Merge suse.cz:/home/vojtech/bk/linus into suse.cz:/home/vojtech/bk/input

Documentation/input/joystick-parport.txt

@@ -434,7 +434,7 @@ Here are described their command lines:
   Using gamecon.c you can connect up to five devices to one parallel port. It
 uses the following kernel/module command line:
 
-	gc=port,pad1,pad2,pad3,pad4,pad5
+	gamecon.map=port,pad1,pad2,pad3,pad4,pad5
 
   Where 'port' the number of the parport interface (eg. 0 for parport0).
 
@@ -457,15 +457,15 @@ uses the following kernel/module command line:
 your controller plugged in before initializing.
 
   Should you want to use more than one of parallel ports at once, you can use
-gc_2 and gc_3 as additional command line parameters for two more parallel
-ports.
+gamecon.map2 and gamecon.map3 as additional command line parameters for two
+more parallel ports.
 
 3.2 db9.c
 ~~~~~~~~~
   Apart from making an interface, there is nothing difficult on using the
 db9.c driver. It uses the following kernel/module command line:
 
-	db9=port,type
+	db9.dev=port,type
 
   Where 'port' is the number of the parport interface (eg. 0 for parport0).
 
@@ -489,14 +489,14 @@ Old parallel ports may not have this feature.
 	 10  | Amiga CD32 pad
 
   Should you want to use more than one of these joysticks/pads at once, you
-can use db9_2 and db9_3 as additional command line parameters for two
+can use db9.dev2 and db9.dev3 as additional command line parameters for two
 more joysticks/pads.
 
 3.3 turbografx.c
 ~~~~~~~~~~~~~~~~
   The turbografx.c driver uses a very simple kernel/module command line:
 
-	tgfx=port,js1,js2,js3,js4,js5,js6,js7
+	turbografx.map=port,js1,js2,js3,js4,js5,js6,js7
 
   Where 'port' is the number of the parport interface (eg. 0 for parport0).
 
@@ -504,8 +504,8 @@ more joysticks/pads.
 interface ports 1-7 have. For a standard multisystem joystick, this is 1.
 
   Should you want to use more than one of these interfaces at once, you can
-use tgfx_2 and tgfx_3 as additional command line parameters for two more
-interfaces.
+use turbografx.map2 and turbografx.map3 as additional command line parameters
+for two more interfaces.
 
 3.4 PC parallel port pinout
 ~~~~~~~~~~~~~~~~~~~~~~~~~~~

Documentation/input/joystick.txt

@@ -111,7 +111,7 @@ your needs:
 	alias tty-ldisc-2 serport
 	alias char-major-13 input
 	above input joydev ns558 analog
-	options analog js=gamepad
+	options analog map=gamepad,none,2btn
 
 2.5 Verifying that it works
 ~~~~~~~~~~~~~~~~~~~~~~~~~~~
@@ -185,7 +185,7 @@ you'll need to specify the types either on the kernel command line or on the
 module command line, when inserting analog.o into the kernel. The
 parameters are:
 
-	js=type,type,type,....
+	analog.map=<type1>,<type2>,<type3>,....
 
   'type' is type of the joystick from the table below, defining joysticks
 present on gameports in the system, starting with gameport0, second 'type'
@@ -419,7 +419,7 @@ card.
   Amiga joysticks, connected to an Amiga, are supported by the amijoy.c
 driver. Since they can't be autodetected, the driver has a command line.
 
-	amijoy=a,b
+	amijoy.map=<a>,<b>
 
   a and b define the joysticks connected to the JOY0DAT and JOY1DAT ports of
 the Amiga.

Documentation/kernel-parameters.txt

@@ -151,7 +151,15 @@ running once the system is up.
 			Format: <host-scsi-id>,<target-scsi-id>,<max-rate>,<max-offset>
 			See also header of drivers/scsi/AM53C974.c.
 
-	amijoy=		[HW,JOY] Amiga joystick support 
+	amijoy.map=	[HW,JOY] Amiga joystick support
+			Map of devices attached to JOY0DAT and JOY1DAT
+			Format: <a>,<b>
+			See also Documentation/kernel/input/joystick.txt
+
+	analog.map=	[HW,JOY] Analog joystick and gamepad support
+			Specifies type or capabilities of an analog joystick
+			connected to one of 16 gameports
+			Format: <type1>,<type2>,..<type16>
 
 	apc=		[HW,SPARC] Power management functions (SPARCstation-4/5 + deriv.)
 			Format: noidle
@@ -174,11 +182,18 @@ running once the system is up.
 
 	atascsi=	[HW,SCSI] Atari SCSI
 
-	atkbd.set=	[HW] Select keyboard code set
-			Format: <int>
+	atkbd.extra=	[HW] Enable extra LEDs and keys on IBM RapidAccess, EzKey
+			and similar keyboards
+
+	atkbd.reset=	[HW] Reset keyboard during initialization
+
+	atkbd.set=	[HW] Select keyboard code set 
+			Format: <int> (2 = AT (default) 3 = PS/2)
+
+	atkbd.scroll=	[HW] Enable scroll wheel on MS Office and similar keyboards
+	
 	atkbd.softrepeat=
 			[HW] Use software keyboard repeat
-	atkbd.reset=	[HW] Reset keyboard during initialization
 
 	autotest	[IA64]
 
@@ -280,10 +295,11 @@ running once the system is up.
 	dasd=		[HW,NET]    
 			See header of drivers/s390/block/dasd_devmap.c.
 
-	db9=		[HW,JOY]
-	db9_2=
-	db9_3=
- 
+	db9.dev[2|3]=	[HW,JOY] Multisystem joystick support via parallel port
+			(one device per port)
+			Format: <port#>,<type>
+			See also Documentation/input/joystick-parport.txt
+
 	debug		[KNL] Enable kernel debugging (events log level).
 
 	decnet=		[HW,NET]
@@ -377,12 +393,14 @@ running once the system is up.
 	ftape=		[HW] Floppy Tape subsystem debugging options.
 			See Documentation/ftape.txt.
 
+	gamecon.map[2|3]=
+			[HW,JOY] Multisystem joystick and NES/SNES/PSX pad
+			support via parallel port (up to 5 devices per port)
+			Format: <port#>,<pad1>,<pad2>,<pad3>,<pad4>,<pad5>
+			See also Documentation/input/joystick-parport.txt
+
 	gamma=		[HW,DRM]
 
-	gc=		[HW,JOY]
-	gc_2=		See Documentation/input/joystick-parport.txt.
-	gc_3=		
- 
 	gdth=		[HW,SCSI]
 			See header of drivers/scsi/gdth.c.
 
@@ -609,9 +627,9 @@ running once the system is up.
 
 	mga=		[HW,DRM]
 
-	mousedev.xres	[MOUSE] Horizontal screen resolution, used for devices
+	mousedev.xres=	[MOUSE] Horizontal screen resolution, used for devices
 			reporting absolute coordinates, such as tablets
-	mousedev.yres	[MOUSE] Vertical screen resolution, used for devices
+	mousedev.yres=	[MOUSE] Vertical screen resolution, used for devices
 			reporting absolute coordinates, such as tablets
 
 	mpu401=		[HW,OSS]
@@ -1156,10 +1174,6 @@ running once the system is up.
 			See header of drivers/scsi/t128.c.
 
 	tdfx=		[HW,DRM]
- 
-	tgfx=		[HW,JOY] TurboGraFX parallel port interface
-	tgfx_2=		See Documentation/input/joystick-parport.txt.
-	tgfx_3=
 
 	thash_entries=	[KNL,NET]
 			Set number of hash buckets for TCP connection
@@ -1182,8 +1196,13 @@ running once the system is up.
 	trix=		[HW,OSS] MediaTrix AudioTrix Pro
 			Format: <io>,<irq>,<dma>,<dma2>,<sb_io>,<sb_irq>,<sb_dma>,<mpu_io>,<mpu_irq>
  
-	tsdev.xres	[TS] Horizontal screen resolution.
-	tsdev.yres	[TS] Vertical screen resolution.
+	tsdev.xres=	[TS] Horizontal screen resolution.
+	tsdev.yres=	[TS] Vertical screen resolution.
+
+	turbografx.map[2|3]=
+			[HW,JOY] TurboGraFX parallel port interface
+			Format: <port#>,<js1>,<js2>,<js3>,<js4>,<js5>,<js6>,<js7>
+			See also Documentation/input/joystick-parport.txt
 
 	u14-34f=	[HW,SCSI] UltraStor 14F/34F SCSI host adapter
 			See header of drivers/scsi/u14-34f.c.

Documentation/usb/acm.txt

@@ -28,7 +28,7 @@ in the package: See the file COPYING.
 
 1. Usage
 ~~~~~~~~
-  The drivers/usb/acm.c drivers works with USB modems and USB ISDN terminal
+  The drivers/usb/class/cdc-acm.c drivers works with USB modems and USB ISDN terminal
 adapters that conform to the Universal Serial Bus Communication Device Class
 Abstract Control Model (USB CDC ACM) specification.
 
@@ -65,9 +65,9 @@ minor/major numbers anywhere you want, but either the above location or
 
   To use the modems you need these modules loaded:
 
-	usbcore.o
-	usb-[uo]hci.o or uhci.o
-	acm.o
+	usbcore.ko
+	uhci-hcd.ko ohci-hcd.ko or ehci-hcd.ko
+	cdc-acm.ko
 
   After that, the modem[s] should be accessible. You should be able to use
 minicom, ppp and mgetty with them.

arch/arm26/Kconfig

@@ -198,11 +198,6 @@ source "drivers/input/Kconfig"
 
 source "drivers/char/Kconfig"
 
-config KBDMOUSE
-	bool
-	depends on ARCH_ACORN && BUSMOUSE=y
-	default y
-
 source "drivers/media/Kconfig"
 
 source "fs/Kconfig"

drivers/char/Kconfig

@@ -599,30 +599,6 @@ config PC9800_OLDLP_CONSOLE
 	bool "Support for console on line printer"
 	depends on PC9800_OLDLP
 
-
-menu "Mice"
-
-config BUSMOUSE
-	tristate "Bus Mouse Support"
-	---help---
-	  Say Y here if your machine has a bus mouse as opposed to a serial
-	  mouse. Most people have a regular serial MouseSystem or
-	  Microsoft mouse (made by Logitech) that plugs into a COM port
-	  (rectangular with 9 or 25 pins). These people say N here. 
-
-	  If you have a laptop, you either have to check the documentation or
-	  experiment a bit to find out whether the trackball is a serial mouse
-	  or not; it's best to say Y here for you.
-
-	  This is the generic bus mouse driver code. If you have a bus mouse,
-	  you will have to say Y here and also to the specific driver for your
-	  mouse below.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called busmouse.
-
-endmenu
-
 config QIC02_TAPE
 	tristate "QIC-02 tape support"
 	help

drivers/char/Makefile

@@ -49,7 +49,6 @@ obj-$(CONFIG_PRINTER) += lp.o
 obj-$(CONFIG_TIPAR) += tipar.o
 obj-$(CONFIG_PC9800_OLDLP) += lp_old98.o
 
-obj-$(CONFIG_BUSMOUSE) += busmouse.o
 obj-$(CONFIG_DTLK) += dtlk.o
 obj-$(CONFIG_R3964) += n_r3964.o
 obj-$(CONFIG_APPLICOM) += applicom.o

drivers/input/evdev.c

@@ -209,7 +209,7 @@ static int evdev_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
 	struct evdev *evdev = list->evdev;
 	struct input_dev *dev = evdev->handle.dev;
 	struct input_absinfo abs;
-	int t, u, v;
+	int i, t, u, v;
 
 	if (!evdev->exist) return -ENODEV;
 
@@ -234,6 +234,9 @@ static int evdev_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
 			u = SET_INPUT_KEYCODE(dev, t, v);
 			clear_bit(u, dev->keybit);
 			set_bit(v, dev->keybit);
+			for (i = 0; i < dev->keycodemax; i++)
+				if (INPUT_KEYCODE(dev,i) == u)
+					set_bit(u, dev->keybit);
 			return 0;
 
 		case EVIOCSFF:

drivers/input/gameport/ns558.c

@@ -77,7 +77,7 @@ static void ns558_isa_probe(int io)
  * No one should be using this address.
  */
 
-	if (check_region(io, 1))
+	if (!request_region(io, 1, "ns558-isa"))
 		return;
 
 /*
@@ -89,7 +89,8 @@ static void ns558_isa_probe(int io)
 	outb(~c & ~3, io);
 	if (~(u = v = inb(io)) & 3) {
 		outb(c, io);
-		return;
+		i = 0;
+		goto out;
 	}
 /*
  * After a trigger, there must be at least some bits changing.
@@ -99,7 +100,8 @@ static void ns558_isa_probe(int io)
 
 	if (u == v) {
 		outb(c, io);
-		return;
+		i = 0;
+		goto out;
 	}
 	wait_ms(3);
 /*
@@ -110,7 +112,8 @@ static void ns558_isa_probe(int io)
 	for (i = 0; i < 1000; i++)
 		if ((u ^ inb(io)) & 0xf) {
 			outb(c, io);
-			return;
+			i = 0;
+			goto out;
 		}
 /* 
  * And now find the number of mirrors of the port.
@@ -118,7 +121,9 @@ static void ns558_isa_probe(int io)
 
 	for (i = 1; i < 5; i++) {
 
-		if (check_region(io & (-1 << i), (1 << i)))	/* Don't disturb anyone */
+		release_region(io & (-1 << (i-1)), (1 << (i-1)));
+
+		if (!request_region(io & (-1 << i), (1 << i), "ns558-isa"))	/* Don't disturb anyone */
 			break;
 
 		outb(0xff, io & (-1 << i));
@@ -126,18 +131,25 @@ static void ns558_isa_probe(int io)
 			if (inb(io & (-1 << i)) != inb((io & (-1 << i)) + (1 << i) - 1)) b++;
 		wait_ms(3);
 
-		if (b > 300)					/* We allow 30% difference */
+		if (b > 300) {					/* We allow 30% difference */
+			release_region(io & (-1 << i), (1 << i));
 			break;
+		}
 	}
 
 	i--;
 
+	if (i != 4) {
+		if (!request_region(io & (-1 << i), (1 << i), "ns558-isa"))
+			return;
+	}
+
 	if (!(port = kmalloc(sizeof(struct ns558), GFP_KERNEL))) {
 		printk(KERN_ERR "ns558: Memory allocation failed.\n");
-		return;
+		goto out;
 	}
-       	memset(port, 0, sizeof(struct ns558));
-	
+	memset(port, 0, sizeof(struct ns558));
+
 	port->type = NS558_ISA;
 	port->size = (1 << i);
 	port->gameport.io = io;
@@ -148,8 +160,6 @@ static void ns558_isa_probe(int io)
 	sprintf(port->phys, "isa%04x/gameport0", io & (-1 << i));
 	sprintf(port->name, "NS558 ISA");
 
-	request_region(io & (-1 << i), (1 << i), "ns558-isa");
-
 	gameport_register_port(&port->gameport);
 
 	printk(KERN_INFO "gameport: NS558 ISA at %#x", port->gameport.io);
@@ -157,6 +167,9 @@ static void ns558_isa_probe(int io)
 	printk(" speed %d kHz\n", port->gameport.speed);
 
 	list_add(&port->node, &ns558_list);
+	return;
+out:
+	release_region(io & (-1 << i), (1 << i));
 }
 
 #ifdef CONFIG_PNP

drivers/input/joystick/amijoy.c

@@ -32,6 +32,7 @@
 #include <linux/errno.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/moduleparam.h>
 #include <linux/init.h>
 #include <linux/input.h>
 #include <linux/interrupt.h>
@@ -42,10 +43,15 @@
 
 MODULE_AUTHOR("Vojtech Pavlik <vojtech@ucw.cz>");
 MODULE_DESCRIPTION("Driver for Amiga joysticks");
-MODULE_PARM(amijoy, "1-2i");
 MODULE_LICENSE("GPL");
 
 static int amijoy[2] = { 0, 1 };
+static int amijoy_nargs;  
+module_param_array_named(map, amijoy, uint, amijoy_nargs, 0);
+MODULE_PARM_DESC(map, "Map of attached joysticks in form of <a>,<b> (default is 0,1)");
+
+__obsolete_setup("amijoy=");
+
 static int amijoy_used[2] = { 0, 0 };
 static struct input_dev amijoy_dev[2];
 static char *amijoy_phys[2] = { "amijoy/input0", "amijoy/input1" };
@@ -101,17 +107,6 @@ static void amijoy_close(struct input_dev *dev)
 		free_irq(IRQ_AMIGA_VERTB, amijoy_interrupt);
 }
 
-static int __init amijoy_setup(char *str)
-{
-	int i;
-	int ints[4];
-
-	str = get_options(str, ARRAY_SIZE(ints), ints);
-	for (i = 0; i <= ints[0] && i < 2; i++) amijoy[i] = ints[i+1];
-	return 1;
-}
-__setup("amijoy=", amijoy_setup);
-
 static int __init amijoy_init(void)
 {
 	int i, j;

drivers/input/joystick/analog.c

@@ -32,6 +32,7 @@
 #include <linux/delay.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/moduleparam.h>
 #include <linux/slab.h>
 #include <linux/bitops.h>
 #include <linux/init.h>
@@ -50,9 +51,12 @@ MODULE_LICENSE("GPL");
 #define ANALOG_PORTS		16
 
 static char *js[ANALOG_PORTS];
+static int js_nargs;
 static int analog_options[ANALOG_PORTS];
-MODULE_PARM(js, "1-" __MODULE_STRING(ANALOG_PORTS) "s");
-MODULE_PARM_DESC(js, "Analog joystick options");
+module_param_array_named(map, js, charp, js_nargs, 0);
+MODULE_PARM_DESC(map, "Describes analog joysticks type/capabilities");
+
+__obsolete_setup("js=");
 
 /*
  * Times, feature definitions.
@@ -711,7 +715,7 @@ static void analog_parse_options(void)
 	int i, j;
 	char *end;
 
-	for (i = 0; i < ANALOG_PORTS && js[i]; i++) {
+	for (i = 0; i < js_nargs; i++) {
 
 		for (j = 0; analog_types[j].name; j++)
 			if (!strcmp(analog_types[j].name, js[i])) {
@@ -742,24 +746,6 @@ static struct gameport_dev analog_dev = {
 	.disconnect =	analog_disconnect,
 };
 
-#ifndef MODULE
-static int __init analog_setup(char *str)
-{
-	char *s = str;
-	int i = 0;
-
-	if (!str || !*str) return 0;
-
-	while ((str = s) && (i < ANALOG_PORTS)) {
-		if ((s = strchr(str,','))) *s++ = 0;
-		js[i++] = str;
-	}
-
-	return 1;
-}
-__setup("js=", analog_setup);
-#endif
-
 int __init analog_init(void)
 {
 	analog_parse_options();

drivers/input/joystick/db9.c

@@ -33,6 +33,7 @@
 
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/moduleparam.h>
 #include <linux/delay.h>
 #include <linux/init.h>
 #include <linux/parport.h>
@@ -42,9 +43,24 @@ MODULE_AUTHOR("Vojtech Pavlik <vojtech@ucw.cz>");
 MODULE_DESCRIPTION("Atari, Amstrad, Commodore, Amiga, Sega, etc. joystick driver");
 MODULE_LICENSE("GPL");
 
-MODULE_PARM(db9, "2i");
-MODULE_PARM(db9_2, "2i");
-MODULE_PARM(db9_3, "2i");
+static int db9[] __initdata = { -1, 0 };
+static int db9_nargs __initdata = 0;
+module_param_array_named(dev, db9, int, db9_nargs, 0);
+MODULE_PARM_DESC(dev, "Describes first attached device (<parport#>,<type>)");
+
+static int db9_2[] __initdata = { -1, 0 };
+static int db9_nargs_2 __initdata = 0;
+module_param_array_named(dev2, db9_2, int, db9_nargs_2, 0);
+MODULE_PARM_DESC(dev2, "Describes second attached device (<parport#>,<type>)");
+
+static int db9_3[] __initdata = { -1, 0 };
+static int db9_nargs_3 __initdata = 0;
+module_param_array_named(dev3, db9_3, int, db9_nargs_3, 0);
+MODULE_PARM_DESC(dev3, "Describes third attached device (<parport#>,<type>)");
+
+__obsolete_setup("db9=");
+__obsolete_setup("db9_2=");
+__obsolete_setup("db9_3=");
 
 #define DB9_MULTI_STICK		0x01
 #define DB9_MULTI2_STICK	0x02
@@ -76,10 +92,6 @@ MODULE_PARM(db9_3, "2i");
 #define DB9_GENESIS6_DELAY	14
 #define DB9_REFRESH_TIME	HZ/100
 
-static int db9[] __initdata = { -1, 0 };
-static int db9_2[] __initdata = { -1, 0 };
-static int db9_3[] __initdata = { -1, 0 };
-
 struct db9 {
 	struct input_dev dev[DB9_MAX_DEVICES];
 	struct timer_list timer;
@@ -518,7 +530,7 @@ static void db9_close(struct input_dev *dev)
 	}
 }
 
-static struct db9 __init *db9_probe(int *config)
+static struct db9 __init *db9_probe(int *config, int nargs)
 {
 	struct db9 *db9;
 	struct parport *pp;
@@ -526,6 +538,12 @@ static struct db9 __init *db9_probe(int *config)
 
 	if (config[0] < 0)
 		return NULL;
+
+	if (nargs < 2) {
+		printk(KERN_ERR "db9.c: Device type must be specified.\n");
+		return NULL;
+	}
+
 	if (config[1] < 1 || config[1] >= DB9_MAX_PAD || !db9_buttons[config[1]]) {
 		printk(KERN_ERR "db9.c: bad config\n");
 		return NULL;
@@ -601,38 +619,11 @@ static struct db9 __init *db9_probe(int *config)
 	return db9;
 }
 
-#ifndef MODULE
-static int __init db9_setup(char *str)
-{
-	int i, ints[3];
-	get_options(str, ARRAY_SIZE(ints), ints);
-	for (i = 0; i <= ints[0] && i < 2; i++) db9[i] = ints[i + 1];
-	return 1;
-}
-static int __init db9_setup_2(char *str)
-{
-	int i, ints[3];
-	get_options(str, ARRAY_SIZE(ints), ints);
-	for (i = 0; i <= ints[0] && i < 2; i++) db9_2[i] = ints[i + 1];
-	return 1;
-}
-static int __init db9_setup_3(char *str)
-{
-	int i, ints[3];
-	get_options(str, ARRAY_SIZE(ints), ints);
-	for (i = 0; i <= ints[0] && i < 2; i++) db9_3[i] = ints[i + 1];
-	return 1;
-}
-__setup("db9=", db9_setup);
-__setup("db9_2=", db9_setup_2);
-__setup("db9_3=", db9_setup_3);
-#endif
-
 int __init db9_init(void)
 {
-	db9_base[0] = db9_probe(db9);
-	db9_base[1] = db9_probe(db9_2);
-	db9_base[2] = db9_probe(db9_3);
+	db9_base[0] = db9_probe(db9, db9_nargs);
+	db9_base[1] = db9_probe(db9_2, db9_nargs_2);
+	db9_base[2] = db9_probe(db9_3, db9_nargs_3);
 
 	if (db9_base[0] || db9_base[1] || db9_base[2])
 		return 0;

drivers/input/joystick/gamecon.c

@@ -35,6 +35,7 @@
 #include <linux/kernel.h>
 #include <linux/delay.h>
 #include <linux/module.h>
+#include <linux/moduleparam.h>
 #include <linux/init.h>
 #include <linux/parport.h>
 #include <linux/input.h>
@@ -43,10 +44,26 @@ MODULE_AUTHOR("Vojtech Pavlik <vojtech@ucw.cz>");
 MODULE_DESCRIPTION("NES, SNES, N64, MultiSystem, PSX gamepad driver");
 MODULE_LICENSE("GPL");
 
-MODULE_PARM(gc, "2-6i");
-MODULE_PARM(gc_2,"2-6i");
-MODULE_PARM(gc_3,"2-6i");
-MODULE_PARM(gc_psx_delay, "i");
+static int gc[] __initdata = { -1, 0, 0, 0, 0, 0 };
+static int gc_nargs __initdata = 0;
+module_param_array_named(map, gc, int, gc_nargs, 0);
+MODULE_PARM_DESC(map, "Describers first set of devices (<parport#>,<pad1>,<pad2>,..<pad5>)");
+
+static int gc_2[] __initdata = { -1, 0, 0, 0, 0, 0 };
+static int gc_nargs_2 __initdata = 0;
+module_param_array_named(map2, gc_2, int, gc_nargs_2, 0);
+MODULE_PARM_DESC(map2, "Describers second set of devices");
+
+static int gc_3[] __initdata = { -1, 0, 0, 0, 0, 0 };
+static int gc_nargs_3 __initdata = 0;
+module_param_array_named(map3, gc_3, int, gc_nargs_3, 0);
+MODULE_PARM_DESC(map3, "Describers third set of devices");
+
+__obsolete_setup("gc=");
+__obsolete_setup("gc_2=");
+__obsolete_setup("gc_3=");
+
+/* see also gs_psx_delay parameter in PSX support section */
 
 #define GC_SNES		1
 #define GC_NES		2
@@ -71,10 +88,6 @@ struct gc {
 
 static struct gc *gc_base[3];
 
-static int gc[] __initdata = { -1, 0, 0, 0, 0, 0 };
-static int gc_2[] __initdata = { -1, 0, 0, 0, 0, 0 };
-static int gc_3[] __initdata = { -1, 0, 0, 0, 0, 0 };
-
 static int gc_status_bit[] = { 0x40, 0x80, 0x20, 0x10, 0x08 };
 
 static char *gc_names[] = { NULL, "SNES pad", "NES pad", "NES FourPort", "Multisystem joystick",
@@ -232,6 +245,11 @@ static void gc_multi_read_packet(struct gc *gc, int length, unsigned char *data)
 #define GC_PSX_LEN(x)	((x) & 0xf)	/* Low nibble is length in words */
 
 static int gc_psx_delay = GC_PSX_DELAY;
+module_param_named(psx_delay, gc_psx_delay, uint, 0);
+MODULE_PARM_DESC(psx_delay, "Delay when accessing Sony PSX controller (usecs)");
+
+__obsolete_setup("gc_psx_delay=");
+
 static short gc_psx_abs[] = { ABS_X, ABS_Y, ABS_RX, ABS_RY, ABS_HAT0X, ABS_HAT0Y };
 static short gc_psx_btn[] = { BTN_TL, BTN_TR, BTN_TL2, BTN_TR2, BTN_A, BTN_B, BTN_X, BTN_Y,
 				BTN_START, BTN_SELECT, BTN_THUMBL, BTN_THUMBR };
@@ -468,7 +486,7 @@ static void gc_close(struct input_dev *dev)
 	}
 }
 
-static struct gc __init *gc_probe(int *config)
+static struct gc __init *gc_probe(int *config, int nargs)
 {
 	struct gc *gc;
 	struct parport *pp;
@@ -478,6 +496,11 @@ static struct gc __init *gc_probe(int *config)
 	if (config[0] < 0)
 		return NULL;
 
+	if (nargs < 2) {
+		printk(KERN_ERR "gamecon.c: at least one device must be specified\n");
+		return NULL;
+	}
+
 	pp = parport_find_number(config[0]);
 
 	if (!pp) {
@@ -507,7 +530,7 @@ static struct gc __init *gc_probe(int *config)
 	gc->timer.data = (long) gc;
 	gc->timer.function = gc_timer;
 
-	for (i = 0; i < 5; i++) {
+	for (i = 0; i < nargs - 1; i++) {
 
 		if (!config[i + 1])
 			continue;
@@ -632,44 +655,11 @@ static struct gc __init *gc_probe(int *config)
 	return gc;
 }
 
-#ifndef MODULE
-static int __init gc_setup(char *str)
-{
-	int i, ints[7];
-	get_options(str, ARRAY_SIZE(ints), ints);
-	for (i = 0; i <= ints[0] && i < 6; i++) gc[i] = ints[i + 1];
-	return 1;
-}
-static int __init gc_setup_2(char *str)
-{
-	int i, ints[7];
-	get_options(str, ARRAY_SIZE(ints), ints);
-	for (i = 0; i <= ints[0] && i < 6; i++) gc_2[i] = ints[i + 1];
-	return 1;
-}
-static int __init gc_setup_3(char *str)
-{
-	int i, ints[7];
-	get_options(str, ARRAY_SIZE(ints), ints);
-	for (i = 0; i <= ints[0] && i < 6; i++) gc_3[i] = ints[i + 1];
-	return 1;
-}
-static int __init gc_psx_setup(char *str)
-{
-        get_option(&str, &gc_psx_delay);
-        return 1;
-}
-__setup("gc=", gc_setup);
-__setup("gc_2=", gc_setup_2);
-__setup("gc_3=", gc_setup_3);
-__setup("gc_psx_delay=", gc_psx_setup);
-#endif
-
 int __init gc_init(void)
 {
-	gc_base[0] = gc_probe(gc);
-	gc_base[1] = gc_probe(gc_2);
-	gc_base[2] = gc_probe(gc_3);
+	gc_base[0] = gc_probe(gc, gc_nargs);
+	gc_base[1] = gc_probe(gc_2, gc_nargs_2);
+	gc_base[2] = gc_probe(gc_3, gc_nargs_3);
 
 	if (gc_base[0] || gc_base[1] || gc_base[2])
 		return 0;

drivers/input/joystick/turbografx.c

@@ -35,15 +35,31 @@
 #include <linux/parport.h>
 #include <linux/input.h>
 #include <linux/module.h>
+#include <linux/moduleparam.h>
 #include <linux/init.h>
 
 MODULE_AUTHOR("Vojtech Pavlik <vojtech@ucw.cz>");
 MODULE_DESCRIPTION("TurboGraFX parallel port interface driver");
 MODULE_LICENSE("GPL");
 
-MODULE_PARM(tgfx, "2-8i");
-MODULE_PARM(tgfx_2, "2-8i");
-MODULE_PARM(tgfx_3, "2-8i");
+static int tgfx[] __initdata = { -1, 0, 0, 0, 0, 0, 0, 0 };
+static int tgfx_nargs __initdata = 0;
+module_param_array_named(map, tgfx, int, tgfx_nargs, 0);
+MODULE_PARM_DESC(map, "Describes first set of devices (<parport#>,<js1>,<js2>,..<js7>");
+
+static int tgfx_2[] __initdata = { -1, 0, 0, 0, 0, 0, 0, 0 };
+static int tgfx_nargs_2 __initdata = 0;
+module_param_array_named(map2, tgfx_2, int, tgfx_nargs_2, 0);
+MODULE_PARM_DESC(map2, "Describes second set of devices");
+
+static int tgfx_3[] __initdata = { -1, 0, 0, 0, 0, 0, 0, 0 };
+static int tgfx_nargs_3 __initdata = 0;
+module_param_array_named(map3, tgfx_3, int, tgfx_nargs_3, 0);
+MODULE_PARM_DESC(map3, "Describes third set of devices");
+
+__obsolete_setup("tgfx=");
+__obsolete_setup("tgfx_2=");
+__obsolete_setup("tgfx_3=");
 
 #define TGFX_REFRESH_TIME	HZ/100	/* 10 ms */
 
@@ -58,10 +74,6 @@ MODULE_PARM(tgfx_3, "2-8i");
 #define TGFX_TOP		0x01
 #define TGFX_TOP2		0x08
 
-static int tgfx[] __initdata = { -1, 0, 0, 0, 0, 0, 0, 0 };
-static int tgfx_2[] __initdata = { -1, 0, 0, 0, 0, 0, 0, 0 };
-static int tgfx_3[] __initdata = { -1, 0, 0, 0, 0, 0, 0, 0 };
-
 static int tgfx_buttons[] = { BTN_TRIGGER, BTN_THUMB, BTN_THUMB2, BTN_TOP, BTN_TOP2 };
 static char *tgfx_name = "TurboGraFX Multisystem joystick";
 
@@ -133,7 +145,7 @@ static void tgfx_close(struct input_dev *dev)
  * tgfx_probe() probes for tg gamepads.
  */
 
-static struct tgfx __init *tgfx_probe(int *config)
+static struct tgfx __init *tgfx_probe(int *config, int nargs)
 {
 	struct tgfx *tgfx;
 	struct parport *pp;
@@ -142,6 +154,11 @@ static struct tgfx __init *tgfx_probe(int *config)
 	if (config[0] < 0)
 		return NULL;
 
+	if (nargs < 2) {
+		printk(KERN_ERR "turbografx.c: at least one joystick must be specified\n");
+		return NULL;
+	}
+
 	pp = parport_find_number(config[0]);
 
 	if (!pp) {
@@ -171,7 +188,7 @@ static struct tgfx __init *tgfx_probe(int *config)
 
 	tgfx->sticks = 0;
 
-	for (i = 0; i < 7; i++)
+	for (i = 0; i < nargs - 1; i++)
 		if (config[i+1] > 0 && config[i+1] < 6) {
 
 			tgfx->sticks |= (1 << i);
@@ -212,38 +229,11 @@ static struct tgfx __init *tgfx_probe(int *config)
 	return tgfx;
 }
 
-#ifndef MODULE
-static int __init tgfx_setup(char *str)
-{
-	int i, ints[9];
-	get_options(str, ARRAY_SIZE(ints), ints);
-	for (i = 0; i <= ints[0] && i < 8; i++) tgfx[i] = ints[i + 1];
-	return 1;
-}
-static int __init tgfx_setup_2(char *str)
-{
-	int i, ints[9];
-	get_options(str, ARRAY_SIZE(ints), ints);
-	for (i = 0; i <= ints[0] && i < 8; i++) tgfx_2[i] = ints[i + 1];
-	return 1;
-}
-static int __init tgfx_setup_3(char *str)
-{
-	int i, ints[9];
-	get_options(str, ARRAY_SIZE(ints), ints);
-	for (i = 0; i <= ints[0] && i < 8; i++) tgfx_3[i] = ints[i + 1];
-	return 1;
-}
-__setup("tgfx=", tgfx_setup);
-__setup("tgfx_2=", tgfx_setup_2);
-__setup("tgfx_3=", tgfx_setup_3);
-#endif
-
 int __init tgfx_init(void)
 {
-	tgfx_base[0] = tgfx_probe(tgfx);
-	tgfx_base[1] = tgfx_probe(tgfx_2);
-	tgfx_base[2] = tgfx_probe(tgfx_3);
+	tgfx_base[0] = tgfx_probe(tgfx, tgfx_nargs);
+	tgfx_base[1] = tgfx_probe(tgfx_2, tgfx_nargs_2);
+	tgfx_base[2] = tgfx_probe(tgfx_3, tgfx_nargs_3);
 
 	if (tgfx_base[0] || tgfx_base[1] || tgfx_base[2])
 		return 0;

drivers/input/keyboard/Kconfig

@@ -17,6 +17,7 @@ config KEYBOARD_ATKBD
 	depends on INPUT && INPUT_KEYBOARD
 	select SERIO
 	select SERIO_I8042 if PC
+	select SERIO_GSCPS2 if GSC
 	help
 	  Say Y here if you want to use a standard AT or PS/2 keyboard. Usually
 	  you'll need this, unless you have a different type keyboard (USB, ADB
@@ -40,6 +41,19 @@ config KEYBOARD_SUNKBD
 	  To compile this driver as a module, choose M here: the
 	  module will be called sunkbd.
 
+config KEYBOARD_LKKBD
+	tristate "DECstation/VAXstation LK201/LK401 keyboard support"
+	depends on INPUT && INPUT_KEYBOARD
+	select SERIO
+	help
+	  Say Y here if you want to use a LK201 or LK401 style serial
+	  keyboard. This keyboard is also useable on PCs if you attach
+	  it with the inputattach program. The connector pinout is
+	  described within lkkbd.c.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called lkkbd.
+
 config KEYBOARD_XTKBD
 	tristate "XT Keyboard support"
 	depends on INPUT && INPUT_KEYBOARD

drivers/input/keyboard/Makefile

@@ -7,6 +7,7 @@
 obj-$(CONFIG_KEYBOARD_ATKBD)		+= atkbd.o
 obj-$(CONFIG_KEYBOARD_MAPLE)		+= maple_keyb.o
 obj-$(CONFIG_KEYBOARD_SUNKBD)		+= sunkbd.o
+obj-$(CONFIG_KEYBOARD_LKKBD)		+= lkkbd.o
 obj-$(CONFIG_KEYBOARD_XTKBD)		+= xtkbd.o
 obj-$(CONFIG_KEYBOARD_AMIGA)		+= amikbd.o
 obj-$(CONFIG_KEYBOARD_NEWTON)		+= newtonkbd.o

drivers/input/keyboard/sunkbd.c

@@ -77,6 +77,7 @@ struct sunkbd {
 	struct input_dev dev;
 	struct serio *serio;
 	struct work_struct tq;
+	wait_queue_head_t wait;
 	char name[64];
 	char phys[32];
 	char type;
@@ -96,11 +97,13 @@ static irqreturn_t sunkbd_interrupt(struct serio *serio,
 
 	if (sunkbd->reset <= -1) {		/* If cp[i] is 0xff, sunkbd->reset will stay -1. */
 		sunkbd->reset = data;		/* The keyboard sends 0xff 0xff 0xID on powerup */
+		wake_up_interruptible(&sunkbd->wait);
 		goto out;
 	}
 
 	if (sunkbd->layout == -1) {
 		sunkbd->layout = data;
+		wake_up_interruptible(&sunkbd->wait);
 		goto out;
 	}
 
@@ -176,22 +179,19 @@ static int sunkbd_event(struct input_dev *dev, unsigned int type, unsigned int c
 
 static int sunkbd_initialize(struct sunkbd *sunkbd)
 {
-	int t;
-
-	t = 1000;
 	sunkbd->reset = -2;
 	sunkbd->serio->write(sunkbd->serio, SUNKBD_CMD_RESET);
-	while (sunkbd->reset < 0 && --t) mdelay(1);
-	if (!t) return -1;
+	wait_event_interruptible_timeout(sunkbd->wait, sunkbd->reset >= 0, HZ);
+	if (sunkbd->reset <0)
+		return -1;
 
 	sunkbd->type = sunkbd->reset;
 
 	if (sunkbd->type == 4) {	/* Type 4 keyboard */
-		t = 250;
 		sunkbd->layout = -2;
 		sunkbd->serio->write(sunkbd->serio, SUNKBD_CMD_LAYOUT);
-		while (sunkbd->layout < 0 && --t) mdelay(1);
-		if (!t) return -1;
+		wait_event_interruptible_timeout(sunkbd->wait, sunkbd->layout >= 0, HZ/4);
+		if (sunkbd->layout < 0) return -1;
 		if (sunkbd->layout & SUNKBD_LAYOUT_5_MASK) sunkbd->type = 5;
 	}
 
@@ -206,9 +206,8 @@ static int sunkbd_initialize(struct sunkbd *sunkbd)
 static void sunkbd_reinit(void *data)
 {
 	struct sunkbd *sunkbd = data;
-	int t = 1000;
 
-	while (sunkbd->reset < 0 && --t) mdelay(1);
+	wait_event_interruptible_timeout(sunkbd->wait, sunkbd->reset >= 0, HZ);
 
 	sunkbd->serio->write(sunkbd->serio, SUNKBD_CMD_SETLED);
 	sunkbd->serio->write(sunkbd->serio, 
@@ -239,6 +238,7 @@ static void sunkbd_connect(struct serio *serio, struct serio_dev *dev)
 	memset(sunkbd, 0, sizeof(struct sunkbd));
 
 	init_input_dev(&sunkbd->dev);
+	init_waitqueue_head(&sunkbd->wait);
 
 	sunkbd->dev.evbit[0] = BIT(EV_KEY) | BIT(EV_LED) | BIT(EV_SND) | BIT(EV_REP);
 	sunkbd->dev.ledbit[0] = BIT(LED_CAPSL) | BIT(LED_COMPOSE) | BIT(LED_SCROLLL) | BIT(LED_NUML);
@@ -275,7 +275,7 @@ static void sunkbd_connect(struct serio *serio, struct serio_dev *dev)
 		set_bit(sunkbd->keycode[i], sunkbd->dev.keybit);
 	clear_bit(0, sunkbd->dev.keybit);
 
-	sprintf(sunkbd->name, "%s/input", serio->phys);
+	sprintf(sunkbd->phys, "%s/input0", serio->phys);
 
 	sunkbd->dev.name = sunkbd->name;
 	sunkbd->dev.phys = sunkbd->phys;

drivers/input/misc/Kconfig

@@ -54,12 +54,3 @@ config INPUT_UINPUT
 	  To compile this driver as a module, choose M here: the
 	  module will be called uinput.
 
-config INPUT_GSC
-	tristate "PA-RISC GSC PS/2 keyboard/mouse support"
-	depends on GSC && INPUT && INPUT_MISC
-	help
-	  Say Y here if you have a PS/2 keyboard and/or mouse attached
-	  to your PA-RISC box.	HP run the keyboard in AT mode rather than
-	  XT mode like everyone else, so we need our own driver.
-	  Furthermore, the GSC PS/2 controller shares IRQ between mouse and
-	  keyboard.

drivers/input/misc/Makefile

@@ -9,4 +9,3 @@ obj-$(CONFIG_INPUT_PCSPKR)		+= pcspkr.o
 obj-$(CONFIG_INPUT_M68K_BEEP)		+= m68kspkr.o
 obj-$(CONFIG_INPUT_98SPKR)		+= 98spkr.o
 obj-$(CONFIG_INPUT_UINPUT)		+= uinput.o
-obj-$(CONFIG_INPUT_GSC)			+= gsc_ps2.o

drivers/input/mouse/98busmouse.c

@@ -74,6 +74,8 @@ static int pc98bm_irq = PC98BM_IRQ;
 module_param_named(irq, pc98bm_irq, uint, 0);
 MODULE_PARM_DESC(irq, "IRQ number (13=default)");
 
+__obsolete_setup("pc98bm_irq=");
+
 static int pc98bm_used = 0;
 
 static irqreturn_t pc98bm_interrupt(int irq, void *dev_id, struct pt_regs *regs);

drivers/input/mouse/Kconfig

@@ -17,6 +17,7 @@ config MOUSE_PS2
 	depends on INPUT && INPUT_MOUSE
 	select SERIO
 	select SERIO_I8042 if PC
+	select SERIO_GSCPS2 if GSC
 	---help---
 	  Say Y here if you have a PS/2 mouse connected to your system. This
 	  includes the standard 2 or 3-button PS/2 mouse, as well as PS/2
@@ -117,6 +118,19 @@ config MOUSE_RISCPC
 	  To compile this driver as a module, choose M here: the
 	  module will be called rpcmouse.
 
+config MOUSE_VSXXXAA
+	tristate "DEC VSXXX-AA/GA mouse and tablet"
+	depends on INPUT && INPUT_MOUSE
+	select SERIO
+	help
+	  Say Y (or M) if you want to use a DEC VSXXX-AA (hockey
+	  puck) or a VSXXX-GA (rectangular) mouse. Theses mice are
+	  typically used on DECstations or VAXstations, but can also
+	  be used on any box capable of RS232 (with some adaptor
+	  described in the source file). This driver should, in theory,
+	  also work with the digitizer DEC produced, but it isn't tested
+	  with that (I don't have the hardware yet).
+
 config MOUSE_PC9800
 	tristate "NEC PC-9800 busmouse"
 	depends on X86_PC9800 && INPUT && INPUT_MOUSE && ISA

drivers/input/mouse/Makefile

@@ -13,5 +13,6 @@ obj-$(CONFIG_MOUSE_PC110PAD)	+= pc110pad.o
 obj-$(CONFIG_MOUSE_PC9800)	+= 98busmouse.o
 obj-$(CONFIG_MOUSE_PS2)		+= psmouse.o
 obj-$(CONFIG_MOUSE_SERIAL)	+= sermouse.o
+obj-$(CONFIG_MOUSE_VSXXXAA)	+= vsxxxaa.o
 
 psmouse-objs  := psmouse-base.o logips2pp.o synaptics.o

drivers/input/mouse/inport.c

@@ -85,6 +85,8 @@ static int inport_irq = INPORT_IRQ;
 module_param_named(irq, inport_irq, uint, 0);
 MODULE_PARM_DESC(irq, "IRQ number (5=default)");
 
+__obsolete_setup("inport_irq=");
+
 static int inport_used;
 
 static irqreturn_t inport_interrupt(int irq, void *dev_id, struct pt_regs *regs);

drivers/input/mouse/logibm.c

@@ -75,6 +75,8 @@ static int logibm_irq = LOGIBM_IRQ;
 module_param_named(irq, logibm_irq, uint, 0);
 MODULE_PARM_DESC(irq, "IRQ number (5=default)");
 
+__obsolete_setup("logibm_irq=");
+
 static int logibm_used = 0;
 
 static irqreturn_t logibm_interrupt(int irq, void *dev_id, struct pt_regs *regs);

drivers/input/mouse/psmouse-base.c

@@ -47,6 +47,12 @@ unsigned int psmouse_resetafter;
 module_param_named(resetafter, psmouse_resetafter, uint, 0);
 MODULE_PARM_DESC(resetafter, "Reset Synaptics Touchpad after so many bad packets (0 = never).");
 
+__obsolete_setup("psmouse_noext");
+__obsolete_setup("psmouse_resolution=");
+__obsolete_setup("psmouse_smartscroll=");
+__obsolete_setup("psmouse_resetafter=");
+__obsolete_setup("psmouse_rate=");
+
 static char *psmouse_protocols[] = { "None", "PS/2", "PS2++", "PS2T++", "GenPS/2", "ImPS/2", "ImExPS/2", "SynPS/2"};
 
 /*
@@ -163,14 +169,14 @@ static irqreturn_t psmouse_interrupt(struct serio *serio,
 		       psmouse->name, psmouse->phys, psmouse->pktcnt);
 		psmouse->pktcnt = 0;
 	}
-	
+
 	psmouse->last = jiffies;
 	psmouse->packet[psmouse->pktcnt++] = data;
 
 	if (psmouse->packet[0] == PSMOUSE_RET_BAT) {
 		if (psmouse->pktcnt == 1)
 			goto out;
-		
+
 		if (psmouse->pktcnt == 2) {
 			if (psmouse->packet[1] == PSMOUSE_RET_ID) {
 				psmouse->state = PSMOUSE_IGNORE;
@@ -258,7 +264,7 @@ int psmouse_command(struct psmouse *psmouse, unsigned char *param, int command)
 			return (psmouse->cmdcnt = 0) - 1;
 
 	while (psmouse->cmdcnt && timeout--) {
-	
+
 		if (psmouse->cmdcnt == 1 && command == PSMOUSE_CMD_RESET_BAT &&
 				timeout > 100000) /* do not run in a endless loop */
 			timeout = 100000; /* 1 sec */
@@ -442,7 +448,7 @@ static int psmouse_probe(struct psmouse *psmouse)
  */
 
 	if (psmouse_command(psmouse, NULL, PSMOUSE_CMD_RESET_DIS))
-		return -1;
+		printk(KERN_WARNING "psmouse.c: Failed to reset mouse on %s\n", psmouse->serio->phys);
 
 /*
  * And here we try to determine if it has any extensions over the
@@ -497,7 +503,7 @@ static void psmouse_set_rate(struct psmouse *psmouse)
 static void psmouse_initialize(struct psmouse *psmouse)
 {
 	unsigned char param[2];
-	
+
 /*
  * We set the mouse report rate, resolution and scaling.
  */
@@ -571,7 +577,7 @@ static void psmouse_disconnect(struct serio *serio)
 static void psmouse_connect(struct serio *serio, struct serio_dev *dev)
 {
 	struct psmouse *psmouse;
-	
+
 	if ((serio->type & SERIO_TYPE) != SERIO_8042 &&
 	    (serio->type & SERIO_TYPE) != SERIO_PS_PSTHRU)
 		return;
@@ -603,7 +609,7 @@ static void psmouse_connect(struct serio *serio, struct serio_dev *dev)
 		serio->private = NULL;
 		return;
 	}
-	
+
 	sprintf(psmouse->devname, "%s %s %s",
 		psmouse_protocols[psmouse->type], psmouse->vendor, psmouse->name);
 	sprintf(psmouse->phys, "%s/input0",
@@ -617,7 +623,7 @@ static void psmouse_connect(struct serio *serio, struct serio_dev *dev)
 	psmouse->dev.id.version = psmouse->model;
 
 	input_register_device(&psmouse->dev);
-	
+
 	printk(KERN_INFO "input: %s on %s\n", psmouse->devname, serio->phys);
 
 	psmouse_initialize(psmouse);

drivers/input/mouse/synaptics.c

@@ -435,6 +435,8 @@ int synaptics_init(struct psmouse *psmouse)
 		goto init_fail;
 	}
 
+	priv->pkt_type = SYN_MODEL_NEWABS(priv->model_id) ? SYN_NEWABS : SYN_OLDABS;
+
 	if (SYN_CAP_EXTENDED(priv->capabilities) && SYN_CAP_PASS_THROUGH(priv->capabilities))
        		synaptics_pt_create(psmouse);
 
@@ -602,19 +604,42 @@ static void synaptics_process_packet(struct psmouse *psmouse)
 	input_sync(dev);
 }
 
-static int synaptics_validate_byte(struct psmouse *psmouse)
+static int synaptics_validate_byte(unsigned char packet[], int idx, unsigned char pkt_type)
 {
-	static unsigned char newabs_mask[] = { 0xC0, 0x00, 0x00, 0xC0, 0x00 };
-	static unsigned char newabs_rslt[] = { 0x80, 0x00, 0x00, 0xC0, 0x00 };
-	static unsigned char oldabs_mask[] = { 0xC0, 0x60, 0x00, 0xC0, 0x60 };
-	static unsigned char oldabs_rslt[] = { 0xC0, 0x00, 0x00, 0x80, 0x00 };
-	struct synaptics_data *priv = psmouse->private;
-	int idx = psmouse->pktcnt - 1;
+	static unsigned char newabs_mask[]	= { 0xC8, 0x00, 0x00, 0xC8, 0x00 };
+	static unsigned char newabs_rel_mask[]	= { 0xC0, 0x00, 0x00, 0xC0, 0x00 };
+	static unsigned char newabs_rslt[]	= { 0x80, 0x00, 0x00, 0xC0, 0x00 };
+	static unsigned char oldabs_mask[]	= { 0xC0, 0x60, 0x00, 0xC0, 0x60 };
+	static unsigned char oldabs_rslt[]	= { 0xC0, 0x00, 0x00, 0x80, 0x00 };
 
-	if (SYN_MODEL_NEWABS(priv->model_id))
-		return (psmouse->packet[idx] & newabs_mask[idx]) == newabs_rslt[idx];
-	else
-		return (psmouse->packet[idx] & oldabs_mask[idx]) == oldabs_rslt[idx];
+	switch (pkt_type) {
+		case SYN_NEWABS:
+		case SYN_NEWABS_RELAXED:
+			return (packet[idx] & newabs_rel_mask[idx]) == newabs_rslt[idx];
+
+		case SYN_NEWABS_STRICT:
+			return (packet[idx] & newabs_mask[idx]) == newabs_rslt[idx];
+
+		case SYN_OLDABS:
+			return (packet[idx] & oldabs_mask[idx]) == oldabs_rslt[idx];
+
+		default:
+			printk(KERN_ERR "synaptics: unknown packet type %d\n", pkt_type);
+			return 0;
+	}
+}
+
+static unsigned char synaptics_detect_pkt_type(struct psmouse *psmouse)
+{
+	int i;
+
+	for (i = 0; i < 5; i++)
+		if (!synaptics_validate_byte(psmouse->packet, i, SYN_NEWABS_STRICT)) {
+			printk(KERN_INFO "synaptics: using relaxed packet validation\n");
+			return SYN_NEWABS_RELAXED;
+		}
+
+	return SYN_NEWABS_STRICT;
 }
 
 void synaptics_process_byte(struct psmouse *psmouse, struct pt_regs *regs)
@@ -630,13 +655,17 @@ void synaptics_process_byte(struct psmouse *psmouse, struct pt_regs *regs)
 			printk(KERN_NOTICE "Synaptics driver resynced.\n");
 		}
 
+		if (unlikely(priv->pkt_type == SYN_NEWABS))
+			priv->pkt_type = synaptics_detect_pkt_type(psmouse);
+
 		if (psmouse->ptport && psmouse->ptport->serio.dev && synaptics_is_pt_packet(psmouse->packet))
 			synaptics_pass_pt_packet(&psmouse->ptport->serio, psmouse->packet);
 		else
 			synaptics_process_packet(psmouse);
 		psmouse->pktcnt = 0;
 
-	} else if (psmouse->pktcnt && !synaptics_validate_byte(psmouse)) {
+	} else if (psmouse->pktcnt &&
+		   !synaptics_validate_byte(psmouse->packet, psmouse->pktcnt - 1, priv->pkt_type)) {
 		printk(KERN_WARNING "Synaptics driver lost sync at byte %d\n", psmouse->pktcnt);
 		psmouse->pktcnt = 0;
 		if (++priv->out_of_sync == psmouse_resetafter) {

drivers/input/mouse/synaptics.h

@@ -70,6 +70,12 @@ extern int synaptics_init(struct psmouse *psmouse);
 #define SYN_PS_SET_MODE2		0x14
 #define SYN_PS_CLIENT_CMD		0x28
 
+/* synaptics packet types */
+#define SYN_NEWABS			0
+#define SYN_NEWABS_STRICT		1
+#define SYN_NEWABS_RELAXED		2
+#define SYN_OLDABS			3
+
 /*
  * A structure to describe the state of the touchpad hardware (buttons and pad)
  */
@@ -103,6 +109,7 @@ struct synaptics_data {
 	/* Data for normal processing */
 	unsigned int out_of_sync;		/* # of packets out of sync */
 	int old_w;				/* Previous w value */
+	unsigned char pkt_type;			/* packet type - old, new, etc */
 };
 
 #endif /* _SYNAPTICS_H */

drivers/input/serio/Kconfig

@@ -20,6 +20,7 @@ config SERIO_I8042
 	tristate "i8042 PC Keyboard controller" if EMBEDDED || !X86
 	default y
 	select SERIO
+	depends on !PARISC
 	---help---
 	  i8042 is the chip over which the standard AT keyboard and PS/2
 	  mouse are connected to the computer. If you use these devices,
@@ -48,6 +49,7 @@ config SERIO_SERPORT
 config SERIO_CT82C710
 	tristate "ct82c710 Aux port controller"
 	depends on SERIO
+	depends on !PARISC
 	---help---
 	  Say Y here if you have a Texas Instruments TravelMate notebook
 	  equipped with the ct82c710 chip and want to use a mouse connected
@@ -105,6 +107,20 @@ config SERIO_98KBD
 	  To compile this driver as a module, choose M here: the
 	  module will be called 98kbd-io.
 
+config SERIO_GSCPS2
+	tristate "HP GSC PS/2 keyboard and PS/2 mouse controller"
+	depends on GSC && SERIO
+	default y
+	help
+	  This driver provides support for the PS/2 ports on PA-RISC machines
+	  over which HP PS/2 keyboards and PS/2 mice may be connected.
+	  If you use these devices, you'll need to say Y here.
+
+	  It's safe to enable this driver, so if unsure, say Y.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called gscps2.
+
 config SERIO_PCIPS2
 	tristate "PCI PS/2 keyboard and PS/2 mouse controller"
 	depends on PCI && SERIO

drivers/input/serio/Makefile

@@ -14,4 +14,5 @@ obj-$(CONFIG_SERIO_SA1111)	+= sa1111ps2.o
 obj-$(CONFIG_SERIO_AMBAKMI)	+= ambakmi.o
 obj-$(CONFIG_SERIO_Q40KBD)	+= q40kbd.o
 obj-$(CONFIG_SERIO_98KBD)	+= 98kbd-io.o
+obj-$(CONFIG_SERIO_GSCPS2)	+= gscps2.o
 obj-$(CONFIG_SERIO_PCIPS2)	+= pcips2.o

drivers/input/serio/i8042-io.h

@@ -25,6 +25,9 @@
 #elif defined(__ia64__)
 # define I8042_KBD_IRQ isa_irq_to_vector(1)
 # define I8042_AUX_IRQ isa_irq_to_vector(12)
+#elif defined(__arm__)
+/* defined in include/asm-arm/arch-xxx/irqs.h */
+#include <asm/irq.h>
 #else
 # define I8042_KBD_IRQ	1
 # define I8042_AUX_IRQ	12

drivers/input/serio/i8042.c

@@ -52,6 +52,13 @@ static unsigned int i8042_dumbkbd;
 module_param_named(dumbkbd, i8042_dumbkbd, bool, 0);
 MODULE_PARM_DESC(dumbkbd, "Pretend that controller can only read data from keyboard");
 
+__obsolete_setup("i8042_noaux");
+__obsolete_setup("i8042_nomux");
+__obsolete_setup("i8042_unlock");
+__obsolete_setup("i8042_reset");
+__obsolete_setup("i8042_direct");
+__obsolete_setup("i8042_dumbkbd");
+
 #undef DEBUG
 #include "i8042.h"
 
@@ -379,6 +386,8 @@ static irqreturn_t i8042_interrupt(int irq, void *dev_id, struct pt_regs *regs)
 	unsigned int dfl;
 	int ret;
 
+	mod_timer(&i8042_timer, jiffies + I8042_POLL_PERIOD);
+
 	spin_lock_irqsave(&i8042_lock, flags);
 	str = i8042_read_status();
 	if (str & I8042_STR_OBF)
@@ -433,7 +442,6 @@ static irqreturn_t i8042_interrupt(int irq, void *dev_id, struct pt_regs *regs)
 irq_ret:
 	ret = 1;
 out:
-	mod_timer(&i8042_timer, jiffies + I8042_POLL_PERIOD);
 	return IRQ_RETVAL(ret);
 }
 
@@ -522,6 +530,11 @@ static int __init i8042_check_mux(struct i8042_values *values)
 
 	if (i8042_enable_mux_mode(values, &mux_version))
 		return -1;
+	
+	/* Workaround for broken chips which seem to support MUX, but in reality don't. */
+	/* They all report version 12.10 */
+	if (mux_version == 0xCA)
+		return -1;
 
 	printk(KERN_INFO "i8042.c: Detected active multiplexing controller, rev %d.%d.\n",
 		(mux_version >> 4) & 0xf, mux_version & 0xf);
@@ -708,14 +721,6 @@ static int i8042_controller_init(void)
 			printk(KERN_WARNING "i8042.c: Warning: Keylock active.\n");
 	}
 
-/*
- * If the chip is configured into nontranslated mode by the BIOS, don't
- * bother enabling translating and be happy.
- */
-
-	if (~i8042_ctr & I8042_CTR_XLATE)
-		i8042_direct = 1;
-
 /*
  * Set nontranslated mode for the kbd interface if requested by an option.
  * After this the kbd interface becomes a simple serial in/out, like the aux

drivers/input/serio/serio.c

@@ -195,6 +195,9 @@ irqreturn_t serio_interrupt(struct serio *serio,
                 ret = serio->dev->interrupt(serio, data, flags, regs);
 	} else {
 		if (!flags) {
+			if ((serio->type == SERIO_8042 ||
+				serio->type == SERIO_8042_XL) && (data != 0xaa))
+					return ret;
 			serio_rescan(serio);
 			ret = IRQ_HANDLED;
 		}

drivers/usb/input/hid-core.c

@@ -224,6 +224,9 @@ static int hid_add_field(struct hid_parser *parser, unsigned report_type, unsign
 	offset = report->size;
 	report->size += parser->global.report_size * parser->global.report_count;
 
+	if (usages < parser->global.report_count)
+		usages = parser->global.report_count;
+
 	if (usages == 0)
 		return 0; /* ignore padding fields */
 
@@ -235,9 +238,13 @@ static int hid_add_field(struct hid_parser *parser, unsigned report_type, unsign
 	field->application = hid_lookup_collection(parser, HID_COLLECTION_APPLICATION);
 
 	for (i = 0; i < usages; i++) {
-		field->usage[i].hid = parser->local.usage[i];
+		int j = i;
+		/* Duplicate the last usage we parsed if we have excess values */
+		if (i >= parser->local.usage_index)
+			j = parser->local.usage_index - 1;
+		field->usage[i].hid = parser->local.usage[j];
 		field->usage[i].collection_index =
-			parser->local.collection_index[i];
+			parser->local.collection_index[j];
 	}
 
 	field->maxusage = usages;
@@ -1317,7 +1324,6 @@ void hid_init_reports(struct hid_device *hid)
 #define USB_VENDOR_ID_KBGEAR            0x084e
 #define USB_DEVICE_ID_KBGEAR_JAMSTUDIO  0x1001
 
-
 #define USB_VENDOR_ID_AIPTEK		0x08ca
 #define USB_DEVICE_ID_AIPTEK_6000	0x0020
 
@@ -1356,17 +1362,43 @@ void hid_init_reports(struct hid_device *hid)
 #define USB_VENDOR_ID_A4TECH		0x09DA
 #define USB_DEVICE_ID_A4TECH_WCP32PU	0x0006
 
+#define USB_VENDOR_ID_CYPRESS		0x04b4
+#define USB_DEVICE_ID_CYPRESS_MOUSE	0x0001
+
 #define USB_VENDOR_ID_BERKSHIRE		0x0c98
 #define USB_DEVICE_ID_BERKSHIRE_PCWD	0x1140
 
 #define USB_VENDOR_ID_ALPS		0x0433
 #define USB_DEVICE_ID_IBM_GAMEPAD	0x1101
 
+#define USB_VENDOR_ID_SAITEK		0x06a3
+#define USB_DEVICE_ID_SAITEK_RUMBLEPAD	0xff17
+
+#define USB_VENDOR_ID_NEC		0x073e
+#define USB_DEVICE_ID_NEC_USB_GAME_PAD	0x0301
+
 struct hid_blacklist {
 	__u16 idVendor;
 	__u16 idProduct;
 	unsigned quirks;
 } hid_blacklist[] = {
+
+	{ USB_VENDOR_ID_AIPTEK, USB_DEVICE_ID_AIPTEK_6000, HID_QUIRK_IGNORE },
+	{ USB_VENDOR_ID_BERKSHIRE, USB_DEVICE_ID_BERKSHIRE_PCWD, HID_QUIRK_IGNORE },
+	{ USB_VENDOR_ID_ESSENTIAL_REALITY, USB_DEVICE_ID_ESSENTIAL_REALITY_P5, HID_QUIRK_IGNORE },
+	{ USB_VENDOR_ID_KBGEAR, USB_DEVICE_ID_KBGEAR_JAMSTUDIO, HID_QUIRK_IGNORE },
+	{ USB_VENDOR_ID_GRIFFIN, USB_DEVICE_ID_POWERMATE, HID_QUIRK_IGNORE },
+	{ USB_VENDOR_ID_GRIFFIN, USB_DEVICE_ID_SOUNDKNOB, HID_QUIRK_IGNORE },
+	{ USB_VENDOR_ID_MGE, USB_DEVICE_ID_MGE_UPS, HID_QUIRK_IGNORE },
+	{ USB_VENDOR_ID_MGE, USB_DEVICE_ID_MGE_UPS1, HID_QUIRK_IGNORE },
+
+	{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100, HID_QUIRK_IGNORE },
+	{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 100, HID_QUIRK_IGNORE },
+	{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 200, HID_QUIRK_IGNORE },
+	{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 300, HID_QUIRK_IGNORE },
+	{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 400, HID_QUIRK_IGNORE },
+	{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 500, HID_QUIRK_IGNORE },
+
 	{ USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_PENPARTNER, HID_QUIRK_IGNORE },
 	{ USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_GRAPHIRE, HID_QUIRK_IGNORE },
 	{ USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_GRAPHIRE + 1, HID_QUIRK_IGNORE },
@@ -1388,32 +1420,25 @@ struct hid_blacklist {
 	{ USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_INTUOS2 + 2, HID_QUIRK_IGNORE },
 	{ USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_INTUOS2 + 3, HID_QUIRK_IGNORE },
 	{ USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_INTUOS2 + 4, HID_QUIRK_IGNORE },
-	{ USB_VENDOR_ID_KBGEAR, USB_DEVICE_ID_KBGEAR_JAMSTUDIO, HID_QUIRK_IGNORE },
-	{ USB_VENDOR_ID_AIPTEK, USB_DEVICE_ID_AIPTEK_6000, HID_QUIRK_IGNORE },
-	{ USB_VENDOR_ID_GRIFFIN, USB_DEVICE_ID_POWERMATE, HID_QUIRK_IGNORE },
-	{ USB_VENDOR_ID_GRIFFIN, USB_DEVICE_ID_SOUNDKNOB, HID_QUIRK_IGNORE },
+
 	{ USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_UC100KM, HID_QUIRK_NOGET },
 	{ USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_CS124U, HID_QUIRK_NOGET },
 	{ USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_2PORTKVM, HID_QUIRK_NOGET },
 	{ USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_4PORTKVM, HID_QUIRK_NOGET },
 	{ USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_4PORTKVMC, HID_QUIRK_NOGET },
-	{ USB_VENDOR_ID_MGE, USB_DEVICE_ID_MGE_UPS, HID_QUIRK_IGNORE },
-	{ USB_VENDOR_ID_MGE, USB_DEVICE_ID_MGE_UPS1, HID_QUIRK_IGNORE },
-	{ USB_VENDOR_ID_TOPMAX, USB_DEVICE_ID_TOPMAX_COBRAPAD, HID_QUIRK_BADPAD },
-	{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_DRIVING, HID_QUIRK_BADPAD|HID_QUIRK_MULTI_INPUT },
-	{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FLYING, HID_QUIRK_BADPAD|HID_QUIRK_MULTI_INPUT },
-	{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FIGHTING, HID_QUIRK_BADPAD|HID_QUIRK_MULTI_INPUT },
-	{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100, HID_QUIRK_IGNORE },
-	{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 100, HID_QUIRK_IGNORE },
-	{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 200, HID_QUIRK_IGNORE },
-	{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 300, HID_QUIRK_IGNORE },
-	{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 400, HID_QUIRK_IGNORE },
-	{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 500, HID_QUIRK_IGNORE },
 	{ USB_VENDOR_ID_TANGTOP, USB_DEVICE_ID_TANGTOP_USBPS2, HID_QUIRK_NOGET },
-	{ USB_VENDOR_ID_ESSENTIAL_REALITY, USB_DEVICE_ID_ESSENTIAL_REALITY_P5, HID_QUIRK_IGNORE },
-	{ USB_VENDOR_ID_A4TECH, USB_DEVICE_ID_A4TECH_WCP32PU, HID_QUIRK_2WHEEL_MOUSE_HACK },
-	{ USB_VENDOR_ID_BERKSHIRE, USB_DEVICE_ID_BERKSHIRE_PCWD, HID_QUIRK_IGNORE },
+
+	{ USB_VENDOR_ID_A4TECH, USB_DEVICE_ID_A4TECH_WCP32PU, HID_QUIRK_2WHEEL_MOUSE_HACK_BACK },
+	{ USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_MOUSE, HID_QUIRK_2WHEEL_MOUSE_HACK_EXTRA },
+
 	{ USB_VENDOR_ID_ALPS, USB_DEVICE_ID_IBM_GAMEPAD, HID_QUIRK_BADPAD },
+	{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_DRIVING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
+	{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FLYING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
+	{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FIGHTING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
+	{ USB_VENDOR_ID_NEC, USB_DEVICE_ID_NEC_USB_GAME_PAD, HID_QUIRK_BADPAD },
+	{ USB_VENDOR_ID_SAITEK, USB_DEVICE_ID_SAITEK_RUMBLEPAD, HID_QUIRK_BADPAD },
+	{ USB_VENDOR_ID_TOPMAX, USB_DEVICE_ID_TOPMAX_COBRAPAD, HID_QUIRK_BADPAD },
+
 	{ 0, 0 }
 };
 

drivers/usb/input/hid-input.c

@@ -377,7 +377,8 @@ static void hidinput_configure_usage(struct hid_input *hidinput, struct hid_fiel
 
 	set_bit(usage->type, input->evbit);
 	if ((usage->type == EV_REL)
-			&& (device->quirks & HID_QUIRK_2WHEEL_MOUSE_HACK)
+			&& (device->quirks & (HID_QUIRK_2WHEEL_MOUSE_HACK_BACK
+				| HID_QUIRK_2WHEEL_MOUSE_HACK_EXTRA))
 			&& (usage->code == REL_WHEEL)) {
 		set_bit(REL_HWHEEL, bit);
 	}
@@ -431,21 +432,22 @@ void hidinput_hid_event(struct hid_device *hid, struct hid_field *field, struct
 
 	input_regs(input, regs);
 
-	if ((hid->quirks & HID_QUIRK_2WHEEL_MOUSE_HACK)
-			&& (usage->code == BTN_BACK)) {
+	if (((hid->quirks & HID_QUIRK_2WHEEL_MOUSE_HACK_EXTRA) && (usage->code == BTN_EXTRA))
+		|| ((hid->quirks & HID_QUIRK_2WHEEL_MOUSE_HACK_BACK) && (usage->code == BTN_BACK))) {
 		if (value)
 			hid->quirks |= HID_QUIRK_2WHEEL_MOUSE_HACK_ON;
 		else
 			hid->quirks &= ~HID_QUIRK_2WHEEL_MOUSE_HACK_ON;
 		return;
 	}
+
 	if ((hid->quirks & HID_QUIRK_2WHEEL_MOUSE_HACK_ON)
 			&& (usage->code == REL_WHEEL)) {
 		input_event(input, usage->type, REL_HWHEEL, value);
 		return;
 	}
 
-	if (usage->hat_min != usage->hat_max) {
+	if (usage->hat_min != usage->hat_max ) { /* FIXME: hat_max can be 0 and hat_min 1 */
 		value = (value - usage->hat_min) * 8 / (usage->hat_max - usage->hat_min + 1) + 1;
 		if (value < 0 || value > 8) value = 0;
 		input_event(input, usage->type, usage->code    , hid_hat_to_axis[value].x);
@@ -484,7 +486,7 @@ void hidinput_hid_event(struct hid_device *hid, struct hid_field *field, struct
 		return;
 	}
 
-	if((usage->type == EV_KEY) && (usage->code == 0)) /* Key 0 is "unassigned", not KEY_UKNOWN */
+	if((usage->type == EV_KEY) && (usage->code == 0)) /* Key 0 is "unassigned", not KEY_UNKNOWN */
 		return;
 
 	input_event(input, usage->type, usage->code, value);

drivers/usb/input/hid.h

@@ -201,15 +201,16 @@ struct hid_item {
  * HID device quirks.
  */
 
-#define HID_QUIRK_INVERT		0x001
-#define HID_QUIRK_NOTOUCH		0x002
-#define HID_QUIRK_IGNORE		0x004
-#define HID_QUIRK_NOGET			0x008
-#define HID_QUIRK_HIDDEV		0x010
-#define HID_QUIRK_BADPAD		0x020
-#define HID_QUIRK_MULTI_INPUT		0x040
-#define HID_QUIRK_2WHEEL_MOUSE_HACK	0x080
-#define HID_QUIRK_2WHEEL_MOUSE_HACK_ON	0x100
+#define HID_QUIRK_INVERT			0x001
+#define HID_QUIRK_NOTOUCH			0x002
+#define HID_QUIRK_IGNORE			0x004
+#define HID_QUIRK_NOGET				0x008
+#define HID_QUIRK_HIDDEV			0x010
+#define HID_QUIRK_BADPAD			0x020
+#define HID_QUIRK_MULTI_INPUT			0x040
+#define HID_QUIRK_2WHEEL_MOUSE_HACK_BACK	0x080
+#define HID_QUIRK_2WHEEL_MOUSE_HACK_EXTRA	0x100
+#define HID_QUIRK_2WHEEL_MOUSE_HACK_ON		0x200
 
 /*
  * This is the global environment of the parser. This information is

drivers/usb/input/hiddev.c

@@ -403,7 +403,8 @@ static int hiddev_ioctl(struct inode *inode, struct file *file, unsigned int cmd
 	struct hiddev_collection_info cinfo;
 	struct hiddev_report_info rinfo;
 	struct hiddev_field_info finfo;
-	struct hiddev_usage_ref uref;
+	struct hiddev_usage_ref_multi uref_multi;
+	struct hiddev_usage_ref *uref = &uref_multi.uref;
 	struct hiddev_devinfo dinfo;
 	struct hid_report *report;
 	struct hid_field *field;
@@ -575,68 +576,98 @@ static int hiddev_ioctl(struct inode *inode, struct file *file, unsigned int cmd
 		return 0;
 
 	case HIDIOCGUCODE:
-		if (copy_from_user(&uref, (void *) arg, sizeof(uref)))
+		if (copy_from_user(uref, (void *) arg, sizeof(*uref)))
 			return -EFAULT;
 
-		rinfo.report_type = uref.report_type;
-		rinfo.report_id = uref.report_id;
+		rinfo.report_type = uref->report_type;
+		rinfo.report_id = uref->report_id;
 		if ((report = hiddev_lookup_report(hid, &rinfo)) == NULL)
 			return -EINVAL;
 
-		if (uref.field_index >= report->maxfield)
+		if (uref->field_index >= report->maxfield)
 			return -EINVAL;
 
-		field = report->field[uref.field_index];
-		if (uref.usage_index >= field->maxusage)
+		field = report->field[uref->field_index];
+		if (uref->usage_index >= field->maxusage)
 			return -EINVAL;
 
-		uref.usage_code = field->usage[uref.usage_index].hid;
+		uref->usage_code = field->usage[uref->usage_index].hid;
 
-		if (copy_to_user((void *) arg, &uref, sizeof(uref)))
+		if (copy_to_user((void *) arg, uref, sizeof(*uref)))
 			return -EFAULT;
 
 		return 0;
 
 	case HIDIOCGUSAGE:
 	case HIDIOCSUSAGE:
+	case HIDIOCGUSAGES:
+	case HIDIOCSUSAGES:
 	case HIDIOCGCOLLECTIONINDEX:
-		if (copy_from_user(&uref, (void *) arg, sizeof(uref)))
-			return -EFAULT;
+		if (cmd == HIDIOCGUSAGES || cmd == HIDIOCSUSAGES) {
+			if (copy_from_user(&uref_multi, (void *) arg, 
+					   sizeof(uref_multi)))
+				return -EFAULT;
+		} else {
+			if (copy_from_user(uref, (void *) arg, sizeof(*uref)))
+				return -EFAULT;
+		}
 
-		if (cmd != HIDIOCGUSAGE && uref.report_type == HID_REPORT_TYPE_INPUT)
-				return -EINVAL;
+		if (cmd != HIDIOCGUSAGE && 
+		    cmd != HIDIOCGUSAGES &&
+		    uref->report_type == HID_REPORT_TYPE_INPUT)
+			return -EINVAL;
 
-		if (uref.report_id == HID_REPORT_ID_UNKNOWN) {
-			field = hiddev_lookup_usage(hid, &uref);
+		if (uref->report_id == HID_REPORT_ID_UNKNOWN) {
+			field = hiddev_lookup_usage(hid, uref);
 			if (field == NULL)
 				return -EINVAL;
 		} else {
-			rinfo.report_type = uref.report_type;
-			rinfo.report_id = uref.report_id;
+			rinfo.report_type = uref->report_type;
+			rinfo.report_id = uref->report_id;
 			if ((report = hiddev_lookup_report(hid, &rinfo)) == NULL)
 				return -EINVAL;
 
-			if (uref.field_index >= report->maxfield)
+			if (uref->field_index >= report->maxfield)
 				return -EINVAL;
 
-			field = report->field[uref.field_index];
-			if (uref.usage_index >= field->maxusage)
+			field = report->field[uref->field_index];
+			if (uref->usage_index >= field->maxusage)
 				return -EINVAL;
+
+			if (cmd == HIDIOCGUSAGES || cmd == HIDIOCSUSAGES) {
+				if (uref_multi.num_values >= HID_MAX_USAGES || 
+				    uref->usage_index >= field->maxusage || 
+				   (uref->usage_index + uref_multi.num_values) >= field->maxusage)
+					return -EINVAL;
+			}
 		}
 
 		switch (cmd) {
 			case HIDIOCGUSAGE:
-				uref.value = field->value[uref.usage_index];
-				if (copy_to_user((void *) arg, &uref, sizeof(uref)))
+				uref->value = field->value[uref->usage_index];
+				if (copy_to_user((void *) arg, uref, sizeof(*uref)))
 					return -EFAULT;
 				return 0;
 
 			case HIDIOCSUSAGE:
-				field->value[uref.usage_index] = uref.value;
+				field->value[uref->usage_index] = uref->value;
 				return 0;
 
 			case HIDIOCGCOLLECTIONINDEX:
-				return field->usage[uref.usage_index].collection_index;
+				return field->usage[uref->usage_index].collection_index;
+			case HIDIOCGUSAGES:
+				for (i = 0; i < uref_multi.num_values; i++)
+					uref_multi.values[i] = 
+					    field->value[uref->usage_index + i];
+				if (copy_to_user((void *) arg, &uref_multi, 
+						 sizeof(uref_multi)))
+					return -EFAULT;
+				return 0;
+			case HIDIOCSUSAGES:
+				for (i = 0; i < uref_multi.num_values; i++)
+					field->value[uref->usage_index + i] = 
+				  	    uref_multi.values[i];
+				return 0;
 		}
 
 		return 0;

drivers/usb/input/wacom.c

 /*
  *  USB Wacom Graphire and Wacom Intuos tablet support
  *
- *  Copyright (c) 2000-2002 Vojtech Pavlik	<vojtech@ucw.cz>
+ *  Copyright (c) 2000-2004 Vojtech Pavlik	<vojtech@ucw.cz>
  *  Copyright (c) 2000 Andreas Bach Aaen	<abach@stofanet.dk>
  *  Copyright (c) 2000 Clifford Wolf		<clifford@clifford.at>
  *  Copyright (c) 2000 Sam Mosel		<sam.mosel@computer.org>
@@ -9,6 +9,7 @@
  *  Copyright (c) 2000 Daniel Egger		<egger@suse.de>
  *  Copyright (c) 2001 Frederic Lepied		<flepied@mandrakesoft.com>
  *  Copyright (c) 2002 Ping Cheng		<pingc@wacom.com>
+ *  Copyright (c) 2004 Panagiotis Issaris	<panagiotis.issaris@mech.kuleuven.ac.be>
  *
  *  ChangeLog:
  *      v0.1 (vp)  - Initial release
@@ -48,6 +49,7 @@
  *	v1.30 (vp) - Merge 2.4 and 2.5 drivers
  *		   - Since 2.5 now has input_sync(), remove MSC_SERIAL abuse
  *		   - Cleanups here and there
+ *    v1.30.1 (pi) - Added Graphire3 support
  */
 
 /*

include/asm-arm/arch-ebsa285/irqs.h

@@ -91,8 +91,8 @@
 
 #undef RTC_IRQ
 #define RTC_IRQ		IRQ_ISA_RTC_ALARM
-#undef AUX_IRQ
-#define AUX_IRQ		(machine_is_netwinder() ? IRQ_NETWINDER_PS2MOUSE : IRQ_ISA_PS2MOUSE)
+#define I8042_KBD_IRQ	IRQ_ISA_KEYBOARD
+#define I8042_AUX_IRQ	(machine_is_netwinder() ? IRQ_NETWINDER_PS2MOUSE : IRQ_ISA_PS2MOUSE)
 #define IRQ_FLOPPYDISK	IRQ_ISA_FLOPPY
 
 #define irq_canonicalize(_i)	(((_i) == IRQ_ISA_CASCADE) ? IRQ_ISA_2 : _i)

include/asm-arm/arch-shark/irqs.h

@@ -8,5 +8,6 @@
 
 #define IRQ_ISA_KEYBOARD	 1
 #define RTC_IRQ			 8
-#define AUX_IRQ			12
+#define I8042_KBD_IRQ		 1
+#define I8042_AUX_IRQ		12
 #define IRQ_HARDDISK            14

include/linux/hiddev.h

@@ -39,33 +39,33 @@ struct hiddev_event {
 };
 
 struct hiddev_devinfo {
-	unsigned int bustype;
-	unsigned int busnum;
-	unsigned int devnum;
-	unsigned int ifnum;
-	short vendor;
-	short product;
-	short version;
-	unsigned num_applications;
+	__u32 bustype;
+	__u32 busnum;
+	__u32 devnum;
+	__u32 ifnum;
+	__s16 vendor;
+	__s16 product;
+	__s16 version;
+	__u32 num_applications;
 };
 
 struct hiddev_collection_info {
-	unsigned index;
-	unsigned type;
-	unsigned usage;
-	unsigned level;
+	__u32 index;
+	__u32 type;
+	__u32 usage;
+	__u32 level;
 };
 
 #define HID_STRING_SIZE 256
 struct hiddev_string_descriptor {
-	int index;
+	__s32 index;
 	char value[HID_STRING_SIZE];
 };
 
 struct hiddev_report_info {
-	unsigned report_type;
-	unsigned report_id;
-	unsigned num_fields;
+	__u32 report_type;
+	__u32 report_id;
+	__u32 num_fields;
 };
 
 /* To do a GUSAGE/SUSAGE, fill in at least usage_code,  report_type and 
@@ -88,20 +88,20 @@ struct hiddev_report_info {
 #define HID_REPORT_TYPE_MAX     3
 
 struct hiddev_field_info {
-	unsigned report_type;
-	unsigned report_id;
-	unsigned field_index;
-	unsigned maxusage;
-	unsigned flags;
-	unsigned physical;		/* physical usage for this field */
-	unsigned logical;		/* logical usage for this field */
-	unsigned application;		/* application usage for this field */
+	__u32 report_type;
+	__u32 report_id;
+	__u32 field_index;
+	__u32 maxusage;
+	__u32 flags;
+	__u32 physical;		/* physical usage for this field */
+	__u32 logical;		/* logical usage for this field */
+	__u32 application;		/* application usage for this field */
 	__s32 logical_minimum;
 	__s32 logical_maximum;
 	__s32 physical_minimum;
 	__s32 physical_maximum;
-	unsigned unit_exponent;
-	unsigned unit;
+	__u32 unit_exponent;
+	__u32 unit;
 };
 
 /* Fill in report_type, report_id and field_index to get the information on a
@@ -118,14 +118,22 @@ struct hiddev_field_info {
 #define HID_FIELD_BUFFERED_BYTE		0x100
 
 struct hiddev_usage_ref {
-	unsigned report_type;
-	unsigned report_id;
-	unsigned field_index;
-	unsigned usage_index;
-	unsigned usage_code;
+	__u32 report_type;
+	__u32 report_id;
+	__u32 field_index;
+	__u32 usage_index;
+	__u32 usage_code;
 	__s32 value;
 };
 
+/* hiddev_usage_ref_multi is used for sending multiple bytes to a control.
+ * It really manifests itself as setting the value of consecutive usages */
+struct hiddev_usage_ref_multi {
+	struct hiddev_usage_ref uref;
+	__u32 num_values;
+	__s32 values[HID_MAX_USAGES];
+};
+
 /* FIELD_INDEX_NONE is returned in read() data from the kernel when flags
  * is set to (HIDDEV_FLAG_UREF | HIDDEV_FLAG_REPORT) and a new report has
  * been sent by the device 
@@ -161,6 +169,10 @@ struct hiddev_usage_ref {
 #define HIDIOCGCOLLECTIONINFO	_IOWR('H', 0x11, struct hiddev_collection_info)
 #define HIDIOCGPHYS(len)	_IOC(_IOC_READ, 'H', 0x12, len)
 
+/* For writing/reading to multiple/consecutive usages */
+#define HIDIOCGUSAGES		_IOWR('H', 0x13, struct hiddev_usage_ref_multi)
+#define HIDIOCSUSAGES		_IOW('H', 0x14, struct hiddev_usage_ref_multi)
+
 /* 
  * Flags to be used in HIDIOCSFLAG
  */

include/linux/init.h

@@ -110,12 +110,21 @@ struct obs_kernel_param {
 };
 
 /* OBSOLETE: see moduleparam.h for the right way. */
-#define __setup(str, fn)					\
-	static char __setup_str_##fn[] __initdata = str;	\
-	static struct obs_kernel_param __setup_##fn		\
+#define __setup_param(str, unique_id, fn)			\
+	static char __setup_str_##unique_id[] __initdata = str;	\
+	static struct obs_kernel_param __setup_##unique_id	\
 		 __attribute_used__				\
 		 __attribute__((__section__(".init.setup")))	\
-		= { __setup_str_##fn, fn }
+		= { __setup_str_##unique_id, fn }
+
+#define __setup_null_param(str, unique_id)			\
+	__setup_param(str, unique_id, NULL)
+
+#define __setup(str, fn)					\
+	__setup_param(str, fn, fn)
+
+#define __obsolete_setup(str)					\
+	__setup_null_param(str, __LINE__)
 
 #endif /* __ASSEMBLY__ */
 
@@ -172,7 +181,10 @@ struct obs_kernel_param {
 	{ return exitfn; }					\
 	void cleanup_module(void) __attribute__((alias(#exitfn)));
 
-#define __setup(str,func) /* nothing */
+#define __setup_param(str, unique_id, fn)	/* nothing */
+#define __setup_null_param(str, unique_id) 	/* nothing */
+#define __setup(str, func) 			/* nothing */
+#define __obsolete_setup(str) 			/* nothing */
 #endif
 
 /* Data marked not to be saved by software_suspend() */

include/linux/miscdevice.h

@@ -3,7 +3,6 @@
 #include <linux/module.h>
 #include <linux/major.h>
 
-#define BUSMOUSE_MINOR 0
 #define PSMOUSE_MINOR  1
 #define MS_BUSMOUSE_MINOR 2
 #define ATIXL_BUSMOUSE_MINOR 3

include/linux/moduleparam.h

@@ -126,13 +126,16 @@ extern int param_get_invbool(char *buffer, struct kernel_param *kp);
 #define param_check_invbool(name, p) __param_check(name, p, int)
 
 /* Comma-separated array: num is set to number they actually specified. */
-#define module_param_array(name, type, num, perm)			\
+#define module_param_array_named(name, array, type, num, perm)		\
 	static struct kparam_array __param_arr_##name			\
-	= { ARRAY_SIZE(name), &num, param_set_##type, param_get_##type,	\
-	    sizeof(name[0]), name };					\
+	= { ARRAY_SIZE(array), &num, param_set_##type, param_get_##type,\
+	    sizeof(array[0]), array };					\
 	module_param_call(name, param_array_set, param_array_get, 	\
 			  &__param_arr_##name, perm)
 
+#define module_param_array(name, type, num, perm)		\
+	module_param_array_named(name, name, type, num, perm)
+
 extern int param_array_set(const char *val, struct kernel_param *kp);
 extern int param_array_get(char *buffer, struct kernel_param *kp);
 

include/linux/serio.h

@@ -117,6 +117,7 @@ static __inline__ void serio_cleanup(struct serio *serio)
 #define SERIO_MZ	0x05
 #define SERIO_MZP	0x06
 #define SERIO_MZPP	0x07
+#define SERIO_VSXXXAA	0x08
 #define SERIO_SUNKBD	0x10
 #define SERIO_WARRIOR	0x18
 #define SERIO_SPACEORB	0x19
@@ -134,6 +135,7 @@ static __inline__ void serio_cleanup(struct serio *serio)
 #define SERIO_HIL	0x25
 #define SERIO_SNES232	0x26
 #define SERIO_SEMTECH	0x27
+#define SERIO_LKKBD	0x28
 
 #define SERIO_ID	0xff00UL
 #define SERIO_EXTRA	0xff0000UL

init/main.c

@@ -155,8 +155,11 @@ static int __init obsolete_checksetup(char *line)
 	p = &__setup_start;
 	do {
 		int n = strlen(p->str);
-		if (!strncmp(line,p->str,n)) {
-			if (p->setup_func(line+n))
+		if (!strncmp(line, p->str, n)) {
+			if (!p->setup_func) {
+				printk(KERN_WARNING "Parameter %s is obsolete, ignored\n", p->str);
+				return 1;
+			} else if (p->setup_func(line + n))
 				return 1;
 		}
 		p++;