[PATCH] Generic HDLC update

The attached patch updates generic HDLC to version 1.18.
FR Cisco LMI production-tested. Please apply to Linux 2.6. Thanks.

Changes:
- doc updates
- added Cisco LMI support to Frame-Relay code
- cleaned hdlc_fr.c a bit, removed some orphaned #defines etc.
- fixed a problem with non-functional LMI in FR DCE mode.
- changed diagnostic messages to better conform to FR standards
- all protocols: information about carrier changes (DCD line) is now
  printed to kernel logs.
Signed-Off-By: Krzysztof Halasa <khc@pm.waw.pl>

Documentation/networking/generic-hdlc.txt

 Generic HDLC layer
 Krzysztof Halasa <khc@pm.waw.pl>
-January, 2003
 
 
 Generic HDLC layer currently supports:
-- Frame Relay (ANSI, CCITT and no LMI), with ARP support (no InARP).
-  Normal (routed) and Ethernet-bridged (Ethernet device emulation)
+1. Frame Relay (ANSI, CCITT, Cisco and no LMI).
+   - Normal (routed) and Ethernet-bridged (Ethernet device emulation)
      interfaces can share a single PVC.
-- raw HDLC - either IP (IPv4) interface or Ethernet device emulation.
-- Cisco HDLC,
-- PPP (uses syncppp.c),
-- X.25 (uses X.25 routines).
+   - ARP support (no InARP support in the kernel - there is an
+     experimental InARP user-space daemon available on:
+     http://www.kernel.org/pub/linux/utils/net/hdlc/).
+2. raw HDLC - either IP (IPv4) interface or Ethernet device emulation.
+3. Cisco HDLC.
+4. PPP (uses syncppp.c).
+5. X.25 (uses X.25 routines).
 
-There are hardware drivers for the following cards:
-- C101 by Moxa Technologies Co., Ltd.
-- RISCom/N2 by SDL Communications Inc.
-- and others, some not in the official kernel.
+Generic HDLC is a protocol driver only - it needs a low-level driver
+for your particular hardware.
 
 Ethernet device emulation (using HDLC or Frame-Relay PVC) is compatible
 with IEEE 802.1Q (VLANs) and 802.1D (Ethernet bridging).
@@ -24,7 +24,7 @@ with IEEE 802.1Q (VLANs) and 802.1D (Ethernet bridging).
 Make sure the hdlc.o and the hardware driver are loaded. It should
 create a number of "hdlc" (hdlc0 etc) network devices, one for each
 WAN port. You'll need the "sethdlc" utility, get it from:
-	http://hq.pm.waw.pl/hdlc/
+	http://www.kernel.org/pub/linux/utils/net/hdlc/
 
 Compile sethdlc.c utility:
 	gcc -O2 -Wall -o sethdlc sethdlc.c
@@ -52,12 +52,12 @@ Setting interface:
 * v35 | rs232 | x21 | t1 | e1 - sets physical interface for a given port
                                 if the card has software-selectable interfaces
   loopback - activate hardware loopback (for testing only)
-* clock ext - external clock (uses DTE RX and TX clock)
-* clock int - internal clock (provides clock signal on DCE clock output)
-* clock txint - TX internal, RX external (provides TX clock on DCE output)
-* clock txfromrx - TX clock derived from RX clock (TX clock on DCE output)
-* rate - sets clock rate in bps (not required for external clock or
-                                 for txfromrx)
+* clock ext - both RX clock and TX clock external
+* clock int - both RX clock and TX clock internal
+* clock txint - RX clock external, TX clock internal
+* clock txfromrx - RX clock external, TX clock derived from RX clock
+* rate - sets clock rate in bps (for "int" or "txint" clock only)
+
 
 Setting protocol:
 
@@ -79,7 +79,7 @@ Setting protocol:
 * x25 - sets X.25 mode
 
 * fr - Frame Relay mode
-  lmi ansi / ccitt / none - LMI (link management) type
+  lmi ansi / ccitt / cisco / none - LMI (link management) type
   dce - Frame Relay DCE (network) side LMI instead of default DTE (user).
   It has nothing to do with clocks!
   t391 - link integrity verification polling timer (in seconds) - user
@@ -119,13 +119,14 @@ or
 
 
 
-If you have a problem with N2 or C101 card, you can issue the "private"
-command to see port's packet descriptor rings (in kernel logs):
+If you have a problem with N2, C101 or PLX200SYN card, you can issue the
+"private" command to see port's packet descriptor rings (in kernel logs):
 
 	sethdlc hdlc0 private
 
-The hardware driver has to be build with CONFIG_HDLC_DEBUG_RINGS.
+The hardware driver has to be build with #define DEBUG_RINGS.
 Attaching this info to bug reports would be helpful. Anyway, let me know
 if you have problems using this.
 
-For patches and other info look at http://hq.pm.waw.pl/hdlc/
+For patches and other info look at:
+<http://www.kernel.org/pub/linux/utils/net/hdlc/>.

drivers/net/wan/hdlc_generic.c

 /*
  * Generic HDLC support routines for Linux
  *
- * Copyright (C) 1999 - 2003 Krzysztof Halasa <khc@pm.waw.pl>
+ * Copyright (C) 1999 - 2005 Krzysztof Halasa <khc@pm.waw.pl>
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of version 2 of the GNU General Public License
@@ -38,7 +38,7 @@
 #include <linux/hdlc.h>
 
 
-static const char* version = "HDLC support module revision 1.17";
+static const char* version = "HDLC support module revision 1.18";
 
 #undef DEBUG_LINK
 
@@ -126,10 +126,13 @@ void hdlc_set_carrier(int on, struct net_device *dev)
 	if (!hdlc->open)
 		goto carrier_exit;
 
-	if (hdlc->carrier)
+	if (hdlc->carrier) {
+		printk(KERN_INFO "%s: Carrier detected\n", dev->name);
 		__hdlc_set_carrier_on(dev);
-	else
+	} else {
+		printk(KERN_INFO "%s: Carrier lost\n", dev->name);
 		__hdlc_set_carrier_off(dev);
+	}
 
 carrier_exit:
 	spin_unlock_irqrestore(&hdlc->state_lock, flags);
@@ -157,8 +160,11 @@ int hdlc_open(struct net_device *dev)
 
 	spin_lock_irq(&hdlc->state_lock);
 
-	if (hdlc->carrier)
+	if (hdlc->carrier) {
+		printk(KERN_INFO "%s: Carrier detected\n", dev->name);
 		__hdlc_set_carrier_on(dev);
+	} else
+		printk(KERN_INFO "%s: No carrier\n", dev->name);
 
 	hdlc->open = 1;
 

include/linux/hdlc.h

 /*
  * Generic HDLC support routines for Linux
  *
- * Copyright (C) 1999-2003 Krzysztof Halasa <khc@pm.waw.pl>
+ * Copyright (C) 1999-2005 Krzysztof Halasa <khc@pm.waw.pl>
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of version 2 of the GNU General Public License
@@ -41,6 +41,7 @@
 #define LMI_NONE		1 /* No LMI, all PVCs are static */
 #define LMI_ANSI		2 /* ANSI Annex D */
 #define LMI_CCITT		3 /* ITU-T Annex A */
+#define LMI_CISCO		4 /* The "original" LMI, aka Gang of Four */
 
 #define HDLC_MAX_MTU 1500	/* Ethernet 1500 bytes */
 #define HDLC_MAX_MRU (HDLC_MAX_MTU + 10 + 14 + 4) /* for ETH+VLAN over FR */
@@ -89,6 +90,7 @@ typedef struct pvc_device_struct {
 		unsigned int deleted: 1;
 		unsigned int fecn: 1;
 		unsigned int becn: 1;
+		unsigned int bandwidth;	/* Cisco LMI reporting only */
 	}state;
 }pvc_device;