Skip to content

L
linux
Commit ab9aad57 authored by Shawn Guo's avatar Shawn Guo
Browse files
Options

ARM: mxs: remove board files 

Since DT kernel provides the equivalent support with those board
files, we can remove them now.
Signed-off-by: default avatarShawn Guo <shawn.guo@linaro.org>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Lauri Hintsala <lauri.hintsala@bluegiga.com>
parent 44ffb78f
Expand all Hide whitespace changes
Inline Side-by-side
Showing with 0 additions and 1883 deletions
arch/arm/configs/mxs_defconfig
View file @ ab9aad57
...@@ -23,12 +23,6 @@ CONFIG_BLK_DEV_INTEGRITY=y ...@@ -23,12 +23,6 @@ CONFIG_BLK_DEV_INTEGRITY=y
# CONFIG_IOSCHED_CFQ is not set # CONFIG_IOSCHED_CFQ is not set
CONFIG_ARCH_MXS=y CONFIG_ARCH_MXS=y
CONFIG_MACH_MXS_DT=y CONFIG_MACH_MXS_DT=y
CONFIG_MACH_MX23EVK=y
CONFIG_MACH_MX28EVK=y
CONFIG_MACH_STMP378X_DEVB=y
CONFIG_MACH_TX28=y
CONFIG_MACH_M28EVK=y
CONFIG_MACH_APX4DEVKIT=y
# CONFIG_ARM_THUMB is not set # CONFIG_ARM_THUMB is not set
CONFIG_NO_HZ=y CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y CONFIG_HIGH_RES_TIMERS=y
......
arch/arm/mach-mxs/Kconfig
View file @ ab9aad57
...@@ -27,91 +27,4 @@ config MACH_MXS_DT ...@@ -27,91 +27,4 @@ config MACH_MXS_DT
Include support for Freescale MXS platforms(i.MX23 and i.MX28) Include support for Freescale MXS platforms(i.MX23 and i.MX28)
using the device tree for discovery using the device tree for discovery
config MACH_STMP378X_DEVB
bool "Support STMP378x_devb Platform"
select SOC_IMX23
select MXS_HAVE_AMBA_DUART
select MXS_HAVE_PLATFORM_AUART
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_RTC_STMP3XXX
help
Include support for STMP378x-devb platform. This includes specific
configurations for the board and its peripherals.
config MACH_MX23EVK
bool "Support MX23EVK Platform"
select SOC_IMX23
select MXS_HAVE_AMBA_DUART
select MXS_HAVE_PLATFORM_AUART
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_MXSFB
select MXS_HAVE_PLATFORM_RTC_STMP3XXX
help
Include support for MX23EVK platform. This includes specific
configurations for the board and its peripherals.
config MACH_MX28EVK
bool "Support MX28EVK Platform"
select SOC_IMX28
select LEDS_GPIO_REGISTER
select MXS_HAVE_AMBA_DUART
select MXS_HAVE_PLATFORM_AUART
select MXS_HAVE_PLATFORM_FEC
select MXS_HAVE_PLATFORM_FLEXCAN
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_MXSFB
select MXS_HAVE_PLATFORM_MXS_SAIF
select MXS_HAVE_PLATFORM_MXS_I2C
select MXS_HAVE_PLATFORM_RTC_STMP3XXX
help
Include support for MX28EVK platform. This includes specific
configurations for the board and its peripherals.
config MODULE_TX28
bool
select SOC_IMX28
select LEDS_GPIO_REGISTER
select MXS_HAVE_AMBA_DUART
select MXS_HAVE_PLATFORM_AUART
select MXS_HAVE_PLATFORM_FEC
select MXS_HAVE_PLATFORM_MXS_I2C
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_MXS_PWM
select MXS_HAVE_PLATFORM_RTC_STMP3XXX
config MODULE_M28
bool
select SOC_IMX28
select LEDS_GPIO_REGISTER
select MXS_HAVE_AMBA_DUART
select MXS_HAVE_PLATFORM_AUART
select MXS_HAVE_PLATFORM_FEC
select MXS_HAVE_PLATFORM_FLEXCAN
select MXS_HAVE_PLATFORM_MXS_I2C
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_MXSFB
config MODULE_APX4
bool
select SOC_IMX28
select LEDS_GPIO_REGISTER
select MXS_HAVE_AMBA_DUART
select MXS_HAVE_PLATFORM_AUART
select MXS_HAVE_PLATFORM_FEC
select MXS_HAVE_PLATFORM_MXS_I2C
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_MXS_SAIF
config MACH_TX28
bool "Ka-Ro TX28 module"
select MODULE_TX28
config MACH_M28EVK
bool "Support DENX M28EVK Platform"
select MODULE_M28
config MACH_APX4DEVKIT
bool "Support Bluegiga APX4 Development Kit"
select MODULE_APX4
endif endif
arch/arm/mach-mxs/Makefile
View file @ ab9aad57
...@@ -4,12 +4,5 @@ obj-y := devices.o icoll.o iomux.o ocotp.o system.o timer.o mm.o ...@@ -4,12 +4,5 @@ obj-y := devices.o icoll.o iomux.o ocotp.o system.o timer.o mm.o
obj-$(CONFIG_PM) += pm.o obj-$(CONFIG_PM) += pm.o
obj-$(CONFIG_MACH_MXS_DT) += mach-mxs.o obj-$(CONFIG_MACH_MXS_DT) += mach-mxs.o
obj-$(CONFIG_MACH_STMP378X_DEVB) += mach-stmp378x_devb.o
obj-$(CONFIG_MACH_MX23EVK) += mach-mx23evk.o
obj-$(CONFIG_MACH_MX28EVK) += mach-mx28evk.o
obj-$(CONFIG_MACH_M28EVK) += mach-m28evk.o
obj-$(CONFIG_MACH_APX4DEVKIT) += mach-apx4devkit.o
obj-$(CONFIG_MODULE_TX28) += module-tx28.o
obj-$(CONFIG_MACH_TX28) += mach-tx28.o
obj-y += devices/ obj-y += devices/
arch/arm/mach-mxs/mach-apx4devkit.c deleted 100644 → 0
View file @ 44ffb78f
/*
* Copyright (C) 2011-2012
* Lauri Hintsala, Bluegiga, <lauri.hintsala@bluegiga.com>
* Veli-Pekka Peltola, Bluegiga, <veli-pekka.peltola@bluegiga.com>
*
* based on: mach-mx28evk.c
* Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/leds.h>
#include <linux/clk.h>
#include <linux/i2c.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/fixed.h>
#include <linux/micrel_phy.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <mach/common.h>
#include <mach/digctl.h>
#include <mach/iomux-mx28.h>
#include "devices-mx28.h"
#define APX4DEVKIT_GPIO_USERLED MXS_GPIO_NR(3, 28)
static const iomux_cfg_t apx4devkit_pads[] __initconst = {
/* duart */
MX28_PAD_PWM0__DUART_RX | MXS_PAD_CTRL,
MX28_PAD_PWM1__DUART_TX | MXS_PAD_CTRL,
/* auart0 */
MX28_PAD_AUART0_RX__AUART0_RX | MXS_PAD_CTRL,
MX28_PAD_AUART0_TX__AUART0_TX | MXS_PAD_CTRL,
MX28_PAD_AUART0_CTS__AUART0_CTS | MXS_PAD_CTRL,
MX28_PAD_AUART0_RTS__AUART0_RTS | MXS_PAD_CTRL,
/* auart1 */
MX28_PAD_AUART1_RX__AUART1_RX | MXS_PAD_CTRL,
MX28_PAD_AUART1_TX__AUART1_TX | MXS_PAD_CTRL,
/* auart2 */
MX28_PAD_SSP2_SCK__AUART2_RX | MXS_PAD_CTRL,
MX28_PAD_SSP2_MOSI__AUART2_TX | MXS_PAD_CTRL,
/* auart3 */
MX28_PAD_SSP2_MISO__AUART3_RX | MXS_PAD_CTRL,
MX28_PAD_SSP2_SS0__AUART3_TX | MXS_PAD_CTRL,
#define MXS_PAD_FEC (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP)
/* fec0 */
MX28_PAD_ENET0_MDC__ENET0_MDC | MXS_PAD_FEC,
MX28_PAD_ENET0_MDIO__ENET0_MDIO | MXS_PAD_FEC,
MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MXS_PAD_FEC,
MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MXS_PAD_FEC,
MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MXS_PAD_FEC,
MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MXS_PAD_FEC,
MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MXS_PAD_FEC,
MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MXS_PAD_FEC,
MX28_PAD_ENET_CLK__CLKCTRL_ENET | MXS_PAD_FEC,
/* i2c */
MX28_PAD_I2C0_SCL__I2C0_SCL,
MX28_PAD_I2C0_SDA__I2C0_SDA,
/* mmc0 */
MX28_PAD_SSP0_DATA0__SSP0_D0 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA1__SSP0_D1 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA2__SSP0_D2 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA3__SSP0_D3 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA4__SSP0_D4 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA5__SSP0_D5 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA6__SSP0_D6 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA7__SSP0_D7 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_CMD__SSP0_CMD |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
MX28_PAD_SSP0_SCK__SSP0_SCK |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
/* led */
MX28_PAD_PWM3__GPIO_3_28 | MXS_PAD_CTRL,
/* saif0 & saif1 */
MX28_PAD_SAIF0_MCLK__SAIF0_MCLK |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
};
/* led */
static const struct gpio_led apx4devkit_leds[] __initconst = {
{
.name = "user-led",
.default_trigger = "heartbeat",
.gpio = APX4DEVKIT_GPIO_USERLED,
},
};
static const struct gpio_led_platform_data apx4devkit_led_data __initconst = {
.leds = apx4devkit_leds,
.num_leds = ARRAY_SIZE(apx4devkit_leds),
};
static const struct fec_platform_data mx28_fec_pdata __initconst = {
.phy = PHY_INTERFACE_MODE_RMII,
};
static const struct mxs_mmc_platform_data apx4devkit_mmc_pdata __initconst = {
.wp_gpio = -EINVAL,
.flags = SLOTF_4_BIT_CAPABLE,
};
static const struct i2c_board_info apx4devkit_i2c_boardinfo[] __initconst = {
{ I2C_BOARD_INFO("sgtl5000", 0x0a) }, /* ASoC */
{ I2C_BOARD_INFO("pcf8563", 0x51) }, /* RTC */
};
#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || \
defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
static struct regulator_consumer_supply apx4devkit_audio_consumer_supplies[] = {
REGULATOR_SUPPLY("VDDA", "0-000a"),
REGULATOR_SUPPLY("VDDIO", "0-000a"),
};
static struct regulator_init_data apx4devkit_vdd_reg_init_data = {
.constraints = {
.name = "3V3",
.always_on = 1,
},
.consumer_supplies = apx4devkit_audio_consumer_supplies,
.num_consumer_supplies = ARRAY_SIZE(apx4devkit_audio_consumer_supplies),
};
static struct fixed_voltage_config apx4devkit_vdd_pdata = {
.supply_name = "board-3V3",
.microvolts = 3300000,
.gpio = -EINVAL,
.enabled_at_boot = 1,
.init_data = &apx4devkit_vdd_reg_init_data,
};
static struct platform_device apx4devkit_voltage_regulator = {
.name = "reg-fixed-voltage",
.id = -1,
.num_resources = 0,
.dev = {
.platform_data = &apx4devkit_vdd_pdata,
},
};
static void __init apx4devkit_add_regulators(void)
{
platform_device_register(&apx4devkit_voltage_regulator);
}
#else
static void __init apx4devkit_add_regulators(void) {}
#endif
static const struct mxs_saif_platform_data
apx4devkit_mxs_saif_pdata[] __initconst = {
/* working on EXTMSTR0 mode (saif0 master, saif1 slave) */
{
.master_mode = 1,
.master_id = 0,
}, {
.master_mode = 0,
.master_id = 0,
},
};
static int apx4devkit_phy_fixup(struct phy_device *phy)
{
phy->dev_flags |= MICREL_PHY_50MHZ_CLK;
return 0;
}
static void __init apx4devkit_fec_phy_clk_enable(void)
{
struct clk *clk;
/* Enable fec phy clock */
clk = clk_get_sys("enet_out", NULL);
if (!IS_ERR(clk))
clk_prepare_enable(clk);
}
static void __init apx4devkit_init(void)
{
mx28_soc_init();
mxs_iomux_setup_multiple_pads(apx4devkit_pads,
ARRAY_SIZE(apx4devkit_pads));
mx28_add_duart();
mx28_add_auart0();
mx28_add_auart1();
mx28_add_auart2();
mx28_add_auart3();
/*
* Register fixup for the Micrel KS8031 PHY clock
* (shares same ID with KS8051)
*/
phy_register_fixup_for_uid(PHY_ID_KS8051, MICREL_PHY_ID_MASK,
apx4devkit_phy_fixup);
apx4devkit_fec_phy_clk_enable();
mx28_add_fec(0, &mx28_fec_pdata);
mx28_add_mxs_mmc(0, &apx4devkit_mmc_pdata);
gpio_led_register_device(0, &apx4devkit_led_data);
mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0);
mx28_add_saif(0, &apx4devkit_mxs_saif_pdata[0]);
mx28_add_saif(1, &apx4devkit_mxs_saif_pdata[1]);
apx4devkit_add_regulators();
mx28_add_mxs_i2c(0);
i2c_register_board_info(0, apx4devkit_i2c_boardinfo,
ARRAY_SIZE(apx4devkit_i2c_boardinfo));
mxs_add_platform_device("mxs-sgtl5000", 0, NULL, 0, NULL, 0);
}
static void __init apx4devkit_timer_init(void)
{
mx28_clocks_init();
}
static struct sys_timer apx4devkit_timer = {
.init = apx4devkit_timer_init,
};
MACHINE_START(APX4DEVKIT, "Bluegiga APX4 Development Kit")
.map_io = mx28_map_io,
.init_irq = mx28_init_irq,
.timer = &apx4devkit_timer,
.init_machine = apx4devkit_init,
.restart = mxs_restart,
MACHINE_END
arch/arm/mach-mxs/mach-m28evk.c deleted 100644 → 0
View file @ 44ffb78f
This diff is collapsed.
arch/arm/mach-mxs/mach-mx23evk.c deleted 100644 → 0
View file @ 44ffb78f
/*
* Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <mach/common.h>
#include <mach/iomux-mx23.h>
#include "devices-mx23.h"
#define MX23EVK_LCD_ENABLE MXS_GPIO_NR(1, 18)
#define MX23EVK_BL_ENABLE MXS_GPIO_NR(1, 28)
#define MX23EVK_MMC0_WRITE_PROTECT MXS_GPIO_NR(1, 30)
#define MX23EVK_MMC0_SLOT_POWER MXS_GPIO_NR(1, 29)
static const iomux_cfg_t mx23evk_pads[] __initconst = {
/* duart */
MX23_PAD_PWM0__DUART_RX | MXS_PAD_CTRL,
MX23_PAD_PWM1__DUART_TX | MXS_PAD_CTRL,
/* auart */
MX23_PAD_AUART1_RX__AUART1_RX | MXS_PAD_CTRL,
MX23_PAD_AUART1_TX__AUART1_TX | MXS_PAD_CTRL,
MX23_PAD_AUART1_CTS__AUART1_CTS | MXS_PAD_CTRL,
MX23_PAD_AUART1_RTS__AUART1_RTS | MXS_PAD_CTRL,
/* mxsfb (lcdif) */
MX23_PAD_LCD_D00__LCD_D00 | MXS_PAD_CTRL,
MX23_PAD_LCD_D01__LCD_D01 | MXS_PAD_CTRL,
MX23_PAD_LCD_D02__LCD_D02 | MXS_PAD_CTRL,
MX23_PAD_LCD_D03__LCD_D03 | MXS_PAD_CTRL,
MX23_PAD_LCD_D04__LCD_D04 | MXS_PAD_CTRL,
MX23_PAD_LCD_D05__LCD_D05 | MXS_PAD_CTRL,
MX23_PAD_LCD_D06__LCD_D06 | MXS_PAD_CTRL,
MX23_PAD_LCD_D07__LCD_D07 | MXS_PAD_CTRL,
MX23_PAD_LCD_D08__LCD_D08 | MXS_PAD_CTRL,
MX23_PAD_LCD_D09__LCD_D09 | MXS_PAD_CTRL,
MX23_PAD_LCD_D10__LCD_D10 | MXS_PAD_CTRL,
MX23_PAD_LCD_D11__LCD_D11 | MXS_PAD_CTRL,
MX23_PAD_LCD_D12__LCD_D12 | MXS_PAD_CTRL,
MX23_PAD_LCD_D13__LCD_D13 | MXS_PAD_CTRL,
MX23_PAD_LCD_D14__LCD_D14 | MXS_PAD_CTRL,
MX23_PAD_LCD_D15__LCD_D15 | MXS_PAD_CTRL,
MX23_PAD_LCD_D16__LCD_D16 | MXS_PAD_CTRL,
MX23_PAD_LCD_D17__LCD_D17 | MXS_PAD_CTRL,
MX23_PAD_GPMI_D08__LCD_D18 | MXS_PAD_CTRL,
MX23_PAD_GPMI_D09__LCD_D19 | MXS_PAD_CTRL,
MX23_PAD_GPMI_D10__LCD_D20 | MXS_PAD_CTRL,
MX23_PAD_GPMI_D11__LCD_D21 | MXS_PAD_CTRL,
MX23_PAD_GPMI_D12__LCD_D22 | MXS_PAD_CTRL,
MX23_PAD_GPMI_D13__LCD_D23 | MXS_PAD_CTRL,
MX23_PAD_LCD_VSYNC__LCD_VSYNC | MXS_PAD_CTRL,
MX23_PAD_LCD_HSYNC__LCD_HSYNC | MXS_PAD_CTRL,
MX23_PAD_LCD_DOTCK__LCD_DOTCK | MXS_PAD_CTRL,
MX23_PAD_LCD_ENABLE__LCD_ENABLE | MXS_PAD_CTRL,
/* LCD panel enable */
MX23_PAD_LCD_RESET__GPIO_1_18 | MXS_PAD_CTRL,
/* backlight control */
MX23_PAD_PWM2__GPIO_1_28 | MXS_PAD_CTRL,
/* mmc */
MX23_PAD_SSP1_DATA0__SSP1_DATA0 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DATA1__SSP1_DATA1 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DATA2__SSP1_DATA2 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DATA3__SSP1_DATA3 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_GPMI_D08__SSP1_DATA4 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_GPMI_D09__SSP1_DATA5 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_GPMI_D10__SSP1_DATA6 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_GPMI_D11__SSP1_DATA7 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_CMD__SSP1_CMD |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DETECT__SSP1_DETECT |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
MX23_PAD_SSP1_SCK__SSP1_SCK |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
/* write protect */
MX23_PAD_PWM4__GPIO_1_30 |
(MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
/* slot power enable */
MX23_PAD_PWM3__GPIO_1_29 |
(MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
};
/* mxsfb (lcdif) */
static struct fb_videomode mx23evk_video_modes[] = {
{
.name = "Samsung-LMS430HF02",
.refresh = 60,
.xres = 480,
.yres = 272,
.pixclock = 108096, /* picosecond (9.2 MHz) */
.left_margin = 15,
.right_margin = 8,
.upper_margin = 12,
.lower_margin = 4,
.hsync_len = 1,
.vsync_len = 1,
.sync = FB_SYNC_DATA_ENABLE_HIGH_ACT |
FB_SYNC_DOTCLK_FAILING_ACT,
},
};
static const struct mxsfb_platform_data mx23evk_mxsfb_pdata __initconst = {
.mode_list = mx23evk_video_modes,
.mode_count = ARRAY_SIZE(mx23evk_video_modes),
.default_bpp = 32,
.ld_intf_width = STMLCDIF_24BIT,
};
static struct mxs_mmc_platform_data mx23evk_mmc_pdata __initdata = {
.wp_gpio = MX23EVK_MMC0_WRITE_PROTECT,
.flags = SLOTF_8_BIT_CAPABLE,
};
static void __init mx23evk_init(void)
{
int ret;
mx23_soc_init();
mxs_iomux_setup_multiple_pads(mx23evk_pads, ARRAY_SIZE(mx23evk_pads));
mx23_add_duart();
mx23_add_auart0();
/* power on mmc slot by writing 0 to the gpio */
ret = gpio_request_one(MX23EVK_MMC0_SLOT_POWER, GPIOF_OUT_INIT_LOW,
"mmc0-slot-power");
if (ret)
pr_warn("failed to request gpio mmc0-slot-power: %d\n", ret);
mx23_add_mxs_mmc(0, &mx23evk_mmc_pdata);
ret = gpio_request_one(MX23EVK_LCD_ENABLE, GPIOF_DIR_OUT, "lcd-enable");
if (ret)
pr_warn("failed to request gpio lcd-enable: %d\n", ret);
else
gpio_set_value(MX23EVK_LCD_ENABLE, 1);
ret = gpio_request_one(MX23EVK_BL_ENABLE, GPIOF_DIR_OUT, "bl-enable");
if (ret)
pr_warn("failed to request gpio bl-enable: %d\n", ret);
else
gpio_set_value(MX23EVK_BL_ENABLE, 1);
mx23_add_mxsfb(&mx23evk_mxsfb_pdata);
mx23_add_rtc_stmp3xxx();
}
static void __init mx23evk_timer_init(void)
{
mx23_clocks_init();
}
static struct sys_timer mx23evk_timer = {
.init = mx23evk_timer_init,
};
MACHINE_START(MX23EVK, "Freescale MX23 EVK")
/* Maintainer: Freescale Semiconductor, Inc. */
.map_io = mx23_map_io,
.init_irq = mx23_init_irq,
.timer = &mx23evk_timer,
.init_machine = mx23evk_init,
.restart = mxs_restart,
MACHINE_END
arch/arm/mach-mxs/mach-mx28evk.c deleted 100644 → 0
View file @ 44ffb78f
This diff is collapsed.
arch/arm/mach-mxs/mach-stmp378x_devb.c deleted 100644 → 0
View file @ 44ffb78f
/*
* board setup for STMP378x-Development-Board
*
* based on mx23evk board setup and information gained form the original
* plat-stmp based board setup, now converted to mach-mxs.
*
* Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
* Copyright (C) 2011 Wolfram Sang, Pengutronix e.K.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/spi/spi.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <mach/common.h>
#include <mach/iomux-mx23.h>
#include "devices-mx23.h"
#define STMP378X_DEVB_MMC0_WRITE_PROTECT MXS_GPIO_NR(1, 30)
#define STMP378X_DEVB_MMC0_SLOT_POWER MXS_GPIO_NR(1, 29)
#define STMP378X_DEVB_PAD_AUART (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_NOPULL)
static const iomux_cfg_t stmp378x_dvb_pads[] __initconst = {
/* duart (extended setup missing in old boardcode, too */
MX23_PAD_PWM0__DUART_RX,
MX23_PAD_PWM1__DUART_TX,
/* auart */
MX23_PAD_AUART1_RX__AUART1_RX | STMP378X_DEVB_PAD_AUART,
MX23_PAD_AUART1_TX__AUART1_TX | STMP378X_DEVB_PAD_AUART,
MX23_PAD_AUART1_CTS__AUART1_CTS | STMP378X_DEVB_PAD_AUART,
MX23_PAD_AUART1_RTS__AUART1_RTS | STMP378X_DEVB_PAD_AUART,
/* mmc */
MX23_PAD_SSP1_DATA0__SSP1_DATA0 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DATA1__SSP1_DATA1 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DATA2__SSP1_DATA2 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DATA3__SSP1_DATA3 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_CMD__SSP1_CMD |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DETECT__SSP1_DETECT |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
MX23_PAD_SSP1_SCK__SSP1_SCK |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
MX23_PAD_PWM4__GPIO_1_30 | MXS_PAD_CTRL, /* write protect */
MX23_PAD_PWM3__GPIO_1_29 | MXS_PAD_CTRL, /* power enable */
};
static struct mxs_mmc_platform_data stmp378x_dvb_mmc_pdata __initdata = {
.wp_gpio = STMP378X_DEVB_MMC0_WRITE_PROTECT,
};
static struct spi_board_info spi_board_info[] __initdata = {
#if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
{
.modalias = "enc28j60",
.max_speed_hz = 6 * 1000 * 1000,
.bus_num = 1,
.chip_select = 0,
.platform_data = NULL,
},
#endif
};
static void __init stmp378x_dvb_init(void)
{
int ret;
mx23_soc_init();
mxs_iomux_setup_multiple_pads(stmp378x_dvb_pads,
ARRAY_SIZE(stmp378x_dvb_pads));
mx23_add_duart();
mx23_add_auart0();
mx23_add_rtc_stmp3xxx();
/* power on mmc slot */
ret = gpio_request_one(STMP378X_DEVB_MMC0_SLOT_POWER,
GPIOF_OUT_INIT_LOW, "mmc0-slot-power");
if (ret)
pr_warn("could not power mmc (%d)\n", ret);
mx23_add_mxs_mmc(0, &stmp378x_dvb_mmc_pdata);
spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
}
static void __init stmp378x_dvb_timer_init(void)
{
mx23_clocks_init();
}
static struct sys_timer stmp378x_dvb_timer = {
.init = stmp378x_dvb_timer_init,
};
MACHINE_START(STMP378X, "STMP378X")
.map_io = mx23_map_io,
.init_irq = mx23_init_irq,
.timer = &stmp378x_dvb_timer,
.init_machine = stmp378x_dvb_init,
.restart = mxs_restart,
MACHINE_END
arch/arm/mach-mxs/mach-tx28.c deleted 100644 → 0
View file @ 44ffb78f
/*
* Copyright (C) 2010 <LW@KARO-electronics.de>
*
* based on: mach-mx28_evk.c
* Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation
*/
#include <linux/kernel.h>
#include <linux/gpio.h>
#include <linux/leds.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi_gpio.h>
#include <linux/i2c.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <mach/common.h>
#include <mach/iomux-mx28.h>
#include "devices-mx28.h"
#include "module-tx28.h"
#define TX28_STK5_GPIO_LED MXS_GPIO_NR(4, 10)
static const iomux_cfg_t tx28_stk5v3_pads[] __initconst = {
/* LED */
MX28_PAD_ENET0_RXD3__GPIO_4_10 |
MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_NOPULL,
/* framebuffer */
#define LCD_MODE (MXS_PAD_3V3 | MXS_PAD_4MA)
MX28_PAD_LCD_D00__LCD_D0 | LCD_MODE,
MX28_PAD_LCD_D01__LCD_D1 | LCD_MODE,
MX28_PAD_LCD_D02__LCD_D2 | LCD_MODE,
MX28_PAD_LCD_D03__LCD_D3 | LCD_MODE,
MX28_PAD_LCD_D04__LCD_D4 | LCD_MODE,
MX28_PAD_LCD_D05__LCD_D5 | LCD_MODE,
MX28_PAD_LCD_D06__LCD_D6 | LCD_MODE,
MX28_PAD_LCD_D07__LCD_D7 | LCD_MODE,
MX28_PAD_LCD_D08__LCD_D8 | LCD_MODE,
MX28_PAD_LCD_D09__LCD_D9 | LCD_MODE,
MX28_PAD_LCD_D10__LCD_D10 | LCD_MODE,
MX28_PAD_LCD_D11__LCD_D11 | LCD_MODE,
MX28_PAD_LCD_D12__LCD_D12 | LCD_MODE,
MX28_PAD_LCD_D13__LCD_D13 | LCD_MODE,
MX28_PAD_LCD_D14__LCD_D14 | LCD_MODE,
MX28_PAD_LCD_D15__LCD_D15 | LCD_MODE,
MX28_PAD_LCD_D16__LCD_D16 | LCD_MODE,
MX28_PAD_LCD_D17__LCD_D17 | LCD_MODE,
MX28_PAD_LCD_D18__LCD_D18 | LCD_MODE,
MX28_PAD_LCD_D19__LCD_D19 | LCD_MODE,
MX28_PAD_LCD_D20__LCD_D20 | LCD_MODE,
MX28_PAD_LCD_D21__LCD_D21 | LCD_MODE,
MX28_PAD_LCD_D22__LCD_D22 | LCD_MODE,
MX28_PAD_LCD_D23__LCD_D23 | LCD_MODE,
MX28_PAD_LCD_RD_E__LCD_VSYNC | LCD_MODE,
MX28_PAD_LCD_WR_RWN__LCD_HSYNC | LCD_MODE,
MX28_PAD_LCD_RS__LCD_DOTCLK | LCD_MODE,
MX28_PAD_LCD_CS__LCD_CS | LCD_MODE,
MX28_PAD_LCD_VSYNC__LCD_VSYNC | LCD_MODE,
MX28_PAD_LCD_HSYNC__LCD_HSYNC | LCD_MODE,
MX28_PAD_LCD_DOTCLK__LCD_DOTCLK | LCD_MODE,
MX28_PAD_LCD_ENABLE__GPIO_1_31 | LCD_MODE,
MX28_PAD_LCD_RESET__GPIO_3_30 | LCD_MODE,
MX28_PAD_PWM0__PWM_0 | LCD_MODE,
/* UART1 */
MX28_PAD_AUART0_CTS__DUART_RX,
MX28_PAD_AUART0_RTS__DUART_TX,
MX28_PAD_AUART0_TX__DUART_RTS,
MX28_PAD_AUART0_RX__DUART_CTS,
/* UART2 */
MX28_PAD_AUART1_RX__AUART1_RX,
MX28_PAD_AUART1_TX__AUART1_TX,
MX28_PAD_AUART1_RTS__AUART1_RTS,
MX28_PAD_AUART1_CTS__AUART1_CTS,
/* CAN */
MX28_PAD_GPMI_RDY2__CAN0_TX,
MX28_PAD_GPMI_RDY3__CAN0_RX,
/* I2C */
MX28_PAD_I2C0_SCL__I2C0_SCL,
MX28_PAD_I2C0_SDA__I2C0_SDA,
/* TSC2007 */
MX28_PAD_SAIF0_MCLK__GPIO_3_20 | MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_PULLUP,
/* MMC0 */
MX28_PAD_SSP0_DATA0__SSP0_D0 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA1__SSP0_D1 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA2__SSP0_D2 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA3__SSP0_D3 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_CMD__SSP0_CMD |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
MX28_PAD_SSP0_SCK__SSP0_SCK |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
};
static const struct gpio_led tx28_stk5v3_leds[] __initconst = {
{
.name = "GPIO-LED",
.default_trigger = "heartbeat",
.gpio = TX28_STK5_GPIO_LED,
},
};
static const struct gpio_led_platform_data tx28_stk5v3_led_data __initconst = {
.leds = tx28_stk5v3_leds,
.num_leds = ARRAY_SIZE(tx28_stk5v3_leds),
};
static struct spi_board_info tx28_spi_board_info[] = {
{
.modalias = "spidev",
.max_speed_hz = 20000000,
.bus_num = 0,
.chip_select = 1,
.controller_data = (void *)SPI_GPIO_NO_CHIPSELECT,
.mode = SPI_MODE_0,
},
};
static struct i2c_board_info tx28_stk5v3_i2c_boardinfo[] __initdata = {
{
I2C_BOARD_INFO("ds1339", 0x68),
},
};
static struct mxs_mmc_platform_data tx28_mmc0_pdata __initdata = {
.wp_gpio = -EINVAL,
.flags = SLOTF_4_BIT_CAPABLE,
};
static void __init tx28_stk5v3_init(void)
{
mx28_soc_init();
mxs_iomux_setup_multiple_pads(tx28_stk5v3_pads,
ARRAY_SIZE(tx28_stk5v3_pads));
mx28_add_duart(); /* UART1 */
mx28_add_auart(1); /* UART2 */
tx28_add_fec0();
/* spi via ssp will be added when available */
spi_register_board_info(tx28_spi_board_info,
ARRAY_SIZE(tx28_spi_board_info));
gpio_led_register_device(0, &tx28_stk5v3_led_data);
mx28_add_mxs_i2c(0);
i2c_register_board_info(0, tx28_stk5v3_i2c_boardinfo,
ARRAY_SIZE(tx28_stk5v3_i2c_boardinfo));
mx28_add_mxs_mmc(0, &tx28_mmc0_pdata);
mx28_add_rtc_stmp3xxx();
}
static void __init tx28_timer_init(void)
{
mx28_clocks_init();
}
static struct sys_timer tx28_timer = {
.init = tx28_timer_init,
};
MACHINE_START(TX28, "Ka-Ro electronics TX28 module")
.map_io = mx28_map_io,
.init_irq = mx28_init_irq,
.timer = &tx28_timer,
.init_machine = tx28_stk5v3_init,
.restart = mxs_restart,
MACHINE_END
arch/arm/mach-mxs/module-tx28.c deleted 100644 → 0
View file @ 44ffb78f
/*
* Copyright (C) 2010 <LW@KARO-electronics.de>
*
* This program is free software; you can redistribute it and/or modify it under
* the terms of the GNU General Public License version 2 as published by the
* Free Software Foundation.
*/
#include <linux/delay.h>
#include <linux/fec.h>
#include <linux/gpio.h>
#include <mach/iomux-mx28.h>
#include "devices-mx28.h"
#include "module-tx28.h"
#define TX28_FEC_PHY_POWER MXS_GPIO_NR(3, 29)
#define TX28_FEC_PHY_RESET MXS_GPIO_NR(4, 13)
static const iomux_cfg_t tx28_fec_gpio_pads[] __initconst = {
/* PHY POWER */
MX28_PAD_PWM4__GPIO_3_29 |
MXS_PAD_4MA | MXS_PAD_NOPULL | MXS_PAD_3V3,
/* PHY RESET */
MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
MXS_PAD_4MA | MXS_PAD_NOPULL | MXS_PAD_3V3,
/* Mode strap pins 0-2 */
MX28_PAD_ENET0_RXD0__GPIO_4_3 |
MXS_PAD_8MA | MXS_PAD_PULLUP | MXS_PAD_3V3,
MX28_PAD_ENET0_RXD1__GPIO_4_4 |
MXS_PAD_8MA | MXS_PAD_PULLUP | MXS_PAD_3V3,
MX28_PAD_ENET0_RX_EN__GPIO_4_2 |
MXS_PAD_8MA | MXS_PAD_PULLUP | MXS_PAD_3V3,
/* nINT */
MX28_PAD_ENET0_TX_CLK__GPIO_4_5 |
MXS_PAD_4MA | MXS_PAD_NOPULL | MXS_PAD_3V3,
MX28_PAD_ENET0_MDC__GPIO_4_0,
MX28_PAD_ENET0_MDIO__GPIO_4_1,
MX28_PAD_ENET0_TX_EN__GPIO_4_6,
MX28_PAD_ENET0_TXD0__GPIO_4_7,
MX28_PAD_ENET0_TXD1__GPIO_4_8,
MX28_PAD_ENET_CLK__GPIO_4_16,
};
#define FEC_MODE (MXS_PAD_8MA | MXS_PAD_PULLUP | MXS_PAD_3V3)
static const iomux_cfg_t tx28_fec0_pads[] __initconst = {
MX28_PAD_ENET0_MDC__ENET0_MDC | FEC_MODE,
MX28_PAD_ENET0_MDIO__ENET0_MDIO | FEC_MODE,
MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | FEC_MODE,
MX28_PAD_ENET0_RXD0__ENET0_RXD0 | FEC_MODE,
MX28_PAD_ENET0_RXD1__ENET0_RXD1 | FEC_MODE,
MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | FEC_MODE,
MX28_PAD_ENET0_TXD0__ENET0_TXD0 | FEC_MODE,
MX28_PAD_ENET0_TXD1__ENET0_TXD1 | FEC_MODE,
MX28_PAD_ENET_CLK__CLKCTRL_ENET | FEC_MODE,
};
static const iomux_cfg_t tx28_fec1_pads[] __initconst = {
MX28_PAD_ENET0_RXD2__ENET1_RXD0,
MX28_PAD_ENET0_RXD3__ENET1_RXD1,
MX28_PAD_ENET0_TXD2__ENET1_TXD0,
MX28_PAD_ENET0_TXD3__ENET1_TXD1,
MX28_PAD_ENET0_COL__ENET1_TX_EN,
MX28_PAD_ENET0_CRS__ENET1_RX_EN,
};
static const struct fec_platform_data tx28_fec0_data __initconst = {
.phy = PHY_INTERFACE_MODE_RMII,
};
static const struct fec_platform_data tx28_fec1_data __initconst = {
.phy = PHY_INTERFACE_MODE_RMII,
};
int __init tx28_add_fec0(void)
{
int i, ret;
pr_debug("%s: Switching FEC PHY power off\n", __func__);
ret = mxs_iomux_setup_multiple_pads(tx28_fec_gpio_pads,
ARRAY_SIZE(tx28_fec_gpio_pads));
for (i = 0; i < ARRAY_SIZE(tx28_fec_gpio_pads); i++) {
unsigned int gpio = MXS_GPIO_NR(PAD_BANK(tx28_fec_gpio_pads[i]),
PAD_PIN(tx28_fec_gpio_pads[i]));
ret = gpio_request(gpio, "FEC");
if (ret) {
pr_err("Failed to request GPIO_%d_%d: %d\n",
PAD_BANK(tx28_fec_gpio_pads[i]),
PAD_PIN(tx28_fec_gpio_pads[i]), ret);
goto free_gpios;
}
ret = gpio_direction_output(gpio, 0);
if (ret) {
pr_err("Failed to set direction of GPIO_%d_%d to output: %d\n",
gpio / 32 + 1, gpio % 32, ret);
goto free_gpios;
}
}
/* Power up fec phy */
pr_debug("%s: Switching FEC PHY power on\n", __func__);
ret = gpio_direction_output(TX28_FEC_PHY_POWER, 1);
if (ret) {
pr_err("Failed to power on PHY: %d\n", ret);
goto free_gpios;
}
mdelay(26); /* 25ms according to data sheet */
/* nINT */
gpio_direction_input(MXS_GPIO_NR(4, 5));
/* Mode strap pins */
gpio_direction_output(MXS_GPIO_NR(4, 2), 1);
gpio_direction_output(MXS_GPIO_NR(4, 3), 1);
gpio_direction_output(MXS_GPIO_NR(4, 4), 1);
udelay(100); /* minimum assertion time for nRST */
pr_debug("%s: Deasserting FEC PHY RESET\n", __func__);
gpio_set_value(TX28_FEC_PHY_RESET, 1);
ret = mxs_iomux_setup_multiple_pads(tx28_fec0_pads,
ARRAY_SIZE(tx28_fec0_pads));
if (ret) {
pr_debug("%s: mxs_iomux_setup_multiple_pads() failed with rc: %d\n",
__func__, ret);
goto free_gpios;
}
pr_debug("%s: Registering FEC0 device\n", __func__);
mx28_add_fec(0, &tx28_fec0_data);
return 0;
free_gpios:
while (--i >= 0) {
unsigned int gpio = MXS_GPIO_NR(PAD_BANK(tx28_fec_gpio_pads[i]),
PAD_PIN(tx28_fec_gpio_pads[i]));
gpio_free(gpio);
}
return ret;
}
int __init tx28_add_fec1(void)
{
int ret;
ret = mxs_iomux_setup_multiple_pads(tx28_fec1_pads,
ARRAY_SIZE(tx28_fec1_pads));
if (ret) {
pr_debug("%s: mxs_iomux_setup_multiple_pads() failed with rc: %d\n",
__func__, ret);
return ret;
}
pr_debug("%s: Registering FEC1 device\n", __func__);
mx28_add_fec(1, &tx28_fec1_data);
return 0;
}
arch/arm/mach-mxs/module-tx28.h deleted 100644 → 0
View file @ 44ffb78f
/*
* Copyright (C) 2010 Pengutronix
* Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
*
* This program is free software; you can redistribute it and/or modify it under
* the terms of the GNU General Public License version 2 as published by the
* Free Software Foundation.
*/
int __init tx28_add_fec0(void);
int __init tx28_add_fec1(void);
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7