Merge branch 'net-phy-at803x-Update-delays-for-RGMII-modes'

Vinod Koul says:

====================
net: phy: at803x: Update delays for RGMII modes

Peter[1] reported that patch cd28d1d6: ("net: phy: at803x: Disable
phy delay for RGMII mode") caused regression on am335x-evmsk board.
This board expects the Phy delay to be enabled but specified RGMII mode
which refers to delays being disabled. So fix this by disabling delay only
for RGMII mode and enable for RGMII_ID and RGMII_TXID/RXID modes.

While at it, as pointed by Dave, don't inline the helpers.

[1]: https://www.spinics.net/lists/netdev/msg550749.html

Changes in v4:
 - fix log & comments nbased on Marc's feedback
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/phy/at803x.c

@@ -103,13 +103,25 @@ static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
 	return phy_write(phydev, AT803X_DEBUG_DATA, val);
 }
 
-static inline int at803x_disable_rx_delay(struct phy_device *phydev)
+static int at803x_enable_rx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0,
+				     AT803X_DEBUG_RX_CLK_DLY_EN);
+}
+
+static int at803x_enable_tx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0,
+				     AT803X_DEBUG_TX_CLK_DLY_EN);
+}
+
+static int at803x_disable_rx_delay(struct phy_device *phydev)
 {
 	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0,
 				     AT803X_DEBUG_RX_CLK_DLY_EN, 0);
 }
 
-static inline int at803x_disable_tx_delay(struct phy_device *phydev)
+static int at803x_disable_tx_delay(struct phy_device *phydev)
 {
 	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5,
 				     AT803X_DEBUG_TX_CLK_DLY_EN, 0);
@@ -241,23 +253,42 @@ static int at803x_config_init(struct phy_device *phydev)
 	if (ret < 0)
 		return ret;
 
-	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII) {
+	/* The RX and TX delay default is:
+	 *   after HW reset: RX delay enabled and TX delay disabled
+	 *   after SW reset: RX delay enabled, while TX delay retains the
+	 *   value before reset.
+	 *
+	 * So let's first disable the RX and TX delays in PHY and enable
+	 * them based on the mode selected (this also takes care of RGMII
+	 * mode where we expect delays to be disabled)
+	 */
+
 	ret = at803x_disable_rx_delay(phydev);
 	if (ret < 0)
 		return ret;
-	}
-
-	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII) {
 	ret = at803x_disable_tx_delay(phydev);
 	if (ret < 0)
 		return ret;
+
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+	    phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
+		/* If RGMII_ID or RGMII_RXID are specified enable RX delay,
+		 * otherwise keep it disabled
+		 */
+		ret = at803x_enable_rx_delay(phydev);
+		if (ret < 0)
+			return ret;
 	}
 
-	return 0;
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+	    phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
+		/* If RGMII_ID or RGMII_TXID are specified enable TX delay,
+		 * otherwise keep it disabled
+		 */
+		ret = at803x_enable_tx_delay(phydev);
+	}
+
+	return ret;
 }
 
 static int at803x_ack_interrupt(struct phy_device *phydev)