ARM: 6481/1: Use shared GIC entry macros on OMAP

Common GIC entry macro for omap
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mach-omap2/include/mach/entry-macro.S

@@ -105,6 +105,35 @@ omap_irq_base:	.word	0
 9999:
 		.endm
 
+#ifdef CONFIG_SMP
+		/* We assume that irqstat (the raw value of the IRQ acknowledge
+		 * register) is preserved from the macro above.
+		 * If there is an IPI, we immediately signal end of interrupt
+		 * on the controller, since this requires the original irqstat
+		 * value which we won't easily be able to recreate later.
+		 */
+
+		.macro test_for_ipi, irqnr, irqstat, base, tmp
+		bic	\irqnr, \irqstat, #0x1c00
+		cmp	\irqnr, #16
+		it	cc
+		strcc	\irqstat, [\base, #GIC_CPU_EOI]
+		it	cs
+		cmpcs	\irqnr, \irqnr
+		.endm
+
+		/* As above, this assumes that irqstat and base are preserved */
+
+		.macro test_for_ltirq, irqnr, irqstat, base, tmp
+		bic	\irqnr, \irqstat, #0x1c00
+		mov 	\tmp, #0
+		cmp	\irqnr, #29
+		itt	eq
+		moveq	\tmp, #1
+		streq	\irqstat, [\base, #GIC_CPU_EOI]
+		cmp	\tmp, #0
+		.endm
+#endif	/* CONFIG_SMP */
 
 #else	/* MULTI_OMAP2 */
 
@@ -141,74 +170,15 @@ omap_irq_base:	.word	0
 
 
 #ifdef CONFIG_ARCH_OMAP4
+#include <asm/hardware/entry-macro-gic.S>
 
 		.macro  get_irqnr_preamble, base, tmp
 		ldr     \base, =OMAP4_IRQ_BASE
 		.endm
 
-		/*
-		 * The interrupt numbering scheme is defined in the
-		 * interrupt controller spec.  To wit:
-		 *
-		 * Interrupts 0-15 are IPI
-		 * 16-28 are reserved
-		 * 29-31 are local.  We allow 30 to be used for the watchdog.
-		 * 32-1020 are global
-		 * 1021-1022 are reserved
-		 * 1023 is "spurious" (no interrupt)
-		 *
-		 * For now, we ignore all local interrupts so only return an
-		 * interrupt if it's between 30 and 1020.  The test_for_ipi
-		 * routine below will pick up on IPIs.
-		 * A simple read from the controller will tell us the number
-		 * of the highest priority enabled interrupt.
-		 * We then just need to check whether it is in the
-		 * valid range for an IRQ (30-1020 inclusive).
-		 */
-		.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-		ldr     \irqstat, [\base, #GIC_CPU_INTACK]
-
-		ldr     \tmp, =1021
-
-		bic     \irqnr, \irqstat, #0x1c00
-
-		cmp     \irqnr, #29
-		cmpcc   \irqnr, \irqnr
-		cmpne   \irqnr, \tmp
-		cmpcs   \irqnr, \irqnr
-		.endm
 #endif
-#endif	/* MULTI_OMAP2 */
 
-#ifdef CONFIG_SMP
-		/* We assume that irqstat (the raw value of the IRQ acknowledge
-		 * register) is preserved from the macro above.
-		 * If there is an IPI, we immediately signal end of interrupt
-		 * on the controller, since this requires the original irqstat
-		 * value which we won't easily be able to recreate later.
-		 */
-
-		.macro test_for_ipi, irqnr, irqstat, base, tmp
-		bic	\irqnr, \irqstat, #0x1c00
-		cmp	\irqnr, #16
-		it	cc
-		strcc	\irqstat, [\base, #GIC_CPU_EOI]
-		it	cs
-		cmpcs	\irqnr, \irqnr
-		.endm
-
-		/* As above, this assumes that irqstat and base are preserved */
-
-		.macro test_for_ltirq, irqnr, irqstat, base, tmp
-		bic	\irqnr, \irqstat, #0x1c00
-		mov 	\tmp, #0
-		cmp	\irqnr, #29
-		itt	eq
-		moveq	\tmp, #1
-		streq	\irqstat, [\base, #GIC_CPU_EOI]
-		cmp	\tmp, #0
-		.endm
-#endif	/* CONFIG_SMP */
+#endif	/* MULTI_OMAP2 */
 
 		.macro	irq_prio_table
 		.endm