[PATCH] Documentation fixes in intel810.txt

Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Documentation/fb/intel810.txt

@@ -9,8 +9,9 @@ Intel 810/815 Framebuffer driver
 ================================================================
 
 A. Introduction
+
 	This is a framebuffer driver for various Intel 810/815 compatible
-graphics devices.  These would include:
+	graphics devices.  These include:
 
 	Intel 810
 	Intel 810E
@@ -24,7 +25,7 @@ B.  Features
 	- Choice of using Discrete Video Timings, VESA Generalized Timing
 	  Formula, or a framebuffer specific database to set the video mode
 
-	- Supports a variable range of horizontal and vertical resolution, and
+	- Supports a variable range of horizontal and vertical resolution and
 	  vertical refresh rates if the VESA Generalized Timing Formula is
 	  enabled.
 
@@ -91,12 +92,12 @@ C.  List of available options
 
    g. "hsync1/hsync2:<value>"
 	select the minimum and maximum Horizontal Sync Frequency of the
-	monitor in KHz.  If a using a fixed frequency monitor, hsync1 must 
+	monitor in kHz.  If using a fixed frequency monitor, hsync1 must
 	be equal to hsync2. If EDID probing is successful, these will be
 	ignored and values will be taken from the EDID block.
 
 	Recommendation: check monitor manual for correct values
-	default (29/30)
+	(default = 29/30)
 
    h. "vsync1/vsync2:<value>"
 	select the minimum and maximum Vertical Sync Frequency of the monitor
@@ -116,9 +117,9 @@ C.  List of available options
 	select at what offset in MB of the logical memory to allocate the
 	framebuffer memory.  The intent is to avoid the memory blocks
 	used by standard graphics applications (XFree86).  The default
-        offset (16 MB for a 64MB aperture, 8 MB for a 32MB aperture) will
-        avoid XFree86's usage and allows up to 7MB/15MB of framebuffer
-        memory.  Depending on your usage, adjust the value up or down, 
+	offset (16 MB for a 64 MB aperture, 8 MB for a 32 MB aperture) will
+	avoid XFree86's usage and allows up to 7 MB/15 MB of framebuffer
+	memory.  Depending on your usage, adjust the value up or down
 	(0 for maximum usage, 31/63 MB for the least amount).  Note, an
 	arbitrary setting may conflict with XFree86.
 
@@ -162,6 +163,7 @@ C.  List of available options
 
 	Recommendation: do not set
 	(default = not set)
+
    o. <xres>x<yres>[-<bpp>][@<refresh>]
 	The driver will now accept specification of boot mode option.  If this
 	is specified, the options 'xres' and 'yres' will be ignored. See
@@ -195,7 +197,7 @@ block.
 
 E.  Module options
 
-	The module parameters are essentially similar to the kernel 
+The module parameters are essentially similar to the kernel
 parameters. The main difference is that you need to include a Boolean value
 (1 for TRUE, and 0 for FALSE) for those options which don't need a value.
 
@@ -225,11 +227,11 @@ F.  Setup
 
 	make menuconfig/xconfig/config
 
-	b. Under "Code Maturity Options", enable "Prompt for experimental/
-	   incomplete code/drivers".
+	b. Under "Code maturity level options" enable "Prompt for development
+	   and/or incomplete code/drivers".
 
  	c. Enable agpgart support for the Intel 810/815 on-board graphics.
-	   This is required.  The option is under "Character Devices"
+	   This is required.  The option is under "Character Devices".
 
 	d. Under "Graphics Support", select "Intel 810/815" either statically
 	   or as a module.  Choose "use VESA Generalized Timing Formula" if
@@ -241,11 +243,11 @@ F.  Setup
 	   'use VESA Generalized Timing Formula' to 'y'.
 
         f. If you want a framebuffer console, enable it under "Console
-	   Drivers"
+	   Drivers".
 
 	g. Compile your kernel.
 
-	h. Load the driver as described in section D and E.
+	h. Load the driver as described in sections D and E.
 
 	i.  Try the DirectFB (http://www.directfb.org) + the i810 gfxdriver
 	    patch to see the chipset in action (or inaction :-).
@@ -269,7 +271,7 @@ G.  Acknowledgment:
 H.  Home Page:
 
 	A more complete, and probably updated information is provided at
-http://i810fb.sourceforge.net.
+	http://i810fb.sourceforge.net.
 
 ###########################
 Tony