Merge tag 'omap-for-v3.16/fixes-rc6' of...

Merge tag 'omap-for-v3.16/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Merge "Two regression fixes for omaps and one fix for device
signaling" from Tony Lindgren:

- L2 cache regression fix for a warning about trying to access
  a read-only register

- GPMC ECC software fallback regression fix for omap3

- Fix for dra7 pinctrl pull-up direction that causes signal issues
  for anybody trying to use the internal pull up or down

* tag 'omap-for-v3.16/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: gpmc: fix gpmc_hwecc_bch_capable()
  pinctrl: dra: dt-bindings: Fix pull enable/disable
  ARM: OMAP2+: l2c: squelch warning dump on power control setting
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm/mach-omap2/gpmc-nand.c

@@ -50,6 +50,16 @@ static bool gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt)
 		 soc_is_omap54xx() || soc_is_dra7xx())
 		return 1;
 
+	if (ecc_opt == OMAP_ECC_BCH4_CODE_HW_DETECTION_SW ||
+		 ecc_opt == OMAP_ECC_BCH8_CODE_HW_DETECTION_SW) {
+		if (cpu_is_omap24xx())
+			return 0;
+		else if (cpu_is_omap3630() && (GET_OMAP_REVISION() == 0))
+			return 0;
+		else
+			return 1;
+	}
+
 	/* OMAP3xxx do not have ELM engine, so cannot support ECC schemes
 	 * which require H/W based ECC error detection */
 	if ((cpu_is_omap34xx() || cpu_is_omap3630()) &&
@@ -57,14 +67,6 @@ static bool gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt)
 		 (ecc_opt == OMAP_ECC_BCH8_CODE_HW)))
 		return 0;
 
-	/*
-	 * For now, assume 4-bit mode is only supported on OMAP3630 ES1.x, x>=1
-	 * and AM33xx derivates. Other chips may be added if confirmed to work.
-	 */
-	if ((ecc_opt == OMAP_ECC_BCH4_CODE_HW_DETECTION_SW) &&
-	    (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0)))
-		return 0;
-
 	/* legacy platforms support only HAM1 (1-bit Hamming) ECC scheme */
 	if (ecc_opt == OMAP_ECC_HAM1_CODE_HW)
 		return 1;

arch/arm/mach-omap2/omap4-common.c

@@ -168,6 +168,10 @@ static void omap4_l2c310_write_sec(unsigned long val, unsigned reg)
 		smc_op = OMAP4_MON_L2X0_PREFETCH_INDEX;
 		break;
 
+	case L310_POWER_CTRL:
+		pr_info_once("OMAP L2C310: ROM does not support power control setting\n");
+		return;
+
 	default:
 		WARN_ONCE(1, "OMAP L2C310: ignoring write to reg 0x%x\n", reg);
 		return;

include/dt-bindings/pinctrl/dra.h

@@ -30,7 +30,8 @@
 #define MUX_MODE14	0xe
 #define MUX_MODE15	0xf
 
-#define PULL_ENA		(1 << 16)
+#define PULL_ENA		(0 << 16)
+#define PULL_DIS		(1 << 16)
 #define PULL_UP			(1 << 17)
 #define INPUT_EN		(1 << 18)
 #define SLEWCONTROL		(1 << 19)
@@ -38,10 +39,10 @@
 #define WAKEUP_EVENT		(1 << 25)
 
 /* Active pin states */
-#define PIN_OUTPUT		0
+#define PIN_OUTPUT		(0 | PULL_DIS)
 #define PIN_OUTPUT_PULLUP	(PIN_OUTPUT | PULL_ENA | PULL_UP)
 #define PIN_OUTPUT_PULLDOWN	(PIN_OUTPUT | PULL_ENA)
-#define PIN_INPUT		INPUT_EN
+#define PIN_INPUT		(INPUT_EN | PULL_DIS)
 #define PIN_INPUT_SLEW		(INPUT_EN | SLEWCONTROL)
 #define PIN_INPUT_PULLUP	(PULL_ENA | INPUT_EN | PULL_UP)
 #define PIN_INPUT_PULLDOWN	(PULL_ENA | INPUT_EN)