Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "Here's a set of patches for (hopefully) -rc1.  Some of them are fixes,
  but a good number of them also do things such as enable new drivers in
  the defconfigs for platforms that have such devices, increases
  coverage of the multiplatform defconfig and some DTS changes that
  plumbs up some of the devices that now have bindings and driver
  support.

  The commit dates are recent; we've mostly collected these fixes in the
  last few days but I also had to rebuild the branch yesterday to sort
  out some internal conflicts which reset the timestamps.  The changes
  should have been tested by each platform maintainer already (and few
  of them have cross-platform impact) so I'm personally not too
  concerned by it at this time"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
  ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
  ARM: multi_v7_defconfig: add mvebu drivers
  clocksource: kona: Add basic use of external clock
  drivers: bus: fix CCI driver kcalloc call parameters swap
  ARM: dts: bcm28155-ap: Fix Card Detection GPIO
  ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY
  ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set
  MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
  ARM: dts: zynq: Add SDHCI nodes
  ARM: hisi: don't select SMP
  ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
  ARM: multi_v7: copy most options from tegra_defconfig
  ARM: iop32x: fix power off handling for the EM7210 board
  ARM: integrator: restore static map on the CP
  ARM: msm_defconfig: Enable MSM clock drivers
  ARM: dts: msm: Add clock controller nodes and hook into uart
  ARM: OMAP4+: move errata initialization to omap4_pm_init_early
  ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
  ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
  ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
  ...

MAINTAINERS

@@ -868,14 +868,7 @@ F:	arch/arm/mach-prima2/
 F:	drivers/clk/clk-prima2.c
 F:	drivers/clocksource/timer-prima2.c
 F:	drivers/clocksource/timer-marco.c
-F:	drivers/dma/sirf-dma.c
-F:	drivers/i2c/busses/i2c-sirf.c
-F:	drivers/input/misc/sirfsoc-onkey.c
-F:	drivers/irqchip/irq-sirfsoc.c
-F:	drivers/mmc/host/sdhci-sirf.c
-F:	drivers/pinctrl/sirf/
-F:	drivers/rtc/rtc-sirfsoc.c
-F:	drivers/spi/spi-sirf.c
+N:	[^a-z]sirf
 
 ARM/EBSA110 MACHINE SUPPORT
 M:	Russell King <linux@arm.linux.org.uk>

arch/arm/boot/dts/bcm28155-ap.dts

@@ -13,6 +13,8 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
+
 #include "bcm11351.dtsi"
 
 / {
@@ -60,7 +62,7 @@ sdio2: sdio@3f190000 {
 
 	sdio4: sdio@3f1b0000 {
 		max-frequency = <48000000>;
-		cd-gpios = <&gpio 14 0>;
+		cd-gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
 		status = "okay";
 	};
 

arch/arm/boot/dts/qcom-msm8660-surf.dts

@@ -2,6 +2,8 @@
 
 /include/ "skeleton.dtsi"
 
+#include <dt-bindings/clock/qcom,gcc-msm8660.h>
+
 / {
 	model = "Qualcomm MSM8660 SURF";
 	compatible = "qcom,msm8660-surf", "qcom,msm8660";
@@ -37,11 +39,20 @@ msmgpio: gpio@800000 {
 		#interrupt-cells = <2>;
 	};
 
+	gcc: clock-controller@900000 {
+		compatible = "qcom,gcc-msm8660";
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+		reg = <0x900000 0x4000>;
+	};
+
 	serial@19c40000 {
 		compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 		reg = <0x19c40000 0x1000>,
 		      <0x19c00000 0x1000>;
 		interrupts = <0 195 0x0>;
+		clocks = <&gcc GSBI12_UART_CLK>, <&gcc GSBI12_H_CLK>;
+		clock-names = "core", "iface";
 	};
 
 	qcom,ssbi@500000 {

arch/arm/boot/dts/qcom-msm8960-cdp.dts

@@ -2,6 +2,8 @@
 
 /include/ "skeleton.dtsi"
 
+#include <dt-bindings/clock/qcom,gcc-msm8960.h>
+
 / {
 	model = "Qualcomm MSM8960 CDP";
 	compatible = "qcom,msm8960-cdp", "qcom,msm8960";
@@ -37,11 +39,27 @@ msmgpio: gpio@800000 {
 		reg = <0x800000 0x4000>;
 	};
 
+	gcc: clock-controller@900000 {
+		compatible = "qcom,gcc-msm8960";
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+		reg = <0x900000 0x4000>;
+	};
+
+	clock-controller@4000000 {
+		compatible = "qcom,mmcc-msm8960";
+		reg = <0x4000000 0x1000>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
+
 	serial@16440000 {
 		compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 		reg = <0x16440000 0x1000>,
 		      <0x16400000 0x1000>;
 		interrupts = <0 154 0x0>;
+		clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
+		clock-names = "core", "iface";
 	};
 
 	qcom,ssbi@500000 {

arch/arm/boot/dts/qcom-msm8974.dtsi

@@ -2,6 +2,8 @@
 
 #include "skeleton.dtsi"
 
+#include <dt-bindings/clock/qcom,gcc-msm8974.h>
+
 / {
 	model = "Qualcomm MSM8974";
 	compatible = "qcom,msm8974";
@@ -93,5 +95,27 @@ restart@fc4ab000 {
 			compatible = "qcom,pshold";
 			reg = <0xfc4ab000 0x4>;
 		};
+
+		gcc: clock-controller@fc400000 {
+			compatible = "qcom,gcc-msm8974";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0xfc400000 0x4000>;
+		};
+
+		mmcc: clock-controller@fd8c0000 {
+			compatible = "qcom,mmcc-msm8974";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0xfd8c0000 0x6000>;
+		};
+
+		serial@f991e000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991e000 0x1000>;
+			interrupts = <0 108 0x0>;
+			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+		};
 	};
 };

arch/arm/boot/dts/r8a7790.dtsi

@@ -197,7 +197,7 @@ i2c0: i2c@e6508000 {
 		reg = <0 0xe6508000 0 0x40>;
 		interrupt-parent = <&gic>;
 		interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&mstp3_clks R8A7790_CLK_I2C0>;
+		clocks = <&mstp9_clks R8A7790_CLK_I2C0>;
 		status = "disabled";
 	};
 
@@ -208,7 +208,7 @@ i2c1: i2c@e6518000 {
 		reg = <0 0xe6518000 0 0x40>;
 		interrupt-parent = <&gic>;
 		interrupts = <0 288 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&mstp3_clks R8A7790_CLK_I2C1>;
+		clocks = <&mstp9_clks R8A7790_CLK_I2C1>;
 		status = "disabled";
 	};
 
@@ -219,7 +219,7 @@ i2c2: i2c@e6530000 {
 		reg = <0 0xe6530000 0 0x40>;
 		interrupt-parent = <&gic>;
 		interrupts = <0 286 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&mstp3_clks R8A7790_CLK_I2C2>;
+		clocks = <&mstp9_clks R8A7790_CLK_I2C2>;
 		status = "disabled";
 	};
 
@@ -230,7 +230,7 @@ i2c3: i2c@e6540000 {
 		reg = <0 0xe6540000 0 0x40>;
 		interrupt-parent = <&gic>;
 		interrupts = <0 290 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&mstp3_clks R8A7790_CLK_I2C3>;
+		clocks = <&mstp9_clks R8A7790_CLK_I2C3>;
 		status = "disabled";
 	};
 

arch/arm/boot/dts/zynq-7000.dtsi

@@ -102,6 +102,26 @@ gem1: ethernet@e000c000 {
 			clock-names = "pclk", "hclk", "tx_clk";
 		};
 
+		sdhci0: ps7-sdhci@e0100000 {
+			compatible = "arasan,sdhci-8.9a";
+			status = "disabled";
+			clock-names = "clk_xin", "clk_ahb";
+			clocks = <&clkc 21>, <&clkc 32>;
+			interrupt-parent = <&intc>;
+			interrupts = <0 24 4>;
+			reg = <0xe0100000 0x1000>;
+		} ;
+
+		sdhci1: ps7-sdhci@e0101000 {
+			compatible = "arasan,sdhci-8.9a";
+			status = "disabled";
+			clock-names = "clk_xin", "clk_ahb";
+			clocks = <&clkc 22>, <&clkc 33>;
+			interrupt-parent = <&intc>;
+			interrupts = <0 47 4>;
+			reg = <0xe0101000 0x1000>;
+		} ;
+
 		slcr: slcr@f8000000 {
 			compatible = "xlnx,zynq-slcr";
 			reg = <0xF8000000 0x1000>;

arch/arm/boot/dts/zynq-zc702.dts

@@ -34,6 +34,10 @@ &gem0 {
 	phy-mode = "rgmii";
 };
 
+&sdhci0 {
+	status = "okay";
+};
+
 &uart1 {
 	status = "okay";
 };

arch/arm/boot/dts/zynq-zc706.dts

@@ -35,6 +35,10 @@ &gem0 {
 	phy-mode = "rgmii";
 };
 
+&sdhci0 {
+	status = "okay";
+};
+
 &uart1 {
 	status = "okay";
 };

arch/arm/boot/dts/zynq-zed.dts

@@ -35,6 +35,10 @@ &gem0 {
 	phy-mode = "rgmii";
 };
 
+&sdhci0 {
+	status = "okay";
+};
+
 &uart1 {
 	status = "okay";
 };

arch/arm/configs/keystone_defconfig

@@ -142,6 +142,7 @@ CONFIG_USB_DWC3_DEBUG=y
 CONFIG_USB_DWC3_VERBOSE=y
 CONFIG_KEYSTONE_USB_PHY=y
 CONFIG_DMADEVICES=y
+CONFIG_TI_EDMA=y
 CONFIG_COMMON_CLK_DEBUG=y
 CONFIG_MEMORY=y
 CONFIG_EXT4_FS=y

arch/arm/configs/msm_defconfig

@@ -114,6 +114,10 @@ CONFIG_USB_GADGET_VBUS_DRAW=500
 CONFIG_NEW_LEDS=y
 CONFIG_RTC_CLASS=y
 CONFIG_STAGING=y
+CONFIG_COMMON_CLK_QCOM=y
+CONFIG_MSM_GCC_8660=y
+CONFIG_MSM_MMCC_8960=y
+CONFIG_MSM_MMCC_8974=y
 CONFIG_MSM_IOMMU=y
 CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y

arch/arm/configs/multi_v7_defconfig

+CONFIG_SYSVIPC=y
 CONFIG_IRQ_DOMAIN_DEBUG=y
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_EMBEDDED=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_ARCH_MVEBU=y
 CONFIG_MACH_ARMADA_370=y
 CONFIG_MACH_ARMADA_XP=y
@@ -38,7 +43,7 @@ CONFIG_ARCH_TEGRA=y
 CONFIG_ARCH_TEGRA_2x_SOC=y
 CONFIG_ARCH_TEGRA_3x_SOC=y
 CONFIG_ARCH_TEGRA_114_SOC=y
-CONFIG_TEGRA_PCI=y
+CONFIG_ARCH_TEGRA_124_SOC=y
 CONFIG_TEGRA_EMC_SCALING_ENABLE=y
 CONFIG_ARCH_U8500=y
 CONFIG_MACH_HREFV60=y
@@ -49,19 +54,55 @@ CONFIG_ARCH_VEXPRESS_CA9X4=y
 CONFIG_ARCH_VIRT=y
 CONFIG_ARCH_WM8850=y
 CONFIG_ARCH_ZYNQ=y
+CONFIG_TRUSTED_FOUNDATIONS=y
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
+CONFIG_PCI_MVEBU=y
+CONFIG_PCI_TEGRA=y
 CONFIG_SMP=y
 CONFIG_HIGHPTE=y
+CONFIG_CMA=y
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
+CONFIG_KEXEC=y
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_STAT_DETAILS=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
+CONFIG_CPU_IDLE=y
 CONFIG_NET=y
+CONFIG_PACKET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
 CONFIG_IP_PNP=y
 CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_OPTIMISTIC_DAD=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_MIP6=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_RFKILL=y
+CONFIG_RFKILL_INPUT=y
+CONFIG_RFKILL_GPIO=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_DMA_CMA=y
 CONFIG_OMAP_OCP2SCP=y
+CONFIG_MTD=y
+CONFIG_MTD_M25P80=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_ICS932S401=y
+CONFIG_APDS9802ALS=y
+CONFIG_ISL29003=y
 CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=y
+CONFIG_SCSI_MULTI_LUN=y
 CONFIG_ATA=y
 CONFIG_SATA_AHCI_PLATFORM=y
 CONFIG_SATA_HIGHBANK=y
@@ -69,13 +110,30 @@ CONFIG_SATA_MV=y
 CONFIG_NETDEVICES=y
 CONFIG_SUN4I_EMAC=y
 CONFIG_NET_CALXEDA_XGMAC=y
+CONFIG_MVNETA=y
 CONFIG_KS8851=y
+CONFIG_R8169=y
 CONFIG_SMSC911X=y
 CONFIG_STMMAC_ETH=y
-CONFIG_ICPLUS_PHY=y
-CONFIG_MDIO_SUN4I=y
 CONFIG_TI_CPSW=y
+CONFIG_AT803X_PHY=y
+CONFIG_MARVELL_PHY=y
+CONFIG_ICPLUS_PHY=y
+CONFIG_USB_PEGASUS=y
+CONFIG_USB_USBNET=y
+CONFIG_USB_NET_SMSC75XX=y
+CONFIG_USB_NET_SMSC95XX=y
+CONFIG_BRCMFMAC=m
+CONFIG_RT2X00=m
+CONFIG_RT2800USB=m
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_KEYBOARD_TEGRA=y
 CONFIG_KEYBOARD_SPEAR=y
+CONFIG_KEYBOARD_CROS_EC=y
+CONFIG_MOUSE_PS2_ELANTECH=y
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_MPU3050=y
 CONFIG_SERIO_AMBAKMI=y
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
@@ -98,30 +156,81 @@ CONFIG_SERIAL_FSL_LPUART=y
 CONFIG_SERIAL_FSL_LPUART_CONSOLE=y
 CONFIG_SERIAL_ST_ASC=y
 CONFIG_SERIAL_ST_ASC_CONSOLE=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PINCTRL=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
+CONFIG_I2C_MV64XXX=y
 CONFIG_I2C_SIRF=y
 CONFIG_I2C_TEGRA=y
 CONFIG_SPI=y
 CONFIG_SPI_OMAP24XX=y
+CONFIG_SPI_ORION=y
 CONFIG_SPI_PL022=y
 CONFIG_SPI_SIRF=y
 CONFIG_SPI_TEGRA114=y
+CONFIG_SPI_TEGRA20_SFLASH=y
 CONFIG_SPI_TEGRA20_SLINK=y
-CONFIG_PINCTRL_SINGLE=y
+CONFIG_PINCTRL_AS3722=y
+CONFIG_PINCTRL_PALMAS=y
+CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_GENERIC_PLATFORM=y
+CONFIG_GPIO_PCA953X_IRQ=y
 CONFIG_GPIO_TWL4030=y
-CONFIG_REGULATOR_GPIO=y
+CONFIG_GPIO_PALMAS=y
+CONFIG_GPIO_TPS6586X=y
+CONFIG_GPIO_TPS65910=y
+CONFIG_BATTERY_SBS=y
+CONFIG_CHARGER_TPS65090=y
+CONFIG_POWER_RESET_AS3722=y
+CONFIG_POWER_RESET_GPIO=y
+CONFIG_SENSORS_LM90=y
+CONFIG_THERMAL=y
+CONFIG_ARMADA_THERMAL=y
+CONFIG_MFD_AS3722=y
+CONFIG_MFD_CROS_EC=y
+CONFIG_MFD_CROS_EC_SPI=y
+CONFIG_MFD_MAX8907=y
+CONFIG_MFD_PALMAS=y
+CONFIG_MFD_TPS65090=y
+CONFIG_MFD_TPS6586X=y
+CONFIG_MFD_TPS65910=y
+CONFIG_REGULATOR_VIRTUAL_CONSUMER=y
 CONFIG_REGULATOR_AB8500=y
+CONFIG_REGULATOR_AS3722=y
+CONFIG_REGULATOR_GPIO=y
+CONFIG_REGULATOR_MAX8907=y
+CONFIG_REGULATOR_PALMAS=y
 CONFIG_REGULATOR_TPS51632=y
 CONFIG_REGULATOR_TPS62360=y
+CONFIG_REGULATOR_TPS65090=y
+CONFIG_REGULATOR_TPS6586X=y
+CONFIG_REGULATOR_TPS65910=y
 CONFIG_REGULATOR_TWL4030=y
 CONFIG_REGULATOR_VEXPRESS=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_DRM=y
-CONFIG_TEGRA_HOST1X=y
 CONFIG_DRM_TEGRA=y
+CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_FB_ARMCLCD=y
 CONFIG_FB_WM8505=y
 CONFIG_FB_SIMPLE=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_SOC=y
+CONFIG_SND_SOC_TEGRA=y
+CONFIG_SND_SOC_TEGRA_RT5640=y
+CONFIG_SND_SOC_TEGRA_WM8753=y
+CONFIG_SND_SOC_TEGRA_WM8903=y
+CONFIG_SND_SOC_TEGRA_TRIMSLICE=y
+CONFIG_SND_SOC_TEGRA_ALC5632=y
+CONFIG_SND_SOC_TEGRA_MAX98090=y
 CONFIG_USB=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_EHCI_HCD=y
@@ -132,8 +241,6 @@ CONFIG_USB_STORAGE=y
 CONFIG_USB_CHIPIDEA=y
 CONFIG_USB_CHIPIDEA_HOST=y
 CONFIG_AB8500_USB=y
-CONFIG_NOP_USB_XCEIV=y
-CONFIG_OMAP_USB2=y
 CONFIG_OMAP_USB3=y
 CONFIG_SAMSUNG_USB2PHY=y
 CONFIG_SAMSUNG_USB3PHY=y
@@ -144,24 +251,32 @@ CONFIG_MMC=y
 CONFIG_MMC_BLOCK_MINORS=16
 CONFIG_MMC_ARMMMCI=y
 CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_SDHCI_ESDHC_IMX=y
 CONFIG_MMC_SDHCI_TEGRA=y
 CONFIG_MMC_SDHCI_SPEAR=y
 CONFIG_MMC_SDHCI_BCM_KONA=y
 CONFIG_MMC_OMAP=y
 CONFIG_MMC_OMAP_HS=y
+CONFIG_MMC_MVSDIO=y
 CONFIG_EDAC=y
 CONFIG_EDAC_MM_EDAC=y
 CONFIG_EDAC_HIGHBANK_MC=y
 CONFIG_EDAC_HIGHBANK_L2=y
 CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_AS3722=y
+CONFIG_RTC_DRV_MAX8907=y
+CONFIG_RTC_DRV_PALMAS=y
 CONFIG_RTC_DRV_TWL4030=y
+CONFIG_RTC_DRV_TPS6586X=y
+CONFIG_RTC_DRV_TPS65910=y
+CONFIG_RTC_DRV_EM3027=y
 CONFIG_RTC_DRV_PL031=y
 CONFIG_RTC_DRV_VT8500=y
+CONFIG_RTC_DRV_MV=y
 CONFIG_RTC_DRV_TEGRA=y
 CONFIG_DMADEVICES=y
 CONFIG_DW_DMAC=y
+CONFIG_MV_XOR=y
 CONFIG_TEGRA20_APB_DMA=y
 CONFIG_STE_DMA40=y
 CONFIG_SIRF_DMA=y
@@ -171,15 +286,34 @@ CONFIG_IMX_SDMA=y
 CONFIG_IMX_DMA=y
 CONFIG_MXS_DMA=y
 CONFIG_DMA_OMAP=y
+CONFIG_STAGING=y
+CONFIG_SENSORS_ISL29018=y
+CONFIG_SENSORS_ISL29028=y
+CONFIG_MFD_NVEC=y
+CONFIG_KEYBOARD_NVEC=y
+CONFIG_SERIO_NVEC_PS2=y
+CONFIG_NVEC_POWER=y
+CONFIG_TEGRA_IOMMU_GART=y
+CONFIG_TEGRA_IOMMU_SMMU=y
+CONFIG_MEMORY=y
+CONFIG_IIO=y
+CONFIG_AK8975=y
 CONFIG_PWM=y
+CONFIG_PWM_TEGRA=y
 CONFIG_PWM_VT8500=y
+CONFIG_OMAP_USB2=y
 CONFIG_EXT4_FS=y
+CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
+CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_SQUASHFS_XZ=y
 CONFIG_NFS_FS=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
 CONFIG_PRINTK_TIME=y
 CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_LOCKUP_DETECTOR=y
+CONFIG_CRYPTO_DEV_TEGRA_AES=y

arch/arm/configs/tegra_defconfig

@@ -29,11 +29,11 @@ CONFIG_ARCH_TEGRA_3x_SOC=y
 CONFIG_ARCH_TEGRA_114_SOC=y
 CONFIG_ARCH_TEGRA_124_SOC=y
 CONFIG_TEGRA_EMC_SCALING_ENABLE=y
+CONFIG_TRUSTED_FOUNDATIONS=y
 CONFIG_PCI=y
 CONFIG_PCI_MSI=y
 CONFIG_PCI_TEGRA=y
 CONFIG_PCIEPORTBUS=y
-CONFIG_TRUSTED_FOUNDATIONS=y
 CONFIG_SMP=y
 CONFIG_PREEMPT=y
 CONFIG_AEABI=y
@@ -125,7 +125,6 @@ CONFIG_SERIAL_TEGRA=y
 CONFIG_SERIAL_OF_PLATFORM=y
 # CONFIG_HW_RANDOM is not set
 # CONFIG_I2C_COMPAT is not set
-CONFIG_I2C_MUX=y
 CONFIG_I2C_MUX_PINCTRL=y
 CONFIG_I2C_TEGRA=y
 CONFIG_SPI=y
@@ -169,9 +168,8 @@ CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_USB_VIDEO_CLASS=m
 CONFIG_DRM=y
-CONFIG_DRM_PANEL=y
-CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_DRM_TEGRA=y
+CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y
 # CONFIG_LCD_CLASS_DEVICE is not set
 CONFIG_BACKLIGHT_CLASS_DEVICE=y
@@ -206,10 +204,7 @@ CONFIG_MMC_BLOCK_MINORS=16
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_SDHCI_TEGRA=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGERS=y
 CONFIG_LEDS_TRIGGER_TIMER=y
 CONFIG_LEDS_TRIGGER_ONESHOT=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
@@ -235,7 +230,6 @@ CONFIG_KEYBOARD_NVEC=y
 CONFIG_SERIO_NVEC_PS2=y
 CONFIG_NVEC_POWER=y
 CONFIG_NVEC_PAZ00=y
-CONFIG_COMMON_CLK_DEBUG=y
 CONFIG_TEGRA_IOMMU_GART=y
 CONFIG_TEGRA_IOMMU_SMMU=y
 CONFIG_MEMORY=y
@@ -265,6 +259,7 @@ CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_PRINTK_TIME=y
 CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_FS=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_SLAB=y
 CONFIG_DEBUG_VM=y

arch/arm/mach-hisi/Kconfig

@@ -12,6 +12,5 @@ config ARCH_HI3xxx
 	select HAVE_SMP
 	select PINCTRL
 	select PINCTRL_SINGLE
-	select SMP
 	help
 	  Support for Hisilicon Hi36xx/Hi37xx processor family

arch/arm/mach-integrator/integrator_cp.c

@@ -64,6 +64,7 @@ static void __iomem *intcp_con_base;
 
 /*
  * Logical      Physical
+ * f1000000	10000000	Core module registers
  * f1300000	13000000	Counter/Timer
  * f1400000	14000000	Interrupt controller
  * f1600000	16000000	UART 0
@@ -75,6 +76,11 @@ static void __iomem *intcp_con_base;
 
 static struct map_desc intcp_io_desc[] __initdata __maybe_unused = {
 	{
+		.virtual	= IO_ADDRESS(INTEGRATOR_HDR_BASE),
+		.pfn		= __phys_to_pfn(INTEGRATOR_HDR_BASE),
+		.length		= SZ_4K,
+		.type		= MT_DEVICE
+	}, {
 		.virtual	= IO_ADDRESS(INTEGRATOR_CT_BASE),
 		.pfn		= __phys_to_pfn(INTEGRATOR_CT_BASE),
 		.length		= SZ_4K,

arch/arm/mach-iop32x/em7210.c

@@ -23,6 +23,7 @@
 #include <linux/mtd/physmap.h>
 #include <linux/platform_device.h>
 #include <linux/i2c.h>
+#include <linux/gpio.h>
 #include <mach/hardware.h>
 #include <linux/io.h>
 #include <linux/irq.h>
@@ -176,11 +177,35 @@ static struct platform_device em7210_serial_device = {
 	.resource	= &em7210_uart_resource,
 };
 
+#define EM7210_HARDWARE_POWER 0
+
 void em7210_power_off(void)
 {
-	*IOP3XX_GPOE &= 0xfe;
-	*IOP3XX_GPOD |= 0x01;
+	int ret;
+
+	ret = gpio_direction_output(EM7210_HARDWARE_POWER, 1);
+	if (ret)
+		pr_crit("could not drive power off GPIO high\n");
+}
+
+static int __init em7210_request_gpios(void)
+{
+	int ret;
+
+	if (!machine_is_em7210())
+		return 0;
+
+	ret = gpio_request(EM7210_HARDWARE_POWER, "power");
+	if (ret) {
+		pr_err("could not request power off GPIO\n");
+		return 0;
+	}
+
+	pm_power_off = em7210_power_off;
+
+	return 0;
 }
+device_initcall(em7210_request_gpios);
 
 static void __init em7210_init_machine(void)
 {
@@ -194,9 +219,6 @@ static void __init em7210_init_machine(void)
 
 	i2c_register_board_info(0, em7210_i2c_devices,
 		ARRAY_SIZE(em7210_i2c_devices));
-
-
-	pm_power_off = em7210_power_off;
 }
 
 MACHINE_START(EM7210, "Lanner EM7210")

arch/arm/mach-keystone/Kconfig

@@ -10,7 +10,6 @@ config ARCH_KEYSTONE
 	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select ARM_ERRATA_798181 if SMP
 	select COMMON_CLK_KEYSTONE
-	select TI_EDMA
 	select ARCH_SUPPORTS_BIG_ENDIAN
 	select ZONE_DMA if ARM_LPAE
 	help

arch/arm/mach-kirkwood/pm.c

@@ -18,6 +18,7 @@
 #include <linux/suspend.h>
 #include <linux/io.h>
 #include <mach/bridge-regs.h>
+#include "common.h"
 
 static void __iomem *ddr_operation_base;
 
@@ -65,9 +66,8 @@ static const struct platform_suspend_ops kirkwood_suspend_ops = {
 	.valid = kirkwood_pm_valid_standby,
 };
 
-int __init kirkwood_pm_init(void)
+void __init kirkwood_pm_init(void)
 {
 	ddr_operation_base = ioremap(DDR_OPERATION_BASE, 4);
 	suspend_set_ops(&kirkwood_suspend_ops);
-	return 0;
 }

arch/arm/mach-mvebu/mvebu-soc-id.c

@@ -88,7 +88,7 @@ static int __init mvebu_soc_id_init(void)
 	}
 
 	pci_base = of_iomap(child, 0);
-	if (IS_ERR(pci_base)) {
+	if (pci_base == NULL) {
 		pr_err("cannot map registers\n");
 		ret = -ENOMEM;
 		goto res_ioremap;

arch/arm/mach-omap2/common.h

@@ -62,11 +62,17 @@ static inline int omap3_pm_init(void)
 
 #if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP4)
 int omap4_pm_init(void);
+int omap4_pm_init_early(void);
 #else
 static inline int omap4_pm_init(void)
 {
 	return 0;
 }
+
+static inline int omap4_pm_init_early(void)
+{
+	return 0;
+}
 #endif
 
 #ifdef CONFIG_OMAP_MUX
@@ -236,6 +242,7 @@ static inline void __iomem *omap4_get_scu_base(void)
 
 extern void __init gic_init_irq(void);
 extern void gic_dist_disable(void);
+extern void gic_dist_enable(void);
 extern bool gic_dist_disabled(void);
 extern void gic_timer_retrigger(void);
 extern void omap_smc1(u32 fn, u32 arg);

arch/arm/mach-omap2/cpuidle44xx.c

@@ -80,6 +80,7 @@ static int omap_enter_idle_coupled(struct cpuidle_device *dev,
 			int index)
 {
 	struct idle_statedata *cx = state_ptr + index;
+	u32 mpuss_can_lose_context = 0;
 
 	/*
 	 * CPU0 has to wait and stay ON until CPU1 is OFF state.
@@ -104,6 +105,9 @@ static int omap_enter_idle_coupled(struct cpuidle_device *dev,
 		}
 	}
 
+	mpuss_can_lose_context = (cx->mpu_state == PWRDM_POWER_RET) &&
+				 (cx->mpu_logic_state == PWRDM_POWER_OFF);
+
 	/*
 	 * Call idle CPU PM enter notifier chain so that
 	 * VFP and per CPU interrupt context is saved.
@@ -118,8 +122,7 @@ static int omap_enter_idle_coupled(struct cpuidle_device *dev,
 		 * Call idle CPU cluster PM enter notifier chain
 		 * to save GIC and wakeupgen context.
 		 */
-		if ((cx->mpu_state == PWRDM_POWER_RET) &&
-			(cx->mpu_logic_state == PWRDM_POWER_OFF))
+		if (mpuss_can_lose_context)
 			cpu_cluster_pm_enter();
 	}
 
@@ -128,9 +131,23 @@ static int omap_enter_idle_coupled(struct cpuidle_device *dev,
 
 	/* Wakeup CPU1 only if it is not offlined */
 	if (dev->cpu == 0 && cpumask_test_cpu(1, cpu_online_mask)) {
+
+		if (IS_PM44XX_ERRATUM(PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD) &&
+		    mpuss_can_lose_context)
+			gic_dist_disable();
+
 		clkdm_wakeup(cpu_clkdm[1]);
 		omap_set_pwrdm_state(cpu_pd[1], PWRDM_POWER_ON);
 		clkdm_allow_idle(cpu_clkdm[1]);
+
+		if (IS_PM44XX_ERRATUM(PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD) &&
+		    mpuss_can_lose_context) {
+			while (gic_dist_disabled()) {
+				udelay(1);
+				cpu_relax();
+			}
+			gic_timer_retrigger();
+		}
 	}
 
 	/*
@@ -143,8 +160,7 @@ static int omap_enter_idle_coupled(struct cpuidle_device *dev,
 	 * Call idle CPU cluster PM exit notifier chain
 	 * to restore GIC and wakeupgen context.
 	 */
-	if (dev->cpu == 0 && (cx->mpu_state == PWRDM_POWER_RET) &&
-		(cx->mpu_logic_state == PWRDM_POWER_OFF))
+	if (dev->cpu == 0 && mpuss_can_lose_context)
 		cpu_cluster_pm_exit();
 
 fail:

arch/arm/mach-omap2/io.c

@@ -641,6 +641,7 @@ void __init omap4430_init_early(void)
 	omap_cm_base_init();
 	omap4xxx_check_revision();
 	omap4xxx_check_features();
+	omap4_pm_init_early();
 	omap44xx_prm_init();
 	omap44xx_voltagedomains_init();
 	omap44xx_powerdomains_init();

arch/arm/mach-omap2/omap-mpuss-lowpower.c

@@ -271,6 +271,9 @@ int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state)
 	else
 		omap_pm_ops.finish_suspend(save_state);
 
+	if (IS_PM44XX_ERRATUM(PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD) && cpu)
+		gic_dist_enable();
+
 	/*
 	 * Restore the CPUx power state to ON otherwise CPUx
 	 * power domain can transitions to programmed low power

arch/arm/mach-omap2/omap-smp.c

@@ -39,8 +39,6 @@
 
 #define OMAP5_CORE_COUNT	0x2
 
-u16 pm44xx_errata;
-
 /* SCU base address */
 static void __iomem *scu_base;
 
@@ -217,10 +215,8 @@ static void __init omap4_smp_prepare_cpus(unsigned int max_cpus)
 	if (scu_base)
 		scu_enable(scu_base);
 
-	if (cpu_is_omap446x()) {
+	if (cpu_is_omap446x())
 		startup_addr = omap4460_secondary_startup;
-		pm44xx_errata |= PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD;
-	}
 
 	/*
 	 * Write the address of secondary startup routine into the

arch/arm/mach-omap2/omap4-common.c

@@ -127,6 +127,12 @@ void gic_dist_disable(void)
 		__raw_writel(0x0, gic_dist_base_addr + GIC_DIST_CTRL);
 }
 
+void gic_dist_enable(void)
+{
+	if (gic_dist_base_addr)
+		__raw_writel(0x1, gic_dist_base_addr + GIC_DIST_CTRL);
+}
+
 bool gic_dist_disabled(void)
 {
 	return !(__raw_readl(gic_dist_base_addr + GIC_DIST_CTRL) & 0x1);

arch/arm/mach-omap2/pm44xx.c

@@ -24,6 +24,8 @@
 #include "powerdomain.h"
 #include "pm.h"
 
+u16 pm44xx_errata;
+
 struct power_state {
 	struct powerdomain *pwrdm;
 	u32 next_state;
@@ -198,6 +200,19 @@ static inline int omap4_init_static_deps(void)
 	return ret;
 }
 
+/**
+ * omap4_pm_init_early - Does early initialization necessary for OMAP4+ devices
+ *
+ * Initializes basic stuff for power management functionality.
+ */
+int __init omap4_pm_init_early(void)
+{
+	if (cpu_is_omap446x())
+		pm44xx_errata |= PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD;
+
+	return 0;
+}
+
 /**
  * omap4_pm_init - Init routine for OMAP4+ devices
  *

arch/arm/plat-orion/irq.c

@@ -15,8 +15,51 @@
 #include <linux/io.h>
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
+#include <asm/exception.h>
 #include <plat/irq.h>
 #include <plat/orion-gpio.h>
+#include <mach/bridge-regs.h>
+
+#ifdef CONFIG_MULTI_IRQ_HANDLER
+/*
+ * Compiling with both non-DT and DT support enabled, will
+ * break asm irq handler used by non-DT boards. Therefore,
+ * we provide a C-style irq handler even for non-DT boards,
+ * if MULTI_IRQ_HANDLER is set.
+ *
+ * Notes:
+ * - this is prepared for Kirkwood and Dove only, update
+ *   accordingly if you add Orion5x or MV78x00.
+ * - Orion5x uses different macro names and has only one
+ *   set of CAUSE/MASK registers.
+ * - MV78x00 uses the same macro names but has a third
+ *   set of CAUSE/MASK registers.
+ *
+ */
+
+static void __iomem *orion_irq_base = IRQ_VIRT_BASE;
+
+asmlinkage void
+__exception_irq_entry orion_legacy_handle_irq(struct pt_regs *regs)
+{
+	u32 stat;
+
+	stat = readl_relaxed(orion_irq_base + IRQ_CAUSE_LOW_OFF);
+	stat &= readl_relaxed(orion_irq_base + IRQ_MASK_LOW_OFF);
+	if (stat) {
+		unsigned int hwirq = __fls(stat);
+		handle_IRQ(hwirq, regs);
+		return;
+	}
+	stat = readl_relaxed(orion_irq_base + IRQ_CAUSE_HIGH_OFF);
+	stat &= readl_relaxed(orion_irq_base + IRQ_MASK_HIGH_OFF);
+	if (stat) {
+		unsigned int hwirq = 32 + __fls(stat);
+		handle_IRQ(hwirq, regs);
+		return;
+	}
+}
+#endif
 
 void __init orion_irq_init(unsigned int irq_start, void __iomem *maskaddr)
 {
@@ -35,6 +78,10 @@ void __init orion_irq_init(unsigned int irq_start, void __iomem *maskaddr)
 	ct->chip.irq_unmask = irq_gc_mask_set_bit;
 	irq_setup_generic_chip(gc, IRQ_MSK(32), IRQ_GC_INIT_MASK_CACHE,
 			       IRQ_NOREQUEST, IRQ_LEVEL | IRQ_NOPROBE);
+
+#ifdef CONFIG_MULTI_IRQ_HANDLER
+	set_handle_irq(orion_legacy_handle_irq);
+#endif
 }
 
 #ifdef CONFIG_OF

drivers/bus/arm-cci.c

@@ -979,7 +979,7 @@ static int cci_probe(void)
 
 	nb_cci_ports = cci_config->nb_ace + cci_config->nb_ace_lite;
 
-	ports = kcalloc(sizeof(*ports), nb_cci_ports, GFP_KERNEL);
+	ports = kcalloc(nb_cci_ports, sizeof(*ports), GFP_KERNEL);
 	if (!ports)
 		return -ENOMEM;
 

drivers/clocksource/bcm_kona_timer.c

@@ -17,6 +17,7 @@
 #include <linux/jiffies.h>
 #include <linux/clockchips.h>
 #include <linux/types.h>
+#include <linux/clk.h>
 
 #include <linux/io.h>
 #include <asm/mach/time.h>
@@ -101,11 +102,18 @@ kona_timer_get_counter(void *timer_base, uint32_t *msw, uint32_t *lsw)
 static void __init kona_timers_init(struct device_node *node)
 {
 	u32 freq;
+	struct clk *external_clk;
 
-	if (!of_property_read_u32(node, "clock-frequency", &freq))
+	external_clk = of_clk_get_by_name(node, NULL);
+
+	if (!IS_ERR(external_clk)) {
+		arch_timer_rate = clk_get_rate(external_clk);
+		clk_prepare_enable(external_clk);
+	} else if (!of_property_read_u32(node, "clock-frequency", &freq)) {
 		arch_timer_rate = freq;
-	else
-		panic("clock-frequency not set in the .dts file");
+	} else {
+		panic("unable to determine clock-frequency");
+	}
 
 	/* Setup IRQ numbers */
 	timers.tmr_irq = irq_of_parse_and_map(node, 0);

drivers/irqchip/irq-armada-370-xp.c

@@ -59,8 +59,6 @@
 #define PCI_MSI_DOORBELL_END                    (32)
 #define PCI_MSI_DOORBELL_MASK                   0xFFFF0000
 
-static DEFINE_RAW_SPINLOCK(irq_controller_lock);
-
 static void __iomem *per_cpu_int_base;
 static void __iomem *main_int_base;
 static struct irq_domain *armada_370_xp_mpic_domain;
@@ -239,6 +237,8 @@ static inline int armada_370_xp_msi_init(struct device_node *node,
 #endif
 
 #ifdef CONFIG_SMP
+static DEFINE_RAW_SPINLOCK(irq_controller_lock);
+
 static int armada_xp_set_affinity(struct irq_data *d,
 				  const struct cpumask *mask_val, bool force)
 {