IPU_DI0_SEL]	= imx_clk_mux("ipu_di0_sel", MXC_CCM_CSCMR2, 26, 3,
-						mx53_ipu_di0_sel, ARRAY_SIZE(mx53_ipu_di0_sel));
-	clk[IMX5_CLK_IPU_DI1_SEL]	= imx_clk_mux("ipu_di1_sel", MXC_CCM_CSCMR2, 29, 3,
-						mx53_ipu_di1_sel, ARRAY_SIZE(mx53_ipu_di1_sel));
+	clk[IMX5_CLK_IPU_DI0_SEL]	= imx_clk_mux_flags("ipu_di0_sel", MXC_CCM_CSCMR2, 26, 3,
+						mx53_ipu_di0_sel, ARRAY_SIZE(mx53_ipu_di0_sel), CLK_SET_RATE_PARENT);
+	clk[IMX5_CLK_IPU_DI1_SEL]	= imx_clk_mux_flags("ipu_di1_sel", MXC_CCM_CSCMR2, 29, 3,
+						mx53_ipu_di1_sel, ARRAY_SIZE(mx53_ipu_di1_sel), CLK_SET_RATE_PARENT);
 	clk[IMX5_CLK_TVE_EXT_SEL]	= imx_clk_mux_flags("tve_ext_sel", MXC_CCM_CSCMR1, 6, 1,
 						mx53_tve_ext_sel, ARRAY_SIZE(mx53_tve_ext_sel), CLK_SET_RATE_PARENT);
 	clk[IMX5_CLK_TVE_GATE]		= imx_clk_gate2("tve_gate", "tve_pred", MXC_CCM_CCGR2, 30);

drivers/clk/imx/clk-imx6q.c

@@ -70,7 +70,8 @@ static const char *cko_sels[] = { "cko1", "cko2", };
 static const char *lvds_sels[] = {
 	"dummy", "dummy", "dummy", "dummy", "dummy", "dummy",
 	"pll4_audio", "pll5_video", "pll8_mlb", "enet_ref",
-	"pcie_ref_125m", "sata_ref_100m",
+	"pcie_ref_125m", "sata_ref_100m",  "usbphy1", "usbphy2",
+	"dummy", "dummy", "dummy", "dummy", "osc",
 };
 static const char *pll_bypass_src_sels[] = { "osc", "lvds1_in", "lvds2_in", "dummy", };
 static const char *pll1_bypass_sels[] = { "pll1", "pll1_bypass_src", };

drivers/clk/imx/clk-imx6ul.c

@@ -399,9 +399,7 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
 	/* mask handshake of mmdc */
 	writel_relaxed(BM_CCM_CCDR_MMDC_CH0_MASK, base + CCDR);
 
-	for (i = 0; i < ARRAY_SIZE(clks); i++)
-		if (IS_ERR(clks[i]))
-			pr_err("i.MX6UL clk %d: register failed with %ld\n", i, PTR_ERR(clks[i]));
+	imx_check_clocks(clks, ARRAY_SIZE(clks));
 
 	clk_data.clks = clks;
 	clk_data.clk_num = ARRAY_SIZE(clks);

drivers/clk/imx/clk-imx7d.c

@@ -833,10 +833,13 @@ static void __init imx7d_clocks_init(struct device_node *ccm_node)
 
 	clks[IMX7D_GPT_3M_CLK] = imx_clk_fixed_factor("gpt_3m", "osc", 1, 8);
 
-	for (i = 0; i < ARRAY_SIZE(clks); i++)
-		if (IS_ERR(clks[i]))
-			pr_err("i.MX7D clk %d: register failed with %ld\n",
-					i, PTR_ERR(clks[i]));
+	clks[IMX7D_CLK_ARM] = imx_clk_cpu("arm", "arm_a7_root_clk",
+					 clks[IMX7D_ARM_A7_ROOT_CLK],
+					 clks[IMX7D_ARM_A7_ROOT_SRC],
+					 clks[IMX7D_PLL_ARM_MAIN_CLK],
+					 clks[IMX7D_PLL_SYS_MAIN_CLK]);
+
+	imx_check_clocks(clks, ARRAY_SIZE(clks));
 
 	clk_data.clks = clks;
 	clk_data.clk_num = ARRAY_SIZE(clks);

drivers/clk/imx/clk-pllv3.c

@@ -97,6 +97,16 @@ static void clk_pllv3_unprepare(struct clk_hw *hw)
 	writel_relaxed(val, pll->base);
 }
 
+static int clk_pllv3_is_prepared(struct clk_hw *hw)
+{
+	struct clk_pllv3 *pll = to_clk_pllv3(hw);
+
+	if (readl_relaxed(pll->base) & BM_PLL_LOCK)
+		return 1;
+
+	return 0;
+}
+
 static unsigned long clk_pllv3_recalc_rate(struct clk_hw *hw,
 					   unsigned long parent_rate)
 {
@@ -139,6 +149,7 @@ static int clk_pllv3_set_rate(struct clk_hw *hw, unsigned long rate,
 static const struct clk_ops clk_pllv3_ops = {
 	.prepare	= clk_pllv3_prepare,
 	.unprepare	= clk_pllv3_unprepare,
+	.is_prepared	= clk_pllv3_is_prepared,
 	.recalc_rate	= clk_pllv3_recalc_rate,
 	.round_rate	= clk_pllv3_round_rate,
 	.set_rate	= clk_pllv3_set_rate,
@@ -193,6 +204,7 @@ static int clk_pllv3_sys_set_rate(struct clk_hw *hw, unsigned long rate,
 static const struct clk_ops clk_pllv3_sys_ops = {
 	.prepare	= clk_pllv3_prepare,
 	.unprepare	= clk_pllv3_unprepare,
+	.is_prepared	= clk_pllv3_is_prepared,
 	.recalc_rate	= clk_pllv3_sys_recalc_rate,
 	.round_rate	= clk_pllv3_sys_round_rate,
 	.set_rate	= clk_pllv3_sys_set_rate,
@@ -265,6 +277,7 @@ static int clk_pllv3_av_set_rate(struct clk_hw *hw, unsigned long rate,
 static const struct clk_ops clk_pllv3_av_ops = {
 	.prepare	= clk_pllv3_prepare,
 	.unprepare	= clk_pllv3_unprepare,
+	.is_prepared	= clk_pllv3_is_prepared,
 	.recalc_rate	= clk_pllv3_av_recalc_rate,
 	.round_rate	= clk_pllv3_av_round_rate,
 	.set_rate	= clk_pllv3_av_set_rate,
@@ -279,6 +292,7 @@ static unsigned long clk_pllv3_enet_recalc_rate(struct clk_hw *hw,
 static const struct clk_ops clk_pllv3_enet_ops = {
 	.prepare	= clk_pllv3_prepare,
 	.unprepare	= clk_pllv3_unprepare,
+	.is_prepared	= clk_pllv3_is_prepared,
 	.recalc_rate	= clk_pllv3_enet_recalc_rate,
 };
 

drivers/clk/imx/clk-vf610.c

@@ -335,22 +335,22 @@ static void __init vf610_clocks_init(struct device_node *ccm_node)
 	clk[VF610_CLK_SAI0_SEL] = imx_clk_mux("sai0_sel", CCM_CSCMR1, 0, 2, sai_sels, 4);
 	clk[VF610_CLK_SAI0_EN] = imx_clk_gate("sai0_en", "sai0_sel", CCM_CSCDR1, 16);
 	clk[VF610_CLK_SAI0_DIV] = imx_clk_divider("sai0_div", "sai0_en", CCM_CSCDR1, 0, 4);
-	clk[VF610_CLK_SAI0] = imx_clk_gate2("sai0", "sai0_div", CCM_CCGR0, CCM_CCGRx_CGn(15));
+	clk[VF610_CLK_SAI0] = imx_clk_gate2("sai0", "ipg_bus", CCM_CCGR0, CCM_CCGRx_CGn(15));
 
 	clk[VF610_CLK_SAI1_SEL] = imx_clk_mux("sai1_sel", CCM_CSCMR1, 2, 2, sai_sels, 4);
 	clk[VF610_CLK_SAI1_EN] = imx_clk_gate("sai1_en", "sai1_sel", CCM_CSCDR1, 17);
 	clk[VF610_CLK_SAI1_DIV] = imx_clk_divider("sai1_div", "sai1_en", CCM_CSCDR1, 4, 4);
-	clk[VF610_CLK_SAI1] = imx_clk_gate2("sai1", "sai1_div", CCM_CCGR1, CCM_CCGRx_CGn(0));
+	clk[VF610_CLK_SAI1] = imx_clk_gate2("sai1", "ipg_bus", CCM_CCGR1, CCM_CCGRx_CGn(0));
 
 	clk[VF610_CLK_SAI2_SEL] = imx_clk_mux("sai2_sel", CCM_CSCMR1, 4, 2, sai_sels, 4);
 	clk[VF610_CLK_SAI2_EN] = imx_clk_gate("sai2_en", "sai2_sel", CCM_CSCDR1, 18);
 	clk[VF610_CLK_SAI2_DIV] = imx_clk_divider("sai2_div", "sai2_en", CCM_CSCDR1, 8, 4);
-	clk[VF610_CLK_SAI2] = imx_clk_gate2("sai2", "sai2_div", CCM_CCGR1, CCM_CCGRx_CGn(1));
+	clk[VF610_CLK_SAI2] = imx_clk_gate2("sai2", "ipg_bus", CCM_CCGR1, CCM_CCGRx_CGn(1));
 
 	clk[VF610_CLK_SAI3_SEL] = imx_clk_mux("sai3_sel", CCM_CSCMR1, 6, 2, sai_sels, 4);
 	clk[VF610_CLK_SAI3_EN] = imx_clk_gate("sai3_en", "sai3_sel", CCM_CSCDR1, 19);
 	clk[VF610_CLK_SAI3_DIV] = imx_clk_divider("sai3_div", "sai3_en", CCM_CSCDR1, 12, 4);
-	clk[VF610_CLK_SAI3] = imx_clk_gate2("sai3", "sai3_div", CCM_CCGR1, CCM_CCGRx_CGn(2));
+	clk[VF610_CLK_SAI3] = imx_clk_gate2("sai3", "ipg_bus", CCM_CCGR1, CCM_CCGRx_CGn(2));
 
 	clk[VF610_CLK_NFC_SEL] = imx_clk_mux("nfc_sel", CCM_CSCMR1, 12, 2, nfc_sels, 4);
 	clk[VF610_CLK_NFC_EN] = imx_clk_gate("nfc_en", "nfc_sel", CCM_CSCDR2, 9);

include/dt-bindings/clock/imx7d-clock.h

@@ -447,5 +447,6 @@
 #define IMX7D_SEMA4_HS_ROOT_CLK		434
 #define IMX7D_PLL_DRAM_TEST_DIV		435
 #define IMX7D_ADC_ROOT_CLK		436
-#define IMX7D_CLK_END			437
+#define IMX7D_CLK_ARM			437
+#define IMX7D_CLK_END			438
 #endif /* __DT_BINDINGS_CLOCK_IMX7D_H */