ARM: DTS: Add minimal Support for Logic PD DM3730 SOM-LV

The Logic PD DM37xx SOM-LV devkit consists of a base board and a SOM.
While the SOM (System on Module) supports Bluetooth and WiFi, LPD did not
obtain an FCC ID, so anyone who uses it will have to go through certification.

I have only tested the Type 28 Display, SMSC9211 Ethernet, SD/MMC and basic
power management, however the overall current seems high.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts

+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "omap36xx.dtsi"
+#include "logicpd-som-lv.dtsi"
+#include "omap-gpmc-smsc9221.dtsi"
+
+/ {
+	model = "LogicPD Zoom DM3730 SOM-LV Development Kit";
+	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3";
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_key_pins>;
+
+		sysboot2 {
+			label = "gpio3";
+			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;	/* gpio_111 / uP_GPIO_3 */
+			linux,code = <BTN_0>;
+			wakeup-source;
+		};
+	};
+
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "omap3logic";
+		ti,mcbsp = <&mcbsp2>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins &led_pins_wkup>;
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;	/* gpio133 */
+			linux,default-trigger = "cpu0";
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;	/* gpio11 */
+			linux,default-trigger = "none";
+		};
+	};
+};
+
+&vaux1 {
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+};
+
+&vaux4 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+};
+
+&mcbsp2 {
+	status = "okay";
+};
+
+&charger {
+	ti,bb-uvolt = <3200000>;
+	ti,bb-uamp = <150>;
+};
+
+&gpmc {
+	ranges = <1 0 0x08000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
+
+	ethernet@gpmc {
+		pinctrl-names = "default";
+		pinctrl-0 = <&lan9221_pins>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;		/* gpio_152 */
+		reg = <1 0 0xff>;
+	};
+};
+
+&vpll2 {
+	regulator-always-on;
+};
+
+&dss {
+	status = "ok";
+	vdds_dsi-supply = <&vpll2>;
+	vdda_video-supply = <&video_reg>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_dpi_pins1>;
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&lcd_in>;
+			data-lines = <16>;
+		};
+	};
+};
+
+/ {
+	aliases {
+		display0 = &lcd0;
+	};
+
+	video_reg: video_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	lcd0: display@0 {
+		compatible = "panel-dpi";
+		label = "28";
+		status = "okay";
+		/* default-on; */
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_enable_pin>;
+		enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;	/* gpio155, lcd INI */
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_out>;
+			};
+		};
+
+		panel-timing {
+			clock-frequency = <9000000>;
+			hactive = <480>;
+			vactive = <272>;
+			hfront-porch = <3>;
+			hback-porch = <2>;
+			hsync-len = <42>;
+			vback-porch = <3>;
+			vfront-porch = <2>;
+			vsync-len = <11>;
+			hsync-active = <1>;
+			vsync-active = <1>;
+			de-active = <1>;
+			pixelclk-active = <0>;
+		};
+	};
+
+	bl: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight_pins>;
+		pwms = <&twl_pwm 0 5000000>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <7>;
+		enable-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* gpio_8 */
+	};
+};
+
+&mmc1 {
+	interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins &mmc1_cd>;
+	wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>;		/* gpio_126 */
+	cd-gpios = <&gpio4 14 IRQ_TYPE_LEVEL_LOW>;		/* gpio_110 */
+	vmmc-supply = <&vmmc1>;
+	bus-width = <4>;
+	cap-power-off-card;
+};
+
+&omap3_pmx_core {
+	gpio_key_pins: pinmux_gpio_key_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4)	/* cam_xclkb.gpio_111 / uP_GPIO_3*/
+		>;
+	};
+
+	led_pins: pinmux_led_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x215e, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* sdmmc2_dat1.gpio_133 / uP_GPIO_0 */
+		>;
+	};
+
+	lan9221_pins: pinmux_lan9221_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
+			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
+			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat0.sdmmc1_dat0 */
+			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat1.sdmmc1_dat1 */
+			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat2.sdmmc1_dat2 */
+			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat3.sdmmc1_dat3 */
+			OMAP3_CORE1_IOPAD(0x2132, PIN_INPUT_PULLUP | MUX_MODE4)	/* cam_strobe.gpio_126 sdmmc1_wp*/
+		>;
+	};
+
+	lcd_enable_pin: pinmux_lcd_enable_pin {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* mcbsp4_fs.gpio_155 */
+		>;
+	};
+
+	dss_dpi_pins1: pinmux_dss_dpi_pins1 {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_acbias.dss_acbias */
+
+			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data0.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data1.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data2.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data3.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data4.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data5.dss_data5 */
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data15.dss_data15 */
+		>;
+	};
+};
+
+&omap3_pmx_wkup {
+	led_pins_wkup: pinmux_led_pins_wkup {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu0.gpio_11 / uP_GPIO_1 */
+		>;
+	};
+
+	backlight_pins: pinmux_backlight_pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* sys_boot6.gpio_8 */
+		>;
+	};
+
+	mmc1_cd: pinmux_mmc1_cd {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4)	/* cam_d11.gpio_110 */
+		>;
+	};
+};
+
+
+&uart1 {
+	interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
+};
+
+/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */
+&usb_otg_hs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb_otg_pins>;
+	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
+	mode = <3>;
+	power = <50>;
+};

arch/arm/boot/dts/logicpd-som-lv.dtsi

+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vcc>;
+		};
+	};
+
+	wl12xx_vmmc: wl12xx_vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio1 3 0>;   /* gpio_3 */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		vin-supply = <&vmmc2>;
+	};
+};
+
+&gpmc {
+	ranges = <0 0 0x00000000 0x1000000>;	/* CS0: 16MB for NAND */
+
+	nand@0,0 {
+		linux,mtd-name = "micron,mt29f4g16abbda3w";
+		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		nand-bus-width = <16>;
+		ti,nand-ecc-opt = "bch8";
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		gpmc,device-width = <2>;
+
+		gpmc,page-burst-access-ns = <5>;
+		gpmc,cycle2cycle-delay-ns = <50>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */
+
+		x-loader@0 {
+			label = "x-loader";
+			reg = <0 0x80000>;
+		};
+
+		bootloaders@80000 {
+			label = "u-boot";
+			reg = <0x80000 0x1e0000>;
+		};
+
+		bootloaders_env@260000 {
+			label = "u-boot-env";
+			reg = <0x260000 0x20000>;
+		};
+
+		kernel@280000 {
+			label = "kernel";
+			reg = <0x280000 0x400000>;
+		};
+
+		filesystem@680000 {
+			label = "fs";
+			reg = <0x680000 0>;	/* 0 = MTDPART_SIZ_FULL */
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+			codec {
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+};
+
+&mmc3 {
+	interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
+	pinctrl-0 = <&mmc3_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&wl12xx_vmmc>;
+	non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1273";
+		reg = <2>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
+		ref-clock-frequency = <26000000>;
+	};
+};
+
+&omap3_pmx_core {
+	mmc3_pins: pinmux_mm3_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat4.sdmmc3_dat0 */
+			OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat5.sdmmc3_dat1 */
+			OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat2 */
+			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat3 */
+			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 */
+			OMAP3_CORE1_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
+			OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
+			OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3)	/* mcspi1_cs2.sdmmc_clk */
+		>;
+	};
+	mcbsp2_pins: pinmux_mcbsp2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)        /* mcbsp2_fsx */
+			OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)        /* mcbsp2_clkx */
+			OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0)        /* mcbsp2_dr */
+			OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0)       /* mcbsp2_dx */
+		>;
+	};
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0)	/* uart2_cts.uart2_cts */
+			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)	/* uart2_rts .uart2_rts*/
+			OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)	/* uart2_tx.uart2_tx */
+			OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)	/* uart2_rx.uart2_rx */
+			OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4)	/* GPIO_162,BT_EN */
+		>;
+	};
+	mcspi1_pins: pinmux_mcspi1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)        /* mcspi1_clk.mcspi1_clk */
+			OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0)       /* mcspi1_simo.mcspi1_simo */
+			OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
+			OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0)       /* mcspi1_cs0.mcspi1_cs0 */
+		>;
+	};
+	hsusb_otg_pins: pinmux_hsusb_otg_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0)	/* hsusb0_clk.hsusb0_clk */
+			OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0)	/* hsusb0_stp.hsusb0_stp */
+			OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0)	/* hsusb0_dir.hsusb0_dir */
+			OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0)	/* hsusb0_nxt.hsusb0_nxt */
+			OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0)	/* hsusb0_data0.hsusb0_data0 */
+			OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0)	/* hsusb0_data1.hsusb0_data1 */
+			OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0)	/* hsusb0_data2.hsusb0_data2 */
+			OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0)	/* hsusb0_data3.hsusb0_data3 */
+			OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0)	/* hsusb0_data4.hsusb0_data4 */
+			OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0)	/* hsusb0_data5.hsusb0_data5 */
+			OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0)	/* hsusb0_data6.hsusb0_data6 */
+			OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0)	/* hsusb0_data7.hsusb0_data7 */
+		>;
+	};
+};
+
+&uart2 {
+	interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+};
+
+&mcspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi1_pins>;
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&twl {
+	twl_power: power {
+		compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
+		ti,use_poweroff;
+	};
+};
+
+&twl_gpio {
+	ti,use-leds;
+};