Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC DT updates from Olof Johansson:
 "Most of this branch consists of updates, additions and general churn
  of the device tree source files in the kernel (arch/arm/boot/dts).
  Besides that, there are a few things to point out:

   - Lots of platform conversion on OMAP2+, with removal of old board
     files for various platforms.
   - Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
     well
   - Some updates to pinctrl and other subsystems.  Most of these are
     for DT-enablement of the various platforms and acks have been
     collected"

* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
  ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
  ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
  ARM: dts: bcm281xx: Add card detect GPIO
  ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
  ARM: bcm281xx: Add device node for the GPIO controller
  ARM: mvebu: Add Netgear ReadyNAS 104 board
  ARM: tegra: fix Tegra114 IOMMU register address
  ARM: kirkwood: add support for OpenBlocks A7 platform
  ARM: dts: omap4-panda: add DPI pinmuxing
  ARM: dts: AM33xx: Add RNG node
  ARM: dts: AM33XX: Add hwspinlock node
  ARM: dts: OMAP5: Add hwspinlock node
  ARM: dts: OMAP4: Add hwspinlock node
  ARM: dts: use 'status' property for PCIe nodes
  ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
  ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
  ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
  ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
  ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
  ARM: mvebu: Add the core-divider clock to Armada 370/XP
  ...

Documentation/devicetree/bindings/arm/omap/omap.txt

@@ -21,7 +21,8 @@ Required properties:
 Optional properties:
 - ti,no_idle_on_suspend: When present, it prevents the PM to idle the module
   during suspend.
-
+- ti,no-reset-on-init: When present, the module should not be reset at init
+- ti,no-idle-on-init: When present, the module should not be idled at init
 
 Example:
 

Documentation/devicetree/bindings/arm/vic.txt

@@ -18,6 +18,15 @@ Required properties:
 Optional properties:
 
 - interrupts : Interrupt source for parent controllers if the VIC is nested.
+- valid-mask : A one cell big bit mask of valid interrupt sources. Each bit
+  represents single interrupt source, starting from source 0 at LSb and ending
+  at source 31 at MSb. A bit that is set means that the source is wired and
+  clear means otherwise. If unspecified, defaults to all valid.
+- valid-wakeup-mask : A one cell big bit mask of interrupt sources that can be
+  configured as wake up source for the system. Order of bits is the same as for
+  valid-mask property. A set bit means that this interrupt source can be
+  configured as a wake up source for the system. If unspecied, defaults to all
+  interrupt sources configurable as wake up sources.
 
 Example:
 
@@ -26,4 +35,7 @@ Example:
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		reg = <0x60000 0x1000>;
+
+		valid-mask = <0xffffff7f>;
+		valid-wakeup-mask = <0x0000ff7f>;
 	};

Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt

+* Core Divider Clock bindings for Marvell MVEBU SoCs
+
+The following is a list of provided IDs and clock names on Armada 370/XP:
+ 0 = nand (NAND clock)
+
+Required properties:
+- compatible : must be "marvell,armada-370-corediv-clock"
+- reg : must be the register address of Core Divider control register
+- #clock-cells : from common clock binding; shall be set to 1
+- clocks : must be set to the parent's phandle
+
+Example:
+
+corediv_clk: corediv-clocks@18740 {
+	compatible = "marvell,armada-370-corediv-clock";
+	reg = <0x18740 0xc>;
+	#clock-cells = <1>;
+	clocks = <&pll>;
+};

Documentation/devicetree/bindings/crypto/omap-aes.txt

+OMAP SoC AES crypto Module
+
+Required properties:
+
+- compatible : Should contain entries for this and backward compatible
+  AES versions:
+  - "ti,omap2-aes" for OMAP2.
+  - "ti,omap3-aes" for OMAP3.
+  - "ti,omap4-aes" for OMAP4 and AM33XX.
+  Note that the OMAP2 and 3 versions are compatible (OMAP3 supports
+  more algorithms) but they are incompatible with OMAP4.
+- ti,hwmods: Name of the hwmod associated with the AES module
+- reg : Offset and length of the register set for the module
+- interrupts : the interrupt-specifier for the AES module.
+
+Optional properties:
+- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
+	Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: DMA request names should include "tx" and "rx" if present.
+
+Example:
+	/* AM335x */
+	aes: aes@53500000 {
+		compatible = "ti,omap4-aes";
+		ti,hwmods = "aes";
+		reg = <0x53500000 0xa0>;
+		interrupts = <102>;
+		dmas = <&edma 6>,
+		       <&edma 5>;
+		dma-names = "tx", "rx";
+	};

Documentation/devicetree/bindings/crypto/omap-sham.txt

+OMAP SoC SHA crypto Module
+
+Required properties:
+
+- compatible : Should contain entries for this and backward compatible
+  SHAM versions:
+  - "ti,omap2-sham" for OMAP2 & OMAP3.
+  - "ti,omap4-sham" for OMAP4 and AM33XX.
+  Note that these two versions are incompatible.
+- ti,hwmods: Name of the hwmod associated with the SHAM module
+- reg : Offset and length of the register set for the module
+- interrupts : the interrupt-specifier for the SHAM module.
+
+Optional properties:
+- dmas: DMA specifiers for the rx dma. See the DMA client binding,
+	Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: DMA request name. Should be "rx" if a dma is present.
+
+Example:
+	/* AM335x */
+	sham: sham@53100000 {
+		compatible = "ti,omap4-sham";
+		ti,hwmods = "sham";
+		reg = <0x53100000 0x200>;
+		interrupts = <109>;
+		dmas = <&edma 36>;
+		dma-names = "rx";
+	};

Documentation/devicetree/bindings/hwrng/omap_rng.txt

+OMAP SoC HWRNG Module
+
+Required properties:
+
+- compatible : Should contain entries for this and backward compatible
+  RNG versions:
+  - "ti,omap2-rng" for OMAP2.
+  - "ti,omap4-rng" for OMAP4, OMAP5 and AM33XX.
+  Note that these two versions are incompatible.
+- ti,hwmods: Name of the hwmod associated with the RNG module
+- reg : Offset and length of the register set for the module
+- interrupts : the interrupt number for the RNG module.
+		Only used for "ti,omap4-rng".
+
+Example:
+/* AM335x */
+rng: rng@48310000 {
+	compatible = "ti,omap4-rng";
+	ti,hwmods = "rng";
+	reg = <0x48310000 0x2000>;
+	interrupts = <111>;
+};

Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt

@@ -20,8 +20,29 @@ ti,dual-volt: boolean, supports dual voltage cards
 ti,non-removable: non-removable slot (like eMMC)
 ti,needs-special-reset: Requires a special softreset sequence
 ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed
+dmas: List of DMA specifiers with the controller specific format
+as described in the generic DMA client binding. A tx and rx
+specifier is required.
+dma-names: List of DMA request names. These strings correspond
+1:1 with the DMA specifiers listed in dmas. The string naming is
+to be "rx" and "tx" for RX and TX DMA requests, respectively.
+
+Examples:
+
+[hwmod populated DMA resources]
+
+	mmc1: mmc@0x4809c000 {
+		compatible = "ti,omap4-hsmmc";
+		reg = <0x4809c000 0x400>;
+		ti,hwmods = "mmc1";
+		ti,dual-volt;
+		bus-width = <4>;
+		vmmc-supply = <&vmmc>; /* phandle to regulator node */
+		ti,non-removable;
+	};
+
+[generic DMA request binding]
 
-Example:
 	mmc1: mmc@0x4809c000 {
 		compatible = "ti,omap4-hsmmc";
 		reg = <0x4809c000 0x400>;
@@ -30,4 +51,7 @@ Example:
 		bus-width = <4>;
 		vmmc-supply = <&vmmc>; /* phandle to regulator node */
 		ti,non-removable;
+		dmas = <&edma 24
+			&edma 25>;
+		dma-names = "tx", "rx";
 	};

Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt

@@ -72,6 +72,13 @@ Optional properties:
 		/* pin base, nr pins & gpio function */
 		pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1>;
 
+- interrupt-controller : standard interrupt controller binding if using
+  interrupts for wake-up events for example. In this case pinctrl-single
+  is set up as a chained interrupt controller and the wake-up interrupts
+  can be requested by the drivers using request_irq().
+
+- #interrupt-cells : standard interrupt binding if using interrupts
+
 This driver assumes that there is only one register for each pin (unless the
 pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
 specified in the pinctrl-bindings.txt document in this directory.
@@ -121,6 +128,8 @@ pmx_core: pinmux@4a100040 {
 	reg = <0x4a100040 0x0196>;
 	#address-cells = <1>;
 	#size-cells = <0>;
+	#interrupt-cells = <1>;
+	interrupt-controller;
 	pinctrl-single,register-width = <16>;
 	pinctrl-single,function-mask = <0xffff>;
 };
@@ -131,6 +140,8 @@ pmx_wkup: pinmux@4a31e040 {
 	reg = <0x4a31e040 0x0038>;
 	#address-cells = <1>;
 	#size-cells = <0>;
+	#interrupt-cells = <1>;
+	interrupt-controller;
 	pinctrl-single,register-width = <16>;
 	pinctrl-single,function-mask = <0xffff>;
 };

Documentation/devicetree/bindings/usb/ux500-usb.txt

@@ -15,7 +15,7 @@ Optional properties:
 Example:
 
 usb_per5@a03e0000 {
-	compatible = "stericsson,db8500-musb", "mentor,musb";
+	compatible = "stericsson,db8500-musb";
 	reg = <0xa03e0000 0x10000>;
 	interrupts = <0 23 0x4>;
 	interrupt-names = "mc";

Documentation/devicetree/bindings/video/exynos_hdmi.txt

@@ -12,7 +12,19 @@ Required properties:
 	a) phandle of the gpio controller node.
 	b) pin number within the gpio controller.
 	c) optional flags and pull up/down.
-
+- clocks: list of clock IDs from SoC clock driver.
+	a) hdmi: Gate of HDMI IP bus clock.
+	b) sclk_hdmi: Gate of HDMI special clock.
+	c) sclk_pixel: Pixel special clock, one of the two possible inputs of
+		HDMI clock mux.
+	d) sclk_hdmiphy: HDMI PHY clock output, one of two possible inputs of
+		HDMI clock mux.
+	e) mout_hdmi: It is required by the driver to switch between the 2
+		parents i.e. sclk_pixel and sclk_hdmiphy. If hdmiphy is stable
+		after configuration, parent is set to sclk_hdmiphy else
+		sclk_pixel.
+- clock-names: aliases as per driver requirements for above clock IDs:
+	"hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi".
 Example:
 
 	hdmi {

Documentation/devicetree/bindings/video/exynos_mixer.txt

@@ -10,6 +10,10 @@ Required properties:
 - reg: physical base address of the mixer and length of memory mapped
 	region.
 - interrupts: interrupt number to the cpu.
+- clocks: list of clock IDs from SoC clock driver.
+	a) mixer: Gate of Mixer IP bus clock.
+	b) sclk_hdmi: HDMI Special clock, one of the two possible inputs of
+               mixer mux.
 
 Example:
 

MAINTAINERS

@@ -933,7 +933,7 @@ M:	Javier Martinez Canillas <javier@dowhile0.org>
 L:	linux-omap@vger.kernel.org
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
-F:	arch/arm/mach-omap2/board-igep0020.c
+F:	arch/arm/boot/dts/omap3-igep*
 
 ARM/INCOME PXA270 SUPPORT
 M:	Marek Vasut <marek.vasut@gmail.com>
@@ -6125,6 +6125,12 @@ L:	linux-omap@vger.kernel.org
 S:	Maintained
 F:	drivers/gpio/gpio-omap.c
 
+OMAP/NEWFLOW NANOBONE MACHINE SUPPORT
+M:	Mark Jackson <mpfj@newflow.co.uk>
+L:	linux-omap@vger.kernel.org
+S:	Maintained
+F:	arch/arm/boot/dts/am335x-nano.dts
+
 OMFS FILESYSTEM
 M:	Bob Copeland <me@bobcopeland.com>
 L:	linux-karma-devel@lists.sourceforge.net

arch/arm/boot/dts/Makefile

@@ -40,17 +40,17 @@ dtb-$(CONFIG_ARCH_AT91)	+= sama5d31ek.dtb
 dtb-$(CONFIG_ARCH_AT91)	+= sama5d33ek.dtb
 dtb-$(CONFIG_ARCH_AT91)	+= sama5d34ek.dtb
 dtb-$(CONFIG_ARCH_AT91)	+= sama5d35ek.dtb
-
 dtb-$(CONFIG_ARCH_ATLAS6) += atlas6-evb.dtb
-
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
-dtb-$(CONFIG_ARCH_BCM) += bcm11351-brt.dtb \
+dtb-$(CONFIG_ARCH_BCM_MOBILE) += bcm11351-brt.dtb \
 	bcm28155-ap.dtb
+dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
 dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
 	da850-evm.dtb
 dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \
 	dove-cubox.dtb \
 	dove-d2plug.dtb \
+	dove-d3plug.dtb \
 	dove-dove-db.dtb
 dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos4210-smdkv310.dtb \
@@ -96,22 +96,25 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \
 	kirkwood-ns2mini.dtb \
 	kirkwood-nsa310.dtb \
 	kirkwood-nsa310a.dtb \
+	kirkwood-openblocks_a6.dtb \
+	kirkwood-openblocks_a7.dtb \
 	kirkwood-sheevaplug.dtb \
 	kirkwood-sheevaplug-esata.dtb \
 	kirkwood-topkick.dtb \
 	kirkwood-ts219-6281.dtb \
-	kirkwood-ts219-6282.dtb \
-	kirkwood-openblocks_a6.dtb
+	kirkwood-ts219-6282.dtb
 dtb-$(CONFIG_ARCH_MARCO) += marco-evb.dtb
 dtb-$(CONFIG_ARCH_MSM) += qcom-msm8660-surf.dtb \
 	qcom-msm8960-cdp.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-370-db.dtb \
 	armada-370-mirabox.dtb \
 	armada-370-netgear-rn102.dtb \
+	armada-370-netgear-rn104.dtb \
 	armada-370-rd.dtb \
 	armada-xp-axpwifiap.dtb \
 	armada-xp-db.dtb \
 	armada-xp-gp.dtb \
+	armada-xp-matrix.dtb \
 	armada-xp-openblocks-ax3-4.dtb
 dtb-$(CONFIG_ARCH_MXC) += \
 	imx25-karo-tx25.dtb \
@@ -142,8 +145,10 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx6q-sabrelite.dtb \
 	imx6q-sabresd.dtb \
 	imx6q-sbc6x.dtb \
+	imx6q-udoo.dtb \
 	imx6q-wandboard.dtb \
 	imx6sl-evk.dtb \
+	vf610-cosmic.dtb \
 	vf610-twr.dtb
 dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx23-olinuxino.dtb \
@@ -159,6 +164,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx28-cfa10057.dtb \
 	imx28-cfa10058.dtb \
 	imx28-evk.dtb \
+	imx28-m28cu3.dtb \
 	imx28-m28evk.dtb \
 	imx28-sps1.dtb \
 	imx28-tx28.dtb
@@ -172,9 +178,15 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3-devkit8000.dtb \
 	omap3-beagle-xm.dtb \
 	omap3-evm.dtb \
+	omap3-evm-37xx.dtb \
+	omap3-n900.dtb \
+	omap3-n9.dtb \
+	omap3-n950.dtb \
 	omap3-tobi.dtb \
+	omap3-gta04.dtb \
 	omap3-igep0020.dtb \
 	omap3-igep0030.dtb \
+	omap3-zoom3.dtb \
 	omap4-panda.dtb \
 	omap4-panda-a4.dtb \
 	omap4-panda-es.dtb \
@@ -186,17 +198,24 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	am335x-evmsk.dtb \
 	am335x-bone.dtb \
 	am335x-boneblack.dtb \
+	am335x-nano.dtb \
+	am335x-base0033.dtb \
 	am3517-evm.dtb \
 	am3517_mt_ventoux.dtb \
-	am43x-epos-evm.dtb
+	am43x-epos-evm.dtb \
+	dra7-evm.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
 dtb-$(CONFIG_ARCH_U8500) += ste-snowball.dtb \
-	ste-hrefprev60.dtb \
-	ste-hrefv60plus.dtb \
+	ste-hrefprev60-stuib.dtb \
+	ste-hrefprev60-tvk.dtb \
+	ste-hrefv60plus-stuib.dtb \
+	ste-hrefv60plus-tvk.dtb \
 	ste-ccu8540.dtb \
 	ste-ccu9540.dtb
 dtb-$(CONFIG_ARCH_S3C24XX) += s3c2416-smdk2416.dtb
+dtb-$(CONFIG_ARCH_S3C64XX) += s3c6410-mini6410.dtb \
+	s3c6410-smdk6410.dtb
 dtb-$(CONFIG_ARCH_SHMOBILE) += emev2-kzm9d.dtb \
 	r7s72100-genmai.dtb \
 	r8a7740-armadillo800eva.dtb \
@@ -214,7 +233,9 @@ dtb-$(CONFIG_ARCH_SHMOBILE) += emev2-kzm9d.dtb \
 	r8a73a4-ape6evm-reference.dtb \
 	sh7372-mackerel.dtb
 dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += emev2-kzm9d.dtb
-dtb-$(CONFIG_ARCH_SOCFPGA) += socfpga_cyclone5.dtb \
+dtb-$(CONFIG_ARCH_SOCFPGA) += socfpga_arria5_socdk.dtb \
+	socfpga_cyclone5_socdk.dtb \
+	socfpga_cyclone5_sockit.dtb \
 	socfpga_vt.dtb
 dtb-$(CONFIG_ARCH_SPEAR13XX) += spear1310-evb.dtb \
 	spear1340-evb.dtb
@@ -236,6 +257,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += \
 	sun5i-a13-olinuxino.dtb \
 	sun6i-a31-colombus.dtb \
 	sun7i-a20-cubieboard2.dtb \
+	sun7i-a20-cubietruck.dtb \
 	sun7i-a20-olinuxino-micro.dtb
 dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
 	tegra20-iris-512.dtb \
@@ -250,7 +272,8 @@ dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
 	tegra30-beaver.dtb \
 	tegra30-cardhu-a02.dtb \
 	tegra30-cardhu-a04.dtb \
-	tegra114-dalmore.dtb
+	tegra114-dalmore.dtb \
+	tegra124-venice2.dtb
 dtb-$(CONFIG_ARCH_VERSATILE) += versatile-ab.dtb \
 	versatile-pb.dtb
 dtb-$(CONFIG_ARCH_U300) += ste-u300.dtb

arch/arm/boot/dts/am335x-base0033.dts

+/*
+ * am335x-base0033.dts - Device Tree file for IGEP AQUILA EXPANSION
+ *
+ * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "am335x-igep0033.dtsi"
+
+/ {
+	model = "IGEP COM AM335x on AQUILA Expansion";
+	compatible = "isee,am335x-base0033", "isee,am335x-igep0033", "ti,am33xx";
+};

arch/arm/boot/dts/am335x-bone-common.dtsi

@@ -21,7 +21,50 @@ memory {
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
-	am33xx_pinmux: pinmux@44e10800 {
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_leds_s0>;
+
+		compatible = "gpio-leds";
+
+		led@2 {
+			label = "beaglebone:green:heartbeat";
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led@3 {
+			label = "beaglebone:green:mmc0";
+			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led@4 {
+			label = "beaglebone:green:usr2";
+			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "cpu0";
+			default-state = "off";
+		};
+
+		led@5 {
+			label = "beaglebone:green:usr3";
+			gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
+		};
+	};
+
+	vmmcsd_fixed: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&am33xx_pinmux {
 	pinctrl-names = "default";
 	pinctrl-0 = <&clkout2_pin>;
 
@@ -107,17 +150,37 @@ davinci_mdio_sleep: davinci_mdio_sleep {
 			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
 		>;
 	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x160 (PIN_INPUT | MUX_MODE7) /* GPIO0_6 */
+		>;
 	};
 
-	ocp {
-		uart0: serial@44e09000 {
+	emmc_pins: pinmux_emmc_pins {
+		pinctrl-single,pins = <
+			0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+			0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+			0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+			0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+			0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+			0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+			0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
+			0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
+			0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
+			0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
+		>;
+	};
+};
+
+&uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins>;
 
 	status = "okay";
-		};
+};
 
-		musb: usb@47400000 {
+&usb {
 	status = "okay";
 
 	control@44e10000 {
@@ -144,9 +207,9 @@ usb@47401800 {
 	dma-controller@07402000  {
 		status = "okay";
 	};
-		};
+};
 
-		i2c0: i2c@44e0b000 {
+&i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins>;
 
@@ -157,41 +220,6 @@ tps: tps@24 {
 		reg = <0x24>;
 	};
 
-		};
-	};
-
-	leds {
-		pinctrl-names = "default";
-		pinctrl-0 = <&user_leds_s0>;
-
-		compatible = "gpio-leds";
-
-		led@2 {
-			label = "beaglebone:green:heartbeat";
-			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-
-		led@3 {
-			label = "beaglebone:green:mmc0";
-			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
-
-		led@4 {
-			label = "beaglebone:green:usr2";
-			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
-
-		led@5 {
-			label = "beaglebone:green:usr3";
-			gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
-	};
 };
 
 /include/ "tps65217.dtsi"
@@ -260,3 +288,12 @@ &davinci_mdio {
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
 };
+
+&mmc1 {
+	status = "okay";
+	bus-width = <0x4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+};

arch/arm/boot/dts/am335x-bone.dts

@@ -9,3 +9,21 @@
 
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
+
+&ldo3_reg {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-always-on;
+};
+
+&mmc1 {
+	vmmc-supply = <&ldo3_reg>;
+};
+
+&sham {
+	status = "okay";
+};
+
+&aes {
+	status = "okay";
+};

arch/arm/boot/dts/am335x-boneblack.dts

@@ -15,3 +15,64 @@ &ldo3_reg {
 	regulator-max-microvolt = <1800000>;
 	regulator-always-on;
 };
+
+&mmc1 {
+	vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+	vmmc-supply = <&vmmcsd_fixed>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_pins>;
+	bus-width = <8>;
+	status = "okay";
+	ti,vcc-aux-disable-is-sleep;
+};
+
+&am33xx_pinmux {
+	nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
+		pinctrl-single,pins = <
+			0x1b0 0x03      /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
+			0xa0 0x08       /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xa4 0x08       /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xa8 0x08       /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xac 0x08       /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xb0 0x08       /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xb4 0x08       /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xb8 0x08       /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xbc 0x08       /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xc0 0x08       /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xc4 0x08       /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xc8 0x08       /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xcc 0x08       /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xd0 0x08       /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xd4 0x08       /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xd8 0x08       /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xdc 0x08       /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xe0 0x00       /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+			0xe4 0x00       /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+			0xe8 0x00       /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+			0xec 0x00       /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+		>;
+	};
+	nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
+		pinctrl-single,pins = <
+			0x1b0 0x03      /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
+		>;
+	};
+};
+
+&lcdc {
+	status = "okay";
+};
+
+/ {
+	hdmi {
+		compatible = "ti,tilcdc,slave";
+		i2c = <&i2c0>;
+		pinctrl-names = "default", "off";
+		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+		pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+		status = "okay";
+	};
+};

arch/arm/boot/dts/am335x-evm.dts

@@ -24,7 +24,117 @@ memory {
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
-	am33xx_pinmux: pinmux@44e10800 {
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+
+	lis3_reg: fixedregulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "lis3_reg";
+		regulator-boot-on;
+	};
+
+	matrix_keypad: matrix_keypad@0 {
+		compatible = "gpio-matrix-keypad";
+		debounce-delay-ms = <5>;
+		col-scan-delay-us = <2>;
+
+		row-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH		/* Bank1, pin25 */
+			     &gpio1 26 GPIO_ACTIVE_HIGH		/* Bank1, pin26 */
+			     &gpio1 27 GPIO_ACTIVE_HIGH>;	/* Bank1, pin27 */
+
+		col-gpios = <&gpio1 21 GPIO_ACTIVE_HIGH		/* Bank1, pin21 */
+			     &gpio1 22 GPIO_ACTIVE_HIGH>;	/* Bank1, pin22 */
+
+		linux,keymap = <0x0000008b	/* MENU */
+				0x0100009e	/* BACK */
+				0x02000069	/* LEFT */
+				0x0001006a	/* RIGHT */
+				0x0101001c	/* ENTER */
+				0x0201006c>;	/* DOWN */
+	};
+
+	gpio_keys: volume_keys@0 {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		switch@9 {
+			label = "volume-up";
+			linux,code = <115>;
+			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			gpio-key,wakeup;
+		};
+
+		switch@10 {
+			label = "volume-down";
+			linux,code = <114>;
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+			gpio-key,wakeup;
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 0>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
+
+	panel {
+		compatible = "ti,tilcdc,panel";
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pins_s0>;
+		panel-info {
+			ac-bias           = <255>;
+			ac-bias-intrpt    = <0>;
+			dma-burst-sz      = <16>;
+			bpp               = <32>;
+			fdd               = <0x80>;
+			sync-edge         = <0>;
+			sync-ctrl         = <1>;
+			raster-order      = <0>;
+			fifo-th           = <0>;
+		};
+
+		display-timings {
+			800x480p62 {
+				clock-frequency = <30000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hfront-porch = <39>;
+				hback-porch = <39>;
+				hsync-len = <47>;
+				vback-porch = <29>;
+				vfront-porch = <13>;
+				vsync-len = <2>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "ti,da830-evm-audio";
+		ti,model = "AM335x-EVM";
+		ti,audio-codec = <&tlv320aic3106>;
+		ti,mcasp-controller = <&mcasp1>;
+		ti,codec-clock-rate = <12000000>;
+		ti,audio-routing =
+			"Headphone Jack",       "HPLOUT",
+			"Headphone Jack",       "HPROUT",
+			"LINE1L",               "Line In",
+			"LINE1R",               "Line In";
+	};
+};
+
+&am33xx_pinmux {
 	pinctrl-names = "default";
 	pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
 
@@ -149,17 +259,58 @@ davinci_mdio_sleep: davinci_mdio_sleep {
 			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
 		>;
 	};
+
+	lcd_pins_s0: lcd_pins_s0 {
+		pinctrl-single,pins = <
+			0x20 0x01	/* gpmc_ad8.lcd_data16, OUTPUT | MODE1 */
+			0x24 0x01	/* gpmc_ad9.lcd_data17, OUTPUT | MODE1 */
+			0x28 0x01	/* gpmc_ad10.lcd_data18, OUTPUT | MODE1 */
+			0x2c 0x01	/* gpmc_ad11.lcd_data19, OUTPUT | MODE1 */
+			0x30 0x01	/* gpmc_ad12.lcd_data20, OUTPUT | MODE1 */
+			0x34 0x01	/* gpmc_ad13.lcd_data21, OUTPUT | MODE1 */
+			0x38 0x01	/* gpmc_ad14.lcd_data22, OUTPUT | MODE1 */
+			0x3c 0x01	/* gpmc_ad15.lcd_data23, OUTPUT | MODE1 */
+			0xa0 0x00	/* lcd_data0.lcd_data0, OUTPUT | MODE0 */
+			0xa4 0x00	/* lcd_data1.lcd_data1, OUTPUT | MODE0 */
+			0xa8 0x00	/* lcd_data2.lcd_data2, OUTPUT | MODE0 */
+			0xac 0x00	/* lcd_data3.lcd_data3, OUTPUT | MODE0 */
+			0xb0 0x00	/* lcd_data4.lcd_data4, OUTPUT | MODE0 */
+			0xb4 0x00	/* lcd_data5.lcd_data5, OUTPUT | MODE0 */
+			0xb8 0x00	/* lcd_data6.lcd_data6, OUTPUT | MODE0 */
+			0xbc 0x00	/* lcd_data7.lcd_data7, OUTPUT | MODE0 */
+			0xc0 0x00	/* lcd_data8.lcd_data8, OUTPUT | MODE0 */
+			0xc4 0x00	/* lcd_data9.lcd_data9, OUTPUT | MODE0 */
+			0xc8 0x00	/* lcd_data10.lcd_data10, OUTPUT | MODE0 */
+			0xcc 0x00	/* lcd_data11.lcd_data11, OUTPUT | MODE0 */
+			0xd0 0x00	/* lcd_data12.lcd_data12, OUTPUT | MODE0 */
+			0xd4 0x00	/* lcd_data13.lcd_data13, OUTPUT | MODE0 */
+			0xd8 0x00	/* lcd_data14.lcd_data14, OUTPUT | MODE0 */
+			0xdc 0x00	/* lcd_data15.lcd_data15, OUTPUT | MODE0 */
+			0xe0 0x00	/* lcd_vsync.lcd_vsync, OUTPUT | MODE0 */
+			0xe4 0x00	/* lcd_hsync.lcd_hsync, OUTPUT | MODE0 */
+			0xe8 0x00	/* lcd_pclk.lcd_pclk, OUTPUT | MODE0 */
+			0xec 0x00	/* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */
+		>;
 	};
 
-	ocp {
-		uart0: serial@44e09000 {
+	am335x_evm_audio_pins: am335x_evm_audio_pins {
+		pinctrl-single,pins = <
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rx_dv.mcasp1_aclkx */
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_txd3.mcasp1_fsx */
+			0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+		>;
+	};
+};
+
+&uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins>;
 
 	status = "okay";
-		};
+};
 
-		i2c0: i2c@44e0b000 {
+&i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins>;
 
@@ -169,9 +320,9 @@ i2c0: i2c@44e0b000 {
 	tps: tps@2d {
 		reg = <0x2d>;
 	};
-		};
+};
 
-		musb: usb@47400000 {
+&usb {
 	status = "okay";
 
 	control@44e10000 {
@@ -198,9 +349,9 @@ usb@47401800 {
 	dma-controller@07402000  {
 		status = "okay";
 	};
-		};
+};
 
-		i2c1: i2c@4802a000 {
+&i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c1_pins>;
 
@@ -244,13 +395,29 @@ tmp275: tmp275@48 {
 		compatible = "ti,tmp275";
 		reg = <0x48>;
 	};
-		};
 
-		elm: elm@48080000 {
+	tlv320aic3106: tlv320aic3106@1b {
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
 		status = "okay";
+
+		/* Regulators */
+		AVDD-supply = <&vaux2_reg>;
+		IOVDD-supply = <&vaux2_reg>;
+		DRVDD-supply = <&vaux2_reg>;
+		DVDD-supply = <&vbat>;
 	};
+};
 
-		epwmss0: epwmss@48300000 {
+&lcdc {
+	status = "okay";
+};
+
+&elm {
+	status = "okay";
+};
+
+&epwmss0 {
 	status = "okay";
 
 	ecap0: ecap@48300100 {
@@ -258,9 +425,9 @@ ecap0: ecap@48300100 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&ecap0_pins>;
 	};
-		};
+};
 
-		gpmc: gpmc@50000000 {
+&gpmc {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&nandflash_pins_s0>;
@@ -339,74 +506,26 @@ partition@7 {
 			reg = <0x00780000 0x0F880000>;
 		};
 	};
-		};
-	};
-
-	vbat: fixedregulator@0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vbat";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-boot-on;
-	};
-
-	lis3_reg: fixedregulator@1 {
-		compatible = "regulator-fixed";
-		regulator-name = "lis3_reg";
-		regulator-boot-on;
-	};
-
-	matrix_keypad: matrix_keypad@0 {
-		compatible = "gpio-matrix-keypad";
-		debounce-delay-ms = <5>;
-		col-scan-delay-us = <2>;
-
-		row-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH		/* Bank1, pin25 */
-			     &gpio1 26 GPIO_ACTIVE_HIGH		/* Bank1, pin26 */
-			     &gpio1 27 GPIO_ACTIVE_HIGH>;	/* Bank1, pin27 */
-
-		col-gpios = <&gpio1 21 GPIO_ACTIVE_HIGH		/* Bank1, pin21 */
-			     &gpio1 22 GPIO_ACTIVE_HIGH>;	/* Bank1, pin22 */
-
-		linux,keymap = <0x0000008b	/* MENU */
-				0x0100009e	/* BACK */
-				0x02000069	/* LEFT */
-				0x0001006a	/* RIGHT */
-				0x0101001c	/* ENTER */
-				0x0201006c>;	/* DOWN */
-	};
+};
 
-	gpio_keys: volume_keys@0 {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		autorepeat;
+#include "tps65910.dtsi"
 
-		switch@9 {
-			label = "volume-up";
-			linux,code = <115>;
-			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
-			gpio-key,wakeup;
-		};
+&mcasp1 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&am335x_evm_audio_pins>;
 
-		switch@10 {
-			label = "volume-down";
-			linux,code = <114>;
-			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
-			gpio-key,wakeup;
-		};
-	};
+		status = "okay";
 
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&ecap0 0 50000 0>;
-		brightness-levels = <0 51 53 56 62 75 101 152 255>;
-		default-brightness-level = <8>;
-	};
+		op-mode = <0>;          /* MCASP_IIS_MODE */
+		tdm-slots = <2>;
+		/* 4 serializers */
+		serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+			0 0 1 2
+		>;
+		tx-num-evt = <1>;
+		rx-num-evt = <1>;
 };
 
-#include "tps65910.dtsi"
-
 &tps {
 	vcc1-supply = <&vbat>;
 	vcc2-supply = <&vbat>;
@@ -477,6 +596,8 @@ vaux33_reg: regulator@11 {
 		};
 
 		vmmc_reg: regulator@12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
 			regulator-always-on;
 		};
 	};
@@ -517,3 +638,17 @@ adc {
 		ti,adc-channels = <4 5 6 7>;
 	};
 };
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmc_reg>;
+	bus-width = <4>;
+};
+
+&sham {
+	status = "okay";
+};
+
+&aes {
+	status = "okay";
+};

arch/arm/boot/dts/am335x-evmsk.dts

@@ -31,7 +31,104 @@ memory {
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
-	am33xx_pinmux: pinmux@44e10800 {
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+
+	lis3_reg: fixedregulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "lis3_reg";
+		regulator-boot-on;
+	};
+
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_leds_s0>;
+
+		compatible = "gpio-leds";
+
+		led@1 {
+			label = "evmsk:green:usr0";
+			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led@2 {
+			label = "evmsk:green:usr1";
+			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led@3 {
+			label = "evmsk:green:mmc0";
+			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led@4 {
+			label = "evmsk:green:heartbeat";
+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+
+	gpio_buttons: gpio_buttons@0 {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch@1 {
+			label = "button0";
+			linux,code = <0x100>;
+			gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		switch@2 {
+			label = "button1";
+			linux,code = <0x101>;
+			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		switch@3 {
+			label = "button2";
+			linux,code = <0x102>;
+			gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>;
+			gpio-key,wakeup;
+		};
+
+		switch@4 {
+			label = "button3";
+			linux,code = <0x103>;
+			gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap2 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 58 61 66 75 90 125 170 255>;
+		default-brightness-level = <8>;
+	};
+
+	sound {
+		compatible = "ti,da830-evm-audio";
+		ti,model = "AM335x-EVMSK";
+		ti,audio-codec = <&tlv320aic3106>;
+		ti,mcasp-controller = <&mcasp1>;
+		ti,codec-clock-rate = <24576000>;
+		ti,audio-routing =
+			"Headphone Jack",       "HPLOUT",
+			"Headphone Jack",       "HPROUT";
+	};
+};
+
+&am33xx_pinmux {
 	pinctrl-names = "default";
 	pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>;
 
@@ -158,17 +255,25 @@ davinci_mdio_sleep: davinci_mdio_sleep {
 			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
 		>;
 	};
+
+	mcasp1_pins: mcasp1_pins {
+		pinctrl-single,pins = <
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */
+			0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+		>;
 	};
+};
 
-	ocp {
-		uart0: serial@44e09000 {
+&uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins>;
 
 	status = "okay";
-		};
+};
 
-		i2c0: i2c@44e0b000 {
+&i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins>;
 
@@ -206,9 +311,21 @@ lis331dlh: lis331dlh@18 {
 		st,max-limit-y = <550>;
 		st,max-limit-z = <750>;
 	};
+
+	tlv320aic3106: tlv320aic3106@1b {
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		status = "okay";
+
+		/* Regulators */
+		AVDD-supply = <&vaux2_reg>;
+		IOVDD-supply = <&vaux2_reg>;
+		DRVDD-supply = <&vaux2_reg>;
+		DVDD-supply = <&vbat>;
 	};
+};
 
-		musb: usb@47400000 {
+&usb {
 	status = "okay";
 
 	control@44e10000 {
@@ -222,9 +339,9 @@ usb-phy@47401300 {
 	usb@47401000 {
 		status = "okay";
 	};
-		};
+};
 
-		epwmss2: epwmss@48304000 {
+&epwmss2 {
 	status = "okay";
 
 	ecap2: ecap@48304100 {
@@ -232,93 +349,6 @@ ecap2: ecap@48304100 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&ecap2_pins>;
 	};
-		};
-	};
-
-	vbat: fixedregulator@0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vbat";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-boot-on;
-	};
-
-	lis3_reg: fixedregulator@1 {
-		compatible = "regulator-fixed";
-		regulator-name = "lis3_reg";
-		regulator-boot-on;
-	};
-
-	leds {
-		pinctrl-names = "default";
-		pinctrl-0 = <&user_leds_s0>;
-
-		compatible = "gpio-leds";
-
-		led@1 {
-			label = "evmsk:green:usr0";
-			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
-
-		led@2 {
-			label = "evmsk:green:usr1";
-			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
-
-		led@3 {
-			label = "evmsk:green:mmc0";
-			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
-
-		led@4 {
-			label = "evmsk:green:heartbeat";
-			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-	};
-
-	gpio_buttons: gpio_buttons@0 {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		switch@1 {
-			label = "button0";
-			linux,code = <0x100>;
-			gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
-		};
-
-		switch@2 {
-			label = "button1";
-			linux,code = <0x101>;
-			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
-		};
-
-		switch@3 {
-			label = "button2";
-			linux,code = <0x102>;
-			gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>;
-			gpio-key,wakeup;
-		};
-
-		switch@4 {
-			label = "button3";
-			linux,code = <0x103>;
-			gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&ecap2 0 50000 PWM_POLARITY_INVERTED>;
-		brightness-levels = <0 58 61 66 75 90 125 170 255>;
-		default-brightness-level = <8>;
-	};
 };
 
 #include "tps65910.dtsi"
@@ -393,6 +423,8 @@ vaux33_reg: regulator@11 {
 		};
 
 		vmmc_reg: regulator@12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
 			regulator-always-on;
 		};
 	};
@@ -419,3 +451,37 @@ &cpsw_emac1 {
 	phy_id = <&davinci_mdio>, <1>;
 	phy-mode = "rgmii-txid";
 };
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmc_reg>;
+	bus-width = <4>;
+};
+
+&sham {
+	status = "okay";
+};
+
+&aes {
+	status = "okay";
+};
+
+&gpio0 {
+	ti,no-reset-on-init;
+};
+
+&mcasp1 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcasp1_pins>;
+
+		status = "okay";
+
+		op-mode = <0>;          /* MCASP_IIS_MODE */
+		tdm-slots = <2>;
+		/* 4 serializers */
+		serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+			0 0 1 2
+		>;
+		tx-num-evt = <1>;
+		rx-num-evt = <1>;
+};

arch/arm/boot/dts/am335x-igep0033.dtsi

+/*
+ * am335x-igep0033.dtsi - Device Tree file for IGEP COM AQUILA AM335x
+ *
+ * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vdd1_reg>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_pins>;
+
+		compatible = "gpio-leds";
+
+		led@0 {
+			label = "com:green:user";
+			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+
+	vmmc: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&am33xx_pinmux {
+	i2c0_pins: pinmux_i2c0_pins {
+		pinctrl-single,pins = <
+			0x188 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+			0x18c (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	nandflash_pins: pinmux_nandflash_pins {
+		pinctrl-single,pins = <
+			0x0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+			0x4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+			0x8 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+			0xc (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+			0x10 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+			0x14 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+			0x18 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+			0x1c (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+			0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+			0x74 (PIN_INPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpio0_30 */
+			0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0 */
+			0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
+			0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
+			0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
+			0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+		>;
+	};
+
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			0x170 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+			0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+		>;
+	};
+
+	leds_pins: pinmux_leds_pins {
+		pinctrl-single,pins = <
+			0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a7.gpio1_23 */
+		>;
+	};
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <1>;
+};
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nandflash_pins>;
+
+	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+
+	nand@0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		nand-bus-width = <8>;
+		ti,nand-ecc-opt = "bch8";
+		gpmc,device-nand = "true";
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		elm_id = <&elm>;
+
+		/* MTD partition table */
+		partition@0 {
+			label = "SPL";
+			reg = <0x00000000 0x000080000>;
+		};
+
+		partition@1 {
+			label = "U-boot";
+			reg = <0x00080000 0x001e0000>;
+		};
+
+		partition@2 {
+			label = "U-Boot Env";
+			reg = <0x00260000 0x00020000>;
+		};
+
+		partition@3 {
+			label = "Kernel";
+			reg = <0x00280000 0x00500000>;
+		};
+
+		partition@4 {
+			label = "File System";
+			reg = <0x00780000 0x007880000>;
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	clock-frequency = <400000>;
+
+	tps: tps@2d {
+		reg = <0x2d>;
+	};
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmc>;
+	bus-width = <4>;
+};
+
+&uart0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+};
+
+#include "tps65910.dtsi"
+
+&tps {
+	vcc1-supply = <&vbat>;
+	vcc2-supply = <&vbat>;
+	vcc3-supply = <&vbat>;
+	vcc4-supply = <&vbat>;
+	vcc5-supply = <&vbat>;
+	vcc6-supply = <&vbat>;
+	vcc7-supply = <&vbat>;
+	vccio-supply = <&vbat>;
+
+	regulators {
+		vrtc_reg: regulator@0 {
+			regulator-always-on;
+		};
+
+		vio_reg: regulator@1 {
+			regulator-always-on;
+		};
+
+		vdd1_reg: regulator@2 {
+			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1312500>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd2_reg: regulator@3 {
+			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1150000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd3_reg: regulator@4 {
+			regulator-always-on;
+		};
+
+		vdig1_reg: regulator@5 {
+			regulator-always-on;
+		};
+
+		vdig2_reg: regulator@6 {
+			regulator-always-on;
+		};
+
+		vpll_reg: regulator@7 {
+			regulator-always-on;
+		};
+
+		vdac_reg: regulator@8 {
+			regulator-always-on;
+		};
+
+		vaux1_reg: regulator@9 {
+			regulator-always-on;
+		};
+
+		vaux2_reg: regulator@10 {
+			regulator-always-on;
+		};
+
+		vaux33_reg: regulator@11 {
+			regulator-always-on;
+		};
+
+		vmmc_reg: regulator@12 {
+			regulator-always-on;
+		};
+	};
+};
+

arch/arm/boot/dts/am33xx.dtsi

@@ -18,6 +18,9 @@ / {
 	interrupt-parent = <&intc>;
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &uart2;
@@ -30,6 +33,8 @@ aliases {
 		usb1 = &usb1;
 		phy0 = &usb0_phy;
 		phy1 = &usb1_phy;
+		ethernet0 = &cpsw_emac0;
+		ethernet1 = &cpsw_emac1;
 	};
 
 	cpus {
@@ -57,6 +62,11 @@ cpu@0 {
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a8-pmu";
+		interrupts = <3>;
+	};
+
 	/*
 	 * The soc node represents the soc top level view. It is uses for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
@@ -100,13 +110,25 @@ intc: interrupt-controller@48200000 {
 			reg = <0x48200000 0x1000>;
 		};
 
+		edma: edma@49000000 {
+			compatible = "ti,edma3";
+			ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
+			reg =	<0x49000000 0x10000>,
+				<0x44e10f90 0x10>;
+			interrupts = <12 13 14>;
+			#dma-cells = <1>;
+			dma-channels = <64>;
+			ti,edma-regions = <4>;
+			ti,edma-slots = <256>;
+		};
+
 		gpio0: gpio@44e07000 {
 			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio1";
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			reg = <0x44e07000 0x1000>;
 			interrupts = <96>;
 		};
@@ -117,7 +139,7 @@ gpio1: gpio@4804c000 {
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			reg = <0x4804c000 0x1000>;
 			interrupts = <98>;
 		};
@@ -128,7 +150,7 @@ gpio2: gpio@481ac000 {
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			reg = <0x481ac000 0x1000>;
 			interrupts = <32>;
 		};
@@ -139,7 +161,7 @@ gpio3: gpio@481ae000 {
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			reg = <0x481ae000 0x1000>;
 			interrupts = <62>;
 		};
@@ -228,6 +250,50 @@ i2c2: i2c@4819c000 {
 			status = "disabled";
 		};
 
+		mmc1: mmc@48060000 {
+			compatible = "ti,omap4-hsmmc";
+			ti,hwmods = "mmc1";
+			ti,dual-volt;
+			ti,needs-special-reset;
+			ti,needs-special-hs-handling;
+			dmas = <&edma 24
+				&edma 25>;
+			dma-names = "tx", "rx";
+			interrupts = <64>;
+			interrupt-parent = <&intc>;
+			reg = <0x48060000 0x1000>;
+			status = "disabled";
+		};
+
+		mmc2: mmc@481d8000 {
+			compatible = "ti,omap4-hsmmc";
+			ti,hwmods = "mmc2";
+			ti,needs-special-reset;
+			dmas = <&edma 2
+				&edma 3>;
+			dma-names = "tx", "rx";
+			interrupts = <28>;
+			interrupt-parent = <&intc>;
+			reg = <0x481d8000 0x1000>;
+			status = "disabled";
+		};
+
+		mmc3: mmc@47810000 {
+			compatible = "ti,omap4-hsmmc";
+			ti,hwmods = "mmc3";
+			ti,needs-special-reset;
+			interrupts = <29>;
+			interrupt-parent = <&intc>;
+			reg = <0x47810000 0x1000>;
+			status = "disabled";
+		};
+
+		hwspinlock: spinlock@480ca000 {
+			compatible = "ti,omap4-hwspinlock";
+			reg = <0x480ca000 0x1000>;
+			ti,hwmods = "spinlock";
+		};
+
 		wdt2: wdt@44e35000 {
 			compatible = "ti,omap3-wdt";
 			ti,hwmods = "wd_timer2";
@@ -323,6 +389,11 @@ spi0: spi@48030000 {
 			interrupts = <65>;
 			ti,spi-num-cs = <2>;
 			ti,hwmods = "spi0";
+			dmas = <&edma 16
+				&edma 17
+				&edma 18
+				&edma 19>;
+			dma-names = "tx0", "rx0", "tx1", "rx1";
 			status = "disabled";
 		};
 
@@ -334,6 +405,11 @@ spi1: spi@481a0000 {
 			interrupts = <125>;
 			ti,spi-num-cs = <2>;
 			ti,hwmods = "spi1";
+			dmas = <&edma 42
+				&edma 43
+				&edma 44
+				&edma 45>;
+			dma-names = "tx0", "rx0", "tx1", "rx1";
 			status = "disabled";
 		};
 
@@ -346,7 +422,7 @@ usb: usb@47400000 {
 			ti,hwmods = "usb_otg_hs";
 			status = "disabled";
 
-			ctrl_mod: control@44e10000 {
+			usb_ctrl_mod: control@44e10000 {
 				compatible = "ti,am335x-usb-ctrl-module";
 				reg = <0x44e10620 0x10
 					0x44e10648 0x4>;
@@ -359,7 +435,7 @@ usb0_phy: usb-phy@47401300 {
 				reg = <0x47401300 0x100>;
 				reg-names = "phy";
 				status = "disabled";
-				ti,ctrl_mod = <&ctrl_mod>;
+				ti,ctrl_mod = <&usb_ctrl_mod>;
 			};
 
 			usb0: usb@47401000 {
@@ -407,7 +483,7 @@ usb1_phy: usb-phy@47401b00 {
 				reg = <0x47401b00 0x100>;
 				reg-names = "phy";
 				status = "disabled";
-				ti,ctrl_mod = <&ctrl_mod>;
+				ti,ctrl_mod = <&usb_ctrl_mod>;
 			};
 
 			usb1: usb@47401800 {
@@ -607,6 +683,7 @@ wkup_m3: wkup_m3@44d00000 {
 			reg = <0x44d00000 0x4000	/* M3 UMEM */
 			       0x44d80000 0x2000>;	/* M3 DMEM */
 			ti,hwmods = "wkup_m3";
+			ti,no-reset-on-init;
 		};
 
 		elm: elm@48080000 {
@@ -617,6 +694,15 @@ elm: elm@48080000 {
 			status = "disabled";
 		};
 
+		lcdc: lcdc@4830e000 {
+			compatible = "ti,am33xx-tilcdc";
+			reg = <0x4830e000 0x1000>;
+			interrupt-parent = <&intc>;
+			interrupts = <36>;
+			ti,hwmods = "lcdc";
+			status = "disabled";
+		};
+
 		tscadc: tscadc@44e0d000 {
 			compatible = "ti,am3359-tscadc";
 			reg = <0x44e0d000 0x1000>;
@@ -637,6 +723,7 @@ am335x_adc: adc {
 		gpmc: gpmc@50000000 {
 			compatible = "ti,am3352-gpmc";
 			ti,hwmods = "gpmc";
+			ti,no-idle-on-init;
 			reg = <0x50000000 0x2000>;
 			interrupts = <100>;
 			gpmc,num-cs = <7>;
@@ -645,5 +732,59 @@ gpmc: gpmc@50000000 {
 			#size-cells = <1>;
 			status = "disabled";
 		};
+
+		sham: sham@53100000 {
+			compatible = "ti,omap4-sham";
+			ti,hwmods = "sham";
+			reg = <0x53100000 0x200>;
+			interrupts = <109>;
+			dmas = <&edma 36>;
+			dma-names = "rx";
+		};
+
+		aes: aes@53500000 {
+			compatible = "ti,omap4-aes";
+			ti,hwmods = "aes";
+			reg = <0x53500000 0xa0>;
+			interrupts = <103>;
+			dmas = <&edma 6>,
+			       <&edma 5>;
+			dma-names = "tx", "rx";
+		};
+
+		mcasp0: mcasp@48038000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp0";
+			reg = <0x48038000 0x2000>,
+			      <0x46000000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <80>, <81>;
+			interrupts-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 8>,
+				<&edma 9>;
+			dma-names = "tx", "rx";
+		};
+
+		mcasp1: mcasp@4803C000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp1";
+			reg = <0x4803C000 0x2000>,
+			      <0x46400000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <82>, <83>;
+			interrupts-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 10>,
+				<&edma 11>;
+			dma-names = "tx", "rx";
+		};
+
+		rng: rng@48310000 {
+			compatible = "ti,omap4-rng";
+			ti,hwmods = "rng";
+			reg = <0x48310000 0x2000>;
+			interrupts = <111>;
+		};
 	};
 };

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -11,8 +11,176 @@
 /dts-v1/;
 
 #include "am4372.dtsi"
+#include <dt-bindings/pinctrl/am43xx.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "TI AM43x EPOS EVM";
 	compatible = "ti,am43x-epos-evm","ti,am4372","ti,am43";
+
+	vmmcsd_fixed: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+	};
+
+	am43xx_pinmux: pinmux@44e10800 {
+		cpsw_default: cpsw_default {
+			pinctrl-single,pins = <
+				/* Slave 1 */
+				0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_crs.rmii1_crs */
+				0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxerr.rmii1_rxerr */
+				0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_txen.rmii1_txen */
+				0x118 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxdv.rmii1_rxdv */
+				0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_txd1.rmii1_txd1 */
+				0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_txd0.rmii1_txd0 */
+				0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxd1.rmii1_rxd1 */
+				0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxd0.rmii1_rxd0 */
+				0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* rmii1_refclk.rmii1_refclk */
+			>;
+		};
+
+		cpsw_sleep: cpsw_sleep {
+			pinctrl-single,pins = <
+				/* Slave 1 reset value */
+				0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			>;
+		};
+
+		davinci_mdio_default: davinci_mdio_default {
+			pinctrl-single,pins = <
+				/* MDIO */
+				0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+				0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
+			>;
+		};
+
+		davinci_mdio_sleep: davinci_mdio_sleep {
+			pinctrl-single,pins = <
+				/* MDIO reset value */
+				0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			>;
+		};
+
+		i2c0_pins: pinmux_i2c0_pins {
+			pinctrl-single,pins = <
+				0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+				0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+			>;
+		};
+	};
+
+	matrix_keypad: matrix_keypad@0 {
+			compatible = "gpio-matrix-keypad";
+			debounce-delay-ms = <5>;
+			col-scan-delay-us = <2>;
+
+			row-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH		/* Bank0, pin12 */
+				     &gpio0 13 GPIO_ACTIVE_HIGH		/* Bank0, pin13 */
+				     &gpio0 14 GPIO_ACTIVE_HIGH		/* Bank0, pin14 */
+				     &gpio0 15 GPIO_ACTIVE_HIGH>;	/* Bank0, pin15 */
+
+			col-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH		/* Bank3, pin9 */
+				     &gpio3 10 GPIO_ACTIVE_HIGH		/* Bank3, pin10 */
+				     &gpio2 18 GPIO_ACTIVE_HIGH		/* Bank2, pin18 */
+				     &gpio2 19 GPIO_ACTIVE_HIGH>;	/* Bank2, pin19 */
+
+			linux,keymap = <0x00000201	/* P1 */
+				0x01000204	/* P4 */
+				0x02000207	/* P7 */
+				0x0300020a	/* NUMERIC_STAR */
+				0x00010202	/* P2 */
+				0x01010205	/* P5 */
+				0x02010208	/* P8 */
+				0x03010200	/* P0 */
+				0x00020203	/* P3 */
+				0x01020206	/* P6 */
+				0x02020209	/* P9 */
+				0x0302020b	/* NUMERIC_POUND */
+				0x00030067	/* UP */
+				0x0103006a	/* RIGHT */
+				0x0203006c	/* DOWN */
+				0x03030069>;	/* LEFT */
+		};
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+};
+
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <16>;
+	phy-mode = "rmii";
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <1>;
+	phy-mode = "rmii";
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	at24@50 {
+		compatible = "at24,24c256";
+		pagesize = <64>;
+		reg = <0x50>;
+	};
+
+	pixcir_ts@5c {
+		compatible = "pixcir,pixcir_ts";
+		reg = <0x5c>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <17 0>;
+
+		attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+
+		x-size = <1024>;
+		y-size = <768>;
+	};
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&gpio3 {
+	status = "okay";
 };

arch/arm/boot/dts/armada-370-netgear-rn104.dts

+/*
+ * Device Tree file for NETGEAR ReadyNAS 104
+ *
+ * Copyright (C) 2013, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+/dts-v1/;
+
+#include "armada-370.dtsi"
+
+/ {
+	model = "NETGEAR ReadyNAS 104";
+	compatible = "netgear,readynas-104", "marvell,armada370", "marvell,armada-370-xp";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>; /* 512 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+			  MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
+
+		pcie-controller {
+			status = "okay";
+
+			/* Connected to FL1009 USB 3.0 controller */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+
+			/* Connected to Marvell 88SE9215 SATA controller */
+			pcie@2,0 {
+				/* Port 1, Lane 0 */
+				status = "okay";
+			};
+		};
+
+		internal-regs {
+			serial@12000 {
+				clock-frequency = <200000000>;
+				status = "okay";
+			};
+
+			pinctrl {
+				poweroff: poweroff {
+					marvell,pins = "mpp60";
+					marvell,function = "gpio";
+				};
+
+				backup_key_pin: backup-key-pin {
+					marvell,pins = "mpp52";
+					marvell,function = "gpio";
+				};
+
+				power_key_pin: power-key-pin {
+					marvell,pins = "mpp62";
+					marvell,function = "gpio";
+				};
+
+				backup_led_pin: backup-led-pin {
+					marvell,pins = "mpp63";
+					marvell,function = "gpo";
+				};
+
+				power_led_pin: power-led-pin {
+					marvell,pins = "mpp64";
+					marvell,function = "gpio";
+				};
+
+				reset_key_pin: reset-key-pin {
+					marvell,pins = "mpp65";
+					marvell,function = "gpio";
+				};
+			};
+
+			mdio {
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "rgmii-id";
+			};
+
+			ethernet@74000 {
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "rgmii-id";
+			};
+
+			usb@50000 {
+				status = "okay";
+			};
+
+			i2c@11000 {
+				compatible = "marvell,mv64xxx-i2c";
+				clock-frequency = <100000>;
+				status = "okay";
+
+				g762: g762@3e {
+					compatible = "gmt,g762";
+					reg = <0x3e>;
+					clocks = <&g762_clk>; /* input clock */
+					fan_gear_mode = <0>;
+					fan_startv = <1>;
+					pwm_polarity = <0>;
+				};
+			};
+		};
+	};
+
+	clocks {
+	       #address-cells = <1>;
+	       #size-cells = <0>;
+
+	       g762_clk: fixedclk {
+			 compatible = "fixed-clock";
+			 #clock-cells = <0>;
+			 clock-frequency = <8192>;
+	       };
+	};
+
+	gpio_leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&backup_led_pin &power_led_pin>;
+		pinctrl-names = "default";
+
+		blue_backup_led {
+			label = "rn104:blue:backup";
+			gpios = <&gpio1 31 0>;   /* GPIO 63 Active High */
+			default-state = "off";
+		};
+
+		blue_power_led {
+			label = "rn104:blue:pwr";
+			gpios = <&gpio2 0 1>;    /* GPIO 64 Active Low */
+			linux,default-trigger = "keep";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&backup_key_pin
+			     &power_key_pin
+			     &reset_key_pin>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "Backup Button";
+			linux,code = <133>;     /* KEY_COPY */
+			gpios = <&gpio1 20 1>;
+		};
+
+		button@2 {
+			label = "Power Button";
+			linux,code = <116>;     /* KEY_POWER */
+			gpios = <&gpio1 30 0>;
+		};
+
+		button@3 {
+			label = "Reset Button";
+			linux,code = <0x198>;   /* KEY_RESTART */
+			gpios = <&gpio2 1 1>;
+		};
+	};
+
+	gpio_poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-0 = <&poweroff>;
+		pinctrl-names = "default";
+		gpios = <&gpio1 28 1>;
+	};
+};

arch/arm/boot/dts/armada-370-xp.dtsi

@@ -113,6 +113,7 @@ mpic: interrupt-controller@20000 {
 				#interrupt-cells = <1>;
 				#size-cells = <1>;
 				interrupt-controller;
+				msi-controller;
 			};
 
 			coherency-fabric@20200 {
@@ -137,6 +138,14 @@ serial@12100 {
 				status = "disabled";
 			};
 
+			coredivclk: corediv-clock@18740 {
+				compatible = "marvell,armada-370-corediv-clock";
+				reg = <0x18740 0xc>;
+				#clock-cells = <1>;
+				clocks = <&mainpll>;
+				clock-output-names = "nand";
+			};
+
 			timer@20300 {
 				reg = <0x20300 0x30>, <0x21040 0x30>;
 				interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
@@ -176,7 +185,6 @@ eth1: ethernet@74000 {
 
 			i2c0: i2c@11000 {
 				compatible = "marvell,mv64xxx-i2c";
-				reg = <0x11000 0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 				interrupts = <31>;
@@ -187,7 +195,6 @@ i2c0: i2c@11000 {
 
 			i2c1: i2c@11100 {
 				compatible = "marvell,mv64xxx-i2c";
-				reg = <0x11100 0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 				interrupts = <32>;
@@ -252,4 +259,13 @@ spi1: spi@10680 {
 
 		};
 	};
+
+	clocks {
+		/* 2 GHz fixed main PLL */
+		mainpll: mainpll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <2000000000>;
+		};
+	};
  };

arch/arm/boot/dts/armada-370.dtsi

@@ -44,6 +44,7 @@ pcie-controller {
 			#address-cells = <3>;
 			#size-cells = <2>;
 
+			msi-parent = <&mpic>;
 			bus-range = <0x00 0xff>;
 
 			ranges =
@@ -218,6 +219,14 @@ xor11 {
 				};
 			};
 
+			i2c0: i2c@11000 {
+				reg = <0x11000 0x20>;
+			};
+
+			i2c1: i2c@11100 {
+				reg = <0x11100 0x20>;
+			};
+
 			usb@50000 {
 				clocks = <&coreclk 0>;
 			};

arch/arm/boot/dts/armada-xp-matrix.dts

+/*
+ * Device Tree file for Marvell Armada XP Matrix board
+ *
+ * Copyright (C) 2013 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "armada-xp-mv78460.dtsi"
+
+/ {
+	model = "Marvell Armada XP Matrix Board";
+	compatible = "marvell,axp-matrix", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x00000000 0 0x80000000>; /* 2 GB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
+
+		internal-regs {
+			serial@12000 {
+				clock-frequency = <250000000>;
+				status = "okay";
+			};
+			serial@12100 {
+				clock-frequency = <250000000>;
+				status = "okay";
+			};
+			serial@12200 {
+				clock-frequency = <250000000>;
+				status = "okay";
+			};
+			serial@12300 {
+				clock-frequency = <250000000>;
+				status = "okay";
+			};
+
+			sata@a0000 {
+				nr-ports = <2>;
+				status = "okay";
+			};
+
+			ethernet@30000 {
+				status = "okay";
+				phy-mode = "sgmii";
+			};
+
+			pcie-controller {
+				status = "okay";
+
+				pcie@1,0 {
+					/* Port 0, Lane 0 */
+					status = "okay";
+				};
+			};
+
+			usb@50000 {
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/armada-xp-mv78230.dtsi

@@ -57,6 +57,7 @@ pcie-controller {
 			#address-cells = <3>;
 			#size-cells = <2>;
 
+			msi-parent = <&mpic>;
 			bus-range = <0x00 0xff>;
 
 			ranges =

arch/arm/boot/dts/armada-xp-mv78260.dtsi

@@ -58,6 +58,7 @@ pcie-controller {
 			#address-cells = <3>;
 			#size-cells = <2>;
 
+			msi-parent = <&mpic>;
 			bus-range = <0x00 0xff>;
 
 			ranges =

arch/arm/boot/dts/armada-xp-mv78460.dtsi

@@ -74,6 +74,7 @@ pcie-controller {
 			#address-cells = <3>;
 			#size-cells = <2>;
 
+			msi-parent = <&mpic>;
 			bus-range = <0x00 0xff>;
 
 			ranges =

arch/arm/boot/dts/armada-xp.dtsi

@@ -147,6 +147,16 @@ xor01 {
 				};
 			};
 
+			i2c0: i2c@11000 {
+				compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
+				reg = <0x11000 0x100>;
+			};
+
+			i2c1: i2c@11100 {
+				compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
+				reg = <0x11100 0x100>;
+			};
+
 			usb@50000 {
 				clocks = <&gateclk 18>;
 			};

arch/arm/boot/dts/at91sam9g20ek_common.dtsi

@@ -96,7 +96,6 @@ ssc0: ssc@fffbc000 {
 			};
 
 			spi0: spi@fffc8000 {
-				status = "okay";
 				cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
 				mtd_dataflash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";

arch/arm/boot/dts/at91sam9n12.dtsi

@@ -437,6 +437,9 @@ ssc0: ssc@f0010000 {
 				compatible = "atmel,at91sam9g45-ssc";
 				reg = <0xf0010000 0x4000>;
 				interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+				dmas = <&dma 0 AT91_DMA_CFG_PER_ID(21)>,
+				       <&dma 0 AT91_DMA_CFG_PER_ID(22)>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
 				status = "disabled";

arch/arm/boot/dts/at91sam9n12ek.dts

@@ -38,9 +38,18 @@ dbgu: serial@fffff200 {
 				status = "okay";
 			};
 
+			ssc0: ssc@f0010000 {
+				status = "okay";
+			};
+
 			i2c0: i2c@f8010000 {
 				status = "okay";
 
+				wm8904: codec@1a {
+					compatible = "wm8904";
+					reg = <0x1a>;
+				};
+
 				qt1070: keyboard@1b {
 					compatible = "qt1070";
 					reg = <0x1b>;
@@ -82,6 +91,13 @@ pinctrl_qt1070_irq: qt1070_irq {
 							<AT91_PIOA 2 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
 					};
 				};
+
+				sound {
+					pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
+						atmel,pins =
+							<AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+					};
+				};
 			};
 
 			spi0: spi@f0000000 {
@@ -142,4 +158,22 @@ enter {
 			gpio-key,wakeup;
 		};
 	};
+
+	sound {
+		compatible = "atmel,asoc-wm8904";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
+
+		atmel,model = "wm8904 @ AT91SAM9N12";
+		atmel,audio-routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"IN2L", "Line In Jack",
+			"IN2R", "Line In Jack",
+			"Mic", "MICBIAS",
+			"IN1L", "Mic";
+
+		atmel,ssc-controller = <&ssc0>;
+		atmel,audio-codec = <&wm8904>;
+	};
 };

arch/arm/boot/dts/atlas6.dtsi

@@ -65,6 +65,11 @@ rsc-controller@88020000 {
 				compatible = "sirf,prima2-rsc";
 				reg = <0x88020000 0x1000>;
 			};
+
+			cphifbg@88030000 {
+				compatible = "sirf,prima2-cphifbg";
+				reg = <0x88030000 0x1000>;
+			};
 		};
 
 		mem-iobg {
@@ -75,10 +80,17 @@ mem-iobg {
 
 			memory-controller@90000000 {
 				compatible = "sirf,prima2-memc";
-				reg = <0x90000000 0x10000>;
+				reg = <0x90000000 0x2000>;
 				interrupts = <27>;
 				clocks = <&clks 5>;
 			};
+
+			memc-monitor {
+				compatible = "sirf,prima2-memcmon";
+				reg = <0x90002000 0x200>;
+				interrupts = <4>;
+				clocks = <&clks 32>;
+			};
 		};
 
 		disp-iobg {
@@ -120,6 +132,20 @@ graphics@98000000 {
 			};
 		};
 
+		graphics2d-iobg {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0xa0000000 0xa0000000 0x8000000>;
+
+			ble@a0000000 {
+				compatible = "sirf,atlas6-ble";
+				reg = <0xa0000000 0x2000>;
+				interrupts = <5>;
+				clocks = <&clks 33>;
+			};
+		};
+
 		dsp-iobg {
 			compatible = "simple-bus";
 			#address-cells = <1>;
@@ -271,6 +297,11 @@ spi1: spi@b0170000 {
 				compatible = "sirf,prima2-spi";
 				reg = <0xb0170000 0x10000>;
 				interrupts = <16>;
+				sirf,spi-num-chipselects = <1>;
+				sirf,spi-dma-rx-channel = <12>;
+				sirf,spi-dma-tx-channel = <13>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				clocks = <&clks 20>;
 				status = "disabled";
 			};

arch/arm/boot/dts/bcm11351-brt.dts

@@ -40,6 +40,7 @@ sdio2: sdio@3f190000 {
 
 	sdio4: sdio@3f1b0000 {
 		max-frequency = <48000000>;
+		cd-gpios = <&gpio 14 0>;
 		status = "okay";
 	};
 

arch/arm/boot/dts/bcm11351.dtsi

@@ -49,6 +49,36 @@ uart@3e000000 {
 		reg-io-width = <4>;
 	};
 
+	uart@3e001000 {
+		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
+		status = "disabled";
+		reg = <0x3e001000 0x1000>;
+		clock-frequency = <13000000>;
+		interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+	};
+
+	uart@3e002000 {
+		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
+		status = "disabled";
+		reg = <0x3e002000 0x1000>;
+		clock-frequency = <13000000>;
+		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+	};
+
+	uart@3e003000 {
+		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
+		status = "disabled";
+		reg = <0x3e003000 0x1000>;
+		clock-frequency = <13000000>;
+		interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+	};
+
 	L2: l2-cache {
 		compatible = "brcm,bcm11351-a2-pl310-cache";
 		reg = <0x3ff20000 0x1000>;
@@ -68,31 +98,47 @@ timer@35006000 {
 		clock-frequency = <32768>;
 	};
 
+	gpio: gpio@35003000 {
+		compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
+		reg = <0x35003000 0x800>;
+		interrupts =
+		       <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+	};
+
 	sdio1: sdio@3f180000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f180000 0x10000>;
-		interrupts = <0x0 77 0x4>;
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 		status = "disabled";
 	};
 
 	sdio2: sdio@3f190000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f190000 0x10000>;
-		interrupts = <0x0 76 0x4>;
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 		status = "disabled";
 	};
 
 	sdio3: sdio@3f1a0000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1a0000 0x10000>;
-		interrupts = <0x0 74 0x4>;
+		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 		status = "disabled";
 	};
 
 	sdio4: sdio@3f1b0000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1b0000 0x10000>;
-		interrupts = <0x0 73 0x4>;
+		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 		status = "disabled";
 	};
 

arch/arm/boot/dts/bcm28155-ap.dts

@@ -40,6 +40,7 @@ sdio2: sdio@3f190000 {
 
 	sdio4: sdio@3f1b0000 {
 		max-frequency = <48000000>;
+		cd-gpios = <&gpio 14 0>;
 		status = "okay";
 	};
 };

arch/arm/boot/dts/dove-cm-a510.dts

 /dts-v1/;
 
-/include/ "dove.dtsi"
+#include "dove.dtsi"
 
 / {
 	model = "Compulab CM-A510";

arch/arm/boot/dts/dove-cubox.dts

 /dts-v1/;
 
-/include/ "dove.dtsi"
+#include "dove.dtsi"
 
 / {
 	model = "SolidRun CuBox";
@@ -99,18 +99,12 @@ clkout0 {
 			silabs,pll-master;
 		};
 
-		clkout1 {
-			reg = <1>;
-			silabs,drive-strength = <8>;
-			silabs,multisynth-source = <1>;
-			silabs,clock-source = <0>;
-			silabs,pll-master;
-		};
-
 		clkout2 {
 			reg = <2>;
+			silabs,drive-strength = <8>;
 			silabs,multisynth-source = <1>;
 			silabs,clock-source = <0>;
+			silabs,pll-master;
 		};
 	};
 };
@@ -132,3 +126,11 @@ spi-flash@0 {
 		reg = <0>;
 	};
 };
+
+&audio1 {
+	status = "okay";
+	clocks = <&gate_clk 13>, <&si5351 2>;
+	clock-names = "internal", "extclk";
+	pinctrl-0 = <&pmx_audio1_i2s1_spdifo &pmx_audio1_extclk>;
+	pinctrl-names = "default";
+};

arch/arm/boot/dts/dove-d2plug.dts

 /dts-v1/;
 
-/include/ "dove.dtsi"
+#include "dove.dtsi"
 
 / {
 	model = "Globalscale D2Plug";

arch/arm/boot/dts/dove-d3plug.dts

+/dts-v1/;
+
+#include "dove.dtsi"
+
+/ {
+	model = "Globalscale D3Plug";
+	compatible = "globalscale,d3plug", "marvell,dove";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p2 rw rootwait";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>;
+		pinctrl-names = "default";
+
+		wlan-act {
+			label = "wlan-act";
+			gpios = <&gpio0 0 1>;
+		};
+
+		wlan-ap {
+			label = "wlan-ap";
+			gpios = <&gpio0 1 1>;
+		};
+
+		status {
+			label = "status";
+			gpios = <&gpio0 2 1>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usb_power: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 8 0>;
+			pinctrl-0 = <&pmx_gpio_8>;
+			pinctrl-names = "default";
+		};
+	};
+};
+
+&uart0 { status = "okay"; };
+&sata0 { status = "okay"; };
+&i2c0 { status = "okay"; };
+
+/* Samsung M8G2F eMMC */
+&sdio0 {
+	status = "okay";
+	non-removable;
+	bus-width = <4>;
+};
+
+/* Marvell SD8787 WLAN/BT */
+&sdio1 {
+	status = "okay";
+	non-removable;
+};
+
+&spi0 {
+	status = "okay";
+
+	/* spi0.0: 2M Flash Macronix MX25L1605D */
+	spi-flash@0 {
+		compatible = "st,m25l1605d";
+		spi-max-frequency = <86000000>;
+		reg = <0>;
+	};
+};
+
+&pcie {
+	status = "okay";
+	/* Fresco Logic USB3.0 xHCI controller */
+	pcie-port@0 {
+		status = "okay";
+		reset-gpios = <&gpio0 26 1>;
+		reset-delay-us = <20000>;
+		pinctrl-0 = <&pmx_camera_gpio>;
+		pinctrl-names = "default";
+	};
+	/* Mini-PCIe slot */
+	pcie-port@1 {
+		status = "okay";
+		reset-gpios = <&gpio0 25 1>;
+	};
+};

arch/arm/boot/dts/dove-dove-db.dts

 /dts-v1/;
 
-/include/ "dove.dtsi"
+#include "dove.dtsi"
 
 / {
 	model = "Marvell DB-MV88AP510-BP Development Board";

arch/arm/boot/dts/dove.dtsi

 /include/ "skeleton.dtsi"
 
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
 / {
 	compatible = "marvell,dove";
 	model = "Marvell Armada 88AP510 SoC";
+	interrupt-parent = <&intc>;
 
 	aliases {
 		gpio0 = &gpio0;
@@ -27,20 +30,87 @@ l2: l2-cache {
 		marvell,tauros2-cache-features = <0>;
 	};
 
-	soc@f1000000 {
+	mbus {
+		compatible = "marvell,dove-mbus", "marvell,mbus", "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		controller = <&mbusc>;
+		pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256M MEM space */
+		pcie-io-aperture  = <0xf2000000 0x00200000>; /*   2M I/O space */
+
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x0100000   /* MBUS regs  1M */
+			  MBUS_ID(0xf0, 0x02) 0 0xf1800000 0x1000000   /* AXI  regs 16M */
+			  MBUS_ID(0x01, 0xfd) 0 0xf8000000 0x8000000   /* BootROM  128M */
+			  MBUS_ID(0x03, 0x01) 0 0xc8000000 0x0100000   /* CESA SRAM  1M */
+			  MBUS_ID(0x0d, 0x00) 0 0xf0000000 0x0100000>; /* PMU  SRAM  1M */
+
+		pcie: pcie-controller {
+			compatible = "marvell,dove-pcie";
+			status = "disabled";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&intc>;
+			bus-range = <0x00 0xff>;
+
+			ranges = <0x82000000 0x0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x2000
+			          0x82000000 0x0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x2000
+				  0x82000000 0x1 0x0 MBUS_ID(0x04, 0xe8) 0 1 0   /* Port 0.0 Mem */
+				  0x81000000 0x1 0x0 MBUS_ID(0x04, 0xe0) 0 1 0   /* Port 0.0 I/O */
+				  0x82000000 0x2 0x0 MBUS_ID(0x08, 0xe8) 0 1 0   /* Port 1.0 Mem */
+				  0x81000000 0x2 0x0 MBUS_ID(0x08, 0xe0) 0 1 0>; /* Port 1.0 I/O */
+
+			pcie-port@0 {
+				device_type = "pci";
+				status = "disabled";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				clocks = <&gate_clk 4>;
+				marvell,pcie-port = <0>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+				          0x81000000 0 0 0x81000000 0x1 0 1 0>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &intc 16>;
+			};
+
+			pcie-port@1 {
+				device_type = "pci";
+				status = "disabled";
+				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				clocks = <&gate_clk 5>;
+				marvell,pcie-port = <1>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+				          0x81000000 0 0 0x81000000 0x2 0 1 0>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &intc 18>;
+			};
+		};
+
+		internal-regs {
 			compatible = "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
-		interrupt-parent = <&intc>;
+			ranges = <0x00000000 MBUS_ID(0xf0, 0x01) 0 0x0100000   /* MBUS regs  1M */
+				  0x00800000 MBUS_ID(0xf0, 0x02) 0 0x1000000   /* AXI  regs 16M */
+				  0xffffe000 MBUS_ID(0x03, 0x01) 0 0x0000800   /* CESA SRAM  2k */
+				  0xfffff000 MBUS_ID(0x0d, 0x00) 0 0x0000800>; /* PMU  SRAM  2k */
 
-		ranges = <0xc8000000 0xc8000000 0x0100000   /* CESA SRAM   1M */
-		          0xe0000000 0xe0000000 0x8000000   /* PCIe0 Mem 128M */
-		          0xe8000000 0xe8000000 0x8000000   /* PCIe1 Mem 128M */
-		          0xf0000000 0xf0000000 0x0100000   /* ScratchPad  1M */
-		          0x00000000 0xf1000000 0x1000000   /* SB/NB regs 16M */
-		          0xf2000000 0xf2000000 0x0100000   /* PCIe0 I/O   1M */
-		          0xf2100000 0xf2100000 0x0100000   /* PCIe0 I/O   1M */
-		          0xf8000000 0xf8000000 0x8000000>; /* BootROM   128M */
+			mbusc: mbus-ctrl@20000 {
+				compatible = "marvell,mbus-controller";
+				reg = <0x20000 0x80>, <0x800100 0x8>;
+			};
 
 			timer: timer@20300 {
 				compatible = "marvell,orion-timer";
@@ -227,6 +297,11 @@ pmx_gpio_13: pmx-gpio-13 {
 					marvell,function = "gpio";
 				};
 
+				pmx_audio1_extclk: pmx-audio1-extclk {
+					marvell,pins = "mpp13";
+					marvell,function = "audio1";
+				};
+
 				pmx_gpio_14: pmx-gpio-14 {
 					marvell,pins = "mpp14";
 					marvell,function = "gpio";
@@ -302,6 +377,11 @@ pmx_audio1_gpio: pmx-audio1-gpio {
 					marvell,function = "gpio";
 				};
 
+				pmx_audio1_i2s1_spdifo: pmx-audio1-i2s1-spdifo {
+					marvell,pins = "mpp_audio1";
+					marvell,function = "i2s1/spdifo";
+				};
+
 				pmx_spi0: pmx-spi0 {
 					marvell,pins = "mpp_spi0";
 					marvell,function = "spi0";
@@ -422,7 +502,7 @@ rtc: real-time-clock@d8500 {
 			crypto: crypto-engine@30000 {
 				compatible = "marvell,orion-crypto";
 				reg = <0x30000 0x10000>,
-			      <0xc8000000 0x800>;
+				      <0xffffe000 0x800>;
 				reg-names = "regs", "sram";
 				interrupts = <31>;
 				clocks = <&gate_clk 15>;
@@ -444,7 +524,6 @@ channel0 {
 
 				channel1 {
 					interrupts = <40>;
-				dmacap,memset;
 					dmacap,memcpy;
 					dmacap,xor;
 				};
@@ -465,7 +544,6 @@ channel0 {
 
 				channel1 {
 					interrupts = <43>;
-				dmacap,memset;
 					dmacap,memcpy;
 					dmacap,xor;
 				};
@@ -486,7 +564,7 @@ ethphy: ethernet-phy {
 				};
 			};
 
-		eth: ethernet-controller@72000 {
+			eth: ethernet-ctrl@72000 {
 				compatible = "marvell,orion-eth";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -505,5 +583,24 @@ ethernet-port@0 {
 					phy-handle = <&ethphy>;
 				};
 			};
+
+			audio0: audio-controller@b0000 {
+				compatible = "marvell,dove-audio";
+				reg = <0xb0000 0x2210>;
+				interrupts = <19>, <20>;
+				clocks = <&gate_clk 12>;
+				clock-names = "internal";
+				status = "disabled";
+			};
+
+			audio1: audio-controller@b4000 {
+				compatible = "marvell,dove-audio";
+				reg = <0xb4000 0x2210>;
+				interrupts = <21>, <22>;
+				clocks = <&gate_clk 13>;
+				clock-names = "internal";
+				status = "disabled";
+			};
+		};
 	};
 };

arch/arm/boot/dts/exynos4.dtsi

@@ -49,6 +49,12 @@ chipid@10000000 {
 		reg = <0x10000000 0x100>;
 	};
 
+	mipi_phy: video-phy@10020710 {
+		compatible = "samsung,s5pv210-mipi-video-phy";
+		reg = <0x10020710 8>;
+		#phy-cells = <1>;
+	};
+
 	pd_mfc: mfc-power-domain@10023C40 {
 		compatible = "samsung,exynos4210-pd";
 		reg = <0x10023C40 0x20>;
@@ -161,6 +167,8 @@ csis_0: csis@11880000 {
 			clock-names = "csis", "sclk_csis";
 			bus-width = <4>;
 			samsung,power-domain = <&pd_cam>;
+			phys = <&mipi_phy 0>;
+			phy-names = "csis";
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -174,6 +182,8 @@ csis_1: csis@11890000 {
 			clock-names = "csis", "sclk_csis";
 			bus-width = <2>;
 			samsung,power-domain = <&pd_cam>;
+			phys = <&mipi_phy 2>;
+			phy-names = "csis";
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;

arch/arm/boot/dts/exynos4210-origen.dts

@@ -32,14 +32,21 @@ chosen {
 		bootargs ="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC2,115200 init=/linuxrc";
 	};
 
-	mmc_reg: voltage-regulator {
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mmc_reg: regulator@0 {
 			compatible = "regulator-fixed";
+			reg = <0>;
 			regulator-name = "VMEM_VDD_2.8V";
 			regulator-min-microvolt = <2800000>;
 			regulator-max-microvolt = <2800000>;
 			gpio = <&gpx1 1 0>;
 			enable-active-high;
 		};
+	};
 
 	tmu@100C0000 {
 		status = "okay";

arch/arm/boot/dts/exynos5250-smdk5250.dts

@@ -231,14 +231,6 @@ i2s0: i2s@03830000 {
 		status = "okay";
 	};
 
-	i2s1: i2s@12D60000 {
-		status = "disabled";
-	};
-
-	i2s2: i2s@12D70000 {
-		status = "disabled";
-	};
-
 	sound {
 		compatible = "samsung,smdk-wm8994";