Commit 8d362cb3 authored by Alexey Brodkin's avatar Alexey Brodkin Committed by Greg Kroah-Hartman

ARCv2: PAE40: Explicitly set MSB counterpart of SLC region ops addresses

commit 7d79cee2 upstream.

It is necessary to explicitly set both SLC_AUX_RGN_START1 and SLC_AUX_RGN_END1
which hold MSB bits of the physical address correspondingly of region start
and end otherwise SLC region operation is executed in unpredictable manner

Without this patch, SLC flushes on HSDK (IOC disabled) were taking
seconds.
Reported-by: default avatarVladimir Kondratiev <vladimir.kondratiev@intel.com>
Signed-off-by: default avatarAlexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: default avatarVineet Gupta <vgupta@synopsys.com>
[vgupta: PAR40 regs only written if PAE40 exist]
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 6cba0746
...@@ -89,7 +89,9 @@ extern unsigned long perip_base, perip_end; ...@@ -89,7 +89,9 @@ extern unsigned long perip_base, perip_end;
#define ARC_REG_SLC_FLUSH 0x904 #define ARC_REG_SLC_FLUSH 0x904
#define ARC_REG_SLC_INVALIDATE 0x905 #define ARC_REG_SLC_INVALIDATE 0x905
#define ARC_REG_SLC_RGN_START 0x914 #define ARC_REG_SLC_RGN_START 0x914
#define ARC_REG_SLC_RGN_START1 0x915
#define ARC_REG_SLC_RGN_END 0x916 #define ARC_REG_SLC_RGN_END 0x916
#define ARC_REG_SLC_RGN_END1 0x917
/* Bit val in SLC_CONTROL */ /* Bit val in SLC_CONTROL */
#define SLC_CTRL_IM 0x040 #define SLC_CTRL_IM 0x040
......
...@@ -562,6 +562,7 @@ noinline void slc_op(phys_addr_t paddr, unsigned long sz, const int op) ...@@ -562,6 +562,7 @@ noinline void slc_op(phys_addr_t paddr, unsigned long sz, const int op)
static DEFINE_SPINLOCK(lock); static DEFINE_SPINLOCK(lock);
unsigned long flags; unsigned long flags;
unsigned int ctrl; unsigned int ctrl;
phys_addr_t end;
spin_lock_irqsave(&lock, flags); spin_lock_irqsave(&lock, flags);
...@@ -591,8 +592,16 @@ noinline void slc_op(phys_addr_t paddr, unsigned long sz, const int op) ...@@ -591,8 +592,16 @@ noinline void slc_op(phys_addr_t paddr, unsigned long sz, const int op)
* END needs to be setup before START (latter triggers the operation) * END needs to be setup before START (latter triggers the operation)
* END can't be same as START, so add (l2_line_sz - 1) to sz * END can't be same as START, so add (l2_line_sz - 1) to sz
*/ */
write_aux_reg(ARC_REG_SLC_RGN_END, (paddr + sz + l2_line_sz - 1)); end = paddr + sz + l2_line_sz - 1;
write_aux_reg(ARC_REG_SLC_RGN_START, paddr); if (is_pae40_enabled())
write_aux_reg(ARC_REG_SLC_RGN_END1, upper_32_bits(end));
write_aux_reg(ARC_REG_SLC_RGN_END, lower_32_bits(end));
if (is_pae40_enabled())
write_aux_reg(ARC_REG_SLC_RGN_START1, upper_32_bits(paddr));
write_aux_reg(ARC_REG_SLC_RGN_START, lower_32_bits(paddr));
while (read_aux_reg(ARC_REG_SLC_CTRL) & SLC_CTRL_BUSY); while (read_aux_reg(ARC_REG_SLC_CTRL) & SLC_CTRL_BUSY);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment