drivers/net: delete old 8 bit ISA Racal ni5010 support.

These cards were only available in 8bit format, and in addition
they only had AUI and BNC(10-Base2) interfaces (i.e. no RJ-45).

In fact, they are so rare, that an internet search on these old
cards almost comes up empty, unless the "Micom interlan" name
is used.

This puts them in the equivalent domain as the 3c501, so there
should be no strong opposition to the driver removal, as nobody
is seriously using 3.9+ with 8 bit ISA hardware.

In doing so, the whole "ethernet/racal" category becomes empty,
so we clean up the Makefile/Kconfig and subdir appropriately.

Cc: Andreas Mohr <andi@lisas.de>
Cc: Jan-Pascal van Best <janpascal@vanbest.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

MAINTAINERS

@@ -5370,13 +5370,6 @@ F:	include/linux/sunrpc/
 F:	include/uapi/linux/nfs*
 F:	include/uapi/linux/sunrpc/
 
-NI5010 NETWORK DRIVER
-M:	Jan-Pascal van Best <janpascal@vanbest.org>
-M:	Andreas Mohr <andi@lisas.de>
-L:	netdev@vger.kernel.org
-S:	Maintained
-F:	drivers/net/ethernet/racal/ni5010.*
-
 NILFS2 FILESYSTEM
 M:	KONISHI Ryusuke <konishi.ryusuke@lab.ntt.co.jp>
 L:	linux-nilfs@vger.kernel.org

drivers/net/Space.c

@@ -50,7 +50,6 @@ extern struct net_device *eth16i_probe(int unit);
 extern struct net_device *i82596_probe(int unit);
 extern struct net_device *ewrk3_probe(int unit);
 extern struct net_device *e2100_probe(int unit);
-extern struct net_device *ni5010_probe(int unit);
 extern struct net_device *ni65_probe(int unit);
 extern struct net_device *sonic_probe(int unit);
 extern struct net_device *seeq8005_probe(int unit);
@@ -153,9 +152,6 @@ static struct devprobe2 isa_probes[] __initdata = {
 #if defined(CONFIG_MVME16x_NET) || defined(CONFIG_BVME6000_NET)	/* Intel I82596 */
 	{i82596_probe, 0},
 #endif
-#ifdef CONFIG_NI5010
-	{ni5010_probe, 0},
-#endif
 #ifdef CONFIG_NI65
 	{ni65_probe, 0},
 #endif

drivers/net/ethernet/Kconfig

@@ -135,7 +135,6 @@ config ETHOC
 source "drivers/net/ethernet/packetengines/Kconfig"
 source "drivers/net/ethernet/pasemi/Kconfig"
 source "drivers/net/ethernet/qlogic/Kconfig"
-source "drivers/net/ethernet/racal/Kconfig"
 source "drivers/net/ethernet/realtek/Kconfig"
 source "drivers/net/ethernet/renesas/Kconfig"
 source "drivers/net/ethernet/rdc/Kconfig"

drivers/net/ethernet/Makefile

@@ -53,7 +53,6 @@ obj-$(CONFIG_ETHOC) += ethoc.o
 obj-$(CONFIG_NET_PACKET_ENGINE) += packetengines/
 obj-$(CONFIG_NET_VENDOR_PASEMI) += pasemi/
 obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
-obj-$(CONFIG_NET_VENDOR_RACAL) += racal/
 obj-$(CONFIG_NET_VENDOR_REALTEK) += realtek/
 obj-$(CONFIG_SH_ETH) += renesas/
 obj-$(CONFIG_NET_VENDOR_RDC) += rdc/

drivers/net/ethernet/racal/Kconfig

-#
-# Racal-Interlan device configuration
-#
-
-config NET_VENDOR_RACAL
-	bool "Racal-Interlan (Micom) NI devices"
-	default y
-	depends on ISA
-	---help---
-	  If you have a network (Ethernet) card belonging to this class, such
-	  as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO,
-	  available from <http://www.tldp.org/docs.html#howto>.
-
-	  Note that the answer to this question doesn't directly affect the
-	  kernel: saying N will just cause the configurator to skip all
-	  the questions about NI cards. If you say Y, you will be asked for
-	  your specific card in the following questions.
-
-if NET_VENDOR_RACAL
-
-config NI5010
-	tristate "NI5010 support (EXPERIMENTAL)"
-	depends on ISA && EXPERIMENTAL && BROKEN_ON_SMP
-	---help---
-	  If you have a network (Ethernet) card of this type, say Y and read
-	  the Ethernet-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto>. Note that this is still
-	  experimental code.
-
-	  To compile this driver as a module, choose M here. The module
-	  will be called ni5010.
-
-endif # NET_VENDOR_RACAL

drivers/net/ethernet/racal/Makefile

-#
-# Makefile for the Racal-Interlan network device drivers.
-#
-
-obj-$(CONFIG_NI5010) += ni5010.o

drivers/net/ethernet/racal/ni5010.h

-/*
- * Racal-Interlan ni5010 Ethernet definitions
- *
- * This is an extension to the Linux operating system, and is covered by the
- * same GNU General Public License that covers that work.
- *
- * copyrights (c) 1996 by Jan-Pascal van Best (jvbest@wi.leidenuniv.nl)
- *
- * I have done a look in the following sources:
- *   crynwr-packet-driver by Russ Nelson
- */
-
-#define NI5010_BUFSIZE	2048	/* number of bytes in a buffer */
-
-#define NI5010_MAGICVAL0 0x00  /* magic-values for ni5010 card */
-#define NI5010_MAGICVAL1 0x55
-#define NI5010_MAGICVAL2 0xAA
-
-#define SA_ADDR0 0x02
-#define SA_ADDR1 0x07
-#define SA_ADDR2 0x01
-
-/* The number of low I/O ports used by the ni5010 ethercard. */
-#define NI5010_IO_EXTENT       32
-
-#define PRINTK(x) if (NI5010_DEBUG) printk x
-#define PRINTK2(x) if (NI5010_DEBUG>=2) printk x
-#define PRINTK3(x) if (NI5010_DEBUG>=3) printk x
-
-/* The various IE command registers */
-#define EDLC_XSTAT	(ioaddr + 0x00)	/* EDLC transmit csr */
-#define EDLC_XCLR	(ioaddr + 0x00)	/* EDLC transmit "Clear IRQ" */
-#define EDLC_XMASK	(ioaddr + 0x01)	/* EDLC transmit "IRQ Masks" */
-#define EDLC_RSTAT	(ioaddr + 0x02)	/* EDLC receive csr */
-#define EDLC_RCLR	(ioaddr + 0x02)	/* EDLC receive "Clear IRQ" */
-#define EDLC_RMASK	(ioaddr + 0x03)	/* EDLC receive "IRQ Masks" */
-#define EDLC_XMODE	(ioaddr + 0x04)	/* EDLC transmit Mode */
-#define EDLC_RMODE	(ioaddr + 0x05)	/* EDLC receive Mode */
-#define EDLC_RESET	(ioaddr + 0x06)	/* EDLC RESET register */
-#define EDLC_TDR1	(ioaddr + 0x07)	/* "Time Domain Reflectometry" reg1 */
-#define EDLC_ADDR	(ioaddr + 0x08)	/* EDLC station address, 6 bytes */
-	 			/* 0x0E doesn't exist for r/w */
-#define EDLC_TDR2	(ioaddr + 0x0f)	/* "Time Domain Reflectometry" reg2 */
-#define IE_GP		(ioaddr + 0x10)	/* GP pointer (word register) */
-				/* 0x11 is 2nd byte of GP Pointer */
-#define IE_RCNT		(ioaddr + 0x10)	/* Count of bytes in rcv'd packet */
- 				/* 0x11 is 2nd byte of "Byte Count" */
-#define IE_MMODE	(ioaddr + 0x12)	/* Memory Mode register */
-#define IE_DMA_RST	(ioaddr + 0x13)	/* IE DMA Reset.  write only */
-#define IE_ISTAT	(ioaddr + 0x13)	/* IE Interrupt Status.  read only */
-#define IE_RBUF		(ioaddr + 0x14)	/* IE Receive Buffer port */
-#define IE_XBUF		(ioaddr + 0x15)	/* IE Transmit Buffer port */
-#define IE_SAPROM	(ioaddr + 0x16)	/* window on station addr prom */
-#define IE_RESET	(ioaddr + 0x17)	/* any write causes Board Reset */
-
-/* bits in EDLC_XSTAT, interrupt clear on write, status when read */
-#define XS_TPOK		0x80	/* transmit packet successful */
-#define XS_CS		0x40	/* carrier sense */
-#define XS_RCVD		0x20	/* transmitted packet received */
-#define XS_SHORT	0x10	/* transmission media is shorted */
-#define XS_UFLW		0x08	/* underflow.  iff failed board */
-#define XS_COLL		0x04	/* collision occurred */
-#define XS_16COLL	0x02	/* 16th collision occurred */
-#define XS_PERR		0x01	/* parity error */
-
-#define XS_CLR_UFLW	0x08	/* clear underflow */
-#define XS_CLR_COLL	0x04	/* clear collision */
-#define XS_CLR_16COLL	0x02	/* clear 16th collision */
-#define XS_CLR_PERR	0x01	/* clear parity error */
-
-/* bits in EDLC_XMASK, mask/enable transmit interrupts.  register is r/w */
-#define XM_TPOK		0x80	/* =1 to enable Xmt Pkt OK interrupts */
-#define XM_RCVD		0x20	/* =1 to enable Xmt Pkt Rcvd ints */
-#define XM_UFLW		0x08	/* =1 to enable Xmt Underflow ints */
-#define XM_COLL		0x04	/* =1 to enable Xmt Collision ints */
-#define XM_COLL16	0x02	/* =1 to enable Xmt 16th Coll ints */
-#define XM_PERR		0x01	/* =1 to enable Xmt Parity Error ints */
- 				/* note: always clear this bit */
-#define XM_ALL		(XM_TPOK | XM_RCVD | XM_UFLW | XM_COLL | XM_COLL16)
-
-/* bits in EDLC_RSTAT, interrupt clear on write, status when read */
-#define RS_PKT_OK	0x80	/* received good packet */
-#define RS_RST_PKT	0x10	/* RESET packet received */
-#define RS_RUNT		0x08	/* Runt Pkt rcvd.  Len < 64 Bytes */
-#define RS_ALIGN	0x04	/* Alignment error. not 8 bit aligned */
-#define RS_CRC_ERR	0x02	/* Bad CRC on rcvd pkt */
-#define RS_OFLW		0x01	/* overflow for rcv FIFO */
-#define RS_VALID_BITS	( RS_PKT_OK | RS_RST_PKT | RS_RUNT | RS_ALIGN | RS_CRC_ERR | RS_OFLW )
- 				/* all valid RSTAT bits */
-
-#define RS_CLR_PKT_OK	0x80	/* clear rcvd packet interrupt */
-#define RS_CLR_RST_PKT	0x10	/* clear RESET packet received */
-#define RS_CLR_RUNT	0x08	/* clear Runt Pckt received */
-#define RS_CLR_ALIGN	0x04	/* clear Alignment error */
-#define RS_CLR_CRC_ERR	0x02	/* clear CRC error */
-#define RS_CLR_OFLW	0x01	/* clear rcv FIFO Overflow */
-
-/* bits in EDLC_RMASK, mask/enable receive interrupts.  register is r/w */
-#define RM_PKT_OK	0x80	/* =1 to enable rcvd good packet ints */
-#define RM_RST_PKT	0x10	/* =1 to enable RESET packet ints */
-#define RM_RUNT		0x08	/* =1 to enable Runt Pkt rcvd ints */
-#define RM_ALIGN	0x04	/* =1 to enable Alignment error ints */
-#define RM_CRC_ERR	0x02	/* =1 to enable Bad CRC error ints */
-#define RM_OFLW		0x01	/* =1 to enable overflow error ints */
-
-/* bits in EDLC_RMODE, set Receive Packet mode.  register is r/w */
-#define RMD_TEST	0x80	/* =1 for Chip testing.  normally 0 */
-#define RMD_ADD_SIZ	0x10	/* =1 5-byte addr match.  normally 0 */
-#define RMD_EN_RUNT	0x08	/* =1 enable runt rcv.  normally 0 */
-#define RMD_EN_RST	0x04	/* =1 to rcv RESET pkt.  normally 0 */
-
-#define RMD_PROMISC	0x03	/* receive *all* packets.  unusual */
-#define RMD_MULTICAST	0x02	/* receive multicasts too.  unusual */
-#define RMD_BROADCAST	0x01	/* receive broadcasts & normal. usual */
-#define RMD_NO_PACKETS	0x00	/* don't receive any packets. unusual */
-
-/* bits in EDLC_XMODE, set Transmit Packet mode.  register is r/w */
-#define XMD_COLL_CNT	0xf0	/* coll's since success.  read-only */
-#define XMD_IG_PAR	0x08	/* =1 to ignore parity.  ALWAYS set */
-#define XMD_T_MODE	0x04	/* =1 to power xcvr. ALWAYS set this */
-#define XMD_LBC		0x02	/* =1 for loopbakc.  normally set */
-#define XMD_DIS_C	0x01	/* =1 disables contention. normally 0 */
-
-/* bits in EDLC_RESET, write only */
-#define RS_RESET	0x80	/* =1 to hold EDLC in reset state */
-
-/* bits in IE_MMODE, write only */
-#define MM_EN_DMA	0x80	/* =1 begin DMA xfer, Cplt clrs it */
-#define MM_EN_RCV	0x40	/* =1 allows Pkt rcv.  clr'd by rcv */
-#define MM_EN_XMT	0x20	/* =1 begin Xmt pkt.  Cplt clrs it */
-#define MM_BUS_PAGE	0x18	/* =00 ALWAYS.  Used when MUX=1 */
-#define MM_NET_PAGE	0x06	/* =00 ALWAYS.  Used when MUX=0 */
-#define MM_MUX		0x01	/* =1 means Rcv Buff on system bus */
-				/* =0 means Xmt Buff on system bus */
-
-/* bits in IE_ISTAT, read only */
-#define IS_TDIAG	0x80	/* =1 if Diagnostic problem */
-#define IS_EN_RCV	0x20	/* =1 until frame is rcv'd cplt */
-#define IS_EN_XMT	0x10	/* =1 until frame is xmt'd cplt */
-#define IS_EN_DMA	0x08	/* =1 until DMA is cplt or aborted */
-#define IS_DMA_INT	0x04	/* =0 iff DMA done interrupt. */
-#define IS_R_INT	0x02	/* =0 iff unmasked Rcv interrupt */
-#define IS_X_INT	0x01	/* =0 iff unmasked Xmt interrupt */
-