iwlwifi: read multiple MAC addresses

Some devices may have multiple MAC
addresses in their EEPROM, read them
and advertise them to cfg80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

drivers/net/wireless/iwlwifi/iwl-agn.c

@@ -3932,8 +3932,7 @@ static int iwl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	struct ieee80211_hw *hw;
 	struct iwl_cfg *cfg = (struct iwl_cfg *)(ent->driver_data);
 	unsigned long flags;
-	u16 pci_cmd;
-	u8 perm_addr[ETH_ALEN];
+	u16 pci_cmd, num_mac;
 
 	/************************
 	 * 1. Allocating HW data
@@ -4051,9 +4050,17 @@ static int iwl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 		goto out_free_eeprom;
 
 	/* extract MAC Address */
-	iwl_eeprom_get_mac(priv, perm_addr);
-	IWL_DEBUG_INFO(priv, "MAC address: %pM\n", perm_addr);
-	SET_IEEE80211_PERM_ADDR(priv->hw, perm_addr);
+	iwl_eeprom_get_mac(priv, priv->addresses[0].addr);
+	IWL_DEBUG_INFO(priv, "MAC address: %pM\n", priv->addresses[0].addr);
+	priv->hw->wiphy->addresses = priv->addresses;
+	priv->hw->wiphy->n_addresses = 1;
+	num_mac = iwl_eeprom_query16(priv, EEPROM_NUM_MAC_ADDRESS);
+	if (num_mac > 1) {
+		memcpy(priv->addresses[1].addr, priv->addresses[0].addr,
+		       ETH_ALEN);
+		priv->addresses[1].addr[5]++;
+		priv->hw->wiphy->n_addresses++;
+	}
 
 	/************************
 	 * 5. Setup HW constants

drivers/net/wireless/iwlwifi/iwl-dev.h

@@ -1154,6 +1154,9 @@ struct iwl_priv {
 	u32  hw_wa_rev;
 	u8   rev_id;
 
+	/* EEPROM MAC addresses */
+	struct mac_address addresses[2];
+
 	/* uCode images, save to reload in case of failure */
 	int fw_index;			/* firmware we're trying to load */
 	u32 ucode_ver;			/* version of ucode, copy of

drivers/net/wireless/iwlwifi/iwl-eeprom.h

@@ -402,6 +402,7 @@ struct iwl_eeprom_calib_info {
 #define EEPROM_WOWLAN_MODE                  (2*0x47)	/* 2  bytes */
 #define EEPROM_RADIO_CONFIG                 (2*0x48)	/* 2  bytes */
 #define EEPROM_3945_M_VERSION               (2*0x4A)	/* 1  bytes */
+#define EEPROM_NUM_MAC_ADDRESS              (2*0x4C)	/* 2  bytes */
 
 /* The following masks are to be applied on EEPROM_RADIO_CONFIG */
 #define EEPROM_RF_CFG_TYPE_MSK(x)   (x & 0x3)         /* bits 0-1   */