Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (59 commits)
  HID: fix up 'EMBEDDED' mess in Kconfig
  HID: roccat: cleanup preprocessor macros
  HID: roccat: refactor special event handling
  HID: roccat: fix special button support
  HID: roccat: Correctly mark init and exit functions
  HID: hidraw: Use Interrupt Endpoint for OUT Transfers if Available
  HID: hid-samsung: remove redundant key mappings
  HID: add omitted hid-zydacron.c file
  HID: hid-samsung: add support for Creative Desktop Wireless 6000
  HID: picolcd: Eliminate use after free
  HID: Zydacron Remote Control driver
  HID: Use kmemdup
  HID: magicmouse: fix input registration
  HID: make Prodikeys driver standalone config option
  HID: Prodikeys PC-MIDI HID Driver
  HID: hidraw: fix indentation
  HID: ntrig: add filtering module parameters
  HID: ntrig: add sysfs access to filter parameters
  HID: ntrig: add sensitivity and responsiveness support
  HID: add multi-input quirk for eGalax Touchcontroller
  ...

Documentation/ABI/testing/sysfs-driver-hid-picolcd

+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/operation_mode
+Date:		March 2010
+Contact:	Bruno Prémont <bonbons@linux-vserver.org>
+Description:	Make it possible to switch the PicoLCD device between LCD
+		(firmware) and bootloader (flasher) operation modes.
+
+		Reading: returns list of available modes, the active mode being
+		enclosed in brackets ('[' and ']')
+
+		Writing: causes operation mode switch. Permitted values are
+		the non-active mode names listed when read.
+
+		Note: when switching mode the current PicoLCD HID device gets
+		disconnected and reconnects after above delay (see attribute
+		operation_mode_delay for its value).
+
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/operation_mode_delay
+Date:		April 2010
+Contact:	Bruno Prémont <bonbons@linux-vserver.org>
+Description:	Delay PicoLCD waits before restarting in new mode when
+		operation_mode has changed.
+
+		Reading/Writing: It is expressed in ms and permitted range is
+		0..30000ms.
+
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/fb_update_rate
+Date:		March 2010
+Contact:	Bruno Prémont <bonbons@linux-vserver.org>
+Description:	Make it possible to adjust defio refresh rate.
+
+		Reading: returns list of available refresh rates (expressed in Hz),
+		the active refresh rate being enclosed in brackets ('[' and ']')
+
+		Writing: accepts new refresh rate expressed in integer Hz
+		within permitted rates.
+
+		Note: As device can barely do 2 complete refreshes a second
+		it only makes sense to adjust this value if only one or two
+		tiles get changed and it's not appropriate to expect the application
+		to flush it's tiny changes explicitely at higher than default rate.
+

Documentation/ABI/testing/sysfs-driver-hid-prodikeys

+What:		/sys/bus/hid/drivers/prodikeys/.../channel
+Date:		April 2010
+KernelVersion:	2.6.34
+Contact:	Don Prince <dhprince.devel@yahoo.co.uk>
+Description:
+		Allows control (via software) the midi channel to which
+		that the pc-midi keyboard will output.midi data.
+		Range: 0..15
+		Type:  Read/write
+What:		/sys/bus/hid/drivers/prodikeys/.../sustain
+Date:		April 2010
+KernelVersion:	2.6.34
+Contact:	Don Prince <dhprince.devel@yahoo.co.uk>
+Description:
+		Allows control (via software) the sustain duration of a
+		note held by the pc-midi driver.
+		0 means sustain mode is disabled.
+		Range: 0..5000 (milliseconds)
+		Type:  Read/write
+What:		/sys/bus/hid/drivers/prodikeys/.../octave
+Date:		April 2010
+KernelVersion:	2.6.34
+Contact:	Don Prince <dhprince.devel@yahoo.co.uk>
+Description:
+		Controls the octave shift modifier in the pc-midi driver.
+		The octave can be shifted via software up/down 2 octaves.
+		0 means the no ocatve shift.
+		Range: -2..2 (minus 2 to plus 2)
+		Type: Read/Write

Documentation/ABI/testing/sysfs-driver-hid-roccat-kone

+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/actual_dpi
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	It is possible to switch the dpi setting of the mouse with the
+		press of a button.
+		When read, this file returns the raw number of the actual dpi
+		setting reported by the mouse. This number has to be further
+		processed to receive the real dpi value.
+
+		VALUE DPI
+		1     800
+		2     1200
+		3     1600
+		4     2000
+		5     2400
+		6     3200
+
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/actual_profile
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the number of the actual profile.
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/firmware_version
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the raw integer version number of the
+		firmware reported by the mouse. Using the integer value eases
+		further usage in other programs. To receive the real version
+		number the decimal point has to be shifted 2 positions to the
+		left. E.g. a returned value of 138 means 1.38
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/kone_driver_version
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the driver version.
+		The format of the string is "v<major>.<minor>.<patchlevel>".
+		This attribute is used by the userland tools to find the sysfs-
+		paths of installed kone-mice and determine the capabilites of
+		the driver. Versions of this driver for old kernels replace
+		usbhid instead of generic-usb. The way to scan for this file
+		has been chosen to provide a consistent way for all supported
+		kernel versions.
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/profile[1-5]
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The mouse can store 5 profiles which can be switched by the
+                press of a button. A profile holds informations like button
+                mappings, sensitivity, the colors of the 5 leds and light
+                effects.
+                When read, these files return the respective profile. The
+                returned data is 975 bytes in size.
+		When written, this file lets one write the respective profile
+		data back to the mouse. The data has to be 975 bytes long.
+		The mouse will reject invalid data, whereas the profile number
+		stored in the profile doesn't need to fit the number of the
+		store.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/settings
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the settings stored in the mouse.
+		The size of the data is 36 bytes and holds information like the
+		startup_profile, tcu state and calibration_data.
+		When written, this file lets write settings back to the mouse.
+		The data has to be 36 bytes long. The mouse will reject invalid
+		data.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/startup_profile
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The integer value of this attribute ranges from 1 to 5.
+                When read, this attribute returns the number of the profile
+                that's active when the mouse is powered on.
+		When written, this file sets the number of the startup profile
+		and the mouse activates this profile immediately.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/tcu
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The mouse has a "Tracking Control Unit" which lets the user
+		calibrate the laser power to fit the mousepad surface.
+		When read, this file returns the current state of the TCU,
+		where 0 means off and 1 means on.
+		Writing 0 in this file will switch the TCU off.
+		Writing 1 in this file will start the calibration which takes
+		around 6 seconds to complete and activates the TCU.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/weight
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The mouse can be equipped with one of four supplied weights
+		ranging from 5 to 20 grams which are recognized by the mouse
+		and its value can be read out. When read, this file returns the
+		raw value returned by the mouse which eases further processing
+		in other software.
+		The values map to the weights as follows:
+
+		VALUE WEIGHT
+		0     none
+		1     5g
+		2     10g
+		3     15g
+		4     20g
+
+		This file is readonly.

Documentation/ABI/testing/sysfs-wacom

+What:		/sys/class/hidraw/hidraw*/device/speed
+Date:		April 2010
+Kernel Version:	2.6.35
+Contact:	linux-bluetooth@vger.kernel.org
+Description:
+		The /sys/class/hidraw/hidraw*/device/speed file controls
+		reporting speed of wacom bluetooth tablet. Reading from
+		this file returns 1 if tablet reports in high speed mode
+		or 0 otherwise. Writing to this file one of these values
+		switches reporting speed.

drivers/hid/Kconfig

@@ -86,6 +86,12 @@ config HID_BELKIN
 	---help---
 	Support for Belkin Flip KVM and Wireless keyboard.
 
+config HID_CANDO
+	tristate "Cando dual touch panel"
+	depends on USB_HID
+	---help---
+	Support for Cando dual touch panel.
+
 config HID_CHERRY
 	tristate "Cherry" if EMBEDDED
 	depends on USB_HID
@@ -100,6 +106,21 @@ config HID_CHICONY
 	---help---
 	Support for Chicony Tactical pad.
 
+config HID_PRODIKEYS
+	tristate "Prodikeys PC-MIDI Keyboard support"
+	depends on USB_HID && SND
+	select SND_RAWMIDI
+	---help---
+	Support for Prodikeys PC-MIDI Keyboard device support.
+	Say Y here to enable support for this device.
+	- Prodikeys PC-MIDI keyboard.
+	  The Prodikeys PC-MIDI acts as a USB Audio device, with one MIDI
+	  input and one MIDI output. These MIDI jacks appear as
+	  a sound "card" in the ALSA sound system.
+	  Note: if you say N here, this device will still function as a basic
+	  multimedia keyboard, but will lack support for the musical keyboard
+	  and some additional multimedia keys.
+
 config HID_CYPRESS
 	tristate "Cypress" if EMBEDDED
 	depends on USB_HID
@@ -108,9 +129,8 @@ config HID_CYPRESS
 	Support for cypress mouse and barcode readers.
 
 config HID_DRAGONRISE
-	tristate "DragonRise Inc. support" if EMBEDDED
+	tristate "DragonRise Inc. support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Say Y here if you have DragonRise Inc.game controllers.
 
@@ -122,6 +142,12 @@ config DRAGONRISE_FF
 	Say Y here if you want to enable force feedback support for DragonRise Inc.
 	game controllers.
 
+config HID_EGALAX
+	tristate "eGalax multi-touch panel"
+	depends on USB_HID
+	---help---
+	Support for the eGalax dual-touch panel.
+
 config HID_EZKEY
 	tristate "Ezkey" if EMBEDDED
 	depends on USB_HID
@@ -137,16 +163,14 @@ config HID_KYE
 	Support for Kye/Genius Ergo Mouse.
 
 config HID_GYRATION
-	tristate "Gyration" if EMBEDDED
+	tristate "Gyration"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for Gyration remote control.
 
 config HID_TWINHAN
-	tristate "Twinhan" if EMBEDDED
+	tristate "Twinhan"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for Twinhan IR remote control.
 
@@ -233,16 +257,14 @@ config HID_NTRIG
 	Support for N-Trig touch screen.
 
 config HID_ORTEK
-	tristate "Ortek" if EMBEDDED
+	tristate "Ortek"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for Ortek WKB-2000 wireless keyboard + mouse trackpad.
 
 config HID_PANTHERLORD
-	tristate "Pantherlord support" if EMBEDDED
+	tristate "Pantherlord support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	  Say Y here if you have a PantherLord/GreenAsia based game controller
 	  or adapter.
@@ -256,29 +278,90 @@ config PANTHERLORD_FF
 	  or adapter and want to enable force feedback support for it.
 
 config HID_PETALYNX
-	tristate "Petalynx" if EMBEDDED
+	tristate "Petalynx"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for Petalynx Maxter remote control.
 
+config HID_PICOLCD
+	tristate "PicoLCD (graphic version)"
+	depends on USB_HID
+	---help---
+	  This provides support for Minibox PicoLCD devices, currently
+	  only the graphical ones are supported.
+
+	  This includes support for the following device features:
+	  - Keypad
+	  - Switching between Firmware and Flash mode
+	  - EEProm / Flash access     (via debugfs)
+	  Features selectively enabled:
+	  - Framebuffer for monochrome 256x64 display
+	  - Backlight control
+	  - Contrast control
+	  - General purpose outputs
+	  Features that are not (yet) supported:
+	  - IR
+
+config HID_PICOLCD_FB
+	bool "Framebuffer support" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=FB || FB=y
+	select FB_DEFERRED_IO
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	---help---
+	  Provide access to PicoLCD's 256x64 monochrome display via a
+	  frambuffer device.
+
+config HID_PICOLCD_BACKLIGHT
+	bool "Backlight control" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=BACKLIGHT_CLASS_DEVICE || BACKLIGHT_CLASS_DEVICE=y
+	---help---
+	  Provide access to PicoLCD's backlight control via backlight
+	  class.
+
+config HID_PICOLCD_LCD
+	bool "Contrast control" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=LCD_CLASS_DEVICE || LCD_CLASS_DEVICE=y
+	---help---
+	  Provide access to PicoLCD's LCD contrast via lcd class.
+
+config HID_PICOLCD_LEDS
+	bool "GPO via leds class" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=LEDS_CLASS || LEDS_CLASS=y
+	---help---
+	  Provide access to PicoLCD's GPO pins via leds class.
+
 config HID_QUANTA
 	tristate "Quanta Optical Touch"
 	depends on USB_HID
 	---help---
 	Support for Quanta Optical Touch dual-touch panels.
 
+config HID_ROCCAT_KONE
+	tristate "Roccat Kone Mouse support"
+	depends on USB_HID
+	---help---
+	Support for Roccat Kone mouse.
+
 config HID_SAMSUNG
-	tristate "Samsung" if EMBEDDED
+	tristate "Samsung"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
-	Support for Samsung InfraRed remote control.
+	Support for Samsung InfraRed remote control or keyboards.
 
 config HID_SONY
-	tristate "Sony" if EMBEDDED
+	tristate "Sony"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for Sony PS3 controller.
 
@@ -289,16 +372,14 @@ config HID_STANTUM
 	Support for Stantum multitouch panel.
 
 config HID_SUNPLUS
-	tristate "Sunplus" if EMBEDDED
+	tristate "Sunplus"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for Sunplus wireless desktop.
 
 config HID_GREENASIA
-	tristate "GreenAsia (Product ID 0x12) support" if EMBEDDED
+	tristate "GreenAsia (Product ID 0x12) support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	  Say Y here if you have a GreenAsia (Product ID 0x12) based game
 	  controller or adapter.
@@ -313,9 +394,8 @@ config GREENASIA_FF
 	and want to enable force feedback support for it.
 
 config HID_SMARTJOYPLUS
-	tristate "SmartJoy PLUS PS2/USB adapter support" if EMBEDDED
+	tristate "SmartJoy PLUS PS2/USB adapter support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for SmartJoy PLUS PS2/USB adapter.
 
@@ -328,16 +408,14 @@ config SMARTJOYPLUS_FF
 	enable force feedback support for it.
 
 config HID_TOPSEED
-	tristate "TopSeed Cyberlink remote control support" if EMBEDDED
+	tristate "TopSeed Cyberlink remote control support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
-	Say Y if you have a TopSeed Cyberlink remote control.
+	Say Y if you have a TopSeed Cyberlink or BTC Emprex remote control.
 
 config HID_THRUSTMASTER
-	tristate "ThrustMaster devices support" if EMBEDDED
+	tristate "ThrustMaster devices support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	  Say Y here if you have a THRUSTMASTER FireStore Dual Power 2 or
 	  a THRUSTMASTER Ferrari GT Rumble Wheel.
@@ -357,10 +435,17 @@ config HID_WACOM
 	---help---
 	Support for Wacom Graphire Bluetooth tablet.
 
+config HID_WACOM_POWER_SUPPLY
+	bool "Wacom Bluetooth devices power supply status support"
+	depends on HID_WACOM
+	select POWER_SUPPLY
+	---help---
+	  Say Y here if you want to enable power supply status monitoring for
+	  Wacom Bluetooth devices.
+
 config HID_ZEROPLUS
-	tristate "Zeroplus based game controller support" if EMBEDDED
+	tristate "Zeroplus based game controller support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	  Say Y here if you have a Zeroplus based game controller.
 
@@ -372,6 +457,12 @@ config ZEROPLUS_FF
 	  Say Y here if you have a Zeroplus based game controller and want
 	  to have force feedback support for it.
 
+config HID_ZYDACRON
+	tristate "Zydacron remote control support"
+	depends on USB_HID
+	---help---
+	Support for Zydacron remote control.
+
 endmenu
 
 endif # HID_SUPPORT

drivers/hid/Makefile

@@ -26,10 +26,12 @@ obj-$(CONFIG_HID_3M_PCT)	+= hid-3m-pct.o
 obj-$(CONFIG_HID_A4TECH)	+= hid-a4tech.o
 obj-$(CONFIG_HID_APPLE)		+= hid-apple.o
 obj-$(CONFIG_HID_BELKIN)	+= hid-belkin.o
+obj-$(CONFIG_HID_CANDO)		+= hid-cando.o
 obj-$(CONFIG_HID_CHERRY)	+= hid-cherry.o
 obj-$(CONFIG_HID_CHICONY)	+= hid-chicony.o
 obj-$(CONFIG_HID_CYPRESS)	+= hid-cypress.o
 obj-$(CONFIG_HID_DRAGONRISE)	+= hid-drff.o
+obj-$(CONFIG_HID_EGALAX)	+= hid-egalax.o
 obj-$(CONFIG_HID_EZKEY)		+= hid-ezkey.o
 obj-$(CONFIG_HID_GYRATION)	+= hid-gyration.o
 obj-$(CONFIG_HID_KENSINGTON)	+= hid-kensington.o
@@ -41,9 +43,12 @@ obj-$(CONFIG_HID_MONTEREY)	+= hid-monterey.o
 obj-$(CONFIG_HID_MOSART)	+= hid-mosart.o
 obj-$(CONFIG_HID_NTRIG)		+= hid-ntrig.o
 obj-$(CONFIG_HID_ORTEK)		+= hid-ortek.o
+obj-$(CONFIG_HID_PRODIKEYS)	+= hid-prodikeys.o
 obj-$(CONFIG_HID_QUANTA)	+= hid-quanta.o
 obj-$(CONFIG_HID_PANTHERLORD)	+= hid-pl.o
 obj-$(CONFIG_HID_PETALYNX)	+= hid-petalynx.o
+obj-$(CONFIG_HID_PICOLCD)	+= hid-picolcd.o
+obj-$(CONFIG_HID_ROCCAT_KONE)	+= hid-roccat-kone.o
 obj-$(CONFIG_HID_SAMSUNG)	+= hid-samsung.o
 obj-$(CONFIG_HID_SMARTJOYPLUS)	+= hid-sjoy.o
 obj-$(CONFIG_HID_SONY)		+= hid-sony.o
@@ -54,6 +59,7 @@ obj-$(CONFIG_HID_THRUSTMASTER)	+= hid-tmff.o
 obj-$(CONFIG_HID_TOPSEED)	+= hid-topseed.o
 obj-$(CONFIG_HID_TWINHAN)	+= hid-twinhan.o
 obj-$(CONFIG_HID_ZEROPLUS)	+= hid-zpff.o
+obj-$(CONFIG_HID_ZYDACRON)	+= hid-zydacron.o
 obj-$(CONFIG_HID_WACOM)		+= hid-wacom.o
 
 obj-$(CONFIG_USB_HID)		+= usbhid/

drivers/hid/hid-3m-pct.c

 /*
  *  HID driver for 3M PCT multitouch panels
  *
- *  Copyright (c) 2009 Stephane Chatty <chatty@enac.fr>
+ *  Copyright (c) 2009-2010 Stephane Chatty <chatty@enac.fr>
  *
  */
 
@@ -25,7 +25,7 @@ MODULE_LICENSE("GPL");
 #include "hid-ids.h"
 
 struct mmm_finger {
-	__s32 x, y;
+	__s32 x, y, w, h;
 	__u8 rank;
 	bool touch, valid;
 };
@@ -82,7 +82,18 @@ static int mmm_input_mapping(struct hid_device *hdev, struct hid_input *hi,
 			/* touchscreen emulation */
 			hid_map_usage(hi, usage, bit, max, EV_KEY, BTN_TOUCH);
 			return 1;
+		case HID_DG_WIDTH:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_TOUCH_MAJOR);
+			return 1;
+		case HID_DG_HEIGHT:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_TOUCH_MINOR);
+			input_set_abs_params(hi->input, ABS_MT_ORIENTATION,
+					1, 1, 0, 0);
+			return 1;
 		case HID_DG_CONTACTID:
+			field->logical_maximum = 59;
 			hid_map_usage(hi, usage, bit, max,
 					EV_ABS, ABS_MT_TRACKING_ID);
 			return 1;
@@ -128,9 +139,15 @@ static void mmm_filter_event(struct mmm_data *md, struct input_dev *input)
 			/* this finger is just placeholder data, ignore */
 		} else if (f->touch) {
 			/* this finger is on the screen */
+			int wide = (f->w > f->h);
 			input_event(input, EV_ABS, ABS_MT_TRACKING_ID, i);
 			input_event(input, EV_ABS, ABS_MT_POSITION_X, f->x);
 			input_event(input, EV_ABS, ABS_MT_POSITION_Y, f->y);
+			input_event(input, EV_ABS, ABS_MT_ORIENTATION, wide);
+			input_event(input, EV_ABS, ABS_MT_TOUCH_MAJOR,
+						wide ? f->w : f->h);
+			input_event(input, EV_ABS, ABS_MT_TOUCH_MINOR,
+						wide ? f->h : f->w);
 			input_mt_sync(input);
 			/*
 			 * touchscreen emulation: maintain the age rank
@@ -197,6 +214,14 @@ static int mmm_event(struct hid_device *hid, struct hid_field *field,
 		case HID_DG_CONFIDENCE:
 			md->valid = value;
 			break;
+		case HID_DG_WIDTH:
+			if (md->valid)
+				md->f[md->curid].w = value;
+			break;
+		case HID_DG_HEIGHT:
+			if (md->valid)
+				md->f[md->curid].h = value;
+			break;
 		case HID_DG_CONTACTID:
 			if (md->valid) {
 				md->curid = value;
@@ -255,6 +280,7 @@ static void mmm_remove(struct hid_device *hdev)
 
 static const struct hid_device_id mmm_devices[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_3M, USB_DEVICE_ID_3M1968) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_3M, USB_DEVICE_ID_3M2256) },
 	{ }
 };
 MODULE_DEVICE_TABLE(hid, mmm_devices);
@@ -287,5 +313,4 @@ static void __exit mmm_exit(void)
 
 module_init(mmm_init);
 module_exit(mmm_exit);
-MODULE_LICENSE("GPL");
 

drivers/hid/hid-cando.c

+/*
+ *  HID driver for Cando dual-touch panels
+ *
+ *  Copyright (c) 2010 Stephane Chatty <chatty@enac.fr>
+ *
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <linux/device.h>
+#include <linux/hid.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+
+MODULE_AUTHOR("Stephane Chatty <chatty@enac.fr>");
+MODULE_DESCRIPTION("Cando dual-touch panel");
+MODULE_LICENSE("GPL");
+
+#include "hid-ids.h"
+
+struct cando_data {
+	__u16 x, y;
+	__u8 id;
+	__s8 oldest;		/* id of the oldest finger in previous frame */
+	bool valid;		/* valid finger data, or just placeholder? */
+	bool first;		/* is this the first finger in this frame? */
+	__s8 firstid;		/* id of the first finger in the frame */
+	__u16 firstx, firsty;	/* (x, y) of the first finger in the frame */
+};
+
+static int cando_input_mapping(struct hid_device *hdev, struct hid_input *hi,
+		struct hid_field *field, struct hid_usage *usage,
+		unsigned long **bit, int *max)
+{
+	switch (usage->hid & HID_USAGE_PAGE) {
+
+	case HID_UP_GENDESK:
+		switch (usage->hid) {
+		case HID_GD_X:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_POSITION_X);
+			/* touchscreen emulation */
+			input_set_abs_params(hi->input, ABS_X,
+						field->logical_minimum,
+						field->logical_maximum, 0, 0);
+			return 1;
+		case HID_GD_Y:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_POSITION_Y);
+			/* touchscreen emulation */
+			input_set_abs_params(hi->input, ABS_Y,
+						field->logical_minimum,
+						field->logical_maximum, 0, 0);
+			return 1;
+		}
+		return 0;
+
+	case HID_UP_DIGITIZER:
+		switch (usage->hid) {
+		case HID_DG_TIPSWITCH:
+		case HID_DG_CONTACTMAX:
+			return -1;
+		case HID_DG_INRANGE:
+			/* touchscreen emulation */
+			hid_map_usage(hi, usage, bit, max, EV_KEY, BTN_TOUCH);
+			return 1;
+		case HID_DG_CONTACTID:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_TRACKING_ID);
+			return 1;
+		}
+		return 0;
+	}
+
+	return 0;
+}
+
+static int cando_input_mapped(struct hid_device *hdev, struct hid_input *hi,
+		struct hid_field *field, struct hid_usage *usage,
+		unsigned long **bit, int *max)
+{
+	if (usage->type == EV_KEY || usage->type == EV_ABS)
+		clear_bit(usage->code, *bit);
+
+	return 0;
+}
+
+/*
+ * this function is called when a whole finger has been parsed,
+ * so that it can decide what to send to the input layer.
+ */
+static void cando_filter_event(struct cando_data *td, struct input_dev *input)
+{
+	td->first = !td->first; /* touchscreen emulation */
+
+	if (!td->valid) {
+		/*
+		 * touchscreen emulation: if this is the second finger and
+		 * the first was valid, the first was the oldest; if the
+		 * first was not valid and there was a valid finger in the
+		 * previous frame, this is a release.
+		 */
+		if (td->first) {
+			td->firstid = -1;
+		} else if (td->firstid >= 0) {
+			input_event(input, EV_ABS, ABS_X, td->firstx);
+			input_event(input, EV_ABS, ABS_Y, td->firsty);
+			td->oldest = td->firstid;
+		} else if (td->oldest >= 0) {
+			input_event(input, EV_KEY, BTN_TOUCH, 0);
+			td->oldest = -1;
+		}
+
+		return;
+	}
+	
+	input_event(input, EV_ABS, ABS_MT_TRACKING_ID, td->id);
+	input_event(input, EV_ABS, ABS_MT_POSITION_X, td->x);
+	input_event(input, EV_ABS, ABS_MT_POSITION_Y, td->y);
+
+	input_mt_sync(input);
+
+	/*
+	 * touchscreen emulation: if there was no touching finger previously,
+	 * emit touch event
+	 */
+	if (td->oldest < 0) {
+		input_event(input, EV_KEY, BTN_TOUCH, 1);
+		td->oldest = td->id;
+	}
+
+	/*
+	 * touchscreen emulation: if this is the first finger, wait for the
+	 * second; the oldest is then the second if it was the oldest already
+	 * or if there was no first, the first otherwise.
+	 */
+	if (td->first) {
+		td->firstx = td->x;
+		td->firsty = td->y;
+		td->firstid = td->id;
+	} else {
+		int x, y, oldest;
+		if (td->id == td->oldest || td->firstid < 0) {
+			x = td->x;
+			y = td->y;
+			oldest = td->id;
+		} else {
+			x = td->firstx;
+			y = td->firsty;
+			oldest = td->firstid;
+		}
+		input_event(input, EV_ABS, ABS_X, x);
+		input_event(input, EV_ABS, ABS_Y, y);
+		td->oldest = oldest;
+	}
+}
+
+
+static int cando_event(struct hid_device *hid, struct hid_field *field,
+				struct hid_usage *usage, __s32 value)
+{
+	struct cando_data *td = hid_get_drvdata(hid);
+
+	if (hid->claimed & HID_CLAIMED_INPUT) {
+		struct input_dev *input = field->hidinput->input;
+
+		switch (usage->hid) {
+		case HID_DG_INRANGE:
+			td->valid = value;
+			break;
+		case HID_DG_CONTACTID:
+			td->id = value;
+			break;
+		case HID_GD_X:
+			td->x = value;
+			break;
+		case HID_GD_Y:
+			td->y = value;
+			cando_filter_event(td, input);
+			break;
+		case HID_DG_TIPSWITCH:
+			/* avoid interference from generic hidinput handling */
+			break;
+
+		default:
+			/* fallback to the generic hidinput handling */
+			return 0;
+		}
+	}
+
+	/* we have handled the hidinput part, now remains hiddev */
+	if (hid->claimed & HID_CLAIMED_HIDDEV && hid->hiddev_hid_event)
+		hid->hiddev_hid_event(hid, field, usage, value);
+
+	return 1;
+}
+
+static int cando_probe(struct hid_device *hdev, const struct hid_device_id *id)
+{
+	int ret;
+	struct cando_data *td;
+
+	td = kmalloc(sizeof(struct cando_data), GFP_KERNEL);
+	if (!td) {
+		dev_err(&hdev->dev, "cannot allocate Cando Touch data\n");
+		return -ENOMEM;
+	}
+	hid_set_drvdata(hdev, td);
+	td->first = false;
+	td->oldest = -1;
+	td->valid = false;
+
+	ret = hid_parse(hdev);
+	if (!ret)
+		ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
+
+	if (ret)
+		kfree(td);
+
+	return ret;
+}
+
+static void cando_remove(struct hid_device *hdev)
+{
+	hid_hw_stop(hdev);
+	kfree(hid_get_drvdata(hdev));
+	hid_set_drvdata(hdev, NULL);
+}
+
+static const struct hid_device_id cando_devices[] = {
+	{ HID_USB_DEVICE(USB_VENDOR_ID_CANDO,
+			USB_DEVICE_ID_CANDO_MULTI_TOUCH) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_CANDO,
+			USB_DEVICE_ID_CANDO_MULTI_TOUCH_11_6) },
+	{ }
+};
+MODULE_DEVICE_TABLE(hid, cando_devices);
+
+static const struct hid_usage_id cando_grabbed_usages[] = {
+	{ HID_ANY_ID, HID_ANY_ID, HID_ANY_ID },
+	{ HID_ANY_ID - 1, HID_ANY_ID - 1, HID_ANY_ID - 1}
+};
+
+static struct hid_driver cando_driver = {
+	.name = "cando-touch",
+	.id_table = cando_devices,
+	.probe = cando_probe,
+	.remove = cando_remove,
+	.input_mapping = cando_input_mapping,
+	.input_mapped = cando_input_mapped,
+	.usage_table = cando_grabbed_usages,
+	.event = cando_event,
+};
+
+static int __init cando_init(void)
+{
+	return hid_register_driver(&cando_driver);
+}
+
+static void __exit cando_exit(void)
+{
+	hid_unregister_driver(&cando_driver);
+}
+
+module_init(cando_init);
+module_exit(cando_exit);
+

drivers/hid/hid-core.c

@@ -653,10 +653,9 @@ int hid_parse_report(struct hid_device *device, __u8 *start,
 	if (device->driver->report_fixup)
 		device->driver->report_fixup(device, start, size);
 
-	device->rdesc = kmalloc(size, GFP_KERNEL);
+	device->rdesc = kmemdup(start, size, GFP_KERNEL);
 	if (device->rdesc == NULL)
 		return -ENOMEM;
-	memcpy(device->rdesc, start, size);
 	device->rsize = size;
 
 	parser = vmalloc(sizeof(struct hid_parser));
@@ -940,13 +939,8 @@ static void hid_output_field(struct hid_field *field, __u8 *data)
 	unsigned count = field->report_count;
 	unsigned offset = field->report_offset;
 	unsigned size = field->report_size;
-	unsigned bitsused = offset + count * size;
 	unsigned n;
 
-	/* make sure the unused bits in the last byte are zeros */
-	if (count > 0 && size > 0 && (bitsused % 8) != 0)
-		data[(bitsused-1)/8] &= (1 << (bitsused % 8)) - 1;
-
 	for (n = 0; n < count; n++) {
 		if (field->logical_minimum < 0)	/* signed values */
 			implement(data, offset + n * size, size, s32ton(field->value[n], size));
@@ -966,6 +960,7 @@ void hid_output_report(struct hid_report *report, __u8 *data)
 	if (report->id > 0)
 		*data++ = report->id;
 
+	memset(data, 0, ((report->size - 1) >> 3) + 1);
 	for (n = 0; n < report->maxfield; n++)
 		hid_output_field(report->field[n], data);
 }
@@ -1086,35 +1081,28 @@ int hid_input_report(struct hid_device *hid, int type, u8 *data, int size, int i
 
 	buf = kmalloc(sizeof(char) * HID_DEBUG_BUFSIZE, GFP_ATOMIC);
 
-	if (!buf) {
-		report = hid_get_report(report_enum, data);
+	if (!buf)
 		goto nomem;
-	}
-
-	snprintf(buf, HID_DEBUG_BUFSIZE - 1,
-			"\nreport (size %u) (%snumbered)\n", size, report_enum->numbered ? "" : "un");
-	hid_debug_event(hid, buf);
-
-	report = hid_get_report(report_enum, data);
-	if (!report) {
-		kfree(buf);
-		return -1;
-	}
 
 	/* dump the report */
 	snprintf(buf, HID_DEBUG_BUFSIZE - 1,
-			"report %d (size %u) = ", report->id, size);
+			"\nreport (size %u) (%snumbered) = ", size, report_enum->numbered ? "" : "un");
 	hid_debug_event(hid, buf);
+
 	for (i = 0; i < size; i++) {
 		snprintf(buf, HID_DEBUG_BUFSIZE - 1,
 				" %02x", data[i]);
 		hid_debug_event(hid, buf);
 	}
 	hid_debug_event(hid, "\n");
-
 	kfree(buf);
 
 nomem:
+	report = hid_get_report(report_enum, data);
+
+	if (!report)
+		return -1;
+
 	if (hdrv && hdrv->raw_event && hid_match_report(hid, report)) {
 		ret = hdrv->raw_event(hid, report, data, size);
 		if (ret != 0)
@@ -1167,6 +1155,8 @@ int hid_connect(struct hid_device *hdev, unsigned int connect_mask)
 	unsigned int i;
 	int len;
 
+	if (hdev->quirks & HID_QUIRK_HIDDEV_FORCE)
+		connect_mask |= (HID_CONNECT_HIDDEV_FORCE | HID_CONNECT_HIDDEV);
 	if (hdev->bus != BUS_USB)
 		connect_mask &= ~HID_CONNECT_HIDDEV;
 	if (hid_hiddev(hdev))
@@ -1246,6 +1236,7 @@ EXPORT_SYMBOL_GPL(hid_disconnect);
 /* a list of devices for which there is a specialized driver on HID bus */
 static const struct hid_device_id hid_blacklist[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_3M, USB_DEVICE_ID_3M1968) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_3M, USB_DEVICE_ID_3M2256) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_A4TECH, USB_DEVICE_ID_A4TECH_WCP32PU) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_A4TECH, USB_DEVICE_ID_A4TECH_X5_005D) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_ATV_IRCONTROL) },
@@ -1290,14 +1281,19 @@ static const struct hid_device_id hid_blacklist[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_FOUNTAIN_TP_ONLY) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER1_TP_ONLY) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_BELKIN, USB_DEVICE_ID_FLIP_KVM) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_BTC, USB_DEVICE_ID_BTC_EMPREX_REMOTE) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_CANDO, USB_DEVICE_ID_CANDO_MULTI_TOUCH) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_CANDO, USB_DEVICE_ID_CANDO_MULTI_TOUCH_11_6) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CHERRY, USB_DEVICE_ID_CHERRY_CYMOTION) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CHERRY, USB_DEVICE_ID_CHERRY_CYMOTION_SOLAR) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CHICONY, USB_DEVICE_ID_CHICONY_TACTICAL_PAD) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_CREATIVELABS, USB_DEVICE_ID_PRODIKEYS_PCMIDI) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_BARCODE_1) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_BARCODE_2) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_BARCODE_3) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_MOUSE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_DRAGONRISE, 0x0006) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_DWAV, USB_DEVICE_ID_DWAV_EGALAX_MULTITOUCH) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_EZKEY, USB_DEVICE_ID_BTC_8193) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_GAMERON, USB_DEVICE_ID_GAMERON_DUAL_PSX_ADAPTOR) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_GAMERON, USB_DEVICE_ID_GAMERON_DUAL_PCS_ADAPTOR) },
@@ -1331,6 +1327,8 @@ static const struct hid_device_id hid_blacklist[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_LOGITECH_RUMBLEPAD2) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACETRAVELLER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACENAVIGATOR) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_SIDEWINDER_GV) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_NE4K) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_LK6K) },
@@ -1342,7 +1340,9 @@ static const struct hid_device_id hid_blacklist[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PETALYNX, USB_DEVICE_ID_PETALYNX_MAXTER_REMOTE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_QUANTA, USB_DEVICE_ID_QUANTA_OPTICAL_TOUCH) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_QUANTA, USB_DEVICE_ID_PIXART_IMAGING_INC_OPTICAL_TOUCH_SCREEN) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_KONE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SAMSUNG, USB_DEVICE_ID_SAMSUNG_IR_REMOTE) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_SAMSUNG, USB_DEVICE_ID_SAMSUNG_WIRELESS_KBD_MOUSE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_PS3_CONTROLLER) },
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_PS3_CONTROLLER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_VAIO_VGX_MOUSE) },
@@ -1359,8 +1359,10 @@ static const struct hid_device_id hid_blacklist[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_TWINHAN, USB_DEVICE_ID_TWINHAN_IR_REMOTE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_WISEGROUP, USB_DEVICE_ID_SMARTJOY_PLUS) },
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_GRAPHIRE_BLUETOOTH) },
+	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_INTUOS4_BLUETOOTH) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ZEROPLUS, 0x0005) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ZEROPLUS, 0x0030) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ZYDACRON, USB_DEVICE_ID_ZYDACRON_REMOTE_CONTROL) },
 
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_PRESENTER_8K_BT) },
 	{ }
@@ -1757,7 +1759,7 @@ int hid_add_device(struct hid_device *hdev)
 
 	/* we need to kill them here, otherwise they will stay allocated to
 	 * wait for coming driver */
-	if (hid_ignore(hdev))
+	if (!(hdev->quirks & HID_QUIRK_NO_IGNORE) && hid_ignore(hdev))
 		return -ENODEV;
 
 	/* XXX hack, any other cleaner solution after the driver core
@@ -1765,11 +1767,12 @@ int hid_add_device(struct hid_device *hdev)
 	dev_set_name(&hdev->dev, "%04X:%04X:%04X.%04X", hdev->bus,
 		     hdev->vendor, hdev->product, atomic_inc_return(&id));
 
+	hid_debug_register(hdev, dev_name(&hdev->dev));
 	ret = device_add(&hdev->dev);
 	if (!ret)
 		hdev->status |= HID_STAT_ADDED;
-
-	hid_debug_register(hdev, dev_name(&hdev->dev));
+	else
+		hid_debug_unregister(hdev);
 
 	return ret;
 }

drivers/hid/hid-egalax.c

+/*
+ *  HID driver for eGalax dual-touch panels
+ *
+ *  Copyright (c) 2010 Stephane Chatty <chatty@enac.fr>
+ *
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <linux/device.h>
+#include <linux/hid.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+#include <linux/slab.h>
+#include "usbhid/usbhid.h"
+
+MODULE_AUTHOR("Stephane Chatty <chatty@enac.fr>");
+MODULE_DESCRIPTION("eGalax dual-touch panel");
+MODULE_LICENSE("GPL");
+
+#include "hid-ids.h"
+
+struct egalax_data {
+	__u16 x, y, z;
+	__u8 id;
+	bool first;		/* is this the first finger in the frame? */
+	bool valid;		/* valid finger data, or just placeholder? */
+	bool activity;		/* at least one active finger previously? */
+	__u16 lastx, lasty;	/* latest valid (x, y) in the frame */
+};
+
+static int egalax_input_mapping(struct hid_device *hdev, struct hid_input *hi,
+		struct hid_field *field, struct hid_usage *usage,
+		unsigned long **bit, int *max)
+{
+	switch (usage->hid & HID_USAGE_PAGE) {
+
+	case HID_UP_GENDESK:
+		switch (usage->hid) {
+		case HID_GD_X:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_POSITION_X);
+			/* touchscreen emulation */
+			input_set_abs_params(hi->input, ABS_X,
+						field->logical_minimum,
+						field->logical_maximum, 0, 0);
+			return 1;
+		case HID_GD_Y:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_POSITION_Y);
+			/* touchscreen emulation */
+			input_set_abs_params(hi->input, ABS_Y,
+						field->logical_minimum,
+						field->logical_maximum, 0, 0);
+			return 1;
+		}
+		return 0;
+
+	case HID_UP_DIGITIZER:
+		switch (usage->hid) {
+		case HID_DG_TIPSWITCH:
+			/* touchscreen emulation */
+			hid_map_usage(hi, usage, bit, max, EV_KEY, BTN_TOUCH);
+			return 1;
+		case HID_DG_INRANGE:
+		case HID_DG_CONFIDENCE:
+		case HID_DG_CONTACTCOUNT:
+		case HID_DG_CONTACTMAX:
+			return -1;
+		case HID_DG_CONTACTID:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_TRACKING_ID);
+			return 1;
+		case HID_DG_TIPPRESSURE:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_PRESSURE);
+			return 1;
+		}
+		return 0;
+	}
+
+	/* ignore others (from other reports we won't get anyway) */
+	return -1;
+}
+
+static int egalax_input_mapped(struct hid_device *hdev, struct hid_input *hi,
+		struct hid_field *field, struct hid_usage *usage,
+		unsigned long **bit, int *max)
+{
+	if (usage->type == EV_KEY || usage->type == EV_ABS)
+		clear_bit(usage->code, *bit);
+
+	return 0;
+}
+
+/*
+ * this function is called when a whole finger has been parsed,
+ * so that it can decide what to send to the input layer.
+ */
+static void egalax_filter_event(struct egalax_data *td, struct input_dev *input)
+{
+	td->first = !td->first; /* touchscreen emulation */
+
+	if (td->valid) {
+		/* emit multitouch events */
+		input_event(input, EV_ABS, ABS_MT_TRACKING_ID, td->id);
+		input_event(input, EV_ABS, ABS_MT_POSITION_X, td->x);
+		input_event(input, EV_ABS, ABS_MT_POSITION_Y, td->y);
+		input_event(input, EV_ABS, ABS_MT_PRESSURE, td->z);
+
+		input_mt_sync(input);
+
+		/*
+		 * touchscreen emulation: store (x, y) as
+		 * the last valid values in this frame
+		 */
+		td->lastx = td->x;
+		td->lasty = td->y;
+	}
+
+	/*
+	 * touchscreen emulation: if this is the second finger and at least
+	 * one in this frame is valid, the latest valid in the frame is
+	 * the oldest on the panel, the one we want for single touch
+	 */
+	if (!td->first && td->activity) {
+		input_event(input, EV_ABS, ABS_X, td->lastx);
+		input_event(input, EV_ABS, ABS_Y, td->lasty);
+	}
+
+	if (!td->valid) {
+		/*
+		 * touchscreen emulation: if the first finger is invalid
+		 * and there previously was finger activity, this is a release
+		 */ 
+		if (td->first && td->activity) {
+			input_event(input, EV_KEY, BTN_TOUCH, 0);
+			td->activity = false;
+		}
+		return;
+	}
+
+
+	/* touchscreen emulation: if no previous activity, emit touch event */
+	if (!td->activity) {
+		input_event(input, EV_KEY, BTN_TOUCH, 1);
+		td->activity = true;
+	}
+}
+
+
+static int egalax_event(struct hid_device *hid, struct hid_field *field,
+				struct hid_usage *usage, __s32 value)
+{
+	struct egalax_data *td = hid_get_drvdata(hid);
+
+	if (hid->claimed & HID_CLAIMED_INPUT) {
+		struct input_dev *input = field->hidinput->input;
+
+		switch (usage->hid) {
+		case HID_DG_INRANGE:
+		case HID_DG_CONFIDENCE:
+			/* avoid interference from generic hidinput handling */
+			break;
+		case HID_DG_TIPSWITCH:
+			td->valid = value;
+			break;
+		case HID_DG_TIPPRESSURE:
+			td->z = value;
+			break;
+		case HID_DG_CONTACTID:
+			td->id = value;
+			break;
+		case HID_GD_X:
+			td->x = value;
+			break;
+		case HID_GD_Y:
+			td->y = value;
+			/* this is the last field in a finger */
+			egalax_filter_event(td, input);
+			break;
+		case HID_DG_CONTACTCOUNT:
+			/* touch emulation: this is the last field in a frame */
+			td->first = false;
+			break;
+
+		default:
+			/* fallback to the generic hidinput handling */
+			return 0;
+		}
+	}
+
+	/* we have handled the hidinput part, now remains hiddev */
+	if (hid->claimed & HID_CLAIMED_HIDDEV && hid->hiddev_hid_event)
+		hid->hiddev_hid_event(hid, field, usage, value);
+
+	return 1;
+}
+
+static int egalax_probe(struct hid_device *hdev, const struct hid_device_id *id)
+{
+	int ret;
+	struct egalax_data *td;
+	struct hid_report *report;
+
+	td = kmalloc(sizeof(struct egalax_data), GFP_KERNEL);
+	if (!td) {
+		dev_err(&hdev->dev, "cannot allocate eGalax data\n");
+		return -ENOMEM;
+	}
+	hid_set_drvdata(hdev, td);
+
+	ret = hid_parse(hdev);
+	if (ret)
+		goto end;
+
+	ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
+	if (ret)
+		goto end;
+
+	report = hdev->report_enum[HID_FEATURE_REPORT].report_id_hash[5]; 
+	if (report) {
+		report->field[0]->value[0] = 2;
+		usbhid_submit_report(hdev, report, USB_DIR_OUT);
+	}
+
+end:
+	if (ret)
+		kfree(td);
+
+	return ret;
+}
+
+static void egalax_remove(struct hid_device *hdev)
+{
+	hid_hw_stop(hdev);
+	kfree(hid_get_drvdata(hdev));
+	hid_set_drvdata(hdev, NULL);
+}
+
+static const struct hid_device_id egalax_devices[] = {
+	{ HID_USB_DEVICE(USB_VENDOR_ID_DWAV,
+			USB_DEVICE_ID_DWAV_EGALAX_MULTITOUCH) },
+	{ }
+};
+MODULE_DEVICE_TABLE(hid, egalax_devices);
+
+static const struct hid_usage_id egalax_grabbed_usages[] = {
+	{ HID_ANY_ID, HID_ANY_ID, HID_ANY_ID },
+	{ HID_ANY_ID - 1, HID_ANY_ID - 1, HID_ANY_ID - 1}
+};
+
+static struct hid_driver egalax_driver = {
+	.name = "egalax-touch",
+	.id_table = egalax_devices,
+	.probe = egalax_probe,
+	.remove = egalax_remove,
+	.input_mapping = egalax_input_mapping,
+	.input_mapped = egalax_input_mapped,
+	.usage_table = egalax_grabbed_usages,
+	.event = egalax_event,
+};
+
+static int __init egalax_init(void)
+{
+	return hid_register_driver(&egalax_driver);
+}
+
+static void __exit egalax_exit(void)
+{
+	hid_unregister_driver(&egalax_driver);
+}
+
+module_init(egalax_init);
+module_exit(egalax_exit);
+

drivers/hid/hid-ids.h

@@ -20,6 +20,7 @@
 
 #define USB_VENDOR_ID_3M		0x0596
 #define USB_DEVICE_ID_3M1968		0x0500
+#define USB_DEVICE_ID_3M2256		0x0502
 
 #define USB_VENDOR_ID_A4TECH		0x09da
 #define USB_DEVICE_ID_A4TECH_WCP32PU	0x0006
@@ -123,6 +124,13 @@
 #define USB_VENDOR_ID_BERKSHIRE		0x0c98
 #define USB_DEVICE_ID_BERKSHIRE_PCWD	0x1140
 
+#define USB_VENDOR_ID_BTC		0x046e
+#define USB_DEVICE_ID_BTC_EMPREX_REMOTE	0x5578
+
+#define USB_VENDOR_ID_CANDO		0x2087
+#define USB_DEVICE_ID_CANDO_MULTI_TOUCH 0x0a01
+#define USB_DEVICE_ID_CANDO_MULTI_TOUCH_11_6 0x0b03
+
 #define USB_VENDOR_ID_CH		0x068e
 #define USB_DEVICE_ID_CH_PRO_PEDALS	0x00f2
 #define USB_DEVICE_ID_CH_COMBATSTICK	0x00f4
@@ -148,6 +156,9 @@
 #define USB_DEVICE_ID_CODEMERCS_IOW_FIRST	0x1500
 #define USB_DEVICE_ID_CODEMERCS_IOW_LAST	0x15ff
 
+#define USB_VENDOR_ID_CREATIVELABS	0x041e
+#define USB_DEVICE_ID_PRODIKEYS_PCMIDI	0x2801
+
 #define USB_VENDOR_ID_CYGNAL		0x10c4
 #define USB_DEVICE_ID_CYGNAL_RADIO_SI470X	0x818a
 
@@ -171,6 +182,10 @@
 
 #define USB_VENDOR_ID_DRAGONRISE	0x0079
 
+#define USB_VENDOR_ID_DWAV		0x0eef
+#define USB_DEVICE_ID_EGALAX_TOUCHCONTROLLER	0x0001
+#define USB_DEVICE_ID_DWAV_EGALAX_MULTITOUCH	0x480d
+
 #define USB_VENDOR_ID_ELO		0x04E7
 #define USB_DEVICE_ID_ELO_TS2700	0x0020
 
@@ -342,6 +357,8 @@
 #define USB_VENDOR_ID_MICROCHIP		0x04d8
 #define USB_DEVICE_ID_PICKIT1		0x0032
 #define USB_DEVICE_ID_PICKIT2		0x0033
+#define USB_DEVICE_ID_PICOLCD		0xc002
+#define USB_DEVICE_ID_PICOLCD_BOOTLOADER	0xf002
 
 #define USB_VENDOR_ID_MICROSOFT		0x045e
 #define USB_DEVICE_ID_SIDEWINDER_GV	0x003b
@@ -400,6 +417,9 @@
 #define USB_VENDOR_ID_PRODIGE		0x05af
 #define USB_DEVICE_ID_PRODIGE_CORDLESS	0x3062
 
+#define USB_VENDOR_ID_ROCCAT		0x1e7d
+#define USB_DEVICE_ID_ROCCAT_KONE	0x2ced
+
 #define USB_VENDOR_ID_SAITEK		0x06a3
 #define USB_DEVICE_ID_SAITEK_RUMBLEPAD	0xff17
 
@@ -409,6 +429,7 @@
 
 #define USB_VENDOR_ID_SAMSUNG		0x0419
 #define USB_DEVICE_ID_SAMSUNG_IR_REMOTE	0x0001
+#define USB_DEVICE_ID_SAMSUNG_WIRELESS_KBD_MOUSE	0x0600
 
 #define USB_VENDOR_ID_SONY			0x054c
 #define USB_DEVICE_ID_SONY_VAIO_VGX_MOUSE	0x024b
@@ -457,6 +478,7 @@
 
 #define USB_VENDOR_ID_WACOM		0x056a
 #define USB_DEVICE_ID_WACOM_GRAPHIRE_BLUETOOTH	0x81
+#define USB_DEVICE_ID_WACOM_INTUOS4_BLUETOOTH	0xbd
 
 #define USB_VENDOR_ID_WISEGROUP		0x0925
 #define USB_DEVICE_ID_SMARTJOY_PLUS	0x0005
@@ -475,6 +497,9 @@
 
 #define USB_VENDOR_ID_ZEROPLUS		0x0c12
 
+#define USB_VENDOR_ID_ZYDACRON	0x13EC
+#define USB_DEVICE_ID_ZYDACRON_REMOTE_CONTROL	0x0006
+
 #define USB_VENDOR_ID_KYE		0x0458
 #define USB_DEVICE_ID_KYE_ERGO_525V	0x0087
 #define USB_DEVICE_ID_KYE_GPEN_560	0x5003

drivers/hid/hid-lg.c

@@ -126,6 +126,9 @@ static int lg_wireless_mapping(struct hid_input *hi, struct hid_usage *usage,
 	case 0x1004: lg_map_key_clear(KEY_VIDEO);		break;
 	case 0x1005: lg_map_key_clear(KEY_AUDIO);		break;
 	case 0x100a: lg_map_key_clear(KEY_DOCUMENTS);		break;
+	/* The following two entries are Playlist 1 and 2 on the MX3200 */
+	case 0x100f: lg_map_key_clear(KEY_FN_1);		break;
+	case 0x1010: lg_map_key_clear(KEY_FN_2);		break;
 	case 0x1011: lg_map_key_clear(KEY_PREVIOUSSONG);	break;
 	case 0x1012: lg_map_key_clear(KEY_NEXTSONG);		break;
 	case 0x1013: lg_map_key_clear(KEY_CAMERA);		break;
@@ -137,6 +140,7 @@ static int lg_wireless_mapping(struct hid_input *hi, struct hid_usage *usage,
 	case 0x1019: lg_map_key_clear(KEY_PROG1);		break;
 	case 0x101a: lg_map_key_clear(KEY_PROG2);		break;
 	case 0x101b: lg_map_key_clear(KEY_PROG3);		break;
+	case 0x101c: lg_map_key_clear(KEY_CYCLEWINDOWS);	break;
 	case 0x101f: lg_map_key_clear(KEY_ZOOMIN);		break;
 	case 0x1020: lg_map_key_clear(KEY_ZOOMOUT);		break;
 	case 0x1021: lg_map_key_clear(KEY_ZOOMRESET);		break;
@@ -147,6 +151,11 @@ static int lg_wireless_mapping(struct hid_input *hi, struct hid_usage *usage,
 	case 0x1029: lg_map_key_clear(KEY_SHUFFLE);		break;
 	case 0x102a: lg_map_key_clear(KEY_BACK);		break;
 	case 0x102b: lg_map_key_clear(KEY_CYCLEWINDOWS);	break;
+	case 0x102d: lg_map_key_clear(KEY_WWW);			break;
+	/* The following two are 'Start/answer call' and 'End/reject call'
+	   on the MX3200 */
+	case 0x1031: lg_map_key_clear(KEY_OK);			break;
+	case 0x1032: lg_map_key_clear(KEY_CANCEL);		break;
 	case 0x1041: lg_map_key_clear(KEY_BATTERY);		break;
 	case 0x1042: lg_map_key_clear(KEY_WORDPROCESSOR);	break;
 	case 0x1043: lg_map_key_clear(KEY_SPREADSHEET);		break;

drivers/hid/hid-magicmouse.c

@@ -354,12 +354,15 @@ static int magicmouse_probe(struct hid_device *hdev,
 		goto err_free;
 	}
 
-	ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT & ~HID_CONNECT_HIDINPUT);
+	ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
 	if (ret) {
 		dev_err(&hdev->dev, "magicmouse hw start failed\n");
 		goto err_free;
 	}
 
+	/* we are handling the input ourselves */
+	hidinput_disconnect(hdev);
+
 	report = hid_register_report(hdev, HID_INPUT_REPORT, TOUCH_REPORT_ID);
 	if (!report) {
 		dev_err(&hdev->dev, "unable to register touch report\n");

drivers/hid/hid-roccat-kone.h

+#ifndef __HID_ROCCAT_KONE_H
+#define __HID_ROCCAT_KONE_H
+
+/*
+ * Copyright (c) 2010 Stefan Achatz <erazor_de@users.sourceforge.net>
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <linux/types.h>
+
+#define ROCCAT_KONE_DRIVER_VERSION "v0.3.1"
+
+#pragma pack(push)
+#pragma pack(1)
+
+struct kone_keystroke {
+	uint8_t key;
+	uint8_t action;
+	uint16_t period; /* in milliseconds */
+};
+
+enum kone_keystroke_buttons {
+	kone_keystroke_button_1 = 0xf0, /* left mouse button */
+	kone_keystroke_button_2 = 0xf1, /* right mouse button */
+	kone_keystroke_button_3 = 0xf2, /* wheel */
+	kone_keystroke_button_9 = 0xf3, /* side button up */
+	kone_keystroke_button_8 = 0xf4 /* side button down */
+};
+
+enum kone_keystroke_actions {
+	kone_keystroke_action_press = 0,
+	kone_keystroke_action_release = 1
+};
+
+struct kone_button_info {
+	uint8_t number; /* range 1-8 */
+	uint8_t type;
+	uint8_t macro_type; /* 0 = short, 1 = overlong */
+	uint8_t macro_set_name[16]; /* can be max 15 chars long */
+	uint8_t macro_name[16]; /* can be max 15 chars long */
+	uint8_t count;
+	struct kone_keystroke keystrokes[20];
+};
+
+enum kone_button_info_types {
+	/* valid button types until firmware 1.32 */
+	kone_button_info_type_button_1 = 0x1, /* click (left mouse button) */
+	kone_button_info_type_button_2 = 0x2, /* menu (right mouse button)*/
+	kone_button_info_type_button_3 = 0x3, /* scroll (wheel) */
+	kone_button_info_type_double_click = 0x4,
+	kone_button_info_type_key = 0x5,
+	kone_button_info_type_macro = 0x6,
+	kone_button_info_type_off = 0x7,
+	/* TODO clarify function and rename */
+	kone_button_info_type_osd_xy_prescaling = 0x8,
+	kone_button_info_type_osd_dpi = 0x9,
+	kone_button_info_type_osd_profile = 0xa,
+	kone_button_info_type_button_9 = 0xb, /* ie forward */
+	kone_button_info_type_button_8 = 0xc, /* ie backward */
+	kone_button_info_type_dpi_up = 0xd, /* internal */
+	kone_button_info_type_dpi_down = 0xe, /* internal */
+	kone_button_info_type_button_7 = 0xf, /* tilt left */
+	kone_button_info_type_button_6 = 0x10, /* tilt right */
+	kone_button_info_type_profile_up = 0x11, /* internal */
+	kone_button_info_type_profile_down = 0x12, /* internal */
+	/* additional valid button types since firmware 1.38 */
+	kone_button_info_type_multimedia_open_player = 0x20,
+	kone_button_info_type_multimedia_next_track = 0x21,
+	kone_button_info_type_multimedia_prev_track = 0x22,
+	kone_button_info_type_multimedia_play_pause = 0x23,
+	kone_button_info_type_multimedia_stop = 0x24,
+	kone_button_info_type_multimedia_mute = 0x25,
+	kone_button_info_type_multimedia_volume_up = 0x26,
+	kone_button_info_type_multimedia_volume_down = 0x27
+};
+
+enum kone_button_info_numbers {
+	kone_button_top = 1,
+	kone_button_wheel_tilt_left = 2,
+	kone_button_wheel_tilt_right = 3,
+	kone_button_forward = 4,
+	kone_button_backward = 5,
+	kone_button_middle = 6,
+	kone_button_plus = 7,
+	kone_button_minus = 8,
+};
+
+struct kone_light_info {
+	uint8_t number; /* number of light 1-5 */
+	uint8_t mod;   /* 1 = on, 2 = off */
+	uint8_t red;   /* range 0x00-0xff */
+	uint8_t green; /* range 0x00-0xff */
+	uint8_t blue;  /* range 0x00-0xff */
+};
+
+struct kone_profile {
+	uint16_t size; /* always 975 */
+	uint16_t unused; /* always 0 */
+
+	/*
+	 * range 1-5
+	 * This number does not need to correspond with location where profile
+	 * saved
+	 */
+	uint8_t profile; /* range 1-5 */
+
+	uint16_t main_sensitivity; /* range 100-1000 */
+	uint8_t xy_sensitivity_enabled; /* 1 = on, 2 = off */
+	uint16_t x_sensitivity; /* range 100-1000 */
+	uint16_t y_sensitivity; /* range 100-1000 */
+	uint8_t dpi_rate; /* bit 1 = 800, ... */
+	uint8_t startup_dpi; /* range 1-6 */
+	uint8_t polling_rate; /* 1 = 125Hz, 2 = 500Hz, 3 = 1000Hz */
+	/* kone has no dcu
+	 * value is always 2 in firmwares <= 1.32 and
+	 * 1 in firmwares > 1.32
+	 */
+	uint8_t dcu_flag;
+	uint8_t light_effect_1; /* range 1-3 */
+	uint8_t light_effect_2; /* range 1-5 */
+	uint8_t light_effect_3; /* range 1-4 */
+	uint8_t light_effect_speed; /* range 0-255 */
+
+	struct kone_light_info light_infos[5];
+	/* offset is kone_button_info_numbers - 1 */
+	struct kone_button_info button_infos[8];
+
+	uint16_t checksum; /* \brief holds checksum of struct */
+};
+
+enum kone_polling_rates {
+	kone_polling_rate_125 = 1,
+	kone_polling_rate_500 = 2,
+	kone_polling_rate_1000 = 3
+};
+
+struct kone_settings {
+	uint16_t size; /* always 36 */
+	uint8_t  startup_profile; /* 1-5 */
+	uint8_t	 unknown1;
+	uint8_t  tcu; /* 0 = off, 1 = on */
+	uint8_t  unknown2[23];
+	uint8_t  calibration_data[4];
+	uint8_t  unknown3[2];
+	uint16_t checksum;
+};
+
+/*
+ * 12 byte mouse event read by interrupt_read
+ */
+struct kone_mouse_event {
+	uint8_t report_number; /* always 1 */
+	uint8_t button;
+	uint16_t x;
+	uint16_t y;
+	uint8_t wheel; /* up = 1, down = -1 */
+	uint8_t tilt; /* right = 1, left = -1 */
+	uint8_t unknown;
+	uint8_t event;
+	uint8_t value; /* press = 0, release = 1 */
+	uint8_t macro_key; /* 0 to 8 */
+};
+
+enum kone_mouse_events {
+	/* osd events are thought to be display on screen */
+	kone_mouse_event_osd_dpi = 0xa0,
+	kone_mouse_event_osd_profile = 0xb0,
+	/* TODO clarify meaning and occurence of kone_mouse_event_calibration */
+	kone_mouse_event_calibration = 0xc0,
+	kone_mouse_event_call_overlong_macro = 0xe0,
+	/* switch events notify if user changed values with mousebutton click */
+	kone_mouse_event_switch_dpi = 0xf0,
+	kone_mouse_event_switch_profile = 0xf1
+};
+
+enum kone_commands {
+	kone_command_profile = 0x5a,
+	kone_command_settings = 0x15a,
+	kone_command_firmware_version = 0x25a,
+	kone_command_weight = 0x45a,
+	kone_command_calibrate = 0x55a,
+	kone_command_confirm_write = 0x65a,
+	kone_command_firmware = 0xe5a
+};
+
+#pragma pack(pop)
+
+struct kone_device {
+	/*
+	 * Storing actual values when we get informed about changes since there
+	 * is no way of getting this information from the device on demand
+	 */
+	int actual_profile, actual_dpi;
+	/* Used for neutralizing abnormal button behaviour */
+	struct kone_mouse_event last_mouse_event;
+
+	/*
+	 * It's unlikely that multiple sysfs attributes are accessed at a time,
+	 * so only one mutex is used to secure hardware access and profiles and
+	 * settings of this struct.
+	 */
+	struct mutex kone_lock;
+
+	/*
+	 * Storing the data here reduces IO and ensures that data is available
+	 * when its needed (E.g. interrupt handler).
+	 */
+	struct kone_profile profiles[5];
+	struct kone_settings settings;
+
+	/*
+	 * firmware doesn't change unless firmware update is implemented,
+	 * so it's read only once
+	 */
+	int firmware_version;
+};
+
+#endif

drivers/hid/hid-topseed.c

@@ -3,6 +3,9 @@
  *
  *  Copyright (c) 2008 Lev Babiev
  *  based on hid-cherry driver
+ *
+ *  Modified to also support BTC "Emprex 3009URF III Vista MCE Remote" by
+ *  Wayne Thomas 2010.
  */
 
 /*
@@ -24,23 +27,29 @@ static int ts_input_mapping(struct hid_device *hdev, struct hid_input *hi,
 		struct hid_field *field, struct hid_usage *usage,
 		unsigned long **bit, int *max)
 {
-	if ((usage->hid & HID_USAGE_PAGE) != 0x0ffbc0000)
+	if ((usage->hid & HID_USAGE_PAGE) != HID_UP_LOGIVENDOR)
 		return 0;
 
 	switch (usage->hid & HID_USAGE) {
-        case 0x00d: ts_map_key_clear(KEY_HOME);           break;
-        case 0x024: ts_map_key_clear(KEY_MENU);           break;
-        case 0x025: ts_map_key_clear(KEY_TV);             break;
-        case 0x048: ts_map_key_clear(KEY_RED);            break;
-        case 0x047: ts_map_key_clear(KEY_GREEN);          break;
-        case 0x049: ts_map_key_clear(KEY_YELLOW);         break;
-        case 0x04a: ts_map_key_clear(KEY_BLUE);           break;
-        case 0x04b: ts_map_key_clear(KEY_ANGLE);          break;
-        case 0x04c: ts_map_key_clear(KEY_LANGUAGE);       break;
-        case 0x04d: ts_map_key_clear(KEY_SUBTITLE);       break;
-        case 0x031: ts_map_key_clear(KEY_AUDIO);          break;
-        case 0x032: ts_map_key_clear(KEY_TEXT);           break;
-        case 0x033: ts_map_key_clear(KEY_CHANNEL);        break;
+	case 0x00d: ts_map_key_clear(KEY_MEDIA);	break;
+	case 0x024: ts_map_key_clear(KEY_MENU);		break;
+	case 0x025: ts_map_key_clear(KEY_TV);		break;
+	case 0x031: ts_map_key_clear(KEY_AUDIO);	break;
+	case 0x032: ts_map_key_clear(KEY_TEXT);		break;
+	case 0x033: ts_map_key_clear(KEY_CHANNEL);	break;
+	case 0x047: ts_map_key_clear(KEY_MP3);		break;
+	case 0x048: ts_map_key_clear(KEY_TV2);		break;
+	case 0x049: ts_map_key_clear(KEY_CAMERA);	break;
+	case 0x04a: ts_map_key_clear(KEY_VIDEO);	break;
+	case 0x04b: ts_map_key_clear(KEY_ANGLE);	break;
+	case 0x04c: ts_map_key_clear(KEY_LANGUAGE);	break;
+	case 0x04d: ts_map_key_clear(KEY_SUBTITLE);	break;
+	case 0x050: ts_map_key_clear(KEY_RADIO);	break;
+	case 0x05a: ts_map_key_clear(KEY_TEXT);		break;
+	case 0x05b: ts_map_key_clear(KEY_RED);		break;
+	case 0x05c: ts_map_key_clear(KEY_GREEN);	break;
+	case 0x05d: ts_map_key_clear(KEY_YELLOW);	break;
+	case 0x05e: ts_map_key_clear(KEY_BLUE);		break;
 	default:
 		return 0;
 	}
@@ -50,6 +59,7 @@ static int ts_input_mapping(struct hid_device *hdev, struct hid_input *hi,
 
 static const struct hid_device_id ts_devices[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_TOPSEED, USB_DEVICE_ID_TOPSEED_CYBERLINK) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_BTC, USB_DEVICE_ID_BTC_EMPREX_REMOTE) },
 	{ }
 };
 MODULE_DEVICE_TABLE(hid, ts_devices);

drivers/hid/usbhid/hid-quirks.c

@@ -33,6 +33,7 @@ static const struct hid_blacklist {
 	{ USB_VENDOR_ID_AASHIMA, USB_DEVICE_ID_AASHIMA_PREDATOR, HID_QUIRK_BADPAD },
 	{ USB_VENDOR_ID_ALPS, USB_DEVICE_ID_IBM_GAMEPAD, HID_QUIRK_BADPAD },
 	{ USB_VENDOR_ID_CHIC, USB_DEVICE_ID_CHIC_GAMEPAD, HID_QUIRK_BADPAD },
+	{ USB_VENDOR_ID_DWAV, USB_DEVICE_ID_DWAV_EGALAX_MULTITOUCH, HID_QUIRK_MULTI_INPUT },
 	{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_DRIVING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
 	{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FLYING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
 	{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FIGHTING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },

drivers/hid/usbhid/hiddev.c

@@ -267,6 +267,7 @@ static int hiddev_open(struct inode *inode, struct file *file)
 	struct hiddev_list *list;
 	int res, i;
 
+	/* See comment in hiddev_connect() for BKL explanation */
 	lock_kernel();
 	i = iminor(inode) - HIDDEV_MINOR_BASE;
 
@@ -894,8 +895,22 @@ int hiddev_connect(struct hid_device *hid, unsigned int force)
 	hiddev->hid = hid;
 	hiddev->exist = 1;
 
-	/* when lock_kernel() usage is fixed in usb_open(),
-	 * we could also fix it here */
+	/*
+	 * BKL here is used to avoid race after usb_register_dev().
+	 * Once the device node has been created, open() could happen on it.
+	 * The code below will then fail, as hiddev_table hasn't been
+	 * updated.
+	 *
+	 * The obvious fix -- introducing mutex to guard hiddev_table[]
+	 * doesn't work, as usb_open() and usb_register_dev() both take
+	 * minor_rwsem, thus we'll have ABBA deadlock.
+	 *
+	 * Before BKL pushdown, usb_open() had been acquiring it in right
+	 * order, so _open() was safe to use it to protect from this race.
+	 * Now the order is different, but AB-BA deadlock still doesn't occur
+	 * as BKL is dropped on schedule() (i.e. while sleeping on
+	 * minor_rwsem). Fugly.
+	 */
 	lock_kernel();
 	retval = usb_register_dev(usbhid->intf, &hiddev_class);
 	if (retval) {

drivers/hid/usbhid/usbkbd.c

@@ -311,6 +311,7 @@ static int usb_kbd_probe(struct usb_interface *iface,
 		goto fail2;
 
 	usb_set_intfdata(iface, kbd);
+	device_set_wakeup_enable(&dev->dev, 1);
 	return 0;
 
 fail2: