Skip to content

L
linux
Commit e90937e7 authored by Linus Torvalds's avatar Linus Torvalds
Browse files
Options

Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc 

Pull ARM/arm64 Devicetree updates from Olof Johansson:
 "As usual, device tree updates is the bulk of our material in this
  merge window. This time around, 559 patches affecting both 32- and
  64-bit platforms.

  Changes are too many to list individually, but some of the larger
  ones:

  New platform/SoC support:

   - Automotive:
     + Renesas R-Car D3 (R8A77995)
     + TI DT76x
     + MediaTek mt2712e
   - Communication-oriented:
     + Qualcomm IPQ8074
     + Broadcom Stingray
     + Marvell Armada 8080
   - Set top box:
     + Uniphier PXs3

  Besides some vendor reference boards for the SoC above, there are also
  several new boards/machines:

   - TI AM335x Moxa UC-8100-ME-T open platform
   - TI AM57xx Beaglebone X15 Rev C
   - Microchip/Atmel sama5d27 SoM1 EK
   - Broadcom Raspberry Pi Zero W
   - Gemini-based D-Link DIR-685 router
   - Freescale i.MX6:
     + Toradex Apalis module + Apalis and Ixora carrier boards
     + Engicam GEAM6UL Starter Kit
   - Freescale i.MX53-based Beckhoff CX9020 Embedded PC
   - Mediatek mt7623-based BananaPi R2
   - Several Allwinner-based single-board computers:
  + Cubietruck plus
  + Bananapi M3, M2M and M64
  + NanoPi A64
  + A64-OLinuXino
  + Pine64
   - Rockchip RK3328 Pine64/Rock64 board support
   - Rockchip RK3399 boards:
  + RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
  + Theobroma Systems RK3399-Q7 SoM
   - ZTE ZX296718 PCBOX Board"

* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
  ARM: dts: at91: at91sam9g45: add AC97
  arm64: dts: marvell: mcbin: enable more networking ports
  arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
  arm64: dts: marvell: add TX interrupts for PPv2.2
  arm64: dts: uniphier: add PXs3 SoC support
  ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
  ARM: dts: uniphier: fix size of sdctrl nodes
  ARM: dts: uniphier: add AIDET nodes
  arm64: dts: uniphier: fix size of sdctrl node
  arm64: dts: uniphier: add AIDET nodes
  Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
  arm64: dts: uniphier: add reset controller node of analog amplifier
  arm64: dts: marvell: add Device Tree files for Armada-8KP
  arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
  arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
  dt-bindings: add rk3399-q7 SoM
  ARM: dts: rockchip: enable usb for rv1108-evb
  ARM: dts: rockchip: add usb nodes for rv1108 SoCs
  dt-bindings: update grf-binding for rv1108 SoCs
  ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
  ...
parents ae46654b b884026a
Expand all Show whitespace changes
Inline Side-by-side
Showing with 22381 additions and 2070 deletions
Documentation/devicetree/bindings/arm/amlogic.txt
View file @ e90937e7
Amlogic MesonX device tree bindings
-------------------------------------------
Work in progress statement:
Device tree files and bindings applying to Amlogic SoCs and boards are
considered "unstable". Any Amlogic device tree binding may change at
any time. Be sure to use a device tree binary and a kernel image
generated from the same source tree.
Please refer to Documentation/devicetree/bindings/ABI.txt for a definition of a
stable binding/ABI.
---------------------------------------------------------------
Boards with the Amlogic Meson6 SoC shall have the following properties:
Required root node property:
compatible: "amlogic,meson6"
......
Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
View file @ e90937e7
......@@ -42,6 +42,10 @@ Raspberry Pi Zero
Required root node properties:
compatible = "raspberrypi,model-zero", "brcm,bcm2835";
Raspberry Pi Zero W
Required root node properties:
compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
Generic BCM2835 board
Required root node properties:
compatible = "brcm,bcm2835";
Documentation/devicetree/bindings/arm/bhf.txt 0 → 100644
View file @ e90937e7
Beckhoff Automation Platforms Device Tree Bindings
--------------------------------------------------
CX9020 Embedded PC
Required root node properties:
- compatible = "bhf,cx9020", "fsl,imx53";
Documentation/devicetree/bindings/arm/cpus.txt
View file @ e90937e7
......@@ -200,6 +200,7 @@ described below.
"arm,realview-smp"
"brcm,bcm11351-cpu-method"
"brcm,bcm23550"
"brcm,bcm2836-smp"
"brcm,bcm-nsp-smp"
"brcm,brahma-b15"
"marvell,armada-375-smp"
......
Documentation/devicetree/bindings/arm/marvell/armada-8kp.txt 0 → 100644
View file @ e90937e7
Marvell Armada 8KPlus Platforms Device Tree Bindings
----------------------------------------------------
Boards using a SoC of the Marvell Armada 8KP families must carry
the following root node property:
- compatible, with one of the following values:
- "marvell,armada-8080", "marvell,armada-ap810-octa", "marvell,armada-ap810"
when the SoC being used is the Armada 8080
Example:
compatible = "marvell,armada-8080-db", "marvell,armada-8080",
"marvell,armada-ap810-octa", "marvell,armada-ap810"
Documentation/devicetree/bindings/arm/mediatek.txt
View file @ e90937e7
MediaTek mt65xx, mt67xx & mt81xx Platforms Device Tree Bindings
MediaTek SoC based Platforms Device Tree Bindings
Boards with a MediaTek mt65xx/mt67xx/mt81xx SoC shall have the
following property:
Boards with a MediaTek SoC shall have the following property:
Required root node property:
compatible: Must contain one of
"mediatek,mt2701"
"mediatek,mt2712"
"mediatek,mt6580"
"mediatek,mt6589"
"mediatek,mt6592"
......@@ -14,7 +14,8 @@ compatible: Must contain one of
"mediatek,mt6795"
"mediatek,mt6797"
"mediatek,mt7622"
"mediatek,mt7623"
"mediatek,mt7623" which is referred to MT7623N SoC
"mediatek,mt7623a"
"mediatek,mt8127"
"mediatek,mt8135"
"mediatek,mt8173"
......@@ -25,6 +26,9 @@ Supported boards:
- Evaluation board for MT2701:
Required root node properties:
- compatible = "mediatek,mt2701-evb", "mediatek,mt2701";
- Evaluation board for MT2712:
Required root node properties:
- compatible = "mediatek,mt2712-evb", "mediatek,mt2712";
- Evaluation board for MT6580:
Required root node properties:
- compatible = "mediatek,mt6580-evbp1", "mediatek,mt6580";
......@@ -46,9 +50,11 @@ Supported boards:
- Reference board variant 1 for MT7622:
Required root node properties:
- compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622";
- Evaluation board for MT7623:
- Reference board for MT7623n with NAND:
Required root node properties:
- compatible = "mediatek,mt7623-evb", "mediatek,mt7623";
- compatible = "mediatek,mt7623n-rfb-nand", "mediatek,mt7623";
- Bananapi BPI-R2 board:
- compatible = "bananapi,bpi-r2", "mediatek,mt7623";
- MTK mt8127 tablet moose EVB:
Required root node properties:
- compatible = "mediatek,mt8127-moose", "mediatek,mt8127";
......
Documentation/devicetree/bindings/arm/omap/omap.txt
View file @ e90937e7
......@@ -157,6 +157,9 @@ Boards:
- AM335X phyCORE-AM335x: Development kit
compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx"
- AM335X UC-8100-ME-T: Communication-centric industrial computing platform
compatible = "moxa,uc-8100-me-t", "ti,am33xx";
- OMAP5 EVM : Evaluation Module
compatible = "ti,omap5-evm", "ti,omap5"
......@@ -187,6 +190,9 @@ Boards:
- AM5718 IDK
compatible = "ti,am5718-idk", "ti,am5718", "ti,dra7"
- DRA762 EVM: Software Development Board for DRA762
compatible = "ti,dra76-evm", "ti,dra762", "ti,dra7"
- DRA742 EVM: Software Development Board for DRA742
compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7"
......
Documentation/devicetree/bindings/arm/qcom.txt
View file @ e90937e7
......@@ -25,6 +25,7 @@ The 'SoC' element must be one of the following strings:
msm8994
msm8996
mdm9615
ipq8074
The 'board' element must be one of the following strings:
......@@ -33,6 +34,7 @@ The 'board' element must be one of the following strings:
dragonboard
mtp
sbc
hk01
The 'soc_version' and 'board_version' elements take the form of v<Major>.<Minor>
where the minor number may be omitted when it's zero, i.e. v1.0 is the same
......
Documentation/devicetree/bindings/arm/rockchip.txt
View file @ e90937e7
......@@ -134,6 +134,10 @@ Rockchip platforms device tree bindings
Required root node properties:
- compatible = "phytec,rk3288-pcm-947", "phytec,rk3288-phycore-som", "rockchip,rk3288";
- Pine64 Rock64 board:
Required root node properties:
- compatible = "pine64,rock64", "rockchip,rk3328";
- Rockchip PX3 Evaluation board:
Required root node properties:
- compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188";
......@@ -173,6 +177,14 @@ Rockchip platforms device tree bindings
Required root node properties:
- compatible = "rockchip,rk3399-evb", "rockchip,rk3399";
- Rockchip RK3399 Sapphire Excavator board:
Required root node properties:
- compatible = "rockchip,rk3399-sapphire-excavator", "rockchip,rk3399";
- Theobroma Systems RK3399-Q7 Haikou Baseboard:
Required root node properties:
- compatible = "tsd,rk3399-q7-haikou", "rockchip,rk3399";
- Tronsmart Orion R68 Meta
Required root node properties:
- compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
Documentation/devicetree/bindings/arm/shmobile.txt
View file @ e90937e7
......@@ -39,6 +39,8 @@ SoCs:
compatible = "renesas,r8a7795"
- R-Car M3-W (R8A77960)
compatible = "renesas,r8a7796"
- R-Car D3 (R8A77995)
compatible = "renesas,r8a77995"
Boards:
......@@ -53,6 +55,8 @@ Boards:
compatible = "renesas,blanche", "renesas,r8a7792"
- BOCK-W
compatible = "renesas,bockw", "renesas,r8a7778"
- Draak (RTP0RC77995SEB0010S)
compatible = "renesas,draak", "renesas,r8a77995"
- Genmai (RTK772100BC00000BR)
compatible = "renesas,genmai", "renesas,r7s72100"
- GR-Peach (X28A-M01-E/F)
......@@ -64,6 +68,10 @@ Boards:
compatible = "renesas,h3ulcb", "renesas,r8a7795";
- Henninger
compatible = "renesas,henninger", "renesas,r8a7791"
- iWave Systems RZ/G1E SODIMM SOM Development Platform (iW-RainboW-G22D)
compatible = "iwave,g22d", "iwave,g22m", "renesas,r8a7745"
- iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM)
compatible = "iwave,g22m", "renesas,r8a7745"
- iWave Systems RZ/G1M Qseven Development Platform (iW-RainboW-G20D-Qseven)
compatible = "iwave,g20d", "iwave,g20m", "renesas,r8a7743"
- iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
......
Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt
View file @ e90937e7
......@@ -16,18 +16,25 @@ Required Properties:
mapped region.
- #clock-cells: should be 1.
- #reset-cells: should be 1.
Each clock is assigned an identifier and client nodes can use this identifier
to specify the clock which they consume. All available clocks are defined as
preprocessor macros in the dt-bindings/clock/meson8b-clkc.h header and can be
used in device tree sources.
Similarly a preprocessor macro for each reset line is defined in
dt-bindings/reset/amlogic,meson8b-clkc-reset.h (which can be used from the
device tree sources).
Example: Clock controller node:
clkc: clock-controller@c1104000 {
#clock-cells = <1>;
compatible = "amlogic,meson8b-clkc";
reg = <0xc1108000 0x4>, <0xc1104000 0x460>;
#clock-cells = <1>;
#reset-cells = <1>;
};
......
Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
View file @ e90937e7
......@@ -13,6 +13,7 @@ Required properties:
- compatible : Shall contain one or more of
- "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX
- "renesas,r8a7796-hdmi" for R8A7796 (R-Car M3-W) compatible HDMI TX
- "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 compatible HDMI TX
When compatible with generic versions, nodes must list the SoC-specific
......
Documentation/devicetree/bindings/display/renesas,du.txt
View file @ e90937e7
......@@ -36,8 +36,10 @@ Required Properties:
When supplied they must be named "dclkin.x" with "x" being the input
clock numerical index.
- vsps: A list of phandles to the VSP nodes that handle the memory
interfaces for the DU channels.
- vsps: A list of phandle and channel index tuples to the VSPs that handle
the memory interfaces for the DU channels. The phandle identifies the VSP
instance that serves the DU channel, and the channel index identifies the
LIF instance in that VSP.
Required nodes:
......@@ -59,24 +61,24 @@ corresponding to each DU output.
R8A7796 (M3-W) DPAD HDMI LVDS -
Example: R8A7790 (R-Car H2) DU
Example: R8A7795 (R-Car H3) ES2.0 DU
du: du@feb00000 {
compatible = "renesas,du-r8a7790";
reg = <0 0xfeb00000 0 0x70000>,
<0 0xfeb90000 0 0x1c>,
<0 0xfeb94000 0 0x1c>;
reg-names = "du", "lvds.0", "lvds.1";
interrupt-parent = <&gic>;
interrupts = <0 256 IRQ_TYPE_LEVEL_HIGH>,
<0 268 IRQ_TYPE_LEVEL_HIGH>,
<0 269 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp7_clks R8A7790_CLK_DU0>,
<&mstp7_clks R8A7790_CLK_DU1>,
<&mstp7_clks R8A7790_CLK_DU2>,
<&mstp7_clks R8A7790_CLK_LVDS0>,
<&mstp7_clks R8A7790_CLK_LVDS1>;
clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1";
du: display@feb00000 {
compatible = "renesas,du-r8a7795";
reg = <0 0xfeb00000 0 0x80000>,
<0 0xfeb90000 0 0x14>;
reg-names = "du", "lvds.0";
interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 724>,
<&cpg CPG_MOD 723>,
<&cpg CPG_MOD 722>,
<&cpg CPG_MOD 721>,
<&cpg CPG_MOD 727>;
clock-names = "du.0", "du.1", "du.2", "du.3", "lvds.0";
vsps = <&vspd0 0>, <&vspd1 0>, <&vspd2 0>, <&vspd0 1>;
ports {
#address-cells = <1>;
......@@ -89,12 +91,19 @@ Example: R8A7790 (R-Car H2) DU
};
port@1 {
reg = <1>;
du_out_lvds0: endpoint {
du_out_hdmi0: endpoint {
remote-endpoint = <&dw_hdmi0_in>;
};
};
port@2 {
reg = <2>;
du_out_lvds1: endpoint {
du_out_hdmi1: endpoint {
remote-endpoint = <&dw_hdmi1_in>;
};
};
port@3 {
reg = <3>;
du_out_lvds0: endpoint {
};
};
};
......
Documentation/devicetree/bindings/dma/ti-edma.txt
View file @ e90937e7
......@@ -9,7 +9,12 @@ execute the actual DMA tansfer.
eDMA3 Channel Controller
Required properties:
- compatible: "ti,edma3-tpcc" for the channel controller(s)
--------------------
- compatible: Should be:
- "ti,edma3-tpcc" for the channel controller(s) on OMAP,
AM33xx and AM43xx SoCs.
- "ti,k2g-edma3-tpcc", "ti,edma3-tpcc" for the
channel controller(s) on 66AK2G.
- #dma-cells: Should be set to <2>. The first number is the DMA request
number and the second is the TC the channel is serviced on.
- reg: Memory map of eDMA CC
......@@ -19,8 +24,19 @@ Required properties:
- ti,tptcs: List of TPTCs associated with the eDMA in the following form:
<&tptc_phandle TC_priority_number>. The highest priority is 0.
SoC-specific Required properties:
--------------------------------
The following are mandatory properties for OMAP, AM33xx and AM43xx SoCs only:
- ti,hwmods: Name of the hwmods associated to the eDMA CC.
The following are mandatory properties for 66AK2G SoCs only:
- power-domains:Should contain a phandle to a PM domain provider node
and an args specifier containing the device id
value. This property is as per the binding,
Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
Optional properties:
- ti,hwmods: Name of the hwmods associated to the eDMA CC
-------------------
- ti,edma-memcpy-channels: List of channels allocated to be used for memcpy, iow
these channels will be SW triggered channels. See example.
- ti,edma-reserved-slot-ranges: PaRAM slot ranges which should not be used by
......@@ -31,17 +47,34 @@ Optional properties:
eDMA3 Transfer Controller
Required properties:
- compatible: "ti,edma3-tptc" for the transfer controller(s)
--------------------
- compatible: Should be:
- "ti,edma3-tptc" for the transfer controller(s) on OMAP,
AM33xx and AM43xx SoCs.
- "ti,k2g-edma3-tptc", "ti,edma3-tptc" for the
transfer controller(s) on 66AK2G.
- reg: Memory map of eDMA TC
- interrupts: Interrupt number for TCerrint.
SoC-specific Required properties:
--------------------------------
The following are mandatory properties for OMAP, AM33xx and AM43xx SoCs only:
- ti,hwmods: Name of the hwmods associated to the eDMA TC.
The following are mandatory properties for 66AK2G SoCs only:
- power-domains:Should contain a phandle to a PM domain provider node
and an args specifier containing the device id
value. This property is as per the binding,
Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
Optional properties:
- ti,hwmods: Name of the hwmods associated to the given eDMA TC
-------------------
- interrupt-names: "edma3_tcerrint"
------------------------------------------------------------------------------
Example:
Examples:
1.
edma: edma@49000000 {
compatible = "ti,edma3-tpcc";
ti,hwmods = "tpcc";
......@@ -108,6 +141,58 @@ mcasp0: mcasp@48038000 {
dma-names = "tx", "rx";
};
2.
edma1: edma@02728000 {
compatible = "ti,k2g-edma3-tpcc", "ti,edma3-tpcc";
reg = <0x02728000 0x8000>;
reg-names = "edma3_cc";
interrupts = <GIC_SPI 208 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 219 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 220 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "edma3_ccint", "emda3_mperr",
"edma3_ccerrint";
dma-requests = <64>;
#dma-cells = <2>;
ti,tptcs = <&edma1_tptc0 7>, <&edma1_tptc1 0>;
/*
* memcpy is disabled, can be enabled with:
* ti,edma-memcpy-channels = <12 13 14 15>;
* for example.
*/
power-domains = <&k2g_pds 0x4f>;
};
edma1_tptc0: tptc@027b0000 {
compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc";
reg = <0x027b0000 0x400>;
power-domains = <&k2g_pds 0x4f>;
};
edma1_tptc1: tptc@027b8000 {
compatible = "ti, k2g-edma3-tptc", "ti,edma3-tptc";
reg = <0x027b8000 0x400>;
power-domains = <&k2g_pds 0x4f>;
};
mmc0: mmc@23000000 {
compatible = "ti,k2g-hsmmc", "ti,omap4-hsmmc";
reg = <0x23000000 0x400>;
interrupts = <GIC_SPI 96 IRQ_TYPE_EDGE_RISING>;
dmas = <&edma1 24 0>, <&edma1 25 0>;
dma-names = "tx", "rx";
bus-width = <4>;
ti,needs-special-reset;
no-1-8-v;
max-frequency = <96000000>;
power-domains = <&k2g_pds 0xb>;
clocks = <&k2g_clks 0xb 1>, <&k2g_clks 0xb 2>;
clock-names = "fck", "mmchsdb_fck";
status = "disabled";
};
------------------------------------------------------------------------------
DEPRECATED binding, new DTS files must use the ti,edma3-tpcc/ti,edma3-tptc
binding.
......
Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt
View file @ e90937e7
......@@ -17,6 +17,7 @@ Required properties:
* which must be preceded by one of the following vendor specifics:
+ "amlogic,meson-gxm-mali"
+ "rockchip,rk3288-mali"
+ "rockchip,rk3399-mali"
- reg : Physical base address of the device and length of the register area.
......
Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
View file @ e90937e7
......@@ -17,6 +17,7 @@ Required properties:
"mediatek,mt6582-sysirq", "mediatek,mt6577-sysirq": for MT6582
"mediatek,mt6580-sysirq", "mediatek,mt6577-sysirq": for MT6580
"mediatek,mt6577-sysirq": for MT6577
"mediatek,mt2712-sysirq", "mediatek,mt6577-sysirq": for MT2712
"mediatek,mt2701-sysirq", "mediatek,mt6577-sysirq": for MT2701
- interrupt-controller : Identifies the node as an interrupt controller
- #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt.
......
Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
View file @ e90937e7
* TI Highspeed MMC host controller for OMAP
* TI Highspeed MMC host controller for OMAP and 66AK2G family.
The Highspeed MMC Host Controller on TI OMAP family
The Highspeed MMC Host Controller on TI OMAP and 66AK2G family
provides an interface for MMC, SD, and SDIO types of memory cards.
This file documents differences between the core properties described
by mmc.txt and the properties used by the omap_hsmmc driver.
Required properties:
--------------------
- compatible:
Should be "ti,omap2-hsmmc", for OMAP2 controllers
Should be "ti,omap3-hsmmc", for OMAP3 controllers
Should be "ti,omap3-pre-es3-hsmmc" for OMAP3 controllers pre ES3.0
Should be "ti,omap4-hsmmc", for OMAP4 controllers
Should be "ti,am33xx-hsmmc", for AM335x controllers
- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1
Should be "ti,k2g-hsmmc", "ti,omap4-hsmmc" for 66AK2G controllers.
SoC specific required properties:
---------------------------------
The following are mandatory properties for OMAPs, AM33xx and AM43xx SoCs only:
- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1.
The following are mandatory properties for 66AK2G SoCs only:
- power-domains:Should contain a phandle to a PM domain provider node
and an args specifier containing the MMC device id
value. This property is as per the binding,
Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
- clocks: Must contain an entry for each entry in clock-names. Should
be defined as per the he appropriate clock bindings consumer
usage in Documentation/devicetree/bindings/clock/ti,sci-clk.txt
- clock-names: Shall be "fck" for the functional clock,
and "mmchsdb_fck" for the debounce clock.
Optional properties:
ti,dual-volt: boolean, supports dual voltage cards
<supply-name>-supply: phandle to the regulator device tree node
"supply-name" examples are "vmmc", "vmmc_aux"(deprecated)/"vqmmc" etc
ti,non-removable: non-removable slot (like eMMC)
ti,needs-special-reset: Requires a special softreset sequence
ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed
dmas: List of DMA specifiers with the controller specific format
as described in the generic DMA client binding. A tx and rx
specifier is required.
dma-names: List of DMA request names. These strings correspond
1:1 with the DMA specifiers listed in dmas. The string naming is
to be "rx" and "tx" for RX and TX DMA requests, respectively.
--------------------
- ti,dual-volt: boolean, supports dual voltage cards
- <supply-name>-supply: phandle to the regulator device tree node
"supply-name" examples are "vmmc",
"vmmc_aux"(deprecated)/"vqmmc" etc
- ti,non-removable: non-removable slot (like eMMC)
- ti,needs-special-reset: Requires a special softreset sequence
- ti,needs-special-hs-handling: HSMMC IP needs special setting
for handling High Speed
- dmas: List of DMA specifiers with the controller specific
format as described in the generic DMA client
binding. A tx and rx specifier is required.
- dma-names: List of DMA request names. These strings correspond
1:1 with the DMA specifiers listed in dmas.
The string naming is to be "rx" and "tx" for
RX and TX DMA requests, respectively.
Examples:
......
Documentation/devicetree/bindings/net/can/c_can.txt
View file @ e90937e7
......@@ -11,9 +11,20 @@ Required properties:
- interrupts : property with a value describing the interrupt
number
Optional properties:
The following are mandatory properties for DRA7x, AM33xx and AM43xx SoCs only:
- ti,hwmods : Must be "d_can<n>" or "c_can<n>", n being the
instance number
The following are mandatory properties for Keystone 2 66AK2G SoCs only:
- power-domains : Should contain a phandle to a PM domain provider node
and an args specifier containing the DCAN device id
value. This property is as per the binding,
Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
- clocks : CAN functional clock phandle. This property is as per the
binding,
Documentation/devicetree/bindings/clock/ti,sci-clk.txt
Optional properties:
- syscon-raminit : Handle to system control region that contains the
RAMINIT register, register offset to the RAMINIT
register and the CAN instance number (0 offset).
......
Documentation/devicetree/bindings/net/mediatek-net.txt
View file @ e90937e7
......@@ -20,8 +20,10 @@ Required properties:
"ethif", "esw", "gp0", "gp1", "gp2", "sgmii_tx250m", "sgmii_rx250m",
"sgmii_cdr_ref", "sgmii_cdr_fb", "sgmii_ck", "eth2pll" : For MT7622 SoC
- power-domains: phandle to the power domain that the ethernet is part of
- resets: Should contain a phandle to the ethsys reset signal
- reset-names: Should contain the reset signal name "eth"
- resets: Should contain phandles to the ethsys reset signals
- reset-names: Should contain the names of reset signal listed in the resets
property
These are "fe", "gmac" and "ppe"
- mediatek,ethsys: phandle to the syscon node that handles the port setup
- mediatek,sgmiisys: phandle to the syscon node that handles the SGMII setup
which is required for those SoCs equipped with SGMII such as MT7622 SoC.
......
Documentation/devicetree/bindings/pci/mvebu-pci.txt
View file @ e90937e7
......@@ -276,7 +276,7 @@ pcie-controller {
clocks = <&gateclk 26>;
};
pcie@10,0 {
pcie@a,0 {
device_type = "pci";
assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
reg = <0x5000 0 0 0 0>;
......
Documentation/devicetree/bindings/power/renesas,apmu.txt
View file @ e90937e7
DT bindings for the Renesas Advanced Power Management Unit
Renesas R-Car line of SoCs utilize one or more APMU hardware units
Renesas R-Car and RZ/G1 SoCs utilize one or more APMU hardware units
for CPU core power domain control including SMP boot and CPU Hotplug.
Required properties:
- compatible: Should be "renesas,<soctype>-apmu", "renesas,apmu" as fallback.
Examples with soctypes are:
- "renesas,r8a7743-apmu" (RZ/G1M)
- "renesas,r8a7790-apmu" (R-Car H2)
- "renesas,r8a7791-apmu" (R-Car M2-W)
- "renesas,r8a7792-apmu" (R-Car V2H)
......
Documentation/devicetree/bindings/serial/mtk-uart.txt
View file @ e90937e7
......@@ -3,6 +3,7 @@
Required properties:
- compatible should contain:
* "mediatek,mt2701-uart" for MT2701 compatible UARTS
* "mediatek,mt2712-uart" for MT2712 compatible UARTS
* "mediatek,mt6580-uart" for MT6580 compatible UARTS
* "mediatek,mt6582-uart" for MT6582 compatible UARTS
* "mediatek,mt6589-uart" for MT6589 compatible UARTS
......
Documentation/devicetree/bindings/soc/rockchip/grf.txt
View file @ e90937e7
......@@ -21,6 +21,7 @@ Required Properties:
- "rockchip,rk3328-grf", "syscon": for rk3328
- "rockchip,rk3368-grf", "syscon": for rk3368
- "rockchip,rk3399-grf", "syscon": for rk3399
- "rockchip,rv1108-grf", "syscon": for rv1108
- compatible: PMUGRF should be one of the following:
- "rockchip,rk3368-pmugrf", "syscon": for rk3368
- "rockchip,rk3399-pmugrf", "syscon": for rk3399
......@@ -28,6 +29,8 @@ Required Properties:
- "rockchip,rk3288-sgrf", "syscon": for rk3288
- compatible: USB2PHYGRF should be one of the followings
- "rockchip,rk3328-usb2phy-grf", "syscon": for rk3328
- compatible: USBGRF should be one of the following
- "rockchip,rv1108-usbgrf", "syscon": for rv1108
- reg: physical base address of the controller and length of memory mapped
region.
......
Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
View file @ e90937e7
......@@ -46,12 +46,13 @@ Required Properties:
- power-domains: phandle pointing to the corresponding PM domain node
and an ID representing the device.
See dt-bindings/genpd/k2g.h for the list of valid identifiers for k2g.
See http://processors.wiki.ti.com/index.php/TISCI#66AK2G02_Data for the list
of valid identifiers for k2g.
Example (K2G):
--------------------
uart0: serial@02530c00 {
compatible = "ns16550a";
...
power-domains = <&k2g_pds K2G_DEV_UART0>;
power-domains = <&k2g_pds 0x002c>;
};
Documentation/devicetree/bindings/sram/renesas,smp-sram.txt 0 → 100644
View file @ e90937e7
* Renesas SMP SRAM
Renesas R-Car Gen2 and RZ/G1 SoCs need a small piece of SRAM for the jump stub
for secondary CPU bringup and CPU hotplug.
This memory is reserved by adding a child node to a "mmio-sram" node, cfr.
Documentation/devicetree/bindings/sram/sram.txt.
Required child node properties:
- compatible: Must be "renesas,smp-sram",
- reg: Address and length of the reserved SRAM.
The full physical (bus) address must be aligned to a 256 KiB boundary.
Example:
icram1: sram@e63c0000 {
compatible = "mmio-sram";
reg = <0 0xe63c0000 0 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0 0xe63c0000 0x1000>;
smp-sram@0 {
compatible = "renesas,smp-sram";
reg = <0 0x10>;
};
};
Documentation/devicetree/bindings/vendor-prefixes.txt
View file @ e90937e7
......@@ -48,6 +48,7 @@ avic Shanghai AVIC Optoelectronics Co., Ltd.
axentia Axentia Technologies AB
axis Axis Communications AB
bananapi BIPAI KEJI LIMITED
bhf Beckhoff Automation GmbH & Co. KG
boe BOE Technology Group Co., Ltd.
bosch Bosch Sensortec GmbH
boundary Boundary Devices Inc.
......
Documentation/devicetree/bindings/watchdog/mtk-wdt.txt
View file @ e90937e7
......@@ -3,9 +3,9 @@ Mediatek SoCs Watchdog timer
Required properties:
- compatible should contain:
* "mediatek,mt2701-wdt" for MT2701 compatible watchdog timers
* "mediatek,mt6589-wdt" for all compatible watchdog timers (MT2701,
MT6589)
"mediatek,mt2701-wdt", "mediatek,mt6589-wdt": for MT2701
"mediatek,mt6589-wdt": for MT6589
"mediatek,mt6797-wdt", "mediatek,mt6589-wdt": for MT6797
- reg : Specifies base physical address and size of the registers.
......
arch/arm/boot/dts/Makefile
View file @ e90937e7
......@@ -46,6 +46,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
at91sam9x35ek.dtb
dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2.dtb \
at91-sama5d27_som1_ek.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
at91-tse850-3.dtb \
......@@ -73,7 +74,8 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
bcm2835-rpi-a-plus.dtb \
bcm2836-rpi-2-b.dtb \
bcm2837-rpi-3-b.dtb \
bcm2835-rpi-zero.dtb
bcm2835-rpi-zero.dtb \
bcm2835-rpi-zero-w.dtb
dtb-$(CONFIG_ARCH_BCM_5301X) += \
bcm4708-asus-rt-ac56u.dtb \
bcm4708-asus-rt-ac68u.dtb \
......@@ -106,7 +108,8 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
bcm953012hr.dtb \
bcm953012k.dtb
dtb-$(CONFIG_ARCH_BCM_53573) += \
bcm47189-tenda-ac9.dtb
bcm47189-tenda-ac9.dtb \
bcm947189acdbmr.dtb
dtb-$(CONFIG_ARCH_BCM_63XX) += \
bcm963138dvt.dtb
dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \
......@@ -180,6 +183,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \
exynos5440-ssdk5440.dtb \
exynos5800-peach-pi.dtb
dtb-$(CONFIG_ARCH_GEMINI) += \
gemini-dlink-dir-685.dtb \
gemini-nas4220b.dtb \
gemini-rut1xx.dtb \
gemini-sq201.dtb \
......@@ -340,6 +344,7 @@ dtb-$(CONFIG_SOC_IMX51) += \
imx51-ts4800.dtb
dtb-$(CONFIG_SOC_IMX53) += \
imx53-ard.dtb \
imx53-cx9020.dtb \
imx53-m53evk.dtb \
imx53-mba53.dtb \
imx53-qsb.dtb \
......@@ -391,7 +396,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-udoo.dtb \
imx6dl-wandboard.dtb \
imx6dl-wandboard-revb1.dtb \
imx6q-apalis-eval.dtb \
imx6q-apalis-ixora.dtb \
imx6q-apalis-ixora-v1.1.dtb \
imx6q-apf6dev.dtb \
imx6q-arm2.dtb \
imx6q-b450v3.dtb \
......@@ -466,7 +473,7 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
imx6sx-udoo-neo-full.dtb
dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-14x14-evk.dtb \
imx6ul-geam-kit.dtb \
imx6ul-geam.dtb \
imx6ul-isiot-emmc.dtb \
imx6ul-isiot-nand.dtb \
imx6ul-liteboard.dtb \
......@@ -617,6 +624,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
am335x-evmsk.dtb \
am335x-icev2.dtb \
am335x-lxm.dtb \
am335x-moxa-uc-8100-me-t.dtb \
am335x-nano.dtb \
am335x-pepper.dtb \
am335x-phycore-rdk.dtb \
......@@ -650,6 +658,7 @@ dtb-$(CONFIG_SOC_OMAP5) += \
dtb-$(CONFIG_SOC_DRA7XX) += \
am57xx-beagle-x15.dtb \
am57xx-beagle-x15-revb1.dtb \
am57xx-beagle-x15-revc.dtb \
am57xx-cl-som-am57x.dtb \
am57xx-sbc-am57x.dtb \
am572x-idk.dtb \
......@@ -657,7 +666,8 @@ dtb-$(CONFIG_SOC_DRA7XX) += \
dra7-evm.dtb \
dra72-evm.dtb \
dra72-evm-revc.dtb \
dra71-evm.dtb
dra71-evm.dtb \
dra76-evm.dtb
dtb-$(CONFIG_ARCH_ORION5X) += \
orion5x-kuroboxpro.dtb \
orion5x-lacie-d2-network.dtb \
......@@ -903,6 +913,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a33-q8-tablet.dtb \
sun8i-a33-sinlinx-sina33.dtb \
sun8i-a83t-allwinner-h8homlet-v2.dtb \
sun8i-a83t-bananapi-m3.dtb \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
......@@ -918,6 +929,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-h3-orangepi-pc-plus.dtb \
sun8i-h3-orangepi-plus.dtb \
sun8i-h3-orangepi-plus2e.dtb \
sun8i-r16-bananapi-m2m.dtb \
sun8i-r16-parrot.dtb \
sun8i-v3s-licheepi-zero.dtb \
sun8i-v3s-licheepi-zero-dock.dtb
......@@ -970,7 +982,6 @@ dtb-$(CONFIG_ARCH_UNIPHIER) += \
uniphier-pro4-sanji.dtb \
uniphier-pxs2-gentil.dtb \
uniphier-pxs2-vodka.dtb \
uniphier-sld3-ref.dtb \
uniphier-sld8-ref.dtb
dtb-$(CONFIG_ARCH_VERSATILE) += \
versatile-ab.dtb \
......@@ -1049,7 +1060,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
mt6580-evbp1.dtb \
mt6589-aquaris5.dtb \
mt6592-evb.dtb \
mt7623-evb.dtb \
mt7623n-rfb-nand.dtb \
mt7623n-bananapi-bpi-r2.dtb \
mt8127-moose.dtb \
mt8135-evbp1.dtb
dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb
......
arch/arm/boot/dts/am335x-bone-common.dtsi
View file @ e90937e7
......@@ -319,13 +319,10 @@ &tps {
ti,pmic-shutdown-controller;
charger {
interrupts = <0>, <1>;
interrupt-names = "USB", "AC";
status = "okay";
};
pwrbutton {
interrupts = <2>;
status = "okay";
};
......
arch/arm/boot/dts/am335x-chiliboard.dts
View file @ e90937e7
......@@ -191,13 +191,10 @@ &tps {
interrupts = <7>; /* NNMI */
charger {
interrupts = <0>, <1>;
interrupt-names = "USB", "AC";
status = "okay";
};
pwrbutton {
interrupts = <2>;
status = "okay";
};
};
arch/arm/boot/dts/am335x-evm.dts
View file @ e90937e7
......@@ -531,6 +531,7 @@ nand@0,0 {
interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
<1 IRQ_TYPE_NONE>; /* termcount */
rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
ti,nand-xfer-type = "prefetch-dma";
ti,nand-ecc-opt = "bch8";
ti,elm-id = <&elm>;
nand-bus-width = <8>;
......
arch/arm/boot/dts/am335x-moxa-uc-8100-me-t.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/am437x-gp-evm.dts
View file @ e90937e7
......@@ -149,6 +149,13 @@ sound0_master: simple-audio-card,codec {
system-clock-frequency = <12000000>;
};
};
beeper: beeper {
compatible = "gpio-beeper";
pinctrl-names = "default";
pinctrl-0 = <&beeper_pins>;
gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
};
};
&am43xx_pinmux {
......@@ -510,6 +517,13 @@ AM4372_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
AM4372_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
>;
};
beeper_pins: beeper_pins {
pinctrl-single,pins = <
AM4372_IOPAD(0x9e0, PIN_OUTPUT_PULLUP | MUX_MODE7) /* cam1_field.gpio4_12 */
>;
};
};
&uart0 {
......@@ -842,6 +856,7 @@ nand@0,0 {
interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
<1 IRQ_TYPE_NONE>; /* termcount */
rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
ti,nand-xfer-type = "prefetch-dma";
ti,nand-ecc-opt = "bch16";
ti,elm-id = <&elm>;
nand-bus-width = <8>;
......
arch/arm/boot/dts/am43x-epos-evm.dts
View file @ e90937e7
......@@ -564,6 +564,7 @@ nand@0,0 {
interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
<1 IRQ_TYPE_NONE>; /* termcount */
rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
ti,nand-xfer-type = "prefetch-dma";
ti,nand-ecc-opt = "bch16";
ti,elm-id = <&elm>;
nand-bus-width = <8>;
......
arch/arm/boot/dts/am571x-idk.dts
View file @ e90937e7
......@@ -11,6 +11,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include "am57xx-idk-common.dtsi"
#include "dra72x-mmc-iodelay.dtsi"
/ {
model = "TI AM5718 IDK";
......@@ -64,13 +65,6 @@ mmc0-led {
};
};
&mmc1 {
status = "okay";
vmmc-supply = <&ldo1_reg>;
bus-width = <4>;
cd-gpios = <&gpio6 27 0>; /* gpio 219 */
};
&omap_dwc3_2 {
extcon = <&extcon_usb2>;
};
......@@ -96,3 +90,30 @@ mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
status = "okay";
};
};
&pcie1_rc {
status = "okay";
gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
};
&pcie1_ep {
gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
};
&mmc1 {
pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
pinctrl-0 = <&mmc1_pins_default>;
pinctrl-1 = <&mmc1_pins_hs>;
pinctrl-2 = <&mmc1_pins_sdr12>;
pinctrl-3 = <&mmc1_pins_sdr25>;
pinctrl-4 = <&mmc1_pins_sdr50>;
pinctrl-5 = <&mmc1_pins_ddr50_rev20 &mmc1_iodelay_ddr50_conf>;
pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
};
&mmc2 {
pinctrl-names = "default", "hs", "ddr_1_8v";
pinctrl-0 = <&mmc2_pins_default>;
pinctrl-1 = <&mmc2_pins_hs>;
pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>;
};
arch/arm/boot/dts/am572x-idk.dts
View file @ e90937e7
......@@ -12,6 +12,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include "am57xx-idk-common.dtsi"
#include "dra74x-mmc-iodelay.dtsi"
/ {
model = "TI AM5728 IDK";
......@@ -67,6 +68,24 @@ mmc0-led {
};
};
&mmc1 {
pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
pinctrl-0 = <&mmc1_pins_default>;
pinctrl-1 = <&mmc1_pins_hs>;
pinctrl-2 = <&mmc1_pins_sdr12>;
pinctrl-3 = <&mmc1_pins_sdr25>;
pinctrl-4 = <&mmc1_pins_sdr50>;
pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>;
pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
};
&mmc2 {
pinctrl-names = "default", "hs", "ddr_1_8v";
pinctrl-0 = <&mmc2_pins_default>;
pinctrl-1 = <&mmc2_pins_hs>;
pinctrl-2 = <&mmc2_pins_ddr_rev20>;
};
&omap_dwc3_2 {
extcon = <&extcon_usb2>;
};
......@@ -76,19 +95,16 @@ &extcon_usb2 {
vbus-gpio = <&gpio3 26 GPIO_ACTIVE_HIGH>;
};
&mmc1 {
status = "okay";
vmmc-supply = <&v3_3d>;
vmmc_aux-supply = <&ldo1_reg>;
bus-width = <4>;
cd-gpios = <&gpio6 27 0>; /* gpio 219 */
};
&sn65hvs882 {
load-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
};
&pcie1 {
&pcie1_rc {
status = "okay";
gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
};
&pcie1_ep {
gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
};
......
arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
View file @ e90937e7
......@@ -9,6 +9,7 @@
#include "dra74x.dtsi"
#include "am57xx-commercial-grade.dtsi"
#include "dra74x-mmc-iodelay.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
......@@ -166,34 +167,6 @@ sound0_master: simple-audio-card,codec {
};
};
&dra7_pmx_core {
mmc1_pins_default: mmc1_pins_default {
pinctrl-single,pins = <
DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */
DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
>;
};
mmc2_pins_default: mmc2_pins_default {
pinctrl-single,pins = <
DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
>;
};
};
&i2c1 {
status = "okay";
clock-frequency = <400000>;
......@@ -570,7 +543,12 @@ hdmi_out: endpoint {
};
};
&pcie1 {
&pcie1_rc {
status = "ok";
gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
};
&pcie1_ep {
gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
};
......
arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
View file @ e90937e7
......@@ -19,8 +19,23 @@ &tpd12s015 {
};
&mmc1 {
pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
pinctrl-0 = <&mmc1_pins_default>;
pinctrl-1 = <&mmc1_pins_hs>;
pinctrl-2 = <&mmc1_pins_sdr12>;
pinctrl-3 = <&mmc1_pins_sdr25>;
pinctrl-4 = <&mmc1_pins_sdr50>;
pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev11_conf>;
pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>;
vmmc-supply = <&vdd_3v3>;
vmmc-aux-supply = <&ldo1_reg>;
vqmmc-supply = <&ldo1_reg>;
};
&mmc2 {
pinctrl-names = "default", "hs", "ddr_1_8v";
pinctrl-0 = <&mmc2_pins_default>;
pinctrl-1 = <&mmc2_pins_hs>;
pinctrl-2 = <&mmc2_pins_ddr_3_3v_rev11 &mmc2_iodelay_ddr_3_3v_rev11_conf>;
};
/* errata i880 "Ethernet RGMII2 Limited to 10/100 Mbps" */
......
arch/arm/boot/dts/am57xx-beagle-x15-revc.dts 0 → 100644
View file @ e90937e7
/*
* Copyright (C) 2014-2017 Texas Instruments Incorporated - http://www.ti.com/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include "am57xx-beagle-x15-common.dtsi"
/ {
model = "TI AM5728 BeagleBoard-X15 rev C";
};
&tpd12s015 {
gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>, /* gpio7_10, CT CP HPD */
<&gpio2 30 GPIO_ACTIVE_HIGH>, /* gpio2_30, LS OE */
<&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */
};
&mmc1 {
pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
pinctrl-0 = <&mmc1_pins_default>;
pinctrl-1 = <&mmc1_pins_hs>;
pinctrl-2 = <&mmc1_pins_sdr12>;
pinctrl-3 = <&mmc1_pins_sdr25>;
pinctrl-4 = <&mmc1_pins_sdr50>;
pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>;
pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
vmmc-supply = <&vdd_3v3>;
vqmmc-supply = <&ldo1_reg>;
};
&mmc2 {
pinctrl-names = "default", "hs", "ddr_1_8v";
pinctrl-0 = <&mmc2_pins_default>;
pinctrl-1 = <&mmc2_pins_hs>;
pinctrl-2 = <&mmc2_pins_ddr_rev20>;
};
arch/arm/boot/dts/am57xx-beagle-x15.dts
View file @ e90937e7
......@@ -20,9 +20,20 @@ &tpd12s015 {
};
&mmc1 {
pinctrl-names = "default", "hs";
pinctrl-0 = <&mmc1_pins_default>;
pinctrl-1 = <&mmc1_pins_hs>;
vmmc-supply = <&ldo1_reg>;
};
&mmc2 {
pinctrl-names = "default", "hs", "ddr_1_8v";
pinctrl-0 = <&mmc2_pins_default>;
pinctrl-1 = <&mmc2_pins_hs>;
pinctrl-2 = <&mmc2_pins_ddr_3_3v_rev11 &mmc2_iodelay_ddr_3_3v_rev11_conf>;
};
/* errata i880 "Ethernet RGMII2 Limited to 10/100 Mbps" */
&phy1 {
max-speed = <100>;
......
arch/arm/boot/dts/am57xx-idk-common.dtsi
View file @ e90937e7
......@@ -399,6 +399,14 @@ &usb2 {
dr_mode = "peripheral";
};
&mmc1 {
status = "okay";
vmmc-supply = <&v3_3d>;
vqmmc-supply = <&ldo1_reg>;
bus-width = <4>;
cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
};
&mmc2 {
status = "okay";
vmmc-supply = <&v3_3d>;
......
arch/arm/boot/dts/armada-370.dtsi
View file @ e90937e7
......@@ -72,7 +72,7 @@ bootrom {
reg = <MBUS_ID(0x01, 0xe0) 0 0x100000>;
};
pciec: pcie-controller@82000000 {
pciec: pcie@82000000 {
compatible = "marvell,armada-370-pcie";
status = "disabled";
device_type = "pci";
......@@ -100,6 +100,7 @@ pcie0: pcie@1,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
0x81000000 0 0 0x81000000 0x1 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 58>;
marvell,pcie-port = <0>;
......@@ -117,6 +118,7 @@ pcie2: pcie@2,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
0x81000000 0 0 0x81000000 0x2 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 62>;
marvell,pcie-port = <1>;
......
arch/arm/boot/dts/armada-375.dtsi
View file @ e90937e7
......@@ -582,7 +582,7 @@ coredivclk: corediv-clock@e8250 {
};
};
pciec: pcie-controller@82000000 {
pciec: pcie@82000000 {
compatible = "marvell,armada-370-pcie";
status = "disabled";
device_type = "pci";
......@@ -610,6 +610,7 @@ pcie0: pcie@1,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
0x81000000 0 0 0x81000000 0x1 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
marvell,pcie-port = <0>;
......@@ -627,6 +628,7 @@ pcie1: pcie@2,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
0x81000000 0 0 0x81000000 0x2 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
marvell,pcie-port = <0>;
......
arch/arm/boot/dts/armada-380.dtsi
View file @ e90937e7
......@@ -71,7 +71,7 @@ pinctrl@18000 {
};
};
pcie-controller {
pcie {
compatible = "marvell,armada-370-pcie";
status = "disabled";
device_type = "pci";
......@@ -104,6 +104,7 @@ pcie@1,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
0x81000000 0 0 0x81000000 0x1 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
marvell,pcie-port = <0>;
......@@ -122,6 +123,7 @@ pcie@2,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
0x81000000 0 0 0x81000000 0x2 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
marvell,pcie-port = <1>;
......@@ -140,6 +142,7 @@ pcie@3,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
0x81000000 0 0 0x81000000 0x3 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
marvell,pcie-port = <2>;
......
arch/arm/boot/dts/armada-385-db-ap.dts
View file @ e90937e7
......@@ -209,7 +209,7 @@ bm-bppi {
status = "okay";
};
pcie-controller {
pcie {
status = "okay";
/*
......
arch/arm/boot/dts/armada-385-turris-omnia.dts
View file @ e90937e7
......@@ -96,7 +96,7 @@ usb3@f8000 {
};
};
pcie-controller {
pcie {
status = "okay";
pcie@1,0 {
......
arch/arm/boot/dts/armada-385.dtsi
View file @ e90937e7
......@@ -70,7 +70,7 @@ cpu@1 {
};
soc {
pciec: pcie-controller {
pciec: pcie {
compatible = "marvell,armada-370-pcie";
status = "disabled";
device_type = "pci";
......@@ -109,6 +109,7 @@ pcie1: pcie@1,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
0x81000000 0 0 0x81000000 0x1 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
marvell,pcie-port = <0>;
......@@ -127,6 +128,7 @@ pcie2: pcie@2,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
0x81000000 0 0 0x81000000 0x2 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
marvell,pcie-port = <1>;
......@@ -145,6 +147,7 @@ pcie3: pcie@3,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
0x81000000 0 0 0x81000000 0x3 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
marvell,pcie-port = <2>;
......@@ -166,6 +169,7 @@ pcie4: pcie@4,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
0x81000000 0 0 0x81000000 0x4 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
marvell,pcie-port = <3>;
......
arch/arm/boot/dts/armada-388-clearfog.dts
View file @ e90937e7
......@@ -62,7 +62,7 @@ usb3@f0000 {
};
};
pcie-controller {
pcie {
pcie@3,0 {
/* Port 2, Lane 0. CON2, nearest CPU. */
reset-gpios = <&expander0 2 GPIO_ACTIVE_LOW>;
......
arch/arm/boot/dts/armada-388-clearfog.dtsi
View file @ e90937e7
......@@ -104,7 +104,7 @@ usb3@f8000 {
};
};
pcie-controller {
pcie {
status = "okay";
/*
* The two PCIe units are accessible through
......
arch/arm/boot/dts/armada-388-db.dts
View file @ e90937e7
......@@ -172,7 +172,7 @@ bm-bppi {
status = "okay";
};
pcie-controller {
pcie {
status = "okay";
/*
* The two PCIe units are accessible through
......
arch/arm/boot/dts/armada-388-gp.dts
View file @ e90937e7
......@@ -240,7 +240,7 @@ bm-bppi {
status = "okay";
};
pcie-controller {
pcie {
status = "okay";
/*
* One PCIe units is accessible through
......
arch/arm/boot/dts/armada-388-rd.dts
View file @ e90937e7
......@@ -117,7 +117,7 @@ usb3@f0000 {
};
};
pcie-controller {
pcie {
status = "okay";
/*
* One PCIe units is accessible through
......
arch/arm/boot/dts/armada-38x.dtsi
View file @ e90937e7
......@@ -154,6 +154,13 @@ scu@c000 {
reg = <0xc000 0x58>;
};
timer@c200 {
compatible = "arm,cortex-a9-global-timer";
reg = <0xc200 0x20>;
interrupts = <GIC_PPI 11 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>;
clocks = <&coreclk 2>;
};
timer@c600 {
compatible = "arm,cortex-a9-twd-timer";
reg = <0xc600 0x20>;
......
arch/arm/boot/dts/armada-390-db.dts
View file @ e90937e7
......@@ -123,7 +123,7 @@ usb3@f8000 {
};
};
pcie-controller {
pcie {
status = "okay";
/* CON30 */
......
arch/arm/boot/dts/armada-395-gp.dts
View file @ e90937e7
......@@ -139,7 +139,7 @@ usb3@f0000 {
};
};
pcie-controller {
pcie {
status = "okay";
/*
......
arch/arm/boot/dts/armada-398-db.dts
View file @ e90937e7
......@@ -118,7 +118,7 @@ usb3@f8000 {
};
};
pcie-controller {
pcie {
status = "okay";
pcie@1,0 {
......
arch/arm/boot/dts/armada-39x.dtsi
View file @ e90937e7
......@@ -442,7 +442,7 @@ thermal@e8078 {
};
};
pcie-controller {
pcie {
compatible = "marvell,armada-370-pcie";
status = "disabled";
device_type = "pci";
......@@ -481,6 +481,7 @@ pcie@1,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
0x81000000 0 0 0x81000000 0x1 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
marvell,pcie-port = <0>;
......@@ -499,6 +500,7 @@ pcie@2,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
0x81000000 0 0 0x81000000 0x2 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
marvell,pcie-port = <1>;
......@@ -517,6 +519,7 @@ pcie@3,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
0x81000000 0 0 0x81000000 0x3 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
marvell,pcie-port = <2>;
......@@ -538,6 +541,7 @@ pcie@4,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
0x81000000 0 0 0x81000000 0x4 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
marvell,pcie-port = <3>;
......
arch/arm/boot/dts/armada-xp-98dx3236.dtsi
View file @ e90937e7
......@@ -91,7 +91,7 @@ bootrom {
/*
* 98DX3236 has 1 x1 PCIe unit Gen2.0
*/
pciec: pcie-controller@82000000 {
pciec: pcie@82000000 {
compatible = "marvell,armada-xp-pcie";
status = "disabled";
device_type = "pci";
......@@ -116,6 +116,7 @@ pcie1: pcie@1,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
0x81000000 0 0 0x81000000 0x1 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 58>;
marvell,pcie-port = <0>;
......
arch/arm/boot/dts/armada-xp-db.dts
View file @ e90937e7
......@@ -242,7 +242,7 @@ pcie@9,0 {
/* Port 2, Lane 0 */
status = "okay";
};
pcie@10,0 {
pcie@a,0 {
/* Port 3, Lane 0 */
status = "okay";
};
......
arch/arm/boot/dts/armada-xp-gp.dts
View file @ e90937e7
......@@ -227,7 +227,7 @@ pcie@9,0 {
/* Port 2, Lane 0 */
status = "okay";
};
pcie@10,0 {
pcie@a,0 {
/* Port 3, Lane 0 */
status = "okay";
};
......
arch/arm/boot/dts/armada-xp-mv78230.dtsi
View file @ e90937e7
......@@ -86,7 +86,7 @@ soc {
* configured as x4 or quad x1 lanes. One unit is
* x1 only.
*/
pciec: pcie-controller@82000000 {
pciec: pcie@82000000 {
compatible = "marvell,armada-xp-pcie";
status = "disabled";
device_type = "pci";
......@@ -123,6 +123,7 @@ pcie1: pcie@1,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
0x81000000 0 0 0x81000000 0x1 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 58>;
marvell,pcie-port = <0>;
......@@ -140,6 +141,7 @@ pcie2: pcie@2,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
0x81000000 0 0 0x81000000 0x2 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 59>;
marvell,pcie-port = <0>;
......@@ -157,6 +159,7 @@ pcie3: pcie@3,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
0x81000000 0 0 0x81000000 0x3 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 60>;
marvell,pcie-port = <0>;
......@@ -174,6 +177,7 @@ pcie4: pcie@4,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
0x81000000 0 0 0x81000000 0x4 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 61>;
marvell,pcie-port = <0>;
......@@ -191,6 +195,7 @@ pcie5: pcie@5,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
0x81000000 0 0 0x81000000 0x5 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 62>;
marvell,pcie-port = <1>;
......
arch/arm/boot/dts/armada-xp-mv78260.dtsi
View file @ e90937e7
......@@ -87,7 +87,7 @@ soc {
* configured as x4 or quad x1 lanes. One unit is
* x4 only.
*/
pciec: pcie-controller@82000000 {
pciec: pcie@82000000 {
compatible = "marvell,armada-xp-pcie";
status = "disabled";
device_type = "pci";
......@@ -138,6 +138,7 @@ pcie1: pcie@1,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
0x81000000 0 0 0x81000000 0x1 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 58>;
marvell,pcie-port = <0>;
......@@ -155,6 +156,7 @@ pcie2: pcie@2,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
0x81000000 0 0 0x81000000 0x2 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 59>;
marvell,pcie-port = <0>;
......@@ -172,6 +174,7 @@ pcie3: pcie@3,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
0x81000000 0 0 0x81000000 0x3 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 60>;
marvell,pcie-port = <0>;
......@@ -189,6 +192,7 @@ pcie4: pcie@4,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
0x81000000 0 0 0x81000000 0x4 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 61>;
marvell,pcie-port = <0>;
......@@ -206,6 +210,7 @@ pcie5: pcie@5,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
0x81000000 0 0 0x81000000 0x5 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 62>;
marvell,pcie-port = <1>;
......@@ -223,6 +228,7 @@ pcie6: pcie@6,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
0x81000000 0 0 0x81000000 0x6 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 63>;
marvell,pcie-port = <1>;
......@@ -240,6 +246,7 @@ pcie7: pcie@7,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
0x81000000 0 0 0x81000000 0x7 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 64>;
marvell,pcie-port = <1>;
......@@ -257,6 +264,7 @@ pcie8: pcie@8,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
0x81000000 0 0 0x81000000 0x8 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 65>;
marvell,pcie-port = <1>;
......@@ -274,6 +282,7 @@ pcie9: pcie@9,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
0x81000000 0 0 0x81000000 0x9 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 99>;
marvell,pcie-port = <2>;
......
arch/arm/boot/dts/armada-xp-mv78460.dtsi
View file @ e90937e7
......@@ -104,7 +104,7 @@ soc {
* configured as x4 or quad x1 lanes. Two units are
* x4/x1.
*/
pciec: pcie-controller@82000000 {
pciec: pcie@82000000 {
compatible = "marvell,armada-xp-pcie";
status = "disabled";
device_type = "pci";
......@@ -159,6 +159,7 @@ pcie1: pcie@1,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
0x81000000 0 0 0x81000000 0x1 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 58>;
marvell,pcie-port = <0>;
......@@ -176,6 +177,7 @@ pcie2: pcie@2,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
0x81000000 0 0 0x81000000 0x2 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 59>;
marvell,pcie-port = <0>;
......@@ -193,6 +195,7 @@ pcie3: pcie@3,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
0x81000000 0 0 0x81000000 0x3 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 60>;
marvell,pcie-port = <0>;
......@@ -210,6 +213,7 @@ pcie4: pcie@4,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
0x81000000 0 0 0x81000000 0x4 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 61>;
marvell,pcie-port = <0>;
......@@ -227,6 +231,7 @@ pcie5: pcie@5,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
0x81000000 0 0 0x81000000 0x5 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 62>;
marvell,pcie-port = <1>;
......@@ -244,6 +249,7 @@ pcie6: pcie@6,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
0x81000000 0 0 0x81000000 0x6 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 63>;
marvell,pcie-port = <1>;
......@@ -261,6 +267,7 @@ pcie7: pcie@7,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
0x81000000 0 0 0x81000000 0x7 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 64>;
marvell,pcie-port = <1>;
......@@ -278,6 +285,7 @@ pcie8: pcie@8,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
0x81000000 0 0 0x81000000 0x8 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 65>;
marvell,pcie-port = <1>;
......@@ -295,6 +303,7 @@ pcie9: pcie@9,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
0x81000000 0 0 0x81000000 0x9 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 99>;
marvell,pcie-port = <2>;
......@@ -303,7 +312,7 @@ pcie9: pcie@9,0 {
status = "disabled";
};
pcie10: pcie@10,0 {
pcie10: pcie@a,0 {
device_type = "pci";
assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
reg = <0x5000 0 0 0 0>;
......@@ -312,6 +321,7 @@ pcie10: pcie@10,0 {
#interrupt-cells = <1>;
ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0
0x81000000 0 0 0x81000000 0xa 0 1 0>;
bus-range = <0x00 0xff>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 103>;
marvell,pcie-port = <3>;
......
arch/arm/boot/dts/aspeed-g4.dtsi
View file @ e90937e7
......@@ -26,7 +26,7 @@ ahb {
fmc: flash-controller@1e620000 {
reg = < 0x1e620000 0x94
0x20000000 0x02000000 >;
0x20000000 0x10000000 >;
#address-cells = <1>;
#size-cells = <0>;
compatible = "aspeed,ast2400-fmc";
......@@ -41,7 +41,7 @@ flash@0 {
spi: flash-controller@1e630000 {
reg = < 0x1e630000 0x18
0x30000000 0x02000000 >;
0x30000000 0x10000000 >;
#address-cells = <1>;
#size-cells = <0>;
compatible = "aspeed,ast2400-spi";
......
arch/arm/boot/dts/at91-sama5d27_som1.dtsi 0 → 100644
View file @ e90937e7
/*
* at91-sama5d27_som1.dtsi - Device Tree file for SAMA5D27 SoM1 board
*
* Copyright (c) 2017, Microchip Technology Inc.
* 2017 Cristian Birsan <cristian.birsan@microchip.com>
* 2017 Claudiu Beznea <claudiu.beznea@microchip.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include "sama5d2.dtsi"
#include "sama5d2-pinfunc.h"
/ {
model = "Atmel SAMA5D27 SoM1";
compatible = "atmel,sama5d27-som1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
clocks {
slow_xtal {
clock-frequency = <32768>;
};
main_xtal {
clock-frequency = <24000000>;
};
};
ahb {
apb {
macb0: ethernet@f8008000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb0_default>;
phy-mode = "rmii";
ethernet-phy@1 {
reg = <0x1>;
interrupt-parent = <&pioA>;
interrupts = <PIN_PD31 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb0_phy_irq>;
};
};
pinctrl@fc038000 {
pinctrl_macb0_default: macb0_default {
pinmux = <PIN_PD9__GTXCK>,
<PIN_PD10__GTXEN>,
<PIN_PD11__GRXDV>,
<PIN_PD12__GRXER>,
<PIN_PD13__GRX0>,
<PIN_PD14__GRX1>,
<PIN_PD15__GTX0>,
<PIN_PD16__GTX1>,
<PIN_PD17__GMDC>,
<PIN_PD18__GMDIO>;
bias-disable;
};
pinctrl_macb0_phy_irq: macb0_phy_irq {
pinmux = <PIN_PD31__GPIO>;
bias-disable;
};
};
};
};
};
arch/arm/boot/dts/at91-sama5d27_som1_ek.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/at91-sama5d2_xplained.dts
View file @ e90937e7
......@@ -68,7 +68,7 @@ main_xtal {
ahb {
usb0: gadget@00300000 {
atmel,vbus-gpio = <&pioA 31 GPIO_ACTIVE_HIGH>;
atmel,vbus-gpio = <&pioA PIN_PA31 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usba_vbus>;
status = "okay";
......@@ -76,8 +76,8 @@ usb0: gadget@00300000 {
usb1: ohci@00400000 {
num-ports = <3>;
atmel,vbus-gpio = <0 /* &pioA 41 GPIO_ACTIVE_HIGH */
&pioA 42 GPIO_ACTIVE_HIGH
atmel,vbus-gpio = <0 /* &pioA PIN_PB9 GPIO_ACTIVE_HIGH */
&pioA PIN_PB10 GPIO_ACTIVE_HIGH
0
>;
pinctrl-names = "default";
......@@ -127,7 +127,7 @@ macb0: ethernet@f8008000 {
ethernet-phy@1 {
reg = <0x1>;
interrupt-parent = <&pioA>;
interrupts = <73 IRQ_TYPE_LEVEL_LOW>;
interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;
};
};
......@@ -160,9 +160,9 @@ pmic@5b {
compatible = "active-semi,act8945a";
reg = <0x5b>;
active-semi,vsel-high;
active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>;
active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>;
active-semi,irq_gpios = <&pioA 45 GPIO_ACTIVE_LOW>;
active-semi,chglev-gpios = <&pioA PIN_PA12 GPIO_ACTIVE_HIGH>;
active-semi,lbo-gpios = <&pioA PIN_PC8 GPIO_ACTIVE_LOW>;
active-semi,irq_gpios = <&pioA PIN_PB13 GPIO_ACTIVE_LOW>;
active-semi,input-voltage-threshold-microvolt = <6600>;
active-semi,precondition-timeout = <40>;
active-semi,total-timeout = <3>;
......@@ -355,6 +355,14 @@ pinctrl_charger_lbo: charger_lbo {
bias-pull-up;
};
pinctrl_classd_default: classd_default {
pinmux = <PIN_PB1__CLASSD_R0>,
<PIN_PB2__CLASSD_R1>,
<PIN_PB3__CLASSD_R2>,
<PIN_PB4__CLASSD_R3>;
bias-pull-up;
};
pinctrl_flx0_default: flx0_default {
pinmux = <PIN_PB28__FLEXCOM0_IO0>,
<PIN_PB29__FLEXCOM0_IO1>;
......@@ -488,6 +496,14 @@ pinctrl_usba_vbus: usba_vbus {
};
classd: classd@fc048000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_classd_default>;
atmel,pwm-type = "diff";
atmel,non-overlap-time = <10>;
status = "okay";
};
can1: can@fc050000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1_default>;
......@@ -504,7 +520,7 @@ gpio_keys {
bp1 {
label = "PB_USER";
gpios = <&pioA 41 GPIO_ACTIVE_LOW>;
gpios = <&pioA PIN_PB9 GPIO_ACTIVE_LOW>;
linux,code = <0x104>;
};
};
......@@ -517,17 +533,18 @@ leds {
red {
label = "red";
gpios = <&pioA 38 GPIO_ACTIVE_LOW>;
gpios = <&pioA PIN_PB6 GPIO_ACTIVE_LOW>;
};
green {
label = "green";
gpios = <&pioA 37 GPIO_ACTIVE_LOW>;
gpios = <&pioA PIN_PB5 GPIO_ACTIVE_LOW>;
};
blue {
label = "blue";
gpios = <&pioA 32 GPIO_ACTIVE_LOW>;
gpios = <&pioA PIN_PB0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
};
};
......
arch/arm/boot/dts/at91sam9g45.dtsi
View file @ e90937e7
......@@ -455,6 +455,16 @@ pinctrl@fffff200 {
>;
/* shared pinctrl settings */
ac97 {
pinctrl_ac97: ac97-0 {
atmel,pins =
<AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* AC97RX */
AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* AC97TX */
AT91_PIOD 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* AC97FS */
AT91_PIOD 9 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* AC97CK */
};
};
adc0 {
pinctrl_adc0_adtrg: adc0_adtrg {
atmel,pins = <AT91_PIOD 28 AT91_PERIPH_A AT91_PINCTRL_NONE>;
......@@ -1043,6 +1053,17 @@ ssc1: ssc@fffa0000 {
status = "disabled";
};
ac97: sound@fffac000 {
compatible = "atmel,at91sam9263-ac97c";
reg = <0xfffac000 0x4000>;
interrupts = <24 IRQ_TYPE_LEVEL_HIGH 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ac97>;
clocks = <&ac97_clk>;
clock-names = "ac97_clk";
status = "disabled";
};
adc0: adc@fffb0000 {
#address-cells = <1>;
#size-cells = <0>;
......
arch/arm/boot/dts/at91sam9m10g45ek.dts
View file @ e90937e7
......@@ -166,6 +166,10 @@ usb2: gadget@fff78000 {
status = "okay";
};
ac97: sound@fffac000 {
status = "okay";
};
adc0: adc@fffb0000 {
pinctrl-names = "default";
pinctrl-0 = <
......
arch/arm/boot/dts/bcm-cygnus.dtsi
View file @ e90937e7
......@@ -55,6 +55,11 @@ cpu@0 {
/include/ "bcm-cygnus-clock.dtsi"
pmu {
compatible = "arm,cortex-a9-pmu";
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
};
core {
compatible = "simple-bus";
ranges = <0x00000000 0x19000000 0x1000000>;
......@@ -119,6 +124,21 @@ pinctrl: pinctrl@0301d0c8 {
compatible = "brcm,cygnus-pinmux";
reg = <0x0301d0c8 0x30>,
<0x0301d24c 0x2c>;
spi_0: spi_0 {
function = "spi0";
groups = "spi0_grp";
};
spi_1: spi_1 {
function = "spi1";
groups = "spi1_grp";
};
spi_2: spi_2 {
function = "spi2";
groups = "spi2_grp";
};
};
mailbox: mailbox@03024024 {
......@@ -300,6 +320,23 @@ msi1: msi-controller {
};
};
dma0: dma@18018000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x18018000 0x1000>;
interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&apb_clk>;
clock-names = "apb_pclk";
#dma-cells = <1>;
};
uart0: serial@18020000 {
compatible = "snps,dw-apb-uart";
reg = <0x18020000 0x100>;
......@@ -324,7 +361,7 @@ uart1: serial@18021000 {
uart2: serial@18022000 {
compatible = "snps,dw-apb-uart";
reg = <0x18020000 0x100>;
reg = <0x18022000 0x100>;
reg-shift = <2>;
reg-io-width = <4>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
......@@ -344,6 +381,52 @@ uart3: serial@18023000 {
status = "disabled";
};
spi0: spi@18028000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0x18028000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-0 = <&spi_0>;
clocks = <&axi81_clk>;
clock-names = "apb_pclk";
status = "disabled";
};
spi1: spi@18029000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0x18029000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-0 = <&spi_1>;
clocks = <&axi81_clk>;
clock-names = "apb_pclk";
status = "disabled";
};
spi2: spi@1802a000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0x1802a000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-0 = <&spi_2>;
clocks = <&axi81_clk>;
clock-names = "apb_pclk";
status = "disabled";
};
sdhci0: sdhci@18041000 {
compatible = "brcm,sdhci-iproc-cygnus";
reg = <0x18041000 0x100>;
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&lcpll0 BCM_CYGNUS_LCPLL0_SDIO_CLK>;
bus-width = <4>;
sdhci,auto-cmd12;
status = "disabled";
};
eth0: ethernet@18042000 {
compatible = "brcm,amac";
reg = <0x18042000 0x1000>,
......@@ -353,6 +436,16 @@ eth0: ethernet@18042000 {
status = "disabled";
};
sdhci1: sdhci@18043000 {
compatible = "brcm,sdhci-iproc-cygnus";
reg = <0x18043000 0x100>;
interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&lcpll0 BCM_CYGNUS_LCPLL0_SDIO_CLK>;
bus-width = <4>;
sdhci,auto-cmd12;
status = "disabled";
};
nand: nand@18046000 {
compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
reg = <0x18046000 0x600>, <0xf8105408 0x600>,
......@@ -366,6 +459,33 @@ nand: nand@18046000 {
brcm,nand-has-wp;
};
ehci0: usb@18048000 {
compatible = "generic-ehci";
reg = <0x18048000 0x100>;
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
ohci0: usb@18048800 {
compatible = "generic-ohci";
reg = <0x18048800 0x100>;
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
v3d: v3d@180a2000 {
compatible = "brcm,cygnus-v3d";
reg = <0x180a2000 0x1000>;
clocks = <&mipipll BCM_CYGNUS_MIPIPLL_CH2_V3D>;
clock-names = "v3d_clk";
interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
vc4: gpu {
compatible = "brcm,cygnus-vc4";
};
gpio_asiu: gpio@180a5000 {
compatible = "brcm,cygnus-asiu-gpio";
reg = <0x180a5000 0x668>;
......@@ -444,19 +564,6 @@ touchscreen: touchscreen@180a6000 {
status = "disabled";
};
v3d: v3d@180a2000 {
compatible = "brcm,cygnus-v3d";
reg = <0x180a2000 0x1000>;
clocks = <&mipipll BCM_CYGNUS_MIPIPLL_CH2_V3D>;
clock-names = "v3d_clk";
interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
vc4: gpu {
compatible = "brcm,cygnus-vc4";
};
adc: adc@180a6000 {
compatible = "brcm,iproc-static-adc";
#io-channel-cells = <1>;
......@@ -467,5 +574,19 @@ adc: adc@180a6000 {
interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
keypad: keypad@180ac000 {
compatible = "brcm,bcm-keypad";
reg = <0x180ac000 0x14c>;
interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&asiu_clks BCM_CYGNUS_ASIU_KEYPAD_CLK>;
clock-names = "peri_clk";
clock-frequency = <31250>;
pull-up-enabled;
col-debounce-filter-period = <0>;
status-debounce-filter-period = <0>;
row-output-enabled;
status = "disabled";
};
};
};
arch/arm/boot/dts/bcm-nsp.dtsi
View file @ e90937e7
......@@ -215,6 +215,7 @@ sdio: sdhci@21000 {
interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
sdhci,auto-cmd12;
clocks = <&lcpll0 BCM_NSP_LCPLL0_SDIO_CLK>;
dma-coherent;
status = "disabled";
};
......@@ -224,6 +225,7 @@ amac0: ethernet@22000 {
<0x110000 0x1000>;
reg-names = "amac_base", "idm_base";
interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
dma-coherent;
status = "disabled";
};
......@@ -233,6 +235,7 @@ amac1: ethernet@23000 {
<0x111000 0x1000>;
reg-names = "amac_base", "idm_base";
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
dma-coherent;
status = "disabled";
};
......@@ -242,6 +245,7 @@ amac2: ethernet@24000 {
<0x112000 0x1000>;
reg-names = "amac_base", "idm_base";
interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
dma-coherent;
status = "disabled";
};
......@@ -252,6 +256,7 @@ mailbox: mailbox@25000 {
#mbox-cells = <1>;
brcm,rx-status-len = <32>;
brcm,use-bcm-hdr;
dma-coherent;
};
nand: nand@26000 {
......@@ -297,6 +302,32 @@ qspi: qspi@27200 {
#size-cells = <0>;
};
xhci: usb@29000 {
compatible = "generic-xhci";
reg = <0x29000 0x1000>;
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
phys = <&usb3_phy>;
phy-names = "usb3-phy";
dma-coherent;
status = "disabled";
};
ehci0: usb@2a000 {
compatible = "generic-ehci";
reg = <0x2a000 0x100>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
dma-coherent;
status = "disabled";
};
ohci0: usb@2b000 {
compatible = "generic-ohci";
reg = <0x2b000 0x100>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
dma-coherent;
status = "disabled";
};
crypto@2f000 {
compatible = "brcm,spum-nsp-crypto";
reg = <0x2f000 0x900>;
......@@ -321,20 +352,6 @@ pwm: pwm@31000 {
status = "disabled";
};
ehci0: usb@2a000 {
compatible = "generic-ehci";
reg = <0x2a000 0x100>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
ohci0: usb@2b000 {
compatible = "generic-ohci";
reg = <0x2b000 0x100>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
rng: rng@33000 {
compatible = "brcm,bcm-nsp-rng";
reg = <0x33000 0x14>;
......@@ -376,6 +393,7 @@ i2c0: i2c@38000 {
#size-cells = <0>;
interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>;
clock-frequency = <100000>;
dma-coherent;
status = "disabled";
};
......@@ -446,6 +464,7 @@ sata: ahci@41000 {
interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
dma-coherent;
status = "disabled";
sata0: sata-port@0 {
......@@ -460,6 +479,15 @@ sata1: sata-port@1 {
phy-names = "sata-phy";
};
};
usb3_phy: usb3-phy@104000 {
compatible = "brcm,ns-bx-usb3-phy";
reg = <0x104000 0x1000>,
<0x032000 0x1000>;
reg-names = "dmp", "ccb-mii";
#phy-cells = <0>;
status = "disabled";
};
};
pcie0: pcie@18012000 {
......@@ -483,6 +511,7 @@ pcie0: pcie@18012000 {
*/
ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>;
dma-coherent;
status = "disabled";
msi-parent = <&msi0>;
......@@ -519,6 +548,7 @@ pcie1: pcie@18013000 {
*/
ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>;
dma-coherent;
status = "disabled";
msi-parent = <&msi1>;
......@@ -555,6 +585,7 @@ pcie2: pcie@18014000 {
*/
ranges = <0x82000000 0 0x48000000 0x48000000 0 0x8000000>;
dma-coherent;
status = "disabled";
msi-parent = <&msi2>;
......
arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
View file @ e90937e7
......@@ -99,3 +99,9 @@ i2s_alt0: i2s_alt0 {
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
status = "okay";
};
arch/arm/boot/dts/bcm2835-rpi-a.dts
View file @ e90937e7
......@@ -94,3 +94,9 @@ i2s_alt2: i2s_alt2 {
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
status = "okay";
};
arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
View file @ e90937e7
......@@ -101,3 +101,9 @@ i2s_alt0: i2s_alt0 {
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
status = "okay";
};
arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
View file @ e90937e7
......@@ -94,3 +94,9 @@ i2s_alt2: i2s_alt2 {
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
status = "okay";
};
arch/arm/boot/dts/bcm2835-rpi-b.dts
View file @ e90937e7
......@@ -89,3 +89,9 @@ &gpio {
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
status = "okay";
};
arch/arm/boot/dts/bcm2835-rpi-zero-w.dts 0 → 100644
View file @ e90937e7
/*
* Copyright (C) 2017 Stefan Wahren <stefan.wahren@i2se.com>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
model = "Raspberry Pi Zero W";
/* Needed by firmware to properly init UARTs */
aliases {
uart0 = "/soc/serial@7e201000";
uart1 = "/soc/serial@7e215040";
serial0 = "/soc/serial@7e201000";
serial1 = "/soc/serial@7e215040";
};
leds {
act {
gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
};
};
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
pinctrl-names = "default";
pinctrl-0 = <&wl_on>;
reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
};
};
&gpio {
/*
* This is based on the official GPU firmware DT blob.
*
* Legend:
* "NC" = not connected (no rail from the SoC)
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
gpio-line-names = "GPIO0",
"GPIO1",
"SDA1",
"SCL1",
"GPIO_GCLK",
"GPIO5",
"GPIO6",
"SPI_CE1_N",
"SPI_CE0_N",
"SPI_MISO",
"SPI_MOSI",
"SPI_SCLK",
"GPIO12",
"GPIO13",
/* Serial port */
"TXD0",
"RXD0",
"GPIO16",
"GPIO17",
"GPIO18",
"GPIO19",
"GPIO20",
"GPIO21",
"GPIO22",
"GPIO23",
"GPIO24",
"GPIO25",
"GPIO26",
"GPIO27",
"SDA0",
"SCL0",
"NC", /* GPIO30 */
"NC", /* GPIO31 */
"NC", /* GPIO32 */
"NC", /* GPIO33 */
"NC", /* GPIO34 */
"NC", /* GPIO35 */
"NC", /* GPIO36 */
"NC", /* GPIO37 */
"NC", /* GPIO38 */
"NC", /* GPIO39 */
"CAM_GPIO1", /* GPIO40 */
"WL_ON", /* GPIO41 */
"NC", /* GPIO42 */
"WIFI_CLK", /* GPIO43 */
"CAM_GPIO0", /* GPIO44 */
"BT_ON", /* GPIO45 */
"HDMI_HPD_N",
"STATUS_LED_N",
/* Used by SD Card */
"SD_CLK_R",
"SD_CMD_R",
"SD_DATA0_R",
"SD_DATA1_R",
"SD_DATA2_R",
"SD_DATA3_R";
pinctrl-0 = <&gpioout &alt0>;
wl_on: wl-on {
brcm,pins = <41>;
brcm,function = <BCM2835_FSEL_GPIO_OUT>;
};
};
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
&sdhci {
#address-cells = <1>;
#size-cells = <0>;
pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
mmc-pwrseq = <&wifi_pwrseq>;
non-removable;
status = "okay";
brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
status = "okay";
};
arch/arm/boot/dts/bcm2835-rpi-zero.dts
View file @ e90937e7
......@@ -103,3 +103,9 @@ i2s_alt0: i2s_alt0 {
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
status = "okay";
};
arch/arm/boot/dts/bcm2835-rpi.dtsi
View file @ e90937e7
......@@ -39,7 +39,7 @@ gpioout: gpioout {
};
alt0: alt0 {
brcm,pins = <4 5 7 8 9 10 11 14 15>;
brcm,pins = <4 5 7 8 9 10 11>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
};
......
arch/arm/boot/dts/bcm2836-rpi-2-b.dts
View file @ e90937e7
......@@ -39,3 +39,9 @@ i2s_alt0: i2s_alt0 {
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
status = "okay";
};
arch/arm/boot/dts/bcm2836.dtsi
View file @ e90937e7
......@@ -36,6 +36,7 @@ timer {
cpus: cpus {
#address-cells = <1>;
#size-cells = <0>;
enable-method = "brcm,bcm2836-smp";
v7_cpu0: cpu@0 {
device_type = "cpu";
......
arch/arm/boot/dts/bcm2837-rpi-3-b.dts
View file @ e90937e7
#include "arm64/broadcom/bcm2837-rpi-3-b.dts"
/dts-v1/;
#include "bcm2837.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-smsc9514.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
model = "Raspberry Pi 3 Model B";
memory {
reg = <0 0x40000000>;
};
leds {
act {
gpios = <&gpio 47 0>;
};
};
};
/* uart0 communicates with the BT module */
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
status = "okay";
};
/* uart1 is mapped to the pin header */
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_gpio14>;
status = "okay";
};
/* SDHCI is used to control the SDIO for wireless */
&sdhci {
pinctrl-names = "default";
pinctrl-0 = <&emmc_gpio34>;
status = "okay";
bus-width = <4>;
non-removable;
};
/* SDHOST is used to drive the SD card */
&sdhost {
pinctrl-names = "default";
pinctrl-0 = <&sdhost_gpio48>;
status = "okay";
bus-width = <4>;
};
arch/arm64/boot/dts/broadcom/bcm2837.dtsi → arch/arm/boot/dts/bcm2837.dtsi
View file @ e90937e7
......@@ -30,6 +30,7 @@ timer {
cpus: cpus {
#address-cells = <1>;
#size-cells = <0>;
enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
cpu0: cpu@0 {
device_type = "cpu";
......
arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
View file @ e90937e7
......@@ -52,6 +52,10 @@ leds {
usb {
label = "bcm53xx:blue:usb";
gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
trigger-sources = <&ohci_port1>, <&ehci_port1>,
<&xhci_port1>, <&ohci_port2>,
<&ehci_port2>;
linux,default-trigger = "usbport";
};
power0 {
......
arch/arm/boot/dts/bcm4708-netgear-r6250.dts
View file @ e90937e7
......@@ -48,6 +48,9 @@ power1 {
usb {
label = "bcm53xx:blue:usb";
gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
trigger-sources = <&ohci_port1>, <&ehci_port1>,
<&xhci_port1>;
linux,default-trigger = "usbport";
};
wireless {
......
arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
View file @ e90937e7
......@@ -42,16 +42,22 @@ power-amber {
usb2 {
label = "bcm53xx:white:usb2";
gpios = <&chipcommon 3 GPIO_ACTIVE_HIGH>;
trigger-sources = <&ohci_port2>, <&ehci_port2>;
linux,default-trigger = "usbport";
};
usb3-white {
label = "bcm53xx:white:usb3";
gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
trigger-sources = <&xhci_port1>;
linux,default-trigger = "usbport";
};
usb3-green {
label = "bcm53xx:green:usb3";
gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
trigger-sources = <&ohci_port1>, <&ehci_port1>;
linux,default-trigger = "usbport";
};
wps {
......
arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
View file @ e90937e7
......@@ -36,6 +36,8 @@ lan {
usb2-port1 {
label = "bcm53xx:green:usb2-port1";
gpios = <&chipcommon 2 GPIO_ACTIVE_HIGH>;
trigger-sources = <&ohci_port1>, <&ehci_port1>;
linux,default-trigger = "usbport";
};
power {
......@@ -67,6 +69,8 @@ wan-amber {
usb2-port2 {
label = "bcm53xx:green:usb2-port2";
gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
trigger-sources = <&ohci_port2>, <&ehci_port2>;
linux,default-trigger = "usbport";
};
};
......
arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
View file @ e90937e7
......@@ -46,11 +46,16 @@ wps {
usb3 {
label = "bcm53xx:blue:usb3";
gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
trigger-sources = <&ohci_port1>, <&ehci_port1>,
<&xhci_port1>;
linux,default-trigger = "usbport";
};
usb2 {
label = "bcm53xx:blue:usb2";
gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
trigger-sources = <&ohci_port2>, <&ehci_port2>;
linux,default-trigger = "usbport";
};
wan-blue {
......
arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
View file @ e90937e7
......@@ -71,6 +71,9 @@ wan-amber {
usb3-white {
label = "bcm53xx:white:usb3";
gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
trigger-sources = <&ohci_port1>, <&ehci_port1>,
<&xhci_port1>;
linux,default-trigger = "usbport";
};
2ghz {
......
arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts
View file @ e90937e7
......@@ -59,6 +59,9 @@ lan2 {
usb3 {
label = "bcm53xx:green:usb3";
gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
trigger-sources = <&ohci_port1>, <&ehci_port1>,
<&xhci_port1>;
linux,default-trigger = "usbport";
};
status {
......
arch/arm/boot/dts/bcm47189-tenda-ac9.dts
View file @ e90937e7
......@@ -26,6 +26,8 @@ leds {
usb {
label = "bcm53xx:blue:usb";
gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
trigger-sources = <&ohci_port1>, <&ehci_port1>;
linux,default-trigger = "usbport";
};
wps {
......
arch/arm/boot/dts/bcm5301x.dtsi
View file @ e90937e7
......@@ -272,6 +272,19 @@ ehci: ehci@21000 {
reg = <0x00021000 0x1000>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
phys = <&usb2_phy>;
#address-cells = <1>;
#size-cells = <0>;
ehci_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
ehci_port2: port@2 {
reg = <2>;
#trigger-source-cells = <0>;
};
};
ohci: ohci@22000 {
......@@ -280,6 +293,19 @@ ohci: ohci@22000 {
compatible = "generic-ohci";
reg = <0x00022000 0x1000>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
ohci_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
ohci_port2: port@2 {
reg = <2>;
#trigger-source-cells = <0>;
};
};
};
......@@ -300,6 +326,14 @@ xhci: xhci@23000 {
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
phys = <&usb3_phy>;
phy-names = "usb";
#address-cells = <1>;
#size-cells = <0>;
xhci_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
};
};
......
arch/arm/boot/dts/bcm53573.dtsi
View file @ e90937e7
......@@ -138,10 +138,12 @@ ehci: ehci@4000 {
ehci_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
ehci_port2: port@2 {
reg = <2>;
#trigger-source-cells = <0>;
};
};
......@@ -158,10 +160,12 @@ ohci: ohci@d000 {
ohci_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
ohci_port2: port@2 {
reg = <2>;
#trigger-source-cells = <0>;
};
};
};
......
arch/arm/boot/dts/bcm911360_entphn.dts
View file @ e90937e7
......@@ -39,9 +39,12 @@ / {
model = "Cygnus Enterprise Phone (BCM911360_ENTPHN)";
compatible = "brcm,bcm11360", "brcm,cygnus";
aliases {
serial0 = &uart3;
};
chosen {
stdout-path = &uart3;
bootargs = "console=ttyS0,115200";
stdout-path = "serial0:115200n8";
};
gpio_keys {
......
arch/arm/boot/dts/bcm947189acdbmr.dts 0 → 100644
View file @ e90937e7
/*
* Copyright (C) 2017 Broadcom
* Author: Florian Fainelli <f.fainelli@gmail.com>
*
* Licensed under the ISC license.
*/
/dts-v1/;
#include "bcm53573.dtsi"
/ {
compatible = "brcm,bcm947189acdbmr", "brcm,bcm47189", "brcm,bcm53573";
model = "Broadcom BCM947189ACDBMR";
chosen {
bootargs = "console=ttyS0,115200 earlycon";
};
memory {
reg = <0x00000000 0x08000000>;
};
leds {
compatible = "gpio-leds";
wps {
label = "bcm53xx:blue:wps";
gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
};
5ghz {
label = "bcm53xx:blue:5ghz";
gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
};
2ghz {
label = "bcm53xx:blue:2ghz";
gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
};
};
gpio-keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
restart {
label = "Reset";
linux,code = <KEY_RESTART>;
gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
};
wps {
label = "WPS";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
};
};
spi {
compatible = "spi-gpio";
num-chipselects = <1>;
gpio-sck = <&chipcommon 21 0>;
gpio-miso = <&chipcommon 22 0>;
gpio-mosi = <&chipcommon 23 0>;
cs-gpios = <&chipcommon 24 0>;
#address-cells = <1>;
#size-cells = <0>;
/* External BCM6802 MoCA chip is connected */
};
};
&pcie0 {
ranges = <0x00000000 0 0 0 0 0x00100000>;
#address-cells = <3>;
#size-cells = <2>;
bridge@0,0,0 {
reg = <0x0000 0 0 0 0>;
ranges = <0x00000000 0 0 0 0 0 0 0x00100000>;
#address-cells = <3>;
#size-cells = <2>;
wifi@0,1,0 {
reg = <0x0000 0 0 0 0>;
ranges = <0x00000000 0 0 0 0x00100000>;
#address-cells = <1>;
#size-cells = <1>;
};
};
};
&usb2 {
vcc-gpio = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
};
arch/arm/boot/dts/bcm958522er.dts
View file @ e90937e7
......@@ -170,3 +170,11 @@ partition@700000 {
&uart0 {
status = "okay";
};
&usb3_phy {
status = "okay";
};
&xhci {
status = "okay";
};
arch/arm/boot/dts/bcm958525er.dts
View file @ e90937e7
......@@ -182,3 +182,11 @@ &sata {
&uart0 {
status = "okay";
};
&usb3_phy {
status = "okay";
};
&xhci {
status = "okay";
};
arch/arm/boot/dts/bcm958525xmc.dts
View file @ e90937e7
......@@ -202,3 +202,11 @@ &sdio {
&uart0 {
status = "okay";
};
&usb3_phy {
status = "okay";
};
&xhci {
status = "okay";
};
arch/arm/boot/dts/bcm958622hr.dts
View file @ e90937e7
......@@ -219,3 +219,11 @@ fixed-link {
&uart0 {
status = "okay";
};
&usb3_phy {
status = "okay";
};
&xhci {
status = "okay";
};
arch/arm/boot/dts/bcm958623hr.dts
View file @ e90937e7
......@@ -227,3 +227,11 @@ fixed-link {
&uart0 {
status = "okay";
};
&usb3_phy {
status = "okay";
};
&xhci {
status = "okay";
};
arch/arm/boot/dts/bcm958625hr.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/bcm958625k.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/da850-lego-ev3.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dove-d3plug.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dove.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dra7-evm-common.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dra7-evm.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dra7.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dra71-evm.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dra72-evm-common.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dra72-evm-revc.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dra72-evm-tps65917.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dra72-evm.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dra76-evm.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/dra76x.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos3250-artik5.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos3250-monk.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos3250-rinato.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos4210-trats.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos4412-origen.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos4412-trats2.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos5250-arndale.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos5250-smdk5250.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos5250-spring.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos5260-xyref5260.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos5410-smdk5410.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos5420-peach-pit.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos5440.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/exynos5800-peach-pi.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/gemini-dlink-dir-685.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/gemini-nas4220b.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/gemini-rut1xx.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/gemini-sq201.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/gemini-wbd111.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/gemini-wbd222.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/gemini.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx25.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx53-cx9020.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx53-pinfunc.h
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx53.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6dl-gw52xx.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6dl-gw53xx.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6dl-gw54xx.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6dl-riotboard.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6q-apalis-eval.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6q-apalis-ixora.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6q-b850v3.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6q-bx50v3.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6q-gw52xx.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6q-gw53xx.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6q-gw54xx.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6qdl-apalis.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6qdl-gw553x.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6qdl.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6sl.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6sx.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6ul-14x14-evk.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6ul-isiot-emmc.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6ul-isiot-nand.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6ul-isiot.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6ul-liteboard.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx6ul.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx7-colibri.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx7d-sdb.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/imx7s.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/keystone-k2e-evm.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/keystone-k2e.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/keystone-k2g-evm.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/keystone-k2g-ice.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/keystone-k2g.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/keystone-k2hk-evm.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/keystone-k2hk.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/keystone-k2l-evm.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/keystone-k2l.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/kirkwood-6192.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/kirkwood-6281.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/kirkwood-6282.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/kirkwood-98dx4122.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/meson.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/meson6.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/meson8.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/meson8b.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/mt2701.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/mt6323.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/mt7623.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/mt7623n-rfb-nand.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap3-beagle-xm.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap3-beagle.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap3-cm-t3517.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap3-cm-t3730.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap3-evm-common.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap3-n900.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap3-overo-base.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap3-tao3530.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap3-zoom3.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap3.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap3430-sdp.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap4-droid4-xt894.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap4-duovero-parlor.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap4-panda-common.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap4-sdp-es23plus.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap4-sdp.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap5-board-common.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/omap5-cm-t54.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/qcom-ipq4019.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/qcom-msm8974.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r7s72100-genmai.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r7s72100-rskrza1.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r7s72100.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r8a7743-iwg20d-q7.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r8a7743-iwg20m.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r8a7743-sk-rzg1m.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r8a7743.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r8a7745-sk-rzg1e.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r8a7745.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r8a7790.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r8a7791-koelsch.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r8a7791.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r8a7792.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r8a7793.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/r8a7794.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3036-kylin.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3036.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3066a-bqcurie2.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3066a-mk808.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3066a-rayeager.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3188-px3-evb.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3188-radxarock.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3229-evb.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk322x.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-evb.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-fennec.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-firefly-reload.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-firefly.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-miqi.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-phycore-rdk.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-phycore-som.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-popmetal.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-r89.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-rock2-som.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-rock2-square.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-tinker.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-veyron-sdmmc.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288-veyron.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rk3288.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rv1108-evb.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/rv1108.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/sama5d2.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/spear1310.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/spear1340.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/ste-dbx5x0.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/stm32429i-eval.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/stm32f429-disco.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/stm32f429.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/stm32f469-disco.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/stm32f746.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/stm32f769-disco.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/stm32h743.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/stm32h743i-eval.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/sun6i-a31.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/sun7i-a20-cubietruck.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/sun8i-a23-a33.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/sun8i-a83t.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/tegra114-dalmore.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/tegra124-jetson-tk1.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/tegra124.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/tegra20-paz00.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/tegra30-beaver.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/tps65217.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-ld4-ref.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-ld4.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-ld6b-ref.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-ld6b.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-pinctrl.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-pro4-ace.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-pro4-ref.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-pro4-sanji.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-pro4.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-pro5.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-pxs2-gentil.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-pxs2-vodka.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-pxs2.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-sld3.dtsi deleted 100644 → 0
View file @ ae46654b
This diff is collapsed.
arch/arm/boot/dts/uniphier-sld8-ref.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/uniphier-sld8.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/versatile-pb.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/zx296702-ad1.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/zynq-7000.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/zynq-parallella.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/zynq-zc702.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/zynq-zc706.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/zynq-zed.dts
View file @ e90937e7
This diff is collapsed.
arch/arm/boot/dts/zynq-zybo.dts
View file @ e90937e7
This diff is collapsed.
arch/arm64/Kconfig.platforms
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/allwinner/Makefile
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/allwinner/axp803.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/amlogic/meson-gx.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/apm/apm-shadowcat.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/apm/apm-storm.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/arm/foundation-v8.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/arm/juno-base.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/broadcom/Makefile
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/broadcom/bcm2835-rpi.dtsi deleted 120000 → 0
View file @ ae46654b
This diff is collapsed.
arch/arm64/boot/dts/broadcom/bcm283x-rpi-smsc9514.dtsi deleted 120000 → 0
View file @ ae46654b
This diff is collapsed.
arch/arm64/boot/dts/broadcom/bcm283x-rpi-usb-host.dtsi deleted 120000 → 0
View file @ ae46654b
This diff is collapsed.
arch/arm64/boot/dts/broadcom/bcm283x.dtsi deleted 120000 → 0
View file @ ae46654b
This diff is collapsed.
arch/arm64/boot/dts/broadcom/northstar2/Makefile 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/broadcom/stingray/stingray-fs4.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/exynos/exynos5433.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/hisilicon/hi3660.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/hisilicon/hi6220.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/hisilicon/hip07-d05.dts
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/hisilicon/hip07.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/marvell/Makefile
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/marvell/armada-8080-db.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/marvell/armada-8080.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/marvell/armada-ap810-ap0-octa-core.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/marvell/armada-ap810-ap0.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/mediatek/Makefile
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/mediatek/mt2712-evb.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/mediatek/mt2712e.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/mediatek/mt6797.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/mediatek/mt7622.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/qcom/Makefile
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/qcom/ipq8074-hk01.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/qcom/ipq8074.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/qcom/msm8916.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/qcom/msm8996.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/qcom/pmi8994.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/renesas/Makefile
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/renesas/r8a7795.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/renesas/r8a7796.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/renesas/r8a77995-draak.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/renesas/r8a77995.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/renesas/ulcb.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/rockchip/Makefile
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/rockchip/rk3328-evb.dts
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/rockchip/rk3328-rock64.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/rockchip/rk3328.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/rockchip/rk3368-r88.dts
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/rockchip/rk3368.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/rockchip/rk3399-evb.dts
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/rockchip/rk3399.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/socionext/Makefile
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/socionext/uniphier-pinctrl.dtsi deleted 120000 → 0
View file @ ae46654b
This diff is collapsed.
arch/arm64/boot/dts/socionext/uniphier-pinctrl.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/socionext/uniphier-ref-daughter.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/socionext/uniphier-support-card.dtsi 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dts
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/xilinx/zynqmp.dtsi
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/zte/Makefile
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/zte/zx296718-evb.dts
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/zte/zx296718-pcbox.dts 0 → 100644
View file @ e90937e7
This diff is collapsed.
arch/arm64/boot/dts/zte/zx296718.dtsi
View file @ e90937e7
This diff is collapsed.
drivers/clk/meson/gxbb.c
View file @ e90937e7
This diff is collapsed.
drivers/clk/meson/gxbb.h
View file @ e90937e7
This diff is collapsed.
drivers/clk/meson/meson8b.c
View file @ e90937e7
This diff is collapsed.
drivers/clk/meson/meson8b.h
View file @ e90937e7
This diff is collapsed.
include/dt-bindings/clock/gxbb-aoclkc.h
View file @ e90937e7
This diff is collapsed.
include/dt-bindings/clock/gxbb-clkc.h
View file @ e90937e7
This diff is collapsed.
include/dt-bindings/clock/meson8b-clkc.h
View file @ e90937e7
This diff is collapsed.
include/dt-bindings/clock/rv1108-cru.h
View file @ e90937e7
This diff is collapsed.
include/dt-bindings/genpd/k2g.h deleted 100644 → 0
View file @ ae46654b
This diff is collapsed.
include/dt-bindings/pinctrl/dra.h
View file @ e90937e7
This diff is collapsed.
include/dt-bindings/reset/amlogic,meson8b-clkc-reset.h 0 → 100644
View file @ e90937e7
This diff is collapsed.
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7