IB/mlx4: Use multiple WQ blocks to post smaller send WQEs

ConnectX HCA supports shrinking WQEs, so that a single work request
can be made of multiple units of wqe_shift.  This way, WRs can differ
in size, and do not have to be a power of 2 in size, saving memory and
speeding up send WR posting.  Unfortunately, if we do this then the
wqe_index field in CQEs can't be used to look up the WR ID anymore, so
our implementation does this only if selective signaling is off.

Further, on 32-bit platforms, we can't use vmap() to make the QP
buffer virtually contigious. Thus we have to use constant-sized WRs to
make sure a WR is always fully within a single page-sized chunk.

Finally, we use WRs with the NOP opcode to avoid wrapping around the
queue buffer in the middle of posting a WR, and we set the
NoErrorCompletion bit to avoid getting completions with error for NOP
WRs.  However, NEC is only supported starting with firmware 2.2.232,
so we use constant-sized WRs for older firmware.  And, since MLX QPs
only support SEND, we use constant-sized WRs in this case.

When stamping during NOP posting, do stamping following setting of the
NOP WQE valid bit.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

drivers/infiniband/hw/mlx4/cq.c

@@ -326,6 +326,12 @@ static int mlx4_ib_poll_one(struct mlx4_ib_cq *cq,
 	is_error = (cqe->owner_sr_opcode & MLX4_CQE_OPCODE_MASK) ==
 		MLX4_CQE_OPCODE_ERROR;
 
+	if (unlikely((cqe->owner_sr_opcode & MLX4_CQE_OPCODE_MASK) == MLX4_OPCODE_NOP &&
+		     is_send)) {
+		printk(KERN_WARNING "Completion for NOP opcode detected!\n");
+		return -EINVAL;
+	}
+
 	if (!*cur_qp ||
 	    (be32_to_cpu(cqe->my_qpn) & 0xffffff) != (*cur_qp)->mqp.qpn) {
 		/*
@@ -348,8 +354,10 @@ static int mlx4_ib_poll_one(struct mlx4_ib_cq *cq,
 
 	if (is_send) {
 		wq = &(*cur_qp)->sq;
+		if (!(*cur_qp)->sq_signal_bits) {
 			wqe_ctr = be16_to_cpu(cqe->wqe_index);
 			wq->tail += (u16) (wqe_ctr - (u16) wq->tail);
+		}
 		wc->wr_id = wq->wrid[wq->tail & (wq->wqe_cnt - 1)];
 		++wq->tail;
 	} else if ((*cur_qp)->ibqp.srq) {

drivers/infiniband/hw/mlx4/mlx4_ib.h

@@ -120,6 +120,8 @@ struct mlx4_ib_qp {
 
 	u32			doorbell_qpn;
 	__be32			sq_signal_bits;
+	unsigned		sq_next_wqe;
+	int			sq_max_wqes_per_wr;
 	int			sq_spare_wqes;
 	struct mlx4_ib_wq	sq;
 

include/linux/mlx4/device.h

@@ -133,6 +133,11 @@ enum {
 	MLX4_STAT_RATE_OFFSET	= 5
 };
 
+static inline u64 mlx4_fw_ver(u64 major, u64 minor, u64 subminor)
+{
+	return (major << 32) | (minor << 16) | subminor;
+}
+
 struct mlx4_caps {
 	u64			fw_ver;
 	int			num_ports;

include/linux/mlx4/qp.h

@@ -154,7 +154,11 @@ struct mlx4_qp_context {
 	u32			reserved5[10];
 };
 
+/* Which firmware version adds support for NEC (NoErrorCompletion) bit */
+#define MLX4_FW_VER_WQE_CTRL_NEC mlx4_fw_ver(2, 2, 232)
+
 enum {
+	MLX4_WQE_CTRL_NEC	= 1 << 29,
 	MLX4_WQE_CTRL_FENCE	= 1 << 6,
 	MLX4_WQE_CTRL_CQ_UPDATE	= 3 << 2,
 	MLX4_WQE_CTRL_SOLICITED	= 1 << 1,