Commit da58a931 authored by Maxime Chevallier's avatar Maxime Chevallier Committed by David S. Miller

net: mvneta: Add support for 2500Mbps SGMII

The mvneta controller can handle speeds up to 2500Mbps on the SGMII
interface. This relies on serdes configuration, the lane must be
configured at 3.125Gbps and we can't use in-band autoneg at that speed.

The main issue when supporting that speed on this particular controller
is that the link partner can send ethernet frames with a shortened
preamble, which if not explicitly enabled in the controller will cause
unexpected behaviours.

This was tested on Armada 385, with the comphy configuration done in
bootloader.
Signed-off-by: default avatarMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent c09c1474
......@@ -221,6 +221,8 @@
#define MVNETA_GMAC_AN_FLOW_CTRL_EN BIT(11)
#define MVNETA_GMAC_CONFIG_FULL_DUPLEX BIT(12)
#define MVNETA_GMAC_AN_DUPLEX_EN BIT(13)
#define MVNETA_GMAC_CTRL_4 0x2c90
#define MVNETA_GMAC4_SHORT_PREAMBLE_ENABLE BIT(1)
#define MVNETA_MIB_COUNTERS_BASE 0x3000
#define MVNETA_MIB_LATE_COLLISION 0x7c
#define MVNETA_DA_FILT_SPEC_MCAST 0x3400
......@@ -3341,6 +3343,7 @@ static void mvneta_validate(struct net_device *ndev, unsigned long *supported,
if (state->interface != PHY_INTERFACE_MODE_NA &&
state->interface != PHY_INTERFACE_MODE_QSGMII &&
state->interface != PHY_INTERFACE_MODE_SGMII &&
state->interface != PHY_INTERFACE_MODE_2500BASEX &&
!phy_interface_mode_is_8023z(state->interface) &&
!phy_interface_mode_is_rgmii(state->interface)) {
bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
......@@ -3353,9 +3356,15 @@ static void mvneta_validate(struct net_device *ndev, unsigned long *supported,
/* Asymmetric pause is unsupported */
phylink_set(mask, Pause);
/* Half-duplex at speeds higher than 100Mbit is unsupported */
/* We cannot use 1Gbps when using the 2.5G interface. */
if (state->interface == PHY_INTERFACE_MODE_2500BASEX) {
phylink_set(mask, 2500baseT_Full);
phylink_set(mask, 2500baseX_Full);
} else {
phylink_set(mask, 1000baseT_Full);
phylink_set(mask, 1000baseX_Full);
}
if (!phy_interface_mode_is_8023z(state->interface)) {
/* 10M and 100M are only supported in non-802.3z mode */
......@@ -3416,12 +3425,14 @@ static void mvneta_mac_config(struct net_device *ndev, unsigned int mode,
struct mvneta_port *pp = netdev_priv(ndev);
u32 new_ctrl0, gmac_ctrl0 = mvreg_read(pp, MVNETA_GMAC_CTRL_0);
u32 new_ctrl2, gmac_ctrl2 = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
u32 new_ctrl4, gmac_ctrl4 = mvreg_read(pp, MVNETA_GMAC_CTRL_4);
u32 new_clk, gmac_clk = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
u32 new_an, gmac_an = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
new_ctrl0 = gmac_ctrl0 & ~MVNETA_GMAC0_PORT_1000BASE_X;
new_ctrl2 = gmac_ctrl2 & ~(MVNETA_GMAC2_INBAND_AN_ENABLE |
MVNETA_GMAC2_PORT_RESET);
new_ctrl4 = gmac_ctrl4 & ~(MVNETA_GMAC4_SHORT_PREAMBLE_ENABLE);
new_clk = gmac_clk & ~MVNETA_GMAC_1MS_CLOCK_ENABLE;
new_an = gmac_an & ~(MVNETA_GMAC_INBAND_AN_ENABLE |
MVNETA_GMAC_INBAND_RESTART_AN |
......@@ -3454,7 +3465,7 @@ static void mvneta_mac_config(struct net_device *ndev, unsigned int mode,
if (state->duplex)
new_an |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
if (state->speed == SPEED_1000)
if (state->speed == SPEED_1000 || state->speed == SPEED_2500)
new_an |= MVNETA_GMAC_CONFIG_GMII_SPEED;
else if (state->speed == SPEED_100)
new_an |= MVNETA_GMAC_CONFIG_MII_SPEED;
......@@ -3493,10 +3504,18 @@ static void mvneta_mac_config(struct net_device *ndev, unsigned int mode,
MVNETA_GMAC_FORCE_LINK_DOWN);
}
/* When at 2.5G, the link partner can send frames with shortened
* preambles.
*/
if (state->speed == SPEED_2500)
new_ctrl4 |= MVNETA_GMAC4_SHORT_PREAMBLE_ENABLE;
if (new_ctrl0 != gmac_ctrl0)
mvreg_write(pp, MVNETA_GMAC_CTRL_0, new_ctrl0);
if (new_ctrl2 != gmac_ctrl2)
mvreg_write(pp, MVNETA_GMAC_CTRL_2, new_ctrl2);
if (new_ctrl4 != gmac_ctrl4)
mvreg_write(pp, MVNETA_GMAC_CTRL_4, new_ctrl4);
if (new_clk != gmac_clk)
mvreg_write(pp, MVNETA_GMAC_CLOCK_DIVIDER, new_clk);
if (new_an != gmac_an)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment