Merge branch 'ipmi' (emailed ipmi fixes)

Merge ipmi fixes from Corey Minyard:
 "Things collected since last kernel release.

  Some of these are pretty important.  The first three are bug fixes.
  The next two are to hopefully make everyone happy about allowing
  ACPI to be on all the time and not have IPMI have an effect on the
  system when not in use.  The last is a little cleanup"

* emailed patches from Corey Minyard <cminyard@mvista.com>:
  ipmi: boolify some things
  ipmi: Turn off all activity on an idle ipmi interface
  ipmi: Turn off default probing of interfaces
  ipmi: Reset the KCS timeout when starting error recovery
  ipmi: Fix a race restarting the timer
  Char: ipmi_bt_sm, fix infinite loop

drivers/char/ipmi/Kconfig

@@ -50,6 +50,18 @@ config IPMI_SI
 	 Currently, only KCS and SMIC are supported.  If
 	 you are using IPMI, you should probably say "y" here.
 
+config IPMI_SI_PROBE_DEFAULTS
+       bool 'Probe for all possible IPMI system interfaces by default'
+       default n
+       depends on IPMI_SI
+       help
+	 Modern systems will usually expose IPMI interfaces via a discoverable
+	 firmware mechanism such as ACPI or DMI. Older systems do not, and so
+	 the driver is forced to probe hardware manually. This may cause boot
+	 delays. Say "n" here to disable this manual probing. IPMI will then
+	 only be available on older systems if the "ipmi_si_intf.trydefaults=1"
+	 boot argument is passed.
+
 config IPMI_WATCHDOG
        tristate 'IPMI Watchdog Timer'
        help

drivers/char/ipmi/ipmi_bt_sm.c

@@ -352,7 +352,7 @@ static inline void write_all_bytes(struct si_sm_data *bt)
 
 static inline int read_all_bytes(struct si_sm_data *bt)
 {
-	unsigned char i;
+	unsigned int i;
 
 	/*
 	 * length is "framing info", minimum = 4: NetFn, Seq, Cmd, cCode.

drivers/char/ipmi/ipmi_kcs_sm.c

@@ -251,6 +251,7 @@ static inline int check_obf(struct si_sm_data *kcs, unsigned char status,
 	if (!GET_STATUS_OBF(status)) {
 		kcs->obf_timeout -= time;
 		if (kcs->obf_timeout < 0) {
+			kcs->obf_timeout = OBF_RETRY_TIMEOUT;
 			start_error_recovery(kcs, "OBF not ready in time");
 			return 1;
 		}

include/linux/ipmi.h

@@ -237,7 +237,7 @@ int ipmi_set_maintenance_mode(ipmi_user_t user, int mode);
  * The first user that sets this to TRUE will receive all events that
  * have been queued while no one was waiting for events.
  */
-int ipmi_set_gets_events(ipmi_user_t user, int val);
+int ipmi_set_gets_events(ipmi_user_t user, bool val);
 
 /*
  * Called when a new SMI is registered.  This will also be called on

include/linux/ipmi_smi.h

@@ -109,12 +109,19 @@ struct ipmi_smi_handlers {
 	   events from the BMC we are attached to. */
 	void (*request_events)(void *send_info);
 
+	/* Called by the upper layer when some user requires that the
+	   interface watch for events, received messages, watchdog
+	   pretimeouts, or not.  Used by the SMI to know if it should
+	   watch for these.  This may be NULL if the SMI does not
+	   implement it. */
+	void (*set_need_watch)(void *send_info, bool enable);
+
 	/* Called when the interface should go into "run to
 	   completion" mode.  If this call sets the value to true, the
 	   interface should make sure that all messages are flushed
 	   out and that none are pending, and any new requests are run
 	   to completion immediately. */
-	void (*set_run_to_completion)(void *send_info, int run_to_completion);
+	void (*set_run_to_completion)(void *send_info, bool run_to_completion);
 
 	/* Called to poll for work to do.  This is so upper layers can
 	   poll for operations during things like crash dumps. */
@@ -125,7 +132,7 @@ struct ipmi_smi_handlers {
 	   setting.  The message handler does the mode handling.  Note
 	   that this is called from interrupt context, so it cannot
 	   block. */
-	void (*set_maintenance_mode)(void *send_info, int enable);
+	void (*set_maintenance_mode)(void *send_info, bool enable);
 
 	/* Tell the handler that we are using it/not using it.  The
 	   message handler get the modules that this handler belongs