Merge git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc

* git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (53 commits)
  powerpc: Support for relocatable kdump kernel
  powerpc: Don't use a 16G page if beyond mem= limits
  powerpc: Add del_node() for early boot code to prune inapplicable devices.
  powerpc: Further compile fixup for STRICT_MM_TYPECHECKS
  powerpc: Remove empty #else from signal_64.c
  powerpc: Move memory size print into common show_cpuinfo for 32-bit
  hvc_console: Remove __devexit annotation of hvc_remove()
  hvc_console: Add support for tty window resizing
  hvc_console: Fix loop if put_char() returns 0
  hvc_console: Add tty driver flag TTY_DRIVER_RESET_TERMIOS
  hvc_console: Add a hangup notifier for backends
  powerpc/83xx: Add DS1339 RTC support for MPC8349E-mITX boards .dts
  powerpc/83xx: Add support for MCU microcontroller in .dts files
  powerpc/85xx: Move mpc8572ds.dts to address-cells/size-cells = <2>
  of/spi: Support specifying chip select as active high via device tree
  powerpc: Remove device_type = "board_control" properties in .dts files
  i2c-cpm: Suppress autoprobing for devices
  powerpc/85xx: Fix mpc8536ds dma interrupt numbers
  powerpc/85xx: Enable enhanced functions for 8536 TSEC
  powerpc: Delete unused prom_strtoul and prom_memparse
  ...

Documentation/kdump/kdump.txt

@@ -109,7 +109,8 @@ There are two possible methods of using Kdump.
 2) Or use the system kernel binary itself as dump-capture kernel and there is
    no need to build a separate dump-capture kernel. This is possible
    only with the architecutres which support a relocatable kernel. As
-   of today, i386, x86_64 and ia64 architectures support relocatable kernel.
+   of today, i386, x86_64, ppc64 and ia64 architectures support relocatable
+   kernel.
 
 Building a relocatable kernel is advantageous from the point of view that
 one does not have to build a second kernel for capturing the dump. But
@@ -207,8 +208,15 @@ Dump-capture kernel config options (Arch Dependent, i386 and x86_64)
 Dump-capture kernel config options (Arch Dependent, ppc64)
 ----------------------------------------------------------
 
-*  Make and install the kernel and its modules. DO NOT add this kernel
-   to the boot loader configuration files.
+1) Enable "Build a kdump crash kernel" support under "Kernel" options:
+
+   CONFIG_CRASH_DUMP=y
+
+2)   Enable "Build a relocatable kernel" support
+
+   CONFIG_RELOCATABLE=y
+
+   Make and install the kernel and its modules.
 
 Dump-capture kernel config options (Arch Dependent, ia64)
 ----------------------------------------------------------

Documentation/powerpc/booting-without-of.txt

@@ -1917,6 +1917,8 @@ platforms are moved over to use the flattened-device-tree model.
 			inverse clock polarity (CPOL) mode
     - spi-cpha        - (optional) Empty property indicating device requires
 			shifted clock phase (CPHA) mode
+    - spi-cs-high     - (optional) Empty property indicating device requires
+			chip select active high
 
     SPI example for an MPC5200 SPI bus:
 		spi@f00 {

Documentation/powerpc/dts-bindings/fsl/board.txt

@@ -2,13 +2,13 @@
 
 Required properties:
 
- - device_type : Should be "board-control"
+ - compatible : Should be "fsl,<board>-bcsr"
  - reg : Offset and length of the register set for the device
 
 Example:
 
 	bcsr@f8000000 {
-		device_type = "board-control";
+		compatible = "fsl,mpc8360mds-bcsr";
 		reg = <f8000000 8000>;
 	};
 

arch/powerpc/Kconfig

@@ -19,9 +19,6 @@ config WORD_SIZE
 	default 64 if PPC64
 	default 32 if !PPC64
 
-config PPC_MERGE
-	def_bool y
-
 config ARCH_PHYS_ADDR_T_64BIT
        def_bool PPC64 || PHYS_64BIT
 
@@ -326,13 +323,11 @@ config KEXEC
 
 config CRASH_DUMP
 	bool "Build a kdump crash kernel"
-	depends on PPC_MULTIPLATFORM && PPC64
+	depends on PPC_MULTIPLATFORM && PPC64 && RELOCATABLE
 	help
 	  Build a kernel suitable for use as a kdump capture kernel.
-	  The kernel will be linked at a different address than normal, and
-	  so can only be used for Kdump.
-
-	  Don't change this unless you know what you are doing.
+	  The same kernel binary can be used as production kernel and dump
+	  capture kernel.
 
 config PHYP_DUMP
 	bool "Hypervisor-assisted dump (EXPERIMENTAL)"
@@ -832,11 +827,9 @@ config PAGE_OFFSET
 	default "0xc000000000000000"
 config KERNEL_START
 	hex
-	default "0xc000000002000000" if CRASH_DUMP
 	default "0xc000000000000000"
 config PHYSICAL_START
 	hex
-	default "0x02000000" if CRASH_DUMP
 	default "0x00000000"
 endif
 

arch/powerpc/boot/Makefile

@@ -68,7 +68,8 @@ src-plat := of.c cuboot-52xx.c cuboot-824x.c cuboot-83xx.c cuboot-85xx.c holly.c
 		fixed-head.S ep88xc.c ep405.c cuboot-c2k.c \
 		cuboot-katmai.c cuboot-rainier.c redboot-8xx.c ep8248e.c \
 		cuboot-warp.c cuboot-85xx-cpm2.c cuboot-yosemite.c simpleboot.c \
-		virtex405-head.S virtex.c redboot-83xx.c cuboot-sam440ep.c
+		virtex405-head.S virtex.c redboot-83xx.c cuboot-sam440ep.c \
+		cuboot-acadia.c
 src-boot := $(src-wlib) $(src-plat) empty.c
 
 src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -211,6 +212,7 @@ image-$(CONFIG_DEFAULT_UIMAGE)		+= uImage
 # Board ports in arch/powerpc/platform/40x/Kconfig
 image-$(CONFIG_EP405)			+= dtbImage.ep405
 image-$(CONFIG_WALNUT)			+= treeImage.walnut
+image-$(CONFIG_ACADIA)			+= cuImage.acadia
 
 # Board ports in arch/powerpc/platform/44x/Kconfig
 image-$(CONFIG_EBONY)			+= treeImage.ebony cuImage.ebony
@@ -319,6 +321,9 @@ $(obj)/zImage.iseries: vmlinux
 $(obj)/uImage: vmlinux $(wrapperbits)
 	$(call if_changed,wrap,uboot)
 
+$(obj)/cuImage.initrd.%: vmlinux $(obj)/%.dtb $(wrapperbits)
+	$(call if_changed,wrap,cuboot-$*,,$(obj)/$*.dtb,$(obj)/ramdisk.image.gz)
+
 $(obj)/cuImage.%: vmlinux $(obj)/%.dtb $(wrapperbits)
 	$(call if_changed,wrap,cuboot-$*,,$(obj)/$*.dtb)
 

arch/powerpc/boot/addnote.c

@@ -11,7 +11,7 @@
  * as published by the Free Software Foundation; either version
  * 2 of the License, or (at your option) any later version.
  *
- * Usage: addnote zImage [note.elf]
+ * Usage: addnote [-r realbase] zImage [note.elf]
  *
  * If note.elf is supplied, it is the name of an ELF file that contains
  * an RPA note to use instead of the built-in one.  Alternatively, the
@@ -153,18 +153,31 @@ unsigned char *read_rpanote(const char *fname, int *nnp)
 int
 main(int ac, char **av)
 {
-	int fd, n, i;
+	int fd, n, i, ai;
 	int ph, ps, np;
 	int nnote, nnote2, ns;
 	unsigned char *rpap;
-
-	if (ac != 2 && ac != 3) {
-		fprintf(stderr, "Usage: %s elf-file [rpanote.elf]\n", av[0]);
+	char *p, *endp;
+
+	ai = 1;
+	if (ac >= ai + 2 && strcmp(av[ai], "-r") == 0) {
+		/* process -r realbase */
+		p = av[ai + 1];
+		descr[1] = strtol(p, &endp, 16);
+		if (endp == p || *endp != 0) {
+			fprintf(stderr, "Can't parse -r argument '%s' as hex\n",
+				p);
+			exit(1);
+		}
+		ai += 2;
+	}
+	if (ac != ai + 1 && ac != ai + 2) {
+		fprintf(stderr, "Usage: %s [-r realbase] elf-file [rpanote.elf]\n", av[0]);
 		exit(1);
 	}
-	fd = open(av[1], O_RDWR);
+	fd = open(av[ai], O_RDWR);
 	if (fd < 0) {
-		perror(av[1]);
+		perror(av[ai]);
 		exit(1);
 	}
 
@@ -184,12 +197,12 @@ main(int ac, char **av)
 	if (buf[E_IDENT+EI_CLASS] != ELFCLASS32
 	    || buf[E_IDENT+EI_DATA] != ELFDATA2MSB) {
 		fprintf(stderr, "%s is not a big-endian 32-bit ELF image\n",
-			av[1]);
+			av[ai]);
 		exit(1);
 	}
 
-	if (ac == 3)
-		rpap = read_rpanote(av[2], &nnote2);
+	if (ac == ai + 2)
+		rpap = read_rpanote(av[ai + 1], &nnote2);
 
 	ph = GET_32BE(buf, E_PHOFF);
 	ps = GET_16BE(buf, E_PHENTSIZE);
@@ -202,7 +215,7 @@ main(int ac, char **av)
 	for (i = 0; i < np; ++i) {
 		if (GET_32BE(buf, ph + PH_TYPE) == PT_NOTE) {
 			fprintf(stderr, "%s already has a note entry\n",
-				av[1]);
+				av[ai]);
 			exit(0);
 		}
 		ph += ps;
@@ -260,18 +273,18 @@ main(int ac, char **av)
 		exit(1);
 	}
 	if (i < n) {
-		fprintf(stderr, "%s: write truncated\n", av[1]);
+		fprintf(stderr, "%s: write truncated\n", av[ai]);
 		exit(1);
 	}
 
 	exit(0);
 
  notelf:
-	fprintf(stderr, "%s does not appear to be an ELF file\n", av[1]);
+	fprintf(stderr, "%s does not appear to be an ELF file\n", av[ai]);
 	exit(1);
 
  nospace:
 	fprintf(stderr, "sorry, I can't find space in %s to put the note\n",
-		av[1]);
+		av[ai]);
 	exit(1);
 }

arch/powerpc/boot/cuboot-52xx.c

@@ -37,6 +37,10 @@ static void platform_fixups(void)
 	 * this can do a simple path lookup.
 	 */
 	soc = find_node_by_devtype(NULL, "soc");
+	if (!soc)
+		soc = find_node_by_compatible(NULL, "fsl,mpc5200-immr");
+	if (!soc)
+		soc = find_node_by_compatible(NULL, "fsl,mpc5200b-immr");
 	if (soc) {
 		setprop(soc, "bus-frequency", &bd.bi_ipbfreq,
 			sizeof(bd.bi_ipbfreq));

arch/powerpc/boot/cuboot-acadia.c

+/*
+ * Old U-boot compatibility for Acadia
+ *
+ * Author: Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * Copyright 2008 IBM Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "io.h"
+#include "dcr.h"
+#include "stdio.h"
+#include "4xx.h"
+#include "44x.h"
+#include "cuboot.h"
+
+#define TARGET_4xx
+#include "ppcboot.h"
+
+static bd_t bd;
+
+#define CPR_PERD0_SPIDV_MASK   0x000F0000     /* SPI Clock Divider */
+
+#define PLLC_SRC_MASK	       0x20000000     /* PLL feedback source */
+
+#define PLLD_FBDV_MASK	       0x1F000000     /* PLL feedback divider value */
+#define PLLD_FWDVA_MASK        0x000F0000     /* PLL forward divider A value */
+#define PLLD_FWDVB_MASK        0x00000700     /* PLL forward divider B value */
+
+#define PRIMAD_CPUDV_MASK      0x0F000000     /* CPU Clock Divisor Mask */
+#define PRIMAD_PLBDV_MASK      0x000F0000     /* PLB Clock Divisor Mask */
+#define PRIMAD_OPBDV_MASK      0x00000F00     /* OPB Clock Divisor Mask */
+#define PRIMAD_EBCDV_MASK      0x0000000F     /* EBC Clock Divisor Mask */
+
+#define PERD0_PWMDV_MASK       0xFF000000     /* PWM Divider Mask */
+#define PERD0_SPIDV_MASK       0x000F0000     /* SPI Divider Mask */
+#define PERD0_U0DV_MASK        0x0000FF00     /* UART 0 Divider Mask */
+#define PERD0_U1DV_MASK        0x000000FF     /* UART 1 Divider Mask */
+
+static void get_clocks(void)
+{
+	unsigned long sysclk, cpr_plld, cpr_pllc, cpr_primad, plloutb, i;
+	unsigned long pllFwdDiv, pllFwdDivB, pllFbkDiv, pllPlbDiv, pllExtBusDiv;
+	unsigned long pllOpbDiv, freqEBC, freqUART, freqOPB;
+	unsigned long div;		/* total divisor udiv * bdiv */
+	unsigned long umin;		/* minimum udiv	*/
+	unsigned short diff;		/* smallest diff */
+	unsigned long udiv;		/* best udiv */
+	unsigned short idiff;		/* current diff */
+	unsigned short ibdiv;		/* current bdiv */
+	unsigned long est;		/* current estimate */
+	unsigned long baud;
+	void *np;
+
+	/* read the sysclk value from the CPLD */
+	sysclk = (in_8((unsigned char *)0x80000000) == 0xc) ? 66666666 : 33333000;
+
+	/*
+	 * Read PLL Mode registers
+	 */
+	cpr_plld = CPR0_READ(DCRN_CPR0_PLLD);
+	cpr_pllc = CPR0_READ(DCRN_CPR0_PLLC);
+
+	/*
+	 * Determine forward divider A
+	 */
+	pllFwdDiv = ((cpr_plld & PLLD_FWDVA_MASK) >> 16);
+
+	/*
+	 * Determine forward divider B
+	 */
+	pllFwdDivB = ((cpr_plld & PLLD_FWDVB_MASK) >> 8);
+	if (pllFwdDivB == 0)
+		pllFwdDivB = 8;
+
+	/*
+	 * Determine FBK_DIV.
+	 */
+	pllFbkDiv = ((cpr_plld & PLLD_FBDV_MASK) >> 24);
+	if (pllFbkDiv == 0)
+		pllFbkDiv = 256;
+
+	/*
+	 * Read CPR_PRIMAD register
+	 */
+	cpr_primad = CPR0_READ(DCRN_CPR0_PRIMAD);
+
+	/*
+	 * Determine PLB_DIV.
+	 */
+	pllPlbDiv = ((cpr_primad & PRIMAD_PLBDV_MASK) >> 16);
+	if (pllPlbDiv == 0)
+		pllPlbDiv = 16;
+
+	/*
+	 * Determine EXTBUS_DIV.
+	 */
+	pllExtBusDiv = (cpr_primad & PRIMAD_EBCDV_MASK);
+	if (pllExtBusDiv == 0)
+		pllExtBusDiv = 16;
+
+	/*
+	 * Determine OPB_DIV.
+	 */
+	pllOpbDiv = ((cpr_primad & PRIMAD_OPBDV_MASK) >> 8);
+	if (pllOpbDiv == 0)
+		pllOpbDiv = 16;
+
+	/* There is a bug in U-Boot that prevents us from using
+	 * bd.bi_opbfreq because U-Boot doesn't populate it for
+	 * 405EZ.  We get to calculate it, yay!
+	 */
+	freqOPB = (sysclk *pllFbkDiv) /pllOpbDiv;
+
+	freqEBC = (sysclk * pllFbkDiv) / pllExtBusDiv;
+
+	plloutb = ((sysclk * ((cpr_pllc & PLLC_SRC_MASK) ?
+					   pllFwdDivB : pllFwdDiv) *
+		    pllFbkDiv) / pllFwdDivB);
+
+	np = find_node_by_alias("serial0");
+	if (getprop(np, "current-speed", &baud, sizeof(baud)) != sizeof(baud))
+		fatal("no current-speed property\n\r");
+
+	udiv = 256;			/* Assume lowest possible serial clk */
+	div = plloutb / (16 * baud); /* total divisor */
+	umin = (plloutb / freqOPB) << 1;	/* 2 x OPB divisor */
+	diff = 256;			/* highest possible */
+
+	/* i is the test udiv value -- start with the largest
+	 * possible (256) to minimize serial clock and constrain
+	 * search to umin.
+	 */
+	for (i = 256; i > umin; i--) {
+		ibdiv = div / i;
+		est = i * ibdiv;
+		idiff = (est > div) ? (est-div) : (div-est);
+		if (idiff == 0) {
+			udiv = i;
+			break;      /* can't do better */
+		} else if (idiff < diff) {
+			udiv = i;       /* best so far */
+			diff = idiff;   /* update lowest diff*/
+		}
+	}
+	freqUART = plloutb / udiv;
+
+	dt_fixup_cpu_clocks(bd.bi_procfreq, bd.bi_intfreq, bd.bi_plb_busfreq);
+	dt_fixup_clock("/plb/ebc", freqEBC);
+	dt_fixup_clock("/plb/opb", freqOPB);
+	dt_fixup_clock("/plb/opb/serial@ef600300", freqUART);
+	dt_fixup_clock("/plb/opb/serial@ef600400", freqUART);
+}
+
+static void acadia_fixups(void)
+{
+	dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
+	get_clocks();
+	dt_fixup_mac_address_by_alias("ethernet0", bd.bi_enetaddr);
+}
+	
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+		unsigned long r6, unsigned long r7)
+{
+	CUBOOT_INIT();
+	platform_ops.fixups = acadia_fixups;
+	platform_ops.exit = ibm40x_dbcr_reset;
+	fdt_init(_dtb_start);
+	serial_console_init();
+}

arch/powerpc/boot/dts/acadia.dts

+/*
+ * Device Tree Source for AMCC Acadia (405EZ)
+ *
+ * Copyright IBM Corp. 2008
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "amcc,acadia";
+	compatible = "amcc,acadia";
+	dcr-parent = <&{/cpus/cpu@0}>;
+
+	aliases {
+		ethernet0 = &EMAC0;
+		serial0 = &UART0;
+		serial1 = &UART1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			model = "PowerPC,405EZ";
+			reg = <0x0>;
+			clock-frequency = <0>; /* Filled in by wrapper */
+			timebase-frequency = <0>; /* Filled in by wrapper */
+			i-cache-line-size = <32>;
+			d-cache-line-size = <32>;
+			i-cache-size = <16384>;
+			d-cache-size = <16384>;
+			dcr-controller;
+			dcr-access-method = "native";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x0>; /* Filled in by wrapper */
+	};
+
+	UIC0: interrupt-controller {
+		compatible = "ibm,uic-405ez", "ibm,uic";
+		interrupt-controller;
+		dcr-reg = <0x0c0 0x009>;
+		cell-index = <0>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+	};
+
+	plb {
+		compatible = "ibm,plb-405ez", "ibm,plb3";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		clock-frequency = <0>; /* Filled in by wrapper */
+
+		MAL0: mcmal {
+			compatible = "ibm,mcmal-405ez", "ibm,mcmal";
+			dcr-reg = <0x380 0x62>;
+			num-tx-chans = <1>;
+			num-rx-chans = <1>;
+			interrupt-parent = <&UIC0>;
+			/* 405EZ has only 3 interrupts to the UIC, as
+			 * SERR, TXDE, and RXDE are or'd together into
+			 * one UIC bit
+			 */
+			interrupts = <
+				0x13 0x4 /* TXEOB */
+				0x15 0x4 /* RXEOB */
+				0x12 0x4 /* SERR, TXDE, RXDE */>;
+		};
+
+		POB0: opb {
+			compatible = "ibm,opb-405ez", "ibm,opb";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			dcr-reg = <0x0a 0x05>;
+			clock-frequency = <0>; /* Filled in by wrapper */
+
+			UART0: serial@ef600300 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <0xef600300 0x8>;
+				virtual-reg = <0xef600300>;
+				clock-frequency = <0>; /* Filled in by wrapper */
+				current-speed = <115200>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <0x5 0x4>;
+			};
+
+			UART1: serial@ef600400 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <0xef600400 0x8>;
+				clock-frequency = <0>; /* Filled in by wrapper */
+				current-speed = <115200>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <0x6 0x4>;
+			};
+
+			IIC: i2c@ef600500 {
+				compatible = "ibm,iic-405ez", "ibm,iic";
+				reg = <0xef600500 0x11>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <0xa 0x4>;
+			};
+
+			GPIO0: gpio@ef600700 {
+				compatible = "ibm,gpio-405ez";
+				reg = <0xef600700 0x20>;
+			};
+
+			GPIO1: gpio@ef600800 {
+				compatible = "ibm,gpio-405ez";
+				reg = <0xef600800 0x20>;
+			};
+
+			EMAC0: ethernet@ef600900 {
+				device_type = "network";
+				compatible = "ibm,emac-405ez", "ibm,emac";
+				interrupt-parent = <&UIC0>;
+				interrupts = <
+					0x10 0x4 /* Ethernet */
+					0x11 0x4 /* Ethernet Wake up */>;
+				local-mac-address = [000000000000]; /* Filled in by wrapper */
+				reg = <0xef600900 0x70>;
+				mal-device = <&MAL0>;
+				mal-tx-channel = <0>;
+				mal-rx-channel = <0>;
+				cell-index = <0>;
+				max-frame-size = <1500>;
+				rx-fifo-size = <4096>;
+				tx-fifo-size = <2048>;
+				phy-mode = "mii";
+				phy-map = <0x0>;
+			};
+
+			CAN0: can@ef601000 {
+				compatible = "amcc,can-405ez";
+				reg = <0xef601000 0x620>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <0x7 0x4>;
+			};
+
+			CAN1: can@ef601800 {
+				compatible = "amcc,can-405ez";
+				reg = <0xef601800 0x620>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <0x8 0x4>;
+			};
+
+			cameleon@ef602000 {
+				compatible = "amcc,cameleon-405ez";
+				reg = <0xef602000 0x800>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <0xb 0x4 0xc 0x4>;
+			};
+
+			ieee1588@ef602800 {
+				compatible = "amcc,ieee1588-405ez";
+				reg = <0xef602800 0x60>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <0x4 0x4>;
+				/* This thing is a bit weird.  It has it's own UIC
+				 * that it uses to generate snapshot triggers.  We
+				 * don't really support this device yet, and it needs
+				 * work to figure this out.
+				 */
+				dcr-reg = <0xe0 0x9>;
+			};
+
+			usb@ef603000 {
+				compatible = "ohci-be";
+				reg = <0xef603000 0x80>;
+				interrupts-parent = <&UIC0>;
+				interrupts = <0xd 0x4 0xe 0x4>;
+			};
+
+			dac@ef603300 {
+				compatible = "amcc,dac-405ez";
+				reg = <0xef603300 0x40>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <0x18 0x4>;
+			};
+
+			adc@ef603400 {
+				compatible = "amcc,adc-405ez";
+				reg = <0xef603400 0x40>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <0x17 0x4>;
+			};
+
+			spi@ef603500 {
+				compatible = "amcc,spi-405ez";
+				reg = <0xef603500 0x100>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <0x9 0x4>;
+			};
+		};
+
+		EBC0: ebc {
+			compatible = "ibm,ebc-405ez", "ibm,ebc";
+			dcr-reg = <0x12 0x2>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			clock-frequency = <0>; /* Filled in by wrapper */
+		};
+	};
+
+	chosen {
+		linux,stdout-path = "/plb/opb/serial@ef600300";
+	};
+};

arch/powerpc/boot/dts/hcu4.dts

+/*
+* Device Tree Source for Netstal Maschinen HCU4
+* based on the IBM Walnut
+*
+* Copyright 2008
+* Niklaus Giger <niklaus.giger@member.fsf.org>
+*
+* Copyright 2007 IBM Corp.
+* Josh Boyer <jwboyer@linux.vnet.ibm.com>
+*
+* This file is licensed under the terms of the GNU General Public
+* License version 2.  This program is licensed "as is" without
+* any warranty of any kind, whether express or implied.
+*/
+
+/dts-v1/;
+
+/ {
+	#address-cells = <0x1>;
+	#size-cells = <0x1>;
+	model = "netstal,hcu4";
+	compatible = "netstal,hcu4";
+	dcr-parent = <0x1>;
+
+	aliases {
+		ethernet0 = "/plb/opb/ethernet@ef600800";
+		serial0 = "/plb/opb/serial@ef600300";
+	};
+
+	cpus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			model = "PowerPC,405GPr";
+			reg = <0x0>;
+			clock-frequency = <0>;		/* Filled in by U-Boot */
+			timebase-frequency = <0x0>;	/* Filled in by U-Boot */
+			i-cache-line-size = <0x20>;
+			d-cache-line-size = <0x20>;
+			i-cache-size = <0x4000>;
+			d-cache-size = <0x4000>;
+			dcr-controller;
+			dcr-access-method = "native";
+			linux,phandle = <0x1>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x0>;	/* Filled in by U-Boot */
+	};
+
+	UIC0: interrupt-controller {
+		compatible = "ibm,uic";
+		interrupt-controller;
+		cell-index = <0x0>;
+		dcr-reg = <0xc0 0x9>;
+		#address-cells = <0x0>;
+		#size-cells = <0x0>;
+		#interrupt-cells = <0x2>;
+		linux,phandle = <0x2>;
+	};
+
+	plb {
+		compatible = "ibm,plb3";
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		ranges;
+		clock-frequency = <0x0>;	/* Filled in by U-Boot */
+
+		SDRAM0: memory-controller {
+			compatible = "ibm,sdram-405gp";
+			dcr-reg = <0x10 0x2>;
+		};
+
+		MAL: mcmal {
+			compatible = "ibm,mcmal-405gp", "ibm,mcmal";
+			dcr-reg = <0x180 0x62>;
+			num-tx-chans = <0x1>;
+			num-rx-chans = <0x1>;
+			interrupt-parent = <0x2>;
+			interrupts = <0xb 0x4 0xc 0x4 0xa 0x4 0xd 0x4 0xe 0x4>;
+			linux,phandle = <0x3>;
+		};
+
+		POB0: opb {
+			compatible = "ibm,opb-405gp", "ibm,opb";
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			ranges = <0xef600000 0xef600000 0xa00000>;
+			dcr-reg = <0xa0 0x5>;
+			clock-frequency = <0x0>;	/* Filled in by U-Boot */
+
+			UART0: serial@ef600300 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <0xef600300 0x8>;
+				virtual-reg = <0xef600300>;
+				clock-frequency = <0x0>;/* Filled in by U-Boot */
+				current-speed = <0>;	/* Filled in by U-Boot */
+				interrupt-parent = <0x2>;
+				interrupts = <0x0 0x4>;
+			};
+
+			IIC: i2c@ef600500 {
+				compatible = "ibm,iic-405gp", "ibm,iic";
+				reg = <0xef600500 0x11>;
+				interrupt-parent = <0x2>;
+				interrupts = <0x2 0x4>;
+			};
+
+			GPIO: gpio@ef600700 {
+				compatible = "ibm,gpio-405gp";
+				reg = <0xef600700 0x20>;
+			};
+
+			EMAC: ethernet@ef600800 {
+				device_type = "network";
+				compatible = "ibm,emac-405gp", "ibm,emac";
+				interrupt-parent = <0x2>;
+				interrupts = <0xf 0x4 0x9 0x4>;
+				local-mac-address = [00 00 00 00 00 00];
+				reg = <0xef600800 0x70>;
+				mal-device = <0x3>;
+				mal-tx-channel = <0x0>;
+				mal-rx-channel = <0x0>;
+				cell-index = <0x0>;
+				max-frame-size = <0x5dc>;
+				rx-fifo-size = <0x1000>;
+				tx-fifo-size = <0x800>;
+				phy-mode = "rmii";
+				phy-map = <0x1>;
+			};
+		};
+
+		EBC0: ebc {
+			compatible = "ibm,ebc-405gp", "ibm,ebc";
+			dcr-reg = <0x12 0x2>;
+			#address-cells = <0x2>;
+			#size-cells = <0x1>;
+			clock-frequency = <0x0>;	/* Filled in by U-Boot */
+
+			sram@0,0 {
+				reg = <0x0 0x0 0x80000>;
+			};
+
+			flash@0,80000 {
+				compatible = "jedec-flash";
+				bank-width = <0x1>;
+				reg = <0x0 0x80000 0x80000>;
+				#address-cells = <0x1>;
+				#size-cells = <0x1>;
+
+				partition@0 {
+					label = "OpenBIOS";
+					reg = <0x0 0x80000>;
+					read-only;
+				};
+			};
+		};
+	};
+
+	chosen {
+		linux,stdout-path = "/plb/opb/serial@ef600300";
+	};
+};

arch/powerpc/boot/dts/mpc8315erdb.dts

@@ -121,6 +121,14 @@ rtc@68 {
 				compatible = "dallas,ds1339";
 				reg = <0x68>;
 			};
+
+			mcu_pio: mcu@a {
+				#gpio-cells = <2>;
+				compatible = "fsl,mc9s08qg8-mpc8315erdb",
+					     "fsl,mcu-mpc8349emitx";
+				reg = <0x0a>;
+				gpio-controller;
+			};
 		};
 
 		spi@7000 {

arch/powerpc/boot/dts/mpc832x_mds.dts

@@ -60,7 +60,7 @@ memory {
 	};
 
 	bcsr@f8000000 {
-		device_type = "board-control";
+		compatible = "fsl,mpc8323mds-bcsr";
 		reg = <0xf8000000 0x8000>;
 	};
 

arch/powerpc/boot/dts/mpc8349emitx.dts

@@ -83,6 +83,14 @@ i2c@3100 {
 			interrupts = <15 0x8>;
 			interrupt-parent = <&ipic>;
 			dfsrr;
+
+			rtc@68 {
+				device_type = "rtc";
+				compatible = "dallas,ds1339";
+				reg = <0x68>;
+				interrupts = <18 0x8>;
+				interrupt-parent = <&ipic>;
+			};
 		};
 
 		spi@7000 {
@@ -131,6 +139,14 @@ dma-channel@180 {
 				interrupt-parent = <&ipic>;
 				interrupts = <71 8>;
 			};
+
+			mcu_pio: mcu@a {
+				#gpio-cells = <2>;
+				compatible = "fsl,mc9s08qg8-mpc8349emitx",
+					     "fsl,mcu-mpc8349emitx";
+				reg = <0x0a>;
+				gpio-controller;
+			};
 		};
 
 		usb@22000 {

arch/powerpc/boot/dts/mpc8349emitxgp.dts

@@ -81,6 +81,14 @@ i2c@3100 {
 			interrupts = <15 0x8>;
 			interrupt-parent = <&ipic>;
 			dfsrr;
+
+			rtc@68 {
+				device_type = "rtc";
+				compatible = "dallas,ds1339";
+				reg = <0x68>;
+				interrupts = <18 0x8>;
+				interrupt-parent = <&ipic>;
+			};
 		};
 
 		spi@7000 {

arch/powerpc/boot/dts/mpc834x_mds.dts

@@ -49,7 +49,7 @@ memory {
 	};
 
 	bcsr@e2400000 {
-		device_type = "board-control";
+		compatible = "fsl,mpc8349mds-bcsr";
 		reg = <0xe2400000 0x8000>;
 	};
 

arch/powerpc/boot/dts/mpc836x_mds.dts

@@ -69,7 +69,7 @@ flash@0,0 {
 		};
 
 		bcsr@1,0 {
-			device_type = "board-control";
+ 			compatible = "fsl,mpc8360mds-bcsr";
 			reg = <1 0 0x8000>;
 		};
 	};

arch/powerpc/boot/dts/mpc8377_rdb.dts

@@ -121,6 +121,14 @@ rtc@68 {
 				compatible = "dallas,ds1339";
 				reg = <0x68>;
 			};
+
+			mcu_pio: mcu@a {
+				#gpio-cells = <2>;
+				compatible = "fsl,mc9s08qg8-mpc8377erdb",
+					     "fsl,mcu-mpc8349emitx";
+				reg = <0x0a>;
+				gpio-controller;
+			};
 		};
 
 		i2c@3100 {

arch/powerpc/boot/dts/mpc8378_rdb.dts

@@ -121,6 +121,14 @@ rtc@68 {
 				compatible = "dallas,ds1339";
 				reg = <0x68>;
 			};
+
+			mcu_pio: mcu@a {
+				#gpio-cells = <2>;
+				compatible = "fsl,mc9s08qg8-mpc8378erdb",
+					     "fsl,mcu-mpc8349emitx";
+				reg = <0x0a>;
+				gpio-controller;
+			};
 		};
 
 		i2c@3100 {

arch/powerpc/boot/dts/mpc8379_rdb.dts

@@ -121,6 +121,14 @@ rtc@68 {
 				compatible = "dallas,ds1339";
 				reg = <0x68>;
 			};
+
+			mcu_pio: mcu@a {
+				#gpio-cells = <2>;
+				compatible = "fsl,mc9s08qg8-mpc8379erdb",
+					     "fsl,mcu-mpc8349emitx";
+				reg = <0x0a>;
+				gpio-controller;
+			};
 		};
 
 		i2c@3100 {

arch/powerpc/boot/dts/mpc8536ds.dts

@@ -109,7 +109,7 @@ dma-channel@0 {
 				reg = <0x0 0x80>;
 				cell-index = <0>;
 				interrupt-parent = <&mpic>;
-				interrupts = <14 0x2>;
+				interrupts = <20 2>;
 			};
 			dma-channel@80 {
 				compatible = "fsl,mpc8536-dma-channel",
@@ -117,7 +117,7 @@ dma-channel@80 {
 				reg = <0x80 0x80>;
 				cell-index = <1>;
 				interrupt-parent = <&mpic>;
-				interrupts = <15 0x2>;
+				interrupts = <21 2>;
 			};
 			dma-channel@100 {
 				compatible = "fsl,mpc8536-dma-channel",
@@ -125,7 +125,7 @@ dma-channel@100 {
 				reg = <0x100 0x80>;
 				cell-index = <2>;
 				interrupt-parent = <&mpic>;
-				interrupts = <16 0x2>;
+				interrupts = <22 2>;
 			};
 			dma-channel@180 {
 				compatible = "fsl,mpc8536-dma-channel",
@@ -133,7 +133,7 @@ dma-channel@180 {
 				reg = <0x180 0x80>;
 				cell-index = <3>;
 				interrupt-parent = <&mpic>;
-				interrupts = <17 0x2>;
+				interrupts = <23 2>;
 			};
 		};
 
@@ -180,7 +180,7 @@ usb@23000 {
 		enet0: ethernet@24000 {
 			cell-index = <0>;
 			device_type = "network";
-			model = "TSEC";
+			model = "eTSEC";
 			compatible = "gianfar";
 			reg = <0x24000 0x1000>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
@@ -193,7 +193,7 @@ enet0: ethernet@24000 {
 		enet1: ethernet@26000 {
 			cell-index = <1>;
 			device_type = "network";
-			model = "TSEC";
+			model = "eTSEC";
 			compatible = "gianfar";
 			reg = <0x26000 0x1000>;
 			local-mac-address = [ 00 00 00 00 00 00 ];

arch/powerpc/boot/dts/mpc8568mds.dts

@@ -52,7 +52,7 @@ memory {
 	};
 
 	bcsr@f8000000 {
-		device_type = "board-control";
+		compatible = "fsl,mpc8568mds-bcsr";
 		reg = <0xf8000000 0x8000>;
 	};
 

arch/powerpc/boot/dts/mpc8572ds.dts

@@ -13,8 +13,8 @@
 / {
 	model = "fsl,MPC8572DS";
 	compatible = "fsl,MPC8572DS";
-	#address-cells = <1>;
-	#size-cells = <1>;
+	#address-cells = <2>;
+	#size-cells = <2>;
 
 	aliases {
 		ethernet0 = &enet0;
@@ -61,7 +61,6 @@ PowerPC,8572@1 {
 
 	memory {
 		device_type = "memory";
-		reg = <0x0 0x0>;	// Filled by U-Boot
 	};
 
 	soc8572@ffe00000 {
@@ -69,8 +68,8 @@ soc8572@ffe00000 {
 		#size-cells = <1>;
 		device_type = "soc";
 		compatible = "simple-bus";
-		ranges = <0x0 0xffe00000 0x100000>;
-		reg = <0xffe00000 0x1000>;	// CCSRBAR & soc regs, remove once parse code for immrbase fixed
+		ranges = <0x0 0 0xffe00000 0x100000>;
+		reg = <0 0xffe00000 0 0x1000>;	// CCSRBAR & soc regs, remove once parse code for immrbase fixed
 		bus-frequency = <0>;		// Filled out by uboot.
 
 		memory-controller@2000 {
@@ -351,10 +350,10 @@ pci0: pcie@ffe08000 {
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
-		reg = <0xffe08000 0x1000>;
+		reg = <0 0xffe08000 0 0x1000>;
 		bus-range = <0 255>;
-		ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
-			  0x1000000 0x0 0x0 0xffc00000 0x0 0x10000>;
+		ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
+			  0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x00010000>;
 		clock-frequency = <33333333>;
 		interrupt-parent = <&mpic>;
 		interrupts = <24 2>;
@@ -561,10 +560,10 @@ pci1: pcie@ffe09000 {
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
-		reg = <0xffe09000 0x1000>;
+		reg = <0 0xffe09000 0 0x1000>;
 		bus-range = <0 255>;
-		ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
-			  0x1000000 0x0 0x0 0xffc10000 0x0 0x10000>;
+		ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
+			  0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x00010000>;
 		clock-frequency = <33333333>;
 		interrupt-parent = <&mpic>;
 		interrupts = <26 2>;
@@ -598,10 +597,10 @@ pci2: pcie@ffe0a000 {
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
-		reg = <0xffe0a000 0x1000>;
+		reg = <0 0xffe0a000 0 0x1000>;
 		bus-range = <0 255>;
-		ranges = <0x2000000 0x0 0xc0000000 0xc0000000 0x0 0x20000000
-			  0x1000000 0x0 0x0 0xffc20000 0x0 0x10000>;
+		ranges = <0x2000000 0x0 0xc0000000 0 0xc0000000 0x0 0x20000000
+			  0x1000000 0x0 0x00000000 0 0xffc20000 0x0 0x00010000>;
 		clock-frequency = <33333333>;
 		interrupt-parent = <&mpic>;
 		interrupts = <27 2>;

arch/powerpc/boot/libfdt-wrapper.c

@@ -105,6 +105,11 @@ static int fdt_wrapper_setprop(const void *devp, const char *name,
 	return check_err(rc);
 }
 
+static int fdt_wrapper_del_node(const void *devp)
+{
+	return fdt_del_node(fdt, devp_offset(devp));
+}
+
 static void *fdt_wrapper_get_parent(const void *devp)
 {
 	return offset_devp(fdt_parent_offset(fdt, devp_offset(devp)));
@@ -165,6 +170,7 @@ static unsigned long fdt_wrapper_finalize(void)
 void fdt_init(void *blob)
 {
 	int err;
+	int bufsize;
 
 	dt_ops.finddevice = fdt_wrapper_finddevice;
 	dt_ops.getprop = fdt_wrapper_getprop;
@@ -173,21 +179,21 @@ void fdt_init(void *blob)
 	dt_ops.create_node = fdt_wrapper_create_node;
 	dt_ops.find_node_by_prop_value = fdt_wrapper_find_node_by_prop_value;
 	dt_ops.find_node_by_compatible = fdt_wrapper_find_node_by_compatible;
+	dt_ops.del_node = fdt_wrapper_del_node;
 	dt_ops.get_path = fdt_wrapper_get_path;
 	dt_ops.finalize = fdt_wrapper_finalize;
 
 	/* Make sure the dt blob is the right version and so forth */
 	fdt = blob;
-	err = fdt_open_into(fdt, fdt, fdt_totalsize(blob));
-	if (err == -FDT_ERR_NOSPACE) {
-		int bufsize = fdt_totalsize(fdt) + 4;
+	bufsize = fdt_totalsize(fdt) + 4;
 	buf = malloc(bufsize);
+	if(!buf)
+		fatal("malloc failed. can't relocate the device tree\n\r");
+
 	err = fdt_open_into(fdt, buf, bufsize);
-	}
 
 	if (err != 0)
 		fatal("fdt_init(): %s\n\r", fdt_strerror(err));
 
-	if (buf)
 	fdt = buf;
 }

arch/powerpc/boot/main.c

@@ -56,9 +56,19 @@ static struct addr_range prep_kernel(void)
 	if (platform_ops.vmlinux_alloc) {
 		addr = platform_ops.vmlinux_alloc(ei.memsize);
 	} else {
-		if ((unsigned long)_start < ei.memsize)
+		/*
+		 * Check if the kernel image (without bss) would overwrite the
+		 * bootwrapper. The device tree has been moved in fdt_init()
+		 * to an area allocated with malloc() (somewhere past _end).
+		 */
+		if ((unsigned long)_start < ei.loadsize)
 			fatal("Insufficient memory for kernel at address 0!"
-			       " (_start=%p)\n\r", _start);
+			       " (_start=%p, uncomressed size=%08x)\n\r",
+			       _start, ei.loadsize);
+
+		if ((unsigned long)_end < ei.memsize)
+			fatal("The final kernel image would overwrite the "
+					"device tree\n\r");
 	}
 
 	/* Finally, gunzip the kernel */

arch/powerpc/boot/ops.h

@@ -40,6 +40,7 @@ struct dt_ops {
 			const int buflen);
 	int	(*setprop)(const void *phandle, const char *name,
 			const void *buf, const int buflen);
+	int (*del_node)(const void *phandle);
 	void *(*get_parent)(const void *phandle);
 	/* The node must not already exist. */
 	void *(*create_node)(const void *parent, const char *name);
@@ -126,6 +127,11 @@ static inline int setprop_str(void *devp, const char *name, const char *buf)
 	return -1;
 }
 
+static inline int del_node(const void *devp)
+{
+	return dt_ops.del_node ? dt_ops.del_node(devp) : -1;
+}
+
 static inline void *get_parent(const char *devp)
 {
 	return dt_ops.get_parent ? dt_ops.get_parent(devp) : NULL;

arch/powerpc/boot/string.S

@@ -235,7 +235,7 @@ memchr:
 	.globl	memcmp
 memcmp:
 	cmpwi	0,r5,0
-	blelr
+	ble	2f
 	mtctr	r5
 	addi	r6,r3,-1
 	addi	r4,r4,-1
@@ -244,6 +244,8 @@ memcmp:
 	subf.	r3,r0,r3
 	bdnzt	2,1b
 	blr
+2:	li	r3,0
+	blr
 
 
 /*

arch/powerpc/boot/wrapper

@@ -306,11 +306,14 @@ fi
 
 # post-processing needed for some platforms
 case "$platform" in
-pseries|chrp)
+pseries)
     ${CROSS}objcopy -O binary -j .fakeelf "$kernel" "$ofile".rpanote
     $objbin/addnote "$ofile" "$ofile".rpanote
     rm -r "$ofile".rpanote
     ;;
+chrp)
+    $objbin/addnote -r c00000 "$ofile"
+    ;;
 coff)
     ${CROSS}objcopy -O aixcoff-rs6000 --set-start "$entry" "$ofile"
     $objbin/hack-coff "$ofile"

arch/powerpc/include/asm/kdump.h

@@ -9,6 +9,12 @@
  * Reserve to the end of the FWNMI area, see head_64.S */
 #define KDUMP_RESERVE_LIMIT	0x10000 /* 64K */
 
+/*
+ * Used to differentiate between relocatable kdump kernel and other
+ * kernels
+ */
+#define KDUMP_SIGNATURE	0xfeed1234
+
 #ifdef CONFIG_CRASH_DUMP
 
 #define KDUMP_TRAMPOLINE_START	0x0100
@@ -19,17 +25,18 @@
 #endif /* CONFIG_CRASH_DUMP */
 
 #ifndef __ASSEMBLY__
-#ifdef CONFIG_CRASH_DUMP
 
+extern unsigned long __kdump_flag;
+
+#if defined(CONFIG_CRASH_DUMP) && !defined(CONFIG_RELOCATABLE)
 extern void reserve_kdump_trampoline(void);
 extern void setup_kdump_trampoline(void);
-
-#else /* !CONFIG_CRASH_DUMP */
-
+#else
+/* !CRASH_DUMP || RELOCATABLE */
 static inline void reserve_kdump_trampoline(void) { ; }
 static inline void setup_kdump_trampoline(void) { ; }
+#endif
 
-#endif /* CONFIG_CRASH_DUMP */
 #endif /* __ASSEMBLY__ */
 
 #endif /* __PPC64_KDUMP_H */

arch/powerpc/include/asm/page.h

@@ -77,6 +77,7 @@
 
 #if defined(CONFIG_RELOCATABLE)
 #ifndef __ASSEMBLY__
+
 extern phys_addr_t memstart_addr;
 extern phys_addr_t kernstart_addr;
 #endif

arch/powerpc/kernel/cputable.c

@@ -1277,6 +1277,19 @@ static struct cpu_spec __initdata cpu_specs[] = {
 		.machine_check		= machine_check_4xx,
 		.platform		= "ppc405",
 	},
+	{
+		/* 405EZ */
+		.pvr_mask		= 0xffff0000,
+		.pvr_value		= 0x41510000,
+		.cpu_name		= "405EZ",
+		.cpu_features		= CPU_FTRS_40X,
+		.cpu_user_features	= PPC_FEATURE_32 |
+			PPC_FEATURE_HAS_MMU | PPC_FEATURE_HAS_4xxMAC,
+		.icache_bsize		= 32,
+		.dcache_bsize		= 32,
+		.machine_check		= machine_check_4xx,
+		.platform		= "ppc405",
+	},
 	{	/* default match */
 		.pvr_mask		= 0x00000000,
 		.pvr_value		= 0x00000000,

arch/powerpc/kernel/crash_dump.c

@@ -30,6 +30,7 @@
 /* Stores the physical address of elf header of crash image. */
 unsigned long long elfcorehdr_addr = ELFCORE_ADDR_MAX;
 
+#ifndef CONFIG_RELOCATABLE
 void __init reserve_kdump_trampoline(void)
 {
 	lmb_reserve(0, KDUMP_RESERVE_LIMIT);
@@ -68,6 +69,7 @@ void __init setup_kdump_trampoline(void)
 
 	DBG(" <- setup_kdump_trampoline()\n");
 }
+#endif /* CONFIG_RELOCATABLE */
 
 /*
  * Note: elfcorehdr_addr is not just limited to vmcore. It is also used by

arch/powerpc/kernel/head_64.S

@@ -97,6 +97,12 @@ __secondary_hold_spinloop:
 __secondary_hold_acknowledge:
 	.llong	0x0
 
+	/* This flag is set by purgatory if we should be a kdump kernel. */
+	/* Do not move this variable as purgatory knows about it. */
+	.globl	__kdump_flag
+__kdump_flag:
+	.llong	0x0
+
 #ifdef CONFIG_PPC_ISERIES
 	/*
 	 * At offset 0x20, there is a pointer to iSeries LPAR data.
@@ -1384,7 +1390,13 @@ _STATIC(__after_prom_start)
 	/* process relocations for the final address of the kernel */
 	lis	r25,PAGE_OFFSET@highest	/* compute virtual base of kernel */
 	sldi	r25,r25,32
-	mr	r3,r25
+#ifdef CONFIG_CRASH_DUMP
+	ld	r7,__kdump_flag-_stext(r26)
+	cmpldi	cr0,r7,1	/* kdump kernel ? - stay where we are */
+	bne	1f
+	add	r25,r25,r26
+#endif
+1:	mr	r3,r25
 	bl	.relocate
 #endif
 
@@ -1398,11 +1410,26 @@ _STATIC(__after_prom_start)
 	li	r3,0			/* target addr */
 	mr.	r4,r26			/* In some cases the loader may  */
 	beq	9f			/* have already put us at zero */
-	lis	r5,(copy_to_here - _stext)@ha
-	addi	r5,r5,(copy_to_here - _stext)@l /* # bytes of memory to copy */
 	li	r6,0x100		/* Start offset, the first 0x100 */
 					/* bytes were copied earlier.	 */
 
+#ifdef CONFIG_CRASH_DUMP
+/*
+ * Check if the kernel has to be running as relocatable kernel based on the
+ * variable __kdump_flag, if it is set the kernel is treated as relocatable
+ * kernel, otherwise it will be moved to PHYSICAL_START
+ */
+	ld	r7,__kdump_flag-_stext(r26)
+	cmpldi	cr0,r7,1
+	bne	3f
+
+	li	r5,__end_interrupts - _stext	/* just copy interrupts */
+	b	5f
+3:
+#endif
+	lis	r5,(copy_to_here - _stext)@ha
+	addi	r5,r5,(copy_to_here - _stext)@l /* # bytes of memory to copy */
+
 	bl	.copy_and_flush		/* copy the first n bytes	 */
 					/* this includes the code being	 */
 					/* executed here.		 */
@@ -1411,15 +1438,15 @@ _STATIC(__after_prom_start)
 	mtctr	r8
 	bctr
 
+p_end:	.llong	_end - _stext
+
 4:	/* Now copy the rest of the kernel up to _end */
 	addis	r5,r26,(p_end - _stext)@ha
 	ld	r5,(p_end - _stext)@l(r5)	/* get _end */
-	bl	.copy_and_flush		/* copy the rest */
+5:	bl	.copy_and_flush		/* copy the rest */
 
 9:	b	.start_here_multiplatform
 
-p_end:	.llong	_end - _stext
-
 /*
  * Copy routine used to copy the kernel to start at physical address 0
  * and flush and invalidate the caches as needed.

arch/powerpc/kernel/iommu.c

@@ -458,6 +458,42 @@ void iommu_unmap_sg(struct iommu_table *tbl, struct scatterlist *sglist,
 	spin_unlock_irqrestore(&(tbl->it_lock), flags);
 }
 
+static void iommu_table_clear(struct iommu_table *tbl)
+{
+	if (!__kdump_flag) {
+		/* Clear the table in case firmware left allocations in it */
+		ppc_md.tce_free(tbl, tbl->it_offset, tbl->it_size);
+		return;
+	}
+
+#ifdef CONFIG_CRASH_DUMP
+	if (ppc_md.tce_get) {
+		unsigned long index, tceval, tcecount = 0;
+
+		/* Reserve the existing mappings left by the first kernel. */
+		for (index = 0; index < tbl->it_size; index++) {
+			tceval = ppc_md.tce_get(tbl, index + tbl->it_offset);
+			/*
+			 * Freed TCE entry contains 0x7fffffffffffffff on JS20
+			 */
+			if (tceval && (tceval != 0x7fffffffffffffffUL)) {
+				__set_bit(index, tbl->it_map);
+				tcecount++;
+			}
+		}
+
+		if ((tbl->it_size - tcecount) < KDUMP_MIN_TCE_ENTRIES) {
+			printk(KERN_WARNING "TCE table is full; freeing ");
+			printk(KERN_WARNING "%d entries for the kdump boot\n",
+				KDUMP_MIN_TCE_ENTRIES);
+			for (index = tbl->it_size - KDUMP_MIN_TCE_ENTRIES;
+				index < tbl->it_size; index++)
+				__clear_bit(index, tbl->it_map);
+		}
+	}
+#endif
+}
+
 /*
  * Build a iommu_table structure.  This contains a bit map which
  * is used to manage allocation of the tce space.
@@ -484,38 +520,7 @@ struct iommu_table *iommu_init_table(struct iommu_table *tbl, int nid)
 	tbl->it_largehint = tbl->it_halfpoint;
 	spin_lock_init(&tbl->it_lock);
 
-#ifdef CONFIG_CRASH_DUMP
-	if (ppc_md.tce_get) {
-		unsigned long index;
-		unsigned long tceval;
-		unsigned long tcecount = 0;
-
-		/*
-		 * Reserve the existing mappings left by the first kernel.
-		 */
-		for (index = 0; index < tbl->it_size; index++) {
-			tceval = ppc_md.tce_get(tbl, index + tbl->it_offset);
-			/*
-			 * Freed TCE entry contains 0x7fffffffffffffff on JS20
-			 */
-			if (tceval && (tceval != 0x7fffffffffffffffUL)) {
-				__set_bit(index, tbl->it_map);
-				tcecount++;
-			}
-		}
-		if ((tbl->it_size - tcecount) < KDUMP_MIN_TCE_ENTRIES) {
-			printk(KERN_WARNING "TCE table is full; ");
-			printk(KERN_WARNING "freeing %d entries for the kdump boot\n",
-				KDUMP_MIN_TCE_ENTRIES);
-			for (index = tbl->it_size - KDUMP_MIN_TCE_ENTRIES;
-				index < tbl->it_size; index++)
-				__clear_bit(index, tbl->it_map);
-		}
-	}
-#else
-	/* Clear the hardware table in case firmware left allocations in it */
-	ppc_md.tce_free(tbl, tbl->it_offset, tbl->it_size);
-#endif
+	iommu_table_clear(tbl);
 
 	if (!welcomed) {
 		printk(KERN_INFO "IOMMU table initialized, virtual merging %s\n",

arch/powerpc/kernel/machine_kexec.c

@@ -88,11 +88,13 @@ void __init reserve_crashkernel(void)
 
 	crash_size = crashk_res.end - crashk_res.start + 1;
 
+#ifndef CONFIG_RELOCATABLE
 	if (crashk_res.start != KDUMP_KERNELBASE)
 		printk("Crash kernel location must be 0x%x\n",
 				KDUMP_KERNELBASE);
 
 	crashk_res.start = KDUMP_KERNELBASE;
+#endif
 	crash_size = PAGE_ALIGN(crash_size);
 	crashk_res.end = crashk_res.start + crash_size - 1;
 

arch/powerpc/kernel/machine_kexec_64.c

@@ -255,11 +255,14 @@ static union thread_union kexec_stack
 /* Our assembly helper, in kexec_stub.S */
 extern NORET_TYPE void kexec_sequence(void *newstack, unsigned long start,
 					void *image, void *control,
-					void (*clear_all)(void)) ATTRIB_NORET;
+					void (*clear_all)(void),
+					unsigned long kdump_flag) ATTRIB_NORET;
 
 /* too late to fail here */
 void default_machine_kexec(struct kimage *image)
 {
+	unsigned long kdump_flag = 0;
+
 	/* prepare control code if any */
 
 	/*
@@ -272,6 +275,8 @@ void default_machine_kexec(struct kimage *image)
 
 	if (crashing_cpu == -1)
 		kexec_prepare_cpus();
+	else
+		kdump_flag = KDUMP_SIGNATURE;
 
 	/* switch to a staticly allocated stack.  Based on irq stack code.
 	 * XXX: the task struct will likely be invalid once we do the copy!
@@ -284,7 +289,7 @@ void default_machine_kexec(struct kimage *image)
 	 */
 	kexec_sequence(&kexec_stack, image->start, image,
 			page_address(image->control_code_page),
-			ppc_md.hpte_clear_all);
+			ppc_md.hpte_clear_all, kdump_flag);
 	/* NOTREACHED */
 }
 
@@ -312,11 +317,24 @@ static struct property kernel_end_prop = {
 static void __init export_htab_values(void)
 {
 	struct device_node *node;
+	struct property *prop;
 
 	node = of_find_node_by_path("/chosen");
 	if (!node)
 		return;
 
+	/* remove any stale propertys so ours can be found */
+	prop = of_find_property(node, kernel_end_prop.name, NULL);
+	if (prop)
+		prom_remove_property(node, prop);
+	prop = of_find_property(node, htab_base_prop.name, NULL);
+	if (prop)
+		prom_remove_property(node, prop);
+	prop = of_find_property(node, htab_size_prop.name, NULL);
+	if (prop)
+		prom_remove_property(node, prop);
+
+	/* information needed by userspace when using default_machine_kexec */
 	kernel_end = __pa(_end);
 	prom_add_property(node, &kernel_end_prop);
 

arch/powerpc/kernel/misc_64.S

@@ -611,10 +611,12 @@ real_mode:	/* assume normal blr return */
 
 
 /*
- * kexec_sequence(newstack, start, image, control, clear_all())
+ * kexec_sequence(newstack, start, image, control, clear_all(), kdump_flag)
  *
  * does the grungy work with stack switching and real mode switches
  * also does simple calls to other code
+ *
+ * kdump_flag says whether the next kernel should be a kdump kernel.
  */
 
 _GLOBAL(kexec_sequence)
@@ -647,7 +649,7 @@ _GLOBAL(kexec_sequence)
 	mr	r29,r5			/* image (virt) */
 	mr	r28,r6			/* control, unused */
 	mr	r27,r7			/* clear_all() fn desc */
-	mr	r26,r8			/* spare */
+	mr	r26,r8			/* kdump flag */
 	lhz	r25,PACAHWCPUID(r13)	/* get our phys cpu from paca */
 
 	/* disable interrupts, we are overwriting kernel data next */
@@ -709,5 +711,6 @@ _GLOBAL(kexec_sequence)
 	mr	r4,r30	# start, aka phys mem offset
 	mtlr	4
 	li	r5,0
-	blr	/* image->start(physid, image->start, 0); */
+	mr	r6,r26			/* kdump_flag */
+	blr	/* image->start(physid, image->start, 0, kdump_flag); */
 #endif /* CONFIG_KEXEC */

arch/powerpc/kernel/pci-common.c

@@ -610,7 +610,8 @@ int pci_mmap_legacy_page_range(struct pci_bus *bus,
 	pr_debug(" -> mapping phys %llx\n", (unsigned long long)offset);
 
 	vma->vm_pgoff = offset >> PAGE_SHIFT;
-	vma->vm_page_prot |= _PAGE_NO_CACHE | _PAGE_GUARDED;
+	vma->vm_page_prot = __pgprot(pgprot_val(vma->vm_page_prot)
+				     | _PAGE_NO_CACHE | _PAGE_GUARDED);
 	return remap_pfn_range(vma, vma->vm_start, vma->vm_pgoff,
 			       vma->vm_end - vma->vm_start,
 			       vma->vm_page_prot);

arch/powerpc/kernel/prom_init.c

@@ -487,67 +487,6 @@ static int __init prom_setprop(phandle node, const char *nodename,
 	return call_prom("interpret", 1, 1, (u32)(unsigned long) cmd);
 }
 
-/* We can't use the standard versions because of RELOC headaches. */
-#define isxdigit(c)	(('0' <= (c) && (c) <= '9') \
-			 || ('a' <= (c) && (c) <= 'f') \
-			 || ('A' <= (c) && (c) <= 'F'))
-
-#define isdigit(c)	('0' <= (c) && (c) <= '9')
-#define islower(c)	('a' <= (c) && (c) <= 'z')
-#define toupper(c)	(islower(c) ? ((c) - 'a' + 'A') : (c))
-
-unsigned long prom_strtoul(const char *cp, const char **endp)
-{
-	unsigned long result = 0, base = 10, value;
-
-	if (*cp == '0') {
-		base = 8;
-		cp++;
-		if (toupper(*cp) == 'X') {
-			cp++;
-			base = 16;
-		}
-	}
-
-	while (isxdigit(*cp) &&
-	       (value = isdigit(*cp) ? *cp - '0' : toupper(*cp) - 'A' + 10) < base) {
-		result = result * base + value;
-		cp++;
-	}
-
-	if (endp)
-		*endp = cp;
-
-	return result;
-}
-
-unsigned long prom_memparse(const char *ptr, const char **retptr)
-{
-	unsigned long ret = prom_strtoul(ptr, retptr);
-	int shift = 0;
-
-	/*
-	 * We can't use a switch here because GCC *may* generate a
-	 * jump table which won't work, because we're not running at
-	 * the address we're linked at.
-	 */
-	if ('G' == **retptr || 'g' == **retptr)
-		shift = 30;
-
-	if ('M' == **retptr || 'm' == **retptr)
-		shift = 20;
-
-	if ('K' == **retptr || 'k' == **retptr)
-		shift = 10;
-
-	if (shift) {
-		ret <<= shift;
-		(*retptr)++;
-	}
-
-	return ret;
-}
-
 /*
  * Early parsing of the command line passed to the kernel, used for
  * "mem=x" and the options that affect the iommu

arch/powerpc/kernel/prom_init_check.sh

@@ -20,7 +20,7 @@ WHITELIST="add_reloc_offset __bss_start __bss_stop copy_and_flush
 _end enter_prom memcpy memset reloc_offset __secondary_hold
 __secondary_hold_acknowledge __secondary_hold_spinloop __start
 strcmp strcpy strlcpy strlen strncmp strstr logo_linux_clut224
-reloc_got2 kernstart_addr"
+reloc_got2 kernstart_addr memstart_addr"
 
 NM="$1"
 OBJ="$2"

arch/powerpc/kernel/setup-common.c

@@ -59,6 +59,7 @@
 #include <asm/mmu.h>
 #include <asm/xmon.h>
 #include <asm/cputhreads.h>
+#include <mm/mmu_decl.h>
 
 #include "setup.h"
 
@@ -190,6 +191,12 @@ static int show_cpuinfo(struct seq_file *m, void *v)
 		if (ppc_md.show_cpuinfo != NULL)
 			ppc_md.show_cpuinfo(m);
 
+#ifdef CONFIG_PPC32
+		/* Display the amount of memory */
+		seq_printf(m, "Memory\t\t: %d MB\n",
+			   (unsigned int)(total_memory / (1024 * 1024)));
+#endif
+
 		return 0;
 	}
 

arch/powerpc/kernel/signal_64.c

@@ -235,8 +235,6 @@ static long restore_sigcontext(struct pt_regs *regs, sigset_t *set, int sig,
 	else
 		for (i = 0; i < 32 ; i++)
 			current->thread.fpr[i][TS_VSRLOWOFFSET] = 0;
-
-#else
 #endif
 	return err;
 }

arch/powerpc/kernel/udbg_16550.c

@@ -142,7 +142,7 @@ unsigned int udbg_probe_uart_speed(void __iomem *comport, unsigned int clock)
 	speed = (clock / prescaler) / (divisor * 16);
 
 	/* sanity check */
-	if (speed < 0 || speed > (clock / 16))
+	if (speed > (clock / 16))
 		speed = 9600;
 
 	return speed;

arch/powerpc/mm/hash_utils_64.c

@@ -382,8 +382,10 @@ static int __init htab_dt_scan_hugepage_blocks(unsigned long node,
 	printk(KERN_INFO "Huge page(16GB) memory: "
 			"addr = 0x%lX size = 0x%lX pages = %d\n",
 			phys_addr, block_size, expected_pages);
+	if (phys_addr + (16 * GB) <= lmb_end_of_DRAM()) {
 		lmb_reserve(phys_addr, block_size * expected_pages);
 		add_gpage(phys_addr, block_size, expected_pages);
+	}
 	return 0;
 }
 #endif /* CONFIG_HUGETLB_PAGE */

arch/powerpc/mm/numa.c

@@ -116,6 +116,7 @@ static int __init get_active_region_work_fn(unsigned long start_pfn,
 
 /*
  * get_node_active_region - Return active region containing start_pfn
+ * Active range returned is empty if none found.
  * @start_pfn: The page to return the region for.
  * @node_ar: Returned set to the active region containing start_pfn
  */
@@ -126,6 +127,7 @@ static void __init get_node_active_region(unsigned long start_pfn,
 
 	node_ar->nid = nid;
 	node_ar->start_pfn = start_pfn;
+	node_ar->end_pfn = start_pfn;
 	work_with_active_regions(nid, get_active_region_work_fn, node_ar);
 }
 
@@ -526,12 +528,10 @@ static unsigned long __init numa_enforce_memory_limit(unsigned long start,
 	/*
 	 * We use lmb_end_of_DRAM() in here instead of memory_limit because
 	 * we've already adjusted it for the limit and it takes care of
-	 * having memory holes below the limit.
+	 * having memory holes below the limit.  Also, in the case of
+	 * iommu_is_off, memory_limit is not set but is implicitly enforced.
 	 */
 
-	if (! memory_limit)
-		return size;
-
 	if (start + size <= lmb_end_of_DRAM())
 		return size;
 
@@ -933,18 +933,20 @@ void __init do_init_bootmem(void)
 		struct node_active_region node_ar;
 
 		get_node_active_region(start_pfn, &node_ar);
-		while (start_pfn < end_pfn) {
+		while (start_pfn < end_pfn &&
+			node_ar.start_pfn < node_ar.end_pfn) {
+			unsigned long reserve_size = size;
 			/*
 			 * if reserved region extends past active region
 			 * then trim size to active region
 			 */
 			if (end_pfn > node_ar.end_pfn)
-				size = (node_ar.end_pfn << PAGE_SHIFT)
+				reserve_size = (node_ar.end_pfn << PAGE_SHIFT)
 					- (start_pfn << PAGE_SHIFT);
-			dbg("reserve_bootmem %lx %lx nid=%d\n", physbase, size,
-				node_ar.nid);
+			dbg("reserve_bootmem %lx %lx nid=%d\n", physbase,
+				reserve_size, node_ar.nid);
 			reserve_bootmem_node(NODE_DATA(node_ar.nid), physbase,
-						size, BOOTMEM_DEFAULT);
+						reserve_size, BOOTMEM_DEFAULT);
 			/*
 			 * if reserved region is contained in the active region
 			 * then done.
@@ -959,6 +961,7 @@ void __init do_init_bootmem(void)
 			 */
 			start_pfn = node_ar.end_pfn;
 			physbase = start_pfn << PAGE_SHIFT;
+			size = size - reserve_size;
 			get_node_active_region(start_pfn, &node_ar);
 		}
 

arch/powerpc/oprofile/cell/pr_util.h

@@ -24,6 +24,11 @@
 #define SKIP_GENERIC_SYNC 0
 #define SYNC_START_ERROR -1
 #define DO_GENERIC_SYNC 1
+#define SPUS_PER_NODE   8
+#define DEFAULT_TIMER_EXPIRE  (HZ / 10)
+
+extern struct delayed_work spu_work;
+extern int spu_prof_running;
 
 struct spu_overlay_info {	/* map of sections within an SPU overlay */
 	unsigned int vma;	/* SPU virtual memory address from elf */
@@ -62,6 +67,14 @@ struct vma_to_fileoffset_map {	/* map of sections within an SPU program */
 
 };
 
+struct spu_buffer {
+	int last_guard_val;
+	int ctx_sw_seen;
+	unsigned long *buff;
+	unsigned int head, tail;
+};
+
+
 /* The three functions below are for maintaining and accessing
  * the vma-to-fileoffset map.
  */

arch/powerpc/oprofile/cell/spu_profiler.c

@@ -23,12 +23,11 @@
 
 static u32 *samples;
 
-static int spu_prof_running;
+int spu_prof_running;
 static unsigned int profiling_interval;
 
 #define NUM_SPU_BITS_TRBUF 16
 #define SPUS_PER_TB_ENTRY   4
-#define SPUS_PER_NODE	     8
 
 #define SPU_PC_MASK	     0xFFFF
 
@@ -208,6 +207,7 @@ int start_spu_profiling(unsigned int cycles_reset)
 
 	spu_prof_running = 1;
 	hrtimer_start(&timer, kt, HRTIMER_MODE_REL);
+	schedule_delayed_work(&spu_work, DEFAULT_TIMER_EXPIRE);
 
 	return 0;
 }

arch/powerpc/oprofile/cell/spu_task_sync.c

@@ -35,7 +35,102 @@ static DEFINE_SPINLOCK(buffer_lock);
 static DEFINE_SPINLOCK(cache_lock);
 static int num_spu_nodes;
 int spu_prof_num_nodes;
-int last_guard_val[MAX_NUMNODES * 8];
+
+struct spu_buffer spu_buff[MAX_NUMNODES * SPUS_PER_NODE];
+struct delayed_work spu_work;
+static unsigned max_spu_buff;
+
+static void spu_buff_add(unsigned long int value, int spu)
+{
+	/* spu buff is a circular buffer.  Add entries to the
+	 * head.  Head is the index to store the next value.
+	 * The buffer is full when there is one available entry
+	 * in the queue, i.e. head and tail can't be equal.
+	 * That way we can tell the difference between the
+	 * buffer being full versus empty.
+	 *
+	 *  ASSUPTION: the buffer_lock is held when this function
+	 *             is called to lock the buffer, head and tail.
+	 */
+	int full = 1;
+
+	if (spu_buff[spu].head >= spu_buff[spu].tail) {
+		if ((spu_buff[spu].head - spu_buff[spu].tail)
+		    <  (max_spu_buff - 1))
+			full = 0;
+
+	} else if (spu_buff[spu].tail > spu_buff[spu].head) {
+		if ((spu_buff[spu].tail - spu_buff[spu].head)
+		    > 1)
+			full = 0;
+	}
+
+	if (!full) {
+		spu_buff[spu].buff[spu_buff[spu].head] = value;
+		spu_buff[spu].head++;
+
+		if (spu_buff[spu].head >= max_spu_buff)
+			spu_buff[spu].head = 0;
+	} else {
+		/* From the user's perspective make the SPU buffer
+		 * size management/overflow look like we are using
+		 * per cpu buffers.  The user uses the same
+		 * per cpu parameter to adjust the SPU buffer size.
+		 * Increment the sample_lost_overflow to inform
+		 * the user the buffer size needs to be increased.
+		 */
+		oprofile_cpu_buffer_inc_smpl_lost();
+	}
+}
+
+/* This function copies the per SPU buffers to the
+ * OProfile kernel buffer.
+ */
+void sync_spu_buff(void)
+{
+	int spu;
+	unsigned long flags;
+	int curr_head;
+
+	for (spu = 0; spu < num_spu_nodes; spu++) {
+		/* In case there was an issue and the buffer didn't
+		 * get created skip it.
+		 */
+		if (spu_buff[spu].buff == NULL)
+			continue;
+
+		/* Hold the lock to make sure the head/tail
+		 * doesn't change while spu_buff_add() is
+		 * deciding if the buffer is full or not.
+		 * Being a little paranoid.
+		 */
+		spin_lock_irqsave(&buffer_lock, flags);
+		curr_head = spu_buff[spu].head;
+		spin_unlock_irqrestore(&buffer_lock, flags);
+
+		/* Transfer the current contents to the kernel buffer.
+		 * data can still be added to the head of the buffer.
+		 */
+		oprofile_put_buff(spu_buff[spu].buff,
+				  spu_buff[spu].tail,
+				  curr_head, max_spu_buff);
+
+		spin_lock_irqsave(&buffer_lock, flags);
+		spu_buff[spu].tail = curr_head;
+		spin_unlock_irqrestore(&buffer_lock, flags);
+	}
+
+}
+
+static void wq_sync_spu_buff(struct work_struct *work)
+{
+	/* move data from spu buffers to kernel buffer */
+	sync_spu_buff();
+
+	/* only reschedule if profiling is not done */
+	if (spu_prof_running)
+		schedule_delayed_work(&spu_work, DEFAULT_TIMER_EXPIRE);
+}
 
 /* Container for caching information about an active SPU task. */
 struct cached_info {
@@ -305,14 +400,21 @@ static int process_context_switch(struct spu *spu, unsigned long objectId)
 
 	/* Record context info in event buffer */
 	spin_lock_irqsave(&buffer_lock, flags);
-	add_event_entry(ESCAPE_CODE);
-	add_event_entry(SPU_CTX_SWITCH_CODE);
-	add_event_entry(spu->number);
-	add_event_entry(spu->pid);
-	add_event_entry(spu->tgid);
-	add_event_entry(app_dcookie);
-	add_event_entry(spu_cookie);
-	add_event_entry(offset);
+	spu_buff_add(ESCAPE_CODE, spu->number);
+	spu_buff_add(SPU_CTX_SWITCH_CODE, spu->number);
+	spu_buff_add(spu->number, spu->number);
+	spu_buff_add(spu->pid, spu->number);
+	spu_buff_add(spu->tgid, spu->number);
+	spu_buff_add(app_dcookie, spu->number);
+	spu_buff_add(spu_cookie, spu->number);
+	spu_buff_add(offset, spu->number);
+
+	/* Set flag to indicate SPU PC data can now be written out.  If
+	 * the SPU program counter data is seen before an SPU context
+	 * record is seen, the postprocessing will fail.
+	 */
+	spu_buff[spu->number].ctx_sw_seen = 1;
+
 	spin_unlock_irqrestore(&buffer_lock, flags);
 	smp_wmb();	/* insure spu event buffer updates are written */
 			/* don't want entries intermingled... */
@@ -360,6 +462,47 @@ static int number_of_online_nodes(void)
         return nodes;
 }
 
+static int oprofile_spu_buff_create(void)
+{
+	int spu;
+
+	max_spu_buff = oprofile_get_cpu_buffer_size();
+
+	for (spu = 0; spu < num_spu_nodes; spu++) {
+		/* create circular buffers to store the data in.
+		 * use locks to manage accessing the buffers
+		 */
+		spu_buff[spu].head = 0;
+		spu_buff[spu].tail = 0;
+
+		/*
+		 * Create a buffer for each SPU.  Can't reliably
+		 * create a single buffer for all spus due to not
+		 * enough contiguous kernel memory.
+		 */
+
+		spu_buff[spu].buff = kzalloc((max_spu_buff
+					      * sizeof(unsigned long)),
+					     GFP_KERNEL);
+
+		if (!spu_buff[spu].buff) {
+			printk(KERN_ERR "SPU_PROF: "
+			       "%s, line %d:  oprofile_spu_buff_create "
+		       "failed to allocate spu buffer %d.\n",
+			       __func__, __LINE__, spu);
+
+			/* release the spu buffers that have been allocated */
+			while (spu >= 0) {
+				kfree(spu_buff[spu].buff);
+				spu_buff[spu].buff = 0;
+				spu--;
+			}
+			return -ENOMEM;
+		}
+	}
+	return 0;
+}
+
 /* The main purpose of this function is to synchronize
  * OProfile with SPUFS by registering to be notified of
  * SPU task switches.
@@ -372,20 +515,35 @@ static int number_of_online_nodes(void)
  */
 int spu_sync_start(void)
 {
-	int k;
+	int spu;
 	int ret = SKIP_GENERIC_SYNC;
 	int register_ret;
 	unsigned long flags = 0;
 
 	spu_prof_num_nodes = number_of_online_nodes();
 	num_spu_nodes = spu_prof_num_nodes * 8;
+	INIT_DELAYED_WORK(&spu_work, wq_sync_spu_buff);
+
+	/* create buffer for storing the SPU data to put in
+	 * the kernel buffer.
+	 */
+	ret = oprofile_spu_buff_create();
+	if (ret)
+		goto out;
 
 	spin_lock_irqsave(&buffer_lock, flags);
-	add_event_entry(ESCAPE_CODE);
-	add_event_entry(SPU_PROFILING_CODE);
-	add_event_entry(num_spu_nodes);
+	for (spu = 0; spu < num_spu_nodes; spu++) {
+		spu_buff_add(ESCAPE_CODE, spu);
+		spu_buff_add(SPU_PROFILING_CODE, spu);
+		spu_buff_add(num_spu_nodes, spu);
+	}
 	spin_unlock_irqrestore(&buffer_lock, flags);
 
+	for (spu = 0; spu < num_spu_nodes; spu++) {
+		spu_buff[spu].ctx_sw_seen = 0;
+		spu_buff[spu].last_guard_val = 0;
+	}
+
 	/* Register for SPU events  */
 	register_ret = spu_switch_event_register(&spu_active);
 	if (register_ret) {
@@ -393,8 +551,6 @@ int spu_sync_start(void)
 		goto out;
 	}
 
-	for (k = 0; k < (MAX_NUMNODES * 8); k++)
-		last_guard_val[k] = 0;
 	pr_debug("spu_sync_start -- running.\n");
 out:
 	return ret;
@@ -446,13 +602,20 @@ void spu_sync_buffer(int spu_num, unsigned int *samples,
 		 * use.	 We need to discard samples taken during the time
 		 * period which an overlay occurs (i.e., guard value changes).
 		 */
-		if (grd_val && grd_val != last_guard_val[spu_num]) {
-			last_guard_val[spu_num] = grd_val;
+		if (grd_val && grd_val != spu_buff[spu_num].last_guard_val) {
+			spu_buff[spu_num].last_guard_val = grd_val;
 			/* Drop the rest of the samples. */
 			break;
 		}
 
-		add_event_entry(file_offset | spu_num_shifted);
+		/* We must ensure that the SPU context switch has been written
+		 * out before samples for the SPU.  Otherwise, the SPU context
+		 * information is not available and the postprocessing of the
+		 * SPU PC will fail with no available anonymous map information.
+		 */
+		if (spu_buff[spu_num].ctx_sw_seen)
+			spu_buff_add((file_offset | spu_num_shifted),
+					 spu_num);
 	}
 	spin_unlock(&buffer_lock);
 out:
@@ -463,20 +626,41 @@ void spu_sync_buffer(int spu_num, unsigned int *samples,
 int spu_sync_stop(void)
 {
 	unsigned long flags = 0;
-	int ret = spu_switch_event_unregister(&spu_active);
-	if (ret) {
+	int ret;
+	int k;
+
+	ret = spu_switch_event_unregister(&spu_active);
+
+	if (ret)
 		printk(KERN_ERR "SPU_PROF: "
-			"%s, line %d: spu_switch_event_unregister returned %d\n",
+		       "%s, line %d: spu_switch_event_unregister "	\
+		       "returned %d\n",
 		       __func__, __LINE__, ret);
-		goto out;
-	}
+
+	/* flush any remaining data in the per SPU buffers */
+	sync_spu_buff();
 
 	spin_lock_irqsave(&cache_lock, flags);
 	ret = release_cached_info(RELEASE_ALL);
 	spin_unlock_irqrestore(&cache_lock, flags);
-out:
+
+	/* remove scheduled work queue item rather then waiting
+	 * for every queued entry to execute.  Then flush pending
+	 * system wide buffer to event buffer.
+	 */
+	cancel_delayed_work(&spu_work);
+
+	for (k = 0; k < num_spu_nodes; k++) {
+		spu_buff[k].ctx_sw_seen = 0;
+
+		/*
+		 * spu_sys_buff will be null if there was a problem
+		 * allocating the buffer.  Only delete if it exists.
+		 */
+		kfree(spu_buff[k].buff);
+		spu_buff[k].buff = 0;
+	}
 	pr_debug("spu_sync_stop -- done.\n");
 	return ret;
 }
 
-

arch/powerpc/platforms/40x/Kconfig

@@ -14,6 +14,15 @@
 #	help
 #	  This option enables support for the CPCI405 board.
 
+config ACADIA
+	bool "Acadia"
+	depends on 40x
+	default n
+	select PPC40x_SIMPLE
+	select 405EZ
+	help
+	  This option enables support for the AMCC 405EZ Acadia evaluation board.
+
 config EP405
 	bool "EP405/EP405PC"
 	depends on 40x
@@ -23,6 +32,14 @@ config EP405
 	help
 	  This option enables support for the EP405/EP405PC boards.
 
+config HCU4
+	bool "Hcu4"
+	depends on 40x
+	default y
+	select 405GPR
+	help
+	  This option enables support for the Nestal Maschinen HCU4 board.
+
 config KILAUEA
 	bool "Kilauea"
 	depends on 40x
@@ -93,6 +110,13 @@ config XILINX_VIRTEX_GENERIC_BOARD
 	  Most Virtex designs should use this unless it needs to do some
 	  special configuration at board probe time.
 
+config PPC40x_SIMPLE
+	bool "Simple PowerPC 40x board support"
+	depends on 40x
+	default n
+	help
+	  This option enables the simple PowerPC 40x platform support.
+
 # 40x specific CPU modules, selected based on the board above.
 config NP405H
 	bool
@@ -118,6 +142,12 @@ config 405EX
 	select IBM_NEW_EMAC_EMAC4
 	select IBM_NEW_EMAC_RGMII
 
+config 405EZ
+	bool
+	select IBM_NEW_EMAC_NO_FLOW_CTRL
+	select IBM_NEW_EMAC_MAL_CLR_ICINTSTAT
+	select IBM_NEW_EMAC_MAL_COMMON_ERR
+
 config 405GPR
 	bool
 
@@ -139,6 +169,14 @@ config STB03xxx
 	select IBM405_ERR77
 	select IBM405_ERR51
 
+config PPC4xx_GPIO
+	bool "PPC4xx GPIO support"
+	depends on 40x
+	select ARCH_REQUIRE_GPIOLIB
+	select GENERIC_GPIO
+	help
+	  Enable gpiolib support for ppc40x based boards
+
 # 40x errata/workaround config symbols, selected by the CPU models above
 
 # All 405-based cores up until the 405GPR and 405EP have this errata.

arch/powerpc/platforms/40x/Makefile

 obj-$(CONFIG_KILAUEA)				+= kilauea.o
+obj-$(CONFIG_HCU4)				+= hcu4.o
 obj-$(CONFIG_MAKALU)				+= makalu.o
 obj-$(CONFIG_WALNUT)				+= walnut.o
 obj-$(CONFIG_XILINX_VIRTEX_GENERIC_BOARD)	+= virtex.o
 obj-$(CONFIG_EP405)				+= ep405.o
+obj-$(CONFIG_PPC40x_SIMPLE)		+= ppc40x_simple.o

arch/powerpc/platforms/40x/hcu4.c

+/*
+ * Architecture- / platform-specific boot-time initialization code for
+ * IBM PowerPC 4xx based boards. Adapted from original
+ * code by Gary Thomas, Cort Dougan <cort@fsmlabs.com>, and Dan Malek
+ * <dan@net4x.com>.
+ *
+ * Copyright(c) 1999-2000 Grant Erickson <grant@lcse.umn.edu>
+ *
+ * Rewritten and ported to the merged powerpc tree:
+ * Copyright 2007 IBM Corporation
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * 2002 (c) MontaVista, Software, Inc.  This file is licensed under
+ * the terms of the GNU General Public License version 2.  This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#include <linux/init.h>
+#include <linux/of_platform.h>
+
+#include <asm/machdep.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/time.h>
+#include <asm/uic.h>
+#include <asm/ppc4xx.h>
+
+static __initdata struct of_device_id hcu4_of_bus[] = {
+	{ .compatible = "ibm,plb3", },
+	{ .compatible = "ibm,opb", },
+	{ .compatible = "ibm,ebc", },
+	{},
+};
+
+static int __init hcu4_device_probe(void)
+{
+	of_platform_bus_probe(NULL, hcu4_of_bus, NULL);
+	return 0;
+}
+machine_device_initcall(hcu4, hcu4_device_probe);
+
+static int __init hcu4_probe(void)
+{
+	unsigned long root = of_get_flat_dt_root();
+
+	if (!of_flat_dt_is_compatible(root, "netstal,hcu4"))
+		return 0;
+
+	return 1;
+}
+
+define_machine(hcu4) {
+	.name			= "HCU4",
+	.probe			= hcu4_probe,
+	.progress		= udbg_progress,
+	.init_IRQ		= uic_init_tree,
+	.get_irq		= uic_get_irq,
+	.restart		= ppc4xx_reset_system,
+	.calibrate_decr		= generic_calibrate_decr,
+};

arch/powerpc/platforms/40x/ppc40x_simple.c

+/*
+ * Generic PowerPC 40x platform support
+ *
+ * Copyright 2008 IBM Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; version 2 of the License.
+ *
+ * This implements simple platform support for PowerPC 44x chips.  This is
+ * mostly used for eval boards or other simple and "generic" 44x boards.  If
+ * your board has custom functions or hardware, then you will likely want to
+ * implement your own board.c file to accommodate it.
+ */
+
+#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
+#include <asm/ppc4xx.h>
+#include <asm/prom.h>
+#include <asm/time.h>
+#include <asm/udbg.h>
+#include <asm/uic.h>
+
+#include <linux/init.h>
+#include <linux/of_platform.h>
+
+static __initdata struct of_device_id ppc40x_of_bus[] = {
+	{ .compatible = "ibm,plb3", },
+	{ .compatible = "ibm,plb4", },
+	{ .compatible = "ibm,opb", },
+	{ .compatible = "ibm,ebc", },
+	{ .compatible = "simple-bus", },
+	{},
+};
+
+static int __init ppc40x_device_probe(void)
+{
+	of_platform_bus_probe(NULL, ppc40x_of_bus, NULL);
+
+	return 0;
+}
+machine_device_initcall(ppc40x_simple, ppc40x_device_probe);
+
+/* This is the list of boards that can be supported by this simple
+ * platform code.  This does _not_ mean the boards are compatible,
+ * as they most certainly are not from a device tree perspective.
+ * However, their differences are handled by the device tree and the
+ * drivers and therefore they don't need custom board support files.
+ *
+ * Again, if your board needs to do things differently then create a
+ * board.c file for it rather than adding it to this list.
+ */
+static char *board[] __initdata = {
+	"amcc,acadia"
+};
+
+static int __init ppc40x_probe(void)
+{
+	unsigned long root = of_get_flat_dt_root();
+	int i = 0;
+
+	for (i = 0; i < ARRAY_SIZE(board); i++) {
+		if (of_flat_dt_is_compatible(root, board[i])) {
+			ppc_pci_flags = PPC_PCI_REASSIGN_ALL_RSRC;
+			return 1;
+		}
+	}
+
+	return 0;
+}
+
+define_machine(ppc40x_simple) {
+	.name = "PowerPC 40x Platform",
+	.probe = ppc40x_probe,
+	.progress = udbg_progress,
+	.init_IRQ = uic_init_tree,
+	.get_irq = uic_get_irq,
+	.restart = ppc4xx_reset_system,
+	.calibrate_decr = generic_calibrate_decr,
+};

arch/powerpc/platforms/44x/Kconfig

@@ -167,6 +167,14 @@ config PPC44x_SIMPLE
 	help
 	  This option enables the simple PowerPC 44x platform support.
 
+config PPC4xx_GPIO
+	bool "PPC4xx GPIO support"
+	depends on 44x
+	select ARCH_REQUIRE_GPIOLIB
+	select GENERIC_GPIO
+	help
+	  Enable gpiolib support for ppc440 based boards
+
 # 44x specific CPU modules, selected based on the board above.
 config 440EP
 	bool

arch/powerpc/platforms/52xx/mpc52xx_common.c

@@ -99,10 +99,13 @@ mpc5200_setup_xlb_arbiter(void)
 	out_be32(&xlb->master_pri_enable, 0xff);
 	out_be32(&xlb->master_priority, 0x11111111);
 
-	/* Disable XLB pipelining
+	/*
+	 * Disable XLB pipelining
 	 * (cfr errate 292. We could do this only just before ATA PIO
 	 *  transaction and re-enable it afterwards ...)
+	 * Not needed on MPC5200B.
 	 */
+	if ((mfspr(SPRN_SVR) & MPC5200_SVR_MASK) == MPC5200_SVR)
 		out_be32(&xlb->config, in_be32(&xlb->config) | MPC52xx_XLB_CFG_PLDIS);
 
 	iounmap(xlb);

arch/powerpc/platforms/85xx/ksi8560.c

@@ -193,7 +193,6 @@ static void __init ksi8560_setup_arch(void)
 static void ksi8560_show_cpuinfo(struct seq_file *m)
 {
 	uint pvid, svid, phid1;
-	uint memsize = total_memory;
 
 	pvid = mfspr(SPRN_PVR);
 	svid = mfspr(SPRN_SVR);
@@ -215,9 +214,6 @@ static void ksi8560_show_cpuinfo(struct seq_file *m)
 	/* Display cpu Pll setting */
 	phid1 = mfspr(SPRN_HID1);
 	seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
-
-	/* Display the amount of memory */
-	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
 }
 
 static struct of_device_id __initdata of_bus_ids[] = {

arch/powerpc/platforms/85xx/mpc85xx_ads.c

@@ -207,7 +207,6 @@ static void __init mpc85xx_ads_setup_arch(void)
 static void mpc85xx_ads_show_cpuinfo(struct seq_file *m)
 {
 	uint pvid, svid, phid1;
-	uint memsize = total_memory;
 
 	pvid = mfspr(SPRN_PVR);
 	svid = mfspr(SPRN_SVR);
@@ -219,9 +218,6 @@ static void mpc85xx_ads_show_cpuinfo(struct seq_file *m)
 	/* Display cpu Pll setting */
 	phid1 = mfspr(SPRN_HID1);
 	seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
-
-	/* Display the amount of memory */
-	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
 }
 
 static struct of_device_id __initdata of_bus_ids[] = {

arch/powerpc/platforms/85xx/mpc85xx_cds.c

@@ -307,7 +307,6 @@ static void __init mpc85xx_cds_setup_arch(void)
 static void mpc85xx_cds_show_cpuinfo(struct seq_file *m)
 {
 	uint pvid, svid, phid1;
-	uint memsize = total_memory;
 
 	pvid = mfspr(SPRN_PVR);
 	svid = mfspr(SPRN_SVR);
@@ -320,9 +319,6 @@ static void mpc85xx_cds_show_cpuinfo(struct seq_file *m)
 	/* Display cpu Pll setting */
 	phid1 = mfspr(SPRN_HID1);
 	seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
-
-	/* Display the amount of memory */
-	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
 }
 
 

arch/powerpc/platforms/85xx/sbc8548.c

@@ -136,7 +136,6 @@ static void __init sbc8548_setup_arch(void)
 static void sbc8548_show_cpuinfo(struct seq_file *m)
 {
 	uint pvid, svid, phid1;
-	uint memsize = total_memory;
 
 	pvid = mfspr(SPRN_PVR);
 	svid = mfspr(SPRN_SVR);
@@ -149,9 +148,6 @@ static void sbc8548_show_cpuinfo(struct seq_file *m)
 	/* Display cpu Pll setting */
 	phid1 = mfspr(SPRN_HID1);
 	seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
-
-	/* Display the amount of memory */
-	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
 }
 
 static struct of_device_id __initdata of_bus_ids[] = {

arch/powerpc/platforms/85xx/sbc8560.c

@@ -194,7 +194,6 @@ static void __init sbc8560_setup_arch(void)
 static void sbc8560_show_cpuinfo(struct seq_file *m)
 {
 	uint pvid, svid, phid1;
-	uint memsize = total_memory;
 
 	pvid = mfspr(SPRN_PVR);
 	svid = mfspr(SPRN_SVR);
@@ -206,9 +205,6 @@ static void sbc8560_show_cpuinfo(struct seq_file *m)
 	/* Display cpu Pll setting */
 	phid1 = mfspr(SPRN_HID1);
 	seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
-
-	/* Display the amount of memory */
-	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
 }
 
 static struct of_device_id __initdata of_bus_ids[] = {

arch/powerpc/platforms/85xx/stx_gp3.c

@@ -130,7 +130,6 @@ static void __init stx_gp3_setup_arch(void)
 static void stx_gp3_show_cpuinfo(struct seq_file *m)
 {
 	uint pvid, svid, phid1;
-	uint memsize = total_memory;
 
 	pvid = mfspr(SPRN_PVR);
 	svid = mfspr(SPRN_SVR);
@@ -142,9 +141,6 @@ static void stx_gp3_show_cpuinfo(struct seq_file *m)
 	/* Display cpu Pll setting */
 	phid1 = mfspr(SPRN_HID1);
 	seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
-
-	/* Display the amount of memory */
-	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
 }
 
 static struct of_device_id __initdata of_bus_ids[] = {

arch/powerpc/platforms/85xx/tqm85xx.c

@@ -138,7 +138,6 @@ static void __init tqm85xx_setup_arch(void)
 static void tqm85xx_show_cpuinfo(struct seq_file *m)
 {
 	uint pvid, svid, phid1;
-	uint memsize = total_memory;
 
 	pvid = mfspr(SPRN_PVR);
 	svid = mfspr(SPRN_SVR);
@@ -150,9 +149,6 @@ static void tqm85xx_show_cpuinfo(struct seq_file *m)
 	/* Display cpu Pll setting */
 	phid1 = mfspr(SPRN_HID1);
 	seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
-
-	/* Display the amount of memory */
-	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
 }
 
 static struct of_device_id __initdata of_bus_ids[] = {

arch/powerpc/platforms/86xx/gef_sbc610.c

@@ -127,7 +127,6 @@ static unsigned int gef_sbc610_get_fpga_rev(void)
 
 static void gef_sbc610_show_cpuinfo(struct seq_file *m)
 {
-	uint memsize = total_memory;
 	uint svid = mfspr(SPRN_SVR);
 
 	seq_printf(m, "Vendor\t\t: GE Fanuc Intelligent Platforms\n");
@@ -137,7 +136,6 @@ static void gef_sbc610_show_cpuinfo(struct seq_file *m)
 	seq_printf(m, "FPGA Revision\t: %u\n", gef_sbc610_get_fpga_rev());
 
 	seq_printf(m, "SVR\t\t: 0x%x\n", svid);
-	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
 }
 
 static void __init gef_sbc610_nec_fixup(struct pci_dev *pdev)

arch/powerpc/platforms/86xx/mpc86xx_hpcn.c

@@ -101,13 +101,11 @@ mpc86xx_hpcn_setup_arch(void)
 static void
 mpc86xx_hpcn_show_cpuinfo(struct seq_file *m)
 {
-	uint memsize = total_memory;
 	uint svid = mfspr(SPRN_SVR);
 
 	seq_printf(m, "Vendor\t\t: Freescale Semiconductor\n");
 
 	seq_printf(m, "SVR\t\t: 0x%x\n", svid);
-	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
 }
 
 

arch/powerpc/platforms/86xx/sbc8641d.c

@@ -63,13 +63,11 @@ sbc8641_setup_arch(void)
 static void
 sbc8641_show_cpuinfo(struct seq_file *m)
 {
-	uint memsize = total_memory;
 	uint svid = mfspr(SPRN_SVR);
 
 	seq_printf(m, "Vendor\t\t: Wind River Systems\n");
 
 	seq_printf(m, "SVR\t\t: 0x%x\n", svid);
-	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
 }
 
 

arch/powerpc/platforms/cell/ras.c

@@ -21,6 +21,7 @@
 #include <asm/machdep.h>
 #include <asm/rtas.h>
 #include <asm/cell-regs.h>
+#include <asm/kdump.h>
 
 #include "ras.h"
 
@@ -111,9 +112,8 @@ static int __init cbe_ptcal_enable_on_node(int nid, int order)
 	int ret = -ENOMEM;
 	unsigned long addr;
 
-#ifdef CONFIG_CRASH_DUMP
+	if (__kdump_flag)
 		rtas_call(ptcal_stop_tok, 1, 1, NULL, nid);
-#endif
 
 	area = kmalloc(sizeof(*area), GFP_KERNEL);
 	if (!area)

arch/powerpc/platforms/cell/smp.c

@@ -54,8 +54,8 @@
 #endif
 
 /*
- * The primary thread of each non-boot processor is recorded here before
- * smp init.
+ * The Primary thread of each non-boot processor was started from the OF client
+ * interface by prom_hold_cpus and is spinning on secondary_hold_spinloop.
  */
 static cpumask_t of_spin_map;
 
@@ -208,11 +208,7 @@ void __init smp_init_cell(void)
 	/* Mark threads which are still spinning in hold loops. */
 	if (cpu_has_feature(CPU_FTR_SMT)) {
 		for_each_present_cpu(i) {
-			if (i % 2 == 0)
-				/*
-				 * Even-numbered logical cpus correspond to
-				 * primary threads.
-				 */
+			if (cpu_thread_in_core(i) == 0)
 				cpu_set(i, of_spin_map);
 		}
 	} else {

arch/powerpc/platforms/cell/spufs/file.c

@@ -548,6 +548,11 @@ spufs_regs_read(struct file *file, char __user *buffer,
 	int ret;
 	struct spu_context *ctx = file->private_data;
 
+	/* pre-check for file position: if we'd return EOF, there's no point
+	 * causing a deschedule */
+	if (*pos >= sizeof(ctx->csa.lscsa->gprs))
+		return 0;
+
 	ret = spu_acquire_saved(ctx);
 	if (ret)
 		return ret;
@@ -2426,38 +2431,49 @@ static inline int spufs_switch_log_avail(struct spu_context *ctx)
 static int spufs_switch_log_open(struct inode *inode, struct file *file)
 {
 	struct spu_context *ctx = SPUFS_I(inode)->i_ctx;
+	int rc;
+
+	rc = spu_acquire(ctx);
+	if (rc)
+		return rc;
 
-	/*
-	 * We (ab-)use the mapping_lock here because it serves the similar
-	 * purpose for synchronizing open/close elsewhere.  Maybe it should
-	 * be renamed eventually.
-	 */
-	mutex_lock(&ctx->mapping_lock);
 	if (ctx->switch_log) {
-		spin_lock(&ctx->switch_log->lock);
-		ctx->switch_log->head = 0;
-		ctx->switch_log->tail = 0;
-		spin_unlock(&ctx->switch_log->lock);
-	} else {
-		/*
-		 * We allocate the switch log data structures on first open.
-		 * They will never be free because we assume a context will
-		 * be traced until it goes away.
-		 */
-		ctx->switch_log = kzalloc(sizeof(struct switch_log) +
+		rc = -EBUSY;
+		goto out;
+	}
+
+	ctx->switch_log = kmalloc(sizeof(struct switch_log) +
 		SWITCH_LOG_BUFSIZE * sizeof(struct switch_log_entry),
 		GFP_KERNEL);
-		if (!ctx->switch_log)
+
+	if (!ctx->switch_log) {
+		rc = -ENOMEM;
 		goto out;
-		spin_lock_init(&ctx->switch_log->lock);
-		init_waitqueue_head(&ctx->switch_log->wait);
 	}
-	mutex_unlock(&ctx->mapping_lock);
+
+	ctx->switch_log->head = ctx->switch_log->tail = 0;
+	init_waitqueue_head(&ctx->switch_log->wait);
+	rc = 0;
+
+out:
+	spu_release(ctx);
+	return rc;
+}
+
+static int spufs_switch_log_release(struct inode *inode, struct file *file)
+{
+	struct spu_context *ctx = SPUFS_I(inode)->i_ctx;
+	int rc;
+
+	rc = spu_acquire(ctx);
+	if (rc)
+		return rc;
+
+	kfree(ctx->switch_log);
+	ctx->switch_log = NULL;
+	spu_release(ctx);
 
 	return 0;
- out:
-	mutex_unlock(&ctx->mapping_lock);
-	return -ENOMEM;
 }
 
 static int switch_log_sprint(struct spu_context *ctx, char *tbuf, int n)
@@ -2485,42 +2501,54 @@ static ssize_t spufs_switch_log_read(struct file *file, char __user *buf,
 	if (!buf || len < 0)
 		return -EINVAL;
 
+	error = spu_acquire(ctx);
+	if (error)
+		return error;
+
 	while (cnt < len) {
 		char tbuf[128];
 		int width;
 
-		if (file->f_flags & O_NONBLOCK) {
-			if (spufs_switch_log_used(ctx) <= 0)
-				return cnt ? cnt : -EAGAIN;
+		if (spufs_switch_log_used(ctx) == 0) {
+			if (cnt > 0) {
+				/* If there's data ready to go, we can
+				 * just return straight away */
+				break;
+
+			} else if (file->f_flags & O_NONBLOCK) {
+				error = -EAGAIN;
+				break;
+
 			} else {
-			/* Wait for data in buffer */
-			error = wait_event_interruptible(ctx->switch_log->wait,
+				/* spufs_wait will drop the mutex and
+				 * re-acquire, but since we're in read(), the
+				 * file cannot be _released (and so
+				 * ctx->switch_log is stable).
+				 */
+				error = spufs_wait(ctx->switch_log->wait,
 						spufs_switch_log_used(ctx) > 0);
+
+				/* On error, spufs_wait returns without the
+				 * state mutex held */
 				if (error)
-				break;
-		}
+					return error;
 
-		spin_lock(&ctx->switch_log->lock);
-		if (ctx->switch_log->head == ctx->switch_log->tail) {
-			/* multiple readers race? */
-			spin_unlock(&ctx->switch_log->lock);
+				/* We may have had entries read from underneath
+				 * us while we dropped the mutex in spufs_wait,
+				 * so re-check */
+				if (spufs_switch_log_used(ctx) == 0)
 					continue;
 			}
+		}
 
 		width = switch_log_sprint(ctx, tbuf, sizeof(tbuf));
-		if (width < len) {
+		if (width < len)
 			ctx->switch_log->tail =
 				(ctx->switch_log->tail + 1) %
 				 SWITCH_LOG_BUFSIZE;
-		}
-
-		spin_unlock(&ctx->switch_log->lock);
-
-		/*
-		 * If the record is greater than space available return
-		 * partial buffer (so far)
-		 */
-		if (width >= len)
+		else
+			/* If the record is greater than space available return
+			 * partial buffer (so far) */
 			break;
 
 		error = copy_to_user(buf + cnt, tbuf, width);
@@ -2529,6 +2557,8 @@ static ssize_t spufs_switch_log_read(struct file *file, char __user *buf,
 		cnt += width;
 	}
 
+	spu_release(ctx);
+
 	return cnt == 0 ? error : cnt;
 }
 
@@ -2537,12 +2567,19 @@ static unsigned int spufs_switch_log_poll(struct file *file, poll_table *wait)
 	struct inode *inode = file->f_path.dentry->d_inode;
 	struct spu_context *ctx = SPUFS_I(inode)->i_ctx;
 	unsigned int mask = 0;
+	int rc;
 
 	poll_wait(file, &ctx->switch_log->wait, wait);
 
+	rc = spu_acquire(ctx);
+	if (rc)
+		return rc;
+
 	if (spufs_switch_log_used(ctx) > 0)
 		mask |= POLLIN;
 
+	spu_release(ctx);
+
 	return mask;
 }
 
@@ -2551,15 +2588,20 @@ static const struct file_operations spufs_switch_log_fops = {
 	.open		= spufs_switch_log_open,
 	.read		= spufs_switch_log_read,
 	.poll		= spufs_switch_log_poll,
+	.release	= spufs_switch_log_release,
 };
 
+/**
+ * Log a context switch event to a switch log reader.
+ *
+ * Must be called with ctx->state_mutex held.
+ */
 void spu_switch_log_notify(struct spu *spu, struct spu_context *ctx,
 		u32 type, u32 val)
 {
 	if (!ctx->switch_log)
 		return;
 
-	spin_lock(&ctx->switch_log->lock);
 	if (spufs_switch_log_avail(ctx) > 1) {
 		struct switch_log_entry *p;
 
@@ -2573,7 +2615,6 @@ void spu_switch_log_notify(struct spu *spu, struct spu_context *ctx,
 		ctx->switch_log->head =
 			(ctx->switch_log->head + 1) % SWITCH_LOG_BUFSIZE;
 	}
-	spin_unlock(&ctx->switch_log->lock);
 
 	wake_up(&ctx->switch_log->wait);
 }

arch/powerpc/platforms/cell/spufs/run.c

@@ -249,6 +249,7 @@ static int spu_run_fini(struct spu_context *ctx, u32 *npc,
 
 	spuctx_switch_state(ctx, SPU_UTIL_IDLE_LOADED);
 	clear_bit(SPU_SCHED_SPU_RUN, &ctx->sched_flags);
+	spu_switch_log_notify(NULL, ctx, SWITCH_LOG_EXIT, *status);
 	spu_release(ctx);
 
 	if (signal_pending(current))
@@ -417,8 +418,6 @@ long spufs_run_spu(struct spu_context *ctx, u32 *npc, u32 *event)
 	ret = spu_run_fini(ctx, npc, &status);
 	spu_yield(ctx);
 
-	spu_switch_log_notify(NULL, ctx, SWITCH_LOG_EXIT, status);
-
 	if ((status & SPU_STATUS_STOPPED_BY_STOP) &&
 	    (((status >> SPU_STOP_STATUS_SHIFT) & 0x3f00) == 0x2100))
 		ctx->stats.libassist++;

arch/powerpc/platforms/cell/spufs/sched.c

@@ -312,6 +312,15 @@ static struct spu *aff_ref_location(struct spu_context *ctx, int mem_aff,
 	 */
 	node = cpu_to_node(raw_smp_processor_id());
 	for (n = 0; n < MAX_NUMNODES; n++, node++) {
+		/*
+		 * "available_spus" counts how many spus are not potentially
+		 * going to be used by other affinity gangs whose reference
+		 * context is already in place. Although this code seeks to
+		 * avoid having affinity gangs with a summed amount of
+		 * contexts bigger than the amount of spus in the node,
+		 * this may happen sporadically. In this case, available_spus
+		 * becomes negative, which is harmless.
+		 */
 		int available_spus;
 
 		node = (node < MAX_NUMNODES) ? node : 0;
@@ -321,11 +330,9 @@ static struct spu *aff_ref_location(struct spu_context *ctx, int mem_aff,
 		available_spus = 0;
 		mutex_lock(&cbe_spu_info[node].list_mutex);
 		list_for_each_entry(spu, &cbe_spu_info[node].spus, cbe_list) {
-			if (spu->ctx && spu->ctx->gang
-					&& spu->ctx->aff_offset == 0)
-				available_spus -=
-					(spu->ctx->gang->contexts - 1);
-			else
+			if (spu->ctx && spu->ctx->gang && !spu->ctx->aff_offset
+					&& spu->ctx->gang->aff_ref_spu)
+				available_spus -= spu->ctx->gang->contexts;
 			available_spus++;
 		}
 		if (available_spus < ctx->gang->contexts) {
@@ -437,6 +444,11 @@ static void spu_unbind_context(struct spu *spu, struct spu_context *ctx)
 		atomic_dec(&cbe_spu_info[spu->node].reserved_spus);
 
 	if (ctx->gang)
+		/*
+		 * If ctx->gang->aff_sched_count is positive, SPU affinity is
+		 * being considered in this gang. Using atomic_dec_if_positive
+		 * allow us to skip an explicit check for affinity in this gang
+		 */
 		atomic_dec_if_positive(&ctx->gang->aff_sched_count);
 
 	spu_switch_notify(spu, NULL);

arch/powerpc/platforms/cell/spufs/spufs.h

@@ -65,7 +65,6 @@ enum {
 };
 
 struct switch_log {
-	spinlock_t		lock;
 	wait_queue_head_t	wait;
 	unsigned long		head;
 	unsigned long		tail;

arch/powerpc/platforms/cell/spufs/sputrace.c

@@ -40,6 +40,7 @@ static DECLARE_WAIT_QUEUE_HEAD(sputrace_wait);
 static ktime_t sputrace_start;
 static unsigned long sputrace_head, sputrace_tail;
 static struct sputrace *sputrace_log;
+static int sputrace_logging;
 
 static int sputrace_used(void)
 {
@@ -79,6 +80,11 @@ static ssize_t sputrace_read(struct file *file, char __user *buf,
 		char tbuf[128];
 		int width;
 
+		/* If we have data ready to return, don't block waiting
+		 * for more */
+		if (cnt > 0 && sputrace_used() == 0)
+			break;
+
 		error = wait_event_interruptible(sputrace_wait,
 						 sputrace_used() > 0);
 		if (error)
@@ -109,11 +115,29 @@ static ssize_t sputrace_read(struct file *file, char __user *buf,
 
 static int sputrace_open(struct inode *inode, struct file *file)
 {
+	int rc;
+
 	spin_lock(&sputrace_lock);
+	if (sputrace_logging) {
+		rc = -EBUSY;
+		goto out;
+	}
+
+	sputrace_logging = 1;
 	sputrace_head = sputrace_tail = 0;
 	sputrace_start = ktime_get();
+	rc = 0;
+
+out:
 	spin_unlock(&sputrace_lock);
+	return rc;
+}
 
+static int sputrace_release(struct inode *inode, struct file *file)
+{
+	spin_lock(&sputrace_lock);
+	sputrace_logging = 0;
+	spin_unlock(&sputrace_lock);
 	return 0;
 }
 
@@ -121,12 +145,19 @@ static const struct file_operations sputrace_fops = {
 	.owner   = THIS_MODULE,
 	.open    = sputrace_open,
 	.read    = sputrace_read,
+	.release = sputrace_release,
 };
 
 static void sputrace_log_item(const char *name, struct spu_context *ctx,
 		struct spu *spu)
 {
 	spin_lock(&sputrace_lock);
+
+	if (!sputrace_logging) {
+		spin_unlock(&sputrace_lock);
+		return;
+	}
+
 	if (sputrace_avail() > 1) {
 		struct sputrace *t = sputrace_log + sputrace_head;
 

arch/powerpc/platforms/embedded6xx/c2k.c

@@ -116,10 +116,7 @@ static void c2k_restart(char *cmd)
 
 void c2k_show_cpuinfo(struct seq_file *m)
 {
-	uint memsize = total_memory;
-
 	seq_printf(m, "Vendor\t\t: GEFanuc\n");
-	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
 	seq_printf(m, "coherency\t: %s\n", COHERENCY_SETTING);
 }
 

arch/powerpc/platforms/embedded6xx/prpmc2800.c

@@ -119,10 +119,7 @@ static void prpmc2800_restart(char *cmd)
 
 void prpmc2800_show_cpuinfo(struct seq_file *m)
 {
-	uint memsize = total_memory;
-
 	seq_printf(m, "Vendor\t\t: Motorola\n");
-	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
 	seq_printf(m, "coherency\t: %s\n", PPRPM2800_COHERENCY_SETTING);
 }
 

arch/powerpc/platforms/pseries/hotplug-memory.c

@@ -22,6 +22,12 @@ static int pseries_remove_lmb(unsigned long base, unsigned int lmb_size)
 	int ret;
 
 	start_pfn = base >> PAGE_SHIFT;
+
+	if (!pfn_valid(start_pfn)) {
+		lmb_remove(base, lmb_size);
+		return 0;
+	}
+
 	zone = page_zone(pfn_to_page(start_pfn));
 
 	/*

arch/powerpc/platforms/pseries/iommu.c

@@ -44,6 +44,7 @@
 #include <asm/tce.h>
 #include <asm/ppc-pci.h>
 #include <asm/udbg.h>
+#include <asm/kdump.h>
 
 #include "plpar_wrappers.h"
 
@@ -291,9 +292,8 @@ static void iommu_table_setparms(struct pci_controller *phb,
 
 	tbl->it_base = (unsigned long)__va(*basep);
 
-#ifndef CONFIG_CRASH_DUMP
+	if (!__kdump_flag)
 		memset((void *)tbl->it_base, 0, *sizep);
-#endif
 
 	tbl->it_busno = phb->bus->number;
 

arch/powerpc/platforms/pseries/smp.c

@@ -52,8 +52,8 @@
 
 
 /*
- * The primary thread of each non-boot processor is recorded here before
- * smp init.
+ * The Primary thread of each non-boot processor was started from the OF client
+ * interface by prom_hold_cpus and is spinning on secondary_hold_spinloop.
  */
 static cpumask_t of_spin_map;
 
@@ -161,8 +161,7 @@ static void __devinit smp_pSeries_kick_cpu(int nr)
 static int smp_pSeries_cpu_bootable(unsigned int nr)
 {
 	/* Special case - we inhibit secondary thread startup
-	 * during boot if the user requests it.  Odd-numbered
-	 * cpus are assumed to be secondary threads.
+	 * during boot if the user requests it.
 	 */
 	if (system_state < SYSTEM_RUNNING &&
 	    cpu_has_feature(CPU_FTR_SMT) &&
@@ -199,11 +198,7 @@ static void __init smp_init_pseries(void)
 	/* Mark threads which are still spinning in hold loops. */
 	if (cpu_has_feature(CPU_FTR_SMT)) {
 		for_each_present_cpu(i) { 
-			if (i % 2 == 0)
-				/*
-				 * Even-numbered logical cpus correspond to
-				 * primary threads.
-				 */
+			if (cpu_thread_in_core(i) == 0)
 				cpu_set(i, of_spin_map);
 		}
 	} else {

arch/powerpc/sysdev/Makefile

@@ -37,6 +37,7 @@ obj-$(CONFIG_OF_RTC)		+= of_rtc.o
 ifeq ($(CONFIG_PCI),y)
 obj-$(CONFIG_4xx)		+= ppc4xx_pci.o
 endif
+obj-$(CONFIG_PPC4xx_GPIO)	+= ppc4xx_gpio.o
 
 obj-$(CONFIG_CPM)		+= cpm_common.o
 obj-$(CONFIG_CPM2)		+= cpm2.o cpm2_pic.o

arch/powerpc/sysdev/ppc4xx_gpio.c

+/*
+ * PPC4xx gpio driver
+ *
+ * Copyright (c) 2008 Harris Corporation
+ * Copyright (c) 2008 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ *
+ * Author: Steve Falco <sfalco@harris.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/spinlock.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/gpio.h>
+#include <linux/types.h>
+
+#define GPIO_MASK(gpio)		(0x80000000 >> (gpio))
+#define GPIO_MASK2(gpio)	(0xc0000000 >> ((gpio) * 2))
+
+/* Physical GPIO register layout */
+struct ppc4xx_gpio {
+	__be32 or;
+	__be32 tcr;
+	__be32 osrl;
+	__be32 osrh;
+	__be32 tsrl;
+	__be32 tsrh;
+	__be32 odr;
+	__be32 ir;
+	__be32 rr1;
+	__be32 rr2;
+	__be32 rr3;
+	__be32 reserved1;
+	__be32 isr1l;
+	__be32 isr1h;
+	__be32 isr2l;
+	__be32 isr2h;
+	__be32 isr3l;
+	__be32 isr3h;
+};
+
+struct ppc4xx_gpio_chip {
+	struct of_mm_gpio_chip mm_gc;
+	spinlock_t lock;
+};
+
+/*
+ * GPIO LIB API implementation for GPIOs
+ *
+ * There are a maximum of 32 gpios in each gpio controller.
+ */
+
+static inline struct ppc4xx_gpio_chip *
+to_ppc4xx_gpiochip(struct of_mm_gpio_chip *mm_gc)
+{
+	return container_of(mm_gc, struct ppc4xx_gpio_chip, mm_gc);
+}
+
+static int ppc4xx_gpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct ppc4xx_gpio __iomem *regs = mm_gc->regs;
+
+	return in_be32(&regs->ir) & GPIO_MASK(gpio);
+}
+
+static inline void
+__ppc4xx_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct ppc4xx_gpio __iomem *regs = mm_gc->regs;
+
+	if (val)
+		setbits32(&regs->or, GPIO_MASK(gpio));
+	else
+		clrbits32(&regs->or, GPIO_MASK(gpio));
+}
+
+static void
+ppc4xx_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct ppc4xx_gpio_chip *chip = to_ppc4xx_gpiochip(mm_gc);
+	unsigned long flags;
+
+	spin_lock_irqsave(&chip->lock, flags);
+
+	__ppc4xx_gpio_set(gc, gpio, val);
+
+	spin_unlock_irqrestore(&chip->lock, flags);
+
+	pr_debug("%s: gpio: %d val: %d\n", __func__, gpio, val);
+}
+
+static int ppc4xx_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct ppc4xx_gpio_chip *chip = to_ppc4xx_gpiochip(mm_gc);
+	struct ppc4xx_gpio __iomem *regs = mm_gc->regs;
+	unsigned long flags;
+
+	spin_lock_irqsave(&chip->lock, flags);
+
+	/* Disable open-drain function */
+	clrbits32(&regs->odr, GPIO_MASK(gpio));
+
+	/* Float the pin */
+	clrbits32(&regs->tcr, GPIO_MASK(gpio));
+
+	/* Bits 0-15 use TSRL/OSRL, bits 16-31 use TSRH/OSRH */
+	if (gpio < 16) {
+		clrbits32(&regs->osrl, GPIO_MASK2(gpio));
+		clrbits32(&regs->tsrl, GPIO_MASK2(gpio));
+	} else {
+		clrbits32(&regs->osrh, GPIO_MASK2(gpio));
+		clrbits32(&regs->tsrh, GPIO_MASK2(gpio));
+	}
+
+	spin_unlock_irqrestore(&chip->lock, flags);
+
+	return 0;
+}
+
+static int
+ppc4xx_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct ppc4xx_gpio_chip *chip = to_ppc4xx_gpiochip(mm_gc);
+	struct ppc4xx_gpio __iomem *regs = mm_gc->regs;
+	unsigned long flags;
+
+	spin_lock_irqsave(&chip->lock, flags);
+
+	/* First set initial value */
+	__ppc4xx_gpio_set(gc, gpio, val);
+
+	/* Disable open-drain function */
+	clrbits32(&regs->odr, GPIO_MASK(gpio));
+
+	/* Drive the pin */
+	setbits32(&regs->tcr, GPIO_MASK(gpio));
+
+	/* Bits 0-15 use TSRL, bits 16-31 use TSRH */
+	if (gpio < 16) {
+		clrbits32(&regs->osrl, GPIO_MASK2(gpio));
+		clrbits32(&regs->tsrl, GPIO_MASK2(gpio));
+	} else {
+		clrbits32(&regs->osrh, GPIO_MASK2(gpio));
+		clrbits32(&regs->tsrh, GPIO_MASK2(gpio));
+	}
+
+	spin_unlock_irqrestore(&chip->lock, flags);
+
+	pr_debug("%s: gpio: %d val: %d\n", __func__, gpio, val);
+
+	return 0;
+}
+
+static int __init ppc4xx_add_gpiochips(void)
+{
+	struct device_node *np;
+
+	for_each_compatible_node(np, NULL, "ibm,ppc4xx-gpio") {
+		int ret;
+		struct ppc4xx_gpio_chip *ppc4xx_gc;
+		struct of_mm_gpio_chip *mm_gc;
+		struct of_gpio_chip *of_gc;
+		struct gpio_chip *gc;
+
+		ppc4xx_gc = kzalloc(sizeof(*ppc4xx_gc), GFP_KERNEL);
+		if (!ppc4xx_gc) {
+			ret = -ENOMEM;
+			goto err;
+		}
+
+		spin_lock_init(&ppc4xx_gc->lock);
+
+		mm_gc = &ppc4xx_gc->mm_gc;
+		of_gc = &mm_gc->of_gc;
+		gc = &of_gc->gc;
+
+		of_gc->gpio_cells = 2;
+		gc->ngpio = 32;
+		gc->direction_input = ppc4xx_gpio_dir_in;
+		gc->direction_output = ppc4xx_gpio_dir_out;
+		gc->get = ppc4xx_gpio_get;
+		gc->set = ppc4xx_gpio_set;
+
+		ret = of_mm_gpiochip_add(np, mm_gc);
+		if (ret)
+			goto err;
+		continue;
+err:
+		pr_err("%s: registration failed with status %d\n",
+		       np->full_name, ret);
+		kfree(ppc4xx_gc);
+		/* try others anyway */
+	}
+	return 0;
+}
+arch_initcall(ppc4xx_add_gpiochips);

drivers/char/hvc_console.h

@@ -27,6 +27,7 @@
 #ifndef HVC_CONSOLE_H
 #define HVC_CONSOLE_H
 #include <linux/kref.h>
+#include <linux/tty.h>
 
 /*
  * This is the max number of console adapters that can/will be found as
@@ -56,6 +57,8 @@ struct hvc_struct {
 	struct hv_ops *ops;
 	int irq_requested;
 	int data;
+	struct winsize ws;
+	struct work_struct tty_resize;
 	struct list_head next;
 	struct kref kref; /* ref count & hvc_struct lifetime */
 };
@@ -65,9 +68,10 @@ struct hv_ops {
 	int (*get_chars)(uint32_t vtermno, char *buf, int count);
 	int (*put_chars)(uint32_t vtermno, const char *buf, int count);
 
-	/* Callbacks for notification. Called in open and close */
+	/* Callbacks for notification. Called in open, close and hangup */
 	int (*notifier_add)(struct hvc_struct *hp, int irq);
 	void (*notifier_del)(struct hvc_struct *hp, int irq);
+	void (*notifier_hangup)(struct hvc_struct *hp, int irq);
 };
 
 /* Register a vterm and a slot index for use as a console (console_init) */
@@ -77,15 +81,19 @@ extern int hvc_instantiate(uint32_t vtermno, int index, struct hv_ops *ops);
 extern struct hvc_struct * __devinit hvc_alloc(uint32_t vtermno, int data,
 				struct hv_ops *ops, int outbuf_size);
 /* remove a vterm from hvc tty operation (module_exit or hotplug remove) */
-extern int __devexit hvc_remove(struct hvc_struct *hp);
+extern int hvc_remove(struct hvc_struct *hp);
 
 /* data available */
 int hvc_poll(struct hvc_struct *hp);
 void hvc_kick(void);
 
+/* Resize hvc tty terminal window */
+extern void hvc_resize(struct hvc_struct *hp, struct winsize ws);
+
 /* default notifier for irq based notification */
 extern int notifier_add_irq(struct hvc_struct *hp, int data);
 extern void notifier_del_irq(struct hvc_struct *hp, int data);
+extern void notifier_hangup_irq(struct hvc_struct *hp, int data);
 
 
 #if defined(CONFIG_XMON) && defined(CONFIG_SMP)

drivers/char/hvc_irq.c

@@ -42,3 +42,8 @@ void notifier_del_irq(struct hvc_struct *hp, int irq)
 	free_irq(irq, hp);
 	hp->irq_requested = 0;
 }
+
+void notifier_hangup_irq(struct hvc_struct *hp, int irq)
+{
+	notifier_del_irq(hp, irq);
+}

drivers/char/hvc_iseries.c

@@ -202,6 +202,7 @@ static struct hv_ops hvc_get_put_ops = {
 	.put_chars = put_chars,
 	.notifier_add = notifier_add_irq,
 	.notifier_del = notifier_del_irq,
+	.notifier_hangup = notifier_hangup_irq,
 };
 
 static int __devinit hvc_vio_probe(struct vio_dev *vdev,

drivers/char/hvc_vio.c

@@ -82,6 +82,7 @@ static struct hv_ops hvc_get_put_ops = {
 	.put_chars = hvc_put_chars,
 	.notifier_add = notifier_add_irq,
 	.notifier_del = notifier_del_irq,
+	.notifier_hangup = notifier_hangup_irq,
 };
 
 static int __devinit hvc_vio_probe(struct vio_dev *vdev,

drivers/char/hvc_xen.c

@@ -102,6 +102,7 @@ static struct hv_ops hvc_ops = {
 	.put_chars = write_console,
 	.notifier_add = notifier_add_irq,
 	.notifier_del = notifier_del_irq,
+	.notifier_hangup = notifier_hangup_irq,
 };
 
 static int __init xen_init(void)