Support high-speed serial modes of National Semiconductor and SMSC Super-IO chips.

drivers/serial/8250.c

@@ -159,7 +159,8 @@ static const struct serial_uart_config uart_config[PORT_MAX_8250+1] = {
 	{ "16C950/954",	128,	UART_CLEAR_FIFO | UART_USE_FIFO },
 	{ "ST16654",	64,	UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
 	{ "XR16850",	128,	UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
-	{ "RSA",	2048,	UART_CLEAR_FIFO | UART_USE_FIFO }
+	{ "RSA",	2048,	UART_CLEAR_FIFO | UART_USE_FIFO },
+	{ "NS16550A",	16,	UART_CLEAR_FIFO | UART_USE_FIFO | UART_NATSEMI }
 };
 
 static _INLINE_ unsigned int serial_in(struct uart_8250_port *up, int offset)
@@ -481,6 +482,40 @@ static void autoconfig_16550a(struct uart_8250_port *up)
 		return;
 	}
 
+	/*
+	 * Check for a National Semiconductor SuperIO chip.
+	 * Attempt to switch to bank 2, read the value of the LOOP bit
+	 * from EXCR1. Switch back to bank 0, change it in MCR. Then
+	 * switch back to bank 2, read it from EXCR1 again and check
+	 * it's changed. If so, set baud_base in EXCR2 to 921600.
+	 */
+	serial_outp(up, UART_LCR, 0);
+	status1 = serial_in(up, UART_MCR);
+	serial_outp(up, UART_LCR, 0xE0);
+	status2 = serial_in(up, 0x02); /* EXCR1 */
+
+	if (!((status2 ^ status1) & UART_MCR_LOOP)) {
+		serial_outp(up, UART_LCR, 0);
+		serial_outp(up, UART_MCR, status1 ^ UART_MCR_LOOP);
+		serial_outp(up, UART_LCR, 0xE0);
+		status2 = serial_in(up, 0x02); /* EXCR1 */
+		serial_outp(up, UART_LCR, 0);
+		serial_outp(up, UART_MCR, status1);
+
+		if ((status2 ^ status1) & UART_MCR_LOOP) {
+			serial_outp(up, UART_LCR, 0xE0);
+			status1 = serial_in(up, 0x04); /* EXCR1 */
+			status1 &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
+			status1 |= 0x10;  /* 1.625 divisor for baud_base --> 921600 */
+			serial_outp(up, 0x04, status1);
+			serial_outp(up, UART_LCR, 0);
+
+			up->port.type = PORT_NS16550A;
+			up->port.uartclk = 921600*16;
+			return;
+		}
+	}
+
 	/*
 	 * No EFR.  Try to detect a TI16750, which only sets bit 5 of
 	 * the IIR when 64 byte FIFO mode is enabled when DLAB is set.
@@ -1318,6 +1353,26 @@ static void serial8250_shutdown(struct uart_port *port)
 		serial_unlink_irq_chain(up);
 }
 
+static unsigned int serial8250_get_divisor(struct uart_port *port, unsigned int baud)
+{
+	unsigned int quot;
+
+	/*
+	 * Handle magic divisors for baud rates above baud_base on
+	 * SMSC SuperIO chips.
+	 */
+	if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
+	    baud == (port->uartclk/4))
+		quot = 0x8001;
+	else if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
+		 baud == (port->uartclk/8))
+		quot = 0x8002;
+	else
+		quot = uart_get_divisor(port, baud);
+
+	return quot;
+}
+
 static void
 serial8250_set_termios(struct uart_port *port, struct termios *termios,
 		       struct termios *old)
@@ -1358,7 +1413,7 @@ serial8250_set_termios(struct uart_port *port, struct termios *termios,
 	 * Ask the core to calculate the divisor for us.
 	 */
 	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); 
-	quot = uart_get_divisor(port, baud);
+	quot = serial8250_get_divisor(port, baud);
 
 	/*
 	 * Work around a bug in the Oxford Semiconductor 952 rev B
@@ -1435,7 +1490,13 @@ serial8250_set_termios(struct uart_port *port, struct termios *termios,
 		serial_outp(up, UART_EFR,
 			    termios->c_cflag & CRTSCTS ? UART_EFR_CTS :0);
 	}
+
+	if (uart_config[up->port.type].flags & UART_NATSEMI) {
+		/* Switch to bank 2 not bank 1, to avoid resetting EXCR2 */
+		serial_outp(up, UART_LCR, 0xe0);
+	} else {
 		serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
+	}
 	serial_outp(up, UART_DLL, quot & 0xff);		/* LS of divisor */
 	serial_outp(up, UART_DLM, quot >> 8);		/* MS of divisor */
 	if (up->port.type == PORT_16750)

include/linux/serial.h

@@ -91,6 +91,7 @@ struct serial_uart_config {
 #define UART_CLEAR_FIFO		0x01
 #define UART_USE_FIFO		0x02
 #define UART_STARTECH		0x04
+#define UART_NATSEMI		0x08
 
 /*
  * Definitions for async_struct (and serial_struct) flags field

include/linux/serial_core.h

@@ -37,7 +37,8 @@
 #define PORT_16654	11
 #define PORT_16850	12
 #define PORT_RSA	13
-#define PORT_MAX_8250	13	/* max port ID */
+#define PORT_NS16550A	14
+#define PORT_MAX_8250	14	/* max port ID */
 
 /*
  * ARM specific type numbers.  These are not currently guaranteed
@@ -172,6 +173,7 @@ struct uart_port {
 #define UPF_LOW_LATENCY		(1 << 13)
 #define UPF_BUGGY_UART		(1 << 14)
 #define UPF_AUTOPROBE		(1 << 15)
+#define UPF_MAGIC_MULTIPLIER	(1 << 16)
 #define UPF_BOOT_ONLYMCA	(1 << 22)
 #define UPF_CONS_FLOW		(1 << 23)
 #define UPF_SHARE_IRQ		(1 << 24)
@@ -179,7 +181,7 @@ struct uart_port {
 #define UPF_RESOURCES		(1 << 30)
 #define UPF_IOREMAP		(1 << 31)
 
-#define UPF_CHANGE_MASK		(0x7fff)
+#define UPF_CHANGE_MASK		(0x17fff)
 #define UPF_USR_MASK		(UPF_SPD_MASK|UPF_LOW_LATENCY)
 
 	unsigned int		mctrl;			/* current modem ctrl settings */