[PATCH] uml: fix mcast network driver error handling

printk clears the host errno (I verified this in debugging and it's reasonable
enough, given that it ends via a write call on some fd, especially since
printk() goes on /dev/tty0 which is often the host stdout).  So save errno
earlier.  There's no reason to change the printk calls to use -err rather than
errno - the assignment can't clear errno.

And in the first failure path, we used to return 0 too (and this time more
clearly), which is totally wrong.  0 is a success fd, which is then registered
and gives a "registering fd twice" warning.

Finally, fix up some whitespace.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

arch/um/drivers/mcast_user.c

@@ -54,7 +54,7 @@ static int mcast_open(void *data)
 	struct mcast_data *pri = data;
 	struct sockaddr_in *sin = pri->mcast_addr;
 	struct ip_mreq mreq;
-	int fd, yes = 1, err = 0;
+	int fd, yes = 1, err = -EINVAL;
 
 
 	if ((sin->sin_addr.s_addr == 0) || (sin->sin_port == 0))
@@ -63,40 +63,40 @@ static int mcast_open(void *data)
 	fd = socket(AF_INET, SOCK_DGRAM, 0);
 
 	if (fd < 0){
+		err = -errno;
 		printk("mcast_open : data socket failed, errno = %d\n", 
 		       errno);
-		err = -errno;
 		goto out;
 	}
 
 	if (setsockopt(fd, SOL_SOCKET, SO_REUSEADDR, &yes, sizeof(yes)) < 0) {
+		err = -errno;
 		printk("mcast_open: SO_REUSEADDR failed, errno = %d\n",
 			errno);
-		err = -errno;
 		goto out_close;
 	}
 
 	/* set ttl according to config */
 	if (setsockopt(fd, SOL_IP, IP_MULTICAST_TTL, &pri->ttl,
 		       sizeof(pri->ttl)) < 0) {
+		err = -errno;
 		printk("mcast_open: IP_MULTICAST_TTL failed, error = %d\n",
 			errno);
-		err = -errno;
 		goto out_close;
 	}
 
 	/* set LOOP, so data does get fed back to local sockets */
 	if (setsockopt(fd, SOL_IP, IP_MULTICAST_LOOP, &yes, sizeof(yes)) < 0) {
+		err = -errno;
 		printk("mcast_open: IP_MULTICAST_LOOP failed, error = %d\n",
 			errno);
-		err = -errno;
 		goto out_close;
 	}
 
 	/* bind socket to mcast address */
 	if (bind(fd, (struct sockaddr *) sin, sizeof(*sin)) < 0) {
-		printk("mcast_open : data bind failed, errno = %d\n", errno);
 		err = -errno;
+		printk("mcast_open : data bind failed, errno = %d\n", errno);
 		goto out_close;
 	}		
 	
@@ -105,13 +105,13 @@ static int mcast_open(void *data)
 	mreq.imr_interface.s_addr = 0;
 	if (setsockopt(fd, SOL_IP, IP_ADD_MEMBERSHIP, 
 		       &mreq, sizeof(mreq)) < 0) {
+		err = -errno;
 		printk("mcast_open: IP_ADD_MEMBERSHIP failed, error = %d\n",
 			errno);
 		printk("There appears not to be a multicast-capable network "
 		       "interface on the host.\n");
 		printk("eth0 should be configured in order to use the "
 		       "multicast transport.\n");
-		err = -errno;
 		goto out_close;
 	}