staging: comedi: pcl818: convert printk() messages to dev_{level}

Convert the remaining printk messsages in this driver to dev_{level}.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/comedi/drivers/pcl818.c

@@ -463,8 +463,8 @@ static irqreturn_t interrupt_pcl818_ai_mode13_int(int irq, void *d)
 	outb(0, dev->iobase + PCL818_CLRINT);	/* clear INT request */
 
 	if ((low & 0xf) != devpriv->act_chanlist[devpriv->act_chanlist_pos]) {	/*  dropout! */
-		printk
-		    ("comedi: A/D mode1/3 IRQ - channel dropout %x!=%x !\n",
+		dev_dbg(dev->class_dev,
+			"A/D mode1/3 IRQ - channel dropout %x!=%x !\n",
 			(low & 0xf),
 			devpriv->act_chanlist[devpriv->act_chanlist_pos]);
 		pcl818_ai_cancel(dev, s);
@@ -532,8 +532,8 @@ static irqreturn_t interrupt_pcl818_ai_mode13_dma(int irq, void *d)
 
 	for (i = 0; i < len; i++) {
 		if ((ptr[bufptr] & 0xf) != devpriv->act_chanlist[devpriv->act_chanlist_pos]) {	/*  dropout! */
-			printk
-			    ("comedi: A/D mode1/3 DMA - channel dropout %d(card)!=%d(chanlist) at %d !\n",
+			dev_dbg(dev->class_dev,
+				"A/D mode1/3 DMA - channel dropout %d(card)!=%d(chanlist) at %d !\n",
 				(ptr[bufptr] & 0xf),
 				devpriv->act_chanlist[devpriv->act_chanlist_pos],
 				devpriv->act_chanlist_pos);
@@ -609,8 +609,8 @@ static irqreturn_t interrupt_pcl818_ai_mode13_fifo(int irq, void *d)
 	for (i = 0; i < len; i++) {
 		lo = inb(dev->iobase + PCL818_FI_DATALO);
 		if ((lo & 0xf) != devpriv->act_chanlist[devpriv->act_chanlist_pos]) {	/*  dropout! */
-			printk
-			    ("comedi: A/D mode1/3 FIFO - channel dropout %d!=%d !\n",
+			dev_dbg(dev->class_dev,
+				"A/D mode1/3 FIFO - channel dropout %d!=%d !\n",
 				(lo & 0xf),
 				devpriv->act_chanlist[devpriv->act_chanlist_pos]);
 			pcl818_ai_cancel(dev, s);
@@ -1249,7 +1249,8 @@ static int pcl818_attach(struct comedi_device *dev, struct comedi_devconfig *it)
 		if (dma < 1)
 			goto no_dma;	/* DMA disabled */
 		if (((1 << dma) & board->DMAbits) == 0) {
-			printk(KERN_ERR "DMA is out of allowed range, FAIL!\n");
+			dev_err(dev->class_dev,
+				"DMA is out of allowed range, FAIL!\n");
 			return -EINVAL;	/* Bad DMA */
 		}
 		ret = request_dma(dma, dev->board_name);