Commit fc3359b9 authored by Arnd Bergmann's avatar Arnd Bergmann

Merge tag 'v4.5-rockchip-dts64-1' of...

Merge tag 'v4.5-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64

Merge "rockchip dts64 changes for 4.5" from Heiko Stuebner:

First round of 64bit devicetree changes for Rockchip socs.
This includes support for the evaluation board of the rk3368
as well as the dts-part for the newly added thermal management
support, rk3368 pwm nodes and an alias.

* tag 'v4.5-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  arm64: dts: rockchip: add rk3368 evaluation board
  arm64: dts: rockchip: add the pwm node info for RK3368 SoCs
  arm64: dts: rockchip: Enable the Thermal on R88 board
  arm64: dts: rockchip: Add main thermal info to rk3368.dtsi
  arm64: dts: rockchip: Add the thermal data found on RK3368
  arm64: dts: rockchip: Setup rk3368 ethernet0 alias for u-boot
parents 4702d599 5378e28c
......@@ -69,6 +69,10 @@ Rockchip platforms device tree bindings
"google,veyron-speedy-rev3", "google,veyron-speedy-rev2",
"google,veyron-speedy", "google,veyron", "rockchip,rk3288";
- Rockchip RK3368 evb:
Required root node properties:
- compatible = "rockchip,rk3368-evb-act8846", "rockchip,rk3368";
- Rockchip R88 board:
Required root node properties:
- compatible = "rockchip,r88", "rockchip,rk3368";
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
always := $(dtb-y)
......
/*
* Copyright (c) 2015 Caesar Wang <wxt@rock-chips.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "rk3368-evb.dtsi"
/ {
model = "Rockchip RK3368 EVB with ACT8846 pmic";
compatible = "rockchip,rk3368-evb-act8846", "rockchip,rk3368";
};
&i2c0 {
clock-frequency = <400000>;
vdd_cpu: syr827@40 {
compatible = "silergy,syr827";
reg = <0x40>;
fcs,suspend-voltage-selector = <1>;
regulator-name = "vdd_cpu";
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <&vcc_sys>;
};
vdd_gpu: syr828@41 {
compatible = "silergy,syr828";
reg = <0x41>;
fcs,suspend-voltage-selector = <1>;
regulator-name = "vdd_gpu";
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
vin-supply = <&vcc_sys>;
};
act8846: act8846@5a {
compatible = "active-semi,act8846";
reg = <0x5a>;
status = "okay";
vp1-supply = <&vcc_sys>;
vp2-supply = <&vcc_sys>;
vp3-supply = <&vcc_sys>;
vp4-supply = <&vcc_sys>;
inl1-supply = <&vcc_io>;
inl2-supply = <&vcc_sys>;
inl3-supply = <&vcc_20>;
regulators {
vcc_ddr: REG1 {
regulator-name = "VCC_DDR";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
};
vcc_io: REG2 {
regulator-name = "VCC_IO";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdd_log: REG3 {
regulator-name = "VDD_LOG";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
};
vcc_20: REG4 {
regulator-name = "VCC_20";
regulator-min-microvolt = <2000000>;
regulator-max-microvolt = <2000000>;
regulator-always-on;
};
vccio_sd: REG5 {
regulator-name = "VCCIO_SD";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdd10_lcd: REG6 {
regulator-name = "VDD10_LCD";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
};
vcca_codec: REG7 {
regulator-name = "VCCA_CODEC";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vcca_tp: REG8 {
regulator-name = "VCCA_TP";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vccio_pmu: REG9 {
regulator-name = "VCCIO_PMU";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdd_10: REG10 {
regulator-name = "VDD_10";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
};
vcc_18: REG11 {
regulator-name = "VCC_18";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
vcc18_lcd: REG12 {
regulator-name = "VCC18_LCD";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
};
};
};
/*
* Copyright (c) 2015 Caesar Wang <wxt@rock-chips.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include <dt-bindings/pwm/pwm.h>
#include "rk3368.dtsi"
/ {
chosen {
stdout-path = "serial2:115200n8";
};
memory {
device_type = "memory";
reg = <0x0 0x0 0x0 0x40000000>;
};
backlight: backlight {
compatible = "pwm-backlight";
brightness-levels = <
0 1 2 3 4 5 6 7
8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23
24 25 26 27 28 29 30 31
32 33 34 35 36 37 38 39
40 41 42 43 44 45 46 47
48 49 50 51 52 53 54 55
56 57 58 59 60 61 62 63
64 65 66 67 68 69 70 71
72 73 74 75 76 77 78 79
80 81 82 83 84 85 86 87
88 89 90 91 92 93 94 95
96 97 98 99 100 101 102 103
104 105 106 107 108 109 110 111
112 113 114 115 116 117 118 119
120 121 122 123 124 125 126 127
128 129 130 131 132 133 134 135
136 137 138 139 140 141 142 143
144 145 146 147 148 149 150 151
152 153 154 155 156 157 158 159
160 161 162 163 164 165 166 167
168 169 170 171 172 173 174 175
176 177 178 179 180 181 182 183
184 185 186 187 188 189 190 191
192 193 194 195 196 197 198 199
200 201 202 203 204 205 206 207
208 209 210 211 212 213 214 215
216 217 218 219 220 221 222 223
224 225 226 227 228 229 230 231
232 233 234 235 236 237 238 239
240 241 242 243 244 245 246 247
248 249 250 251 252 253 254 255>;
default-brightness-level = <128>;
enable-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&bl_en>;
pwms = <&pwm0 0 1000000 PWM_POLARITY_INVERTED>;
pwm-delay-us = <10000>;
};
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
pinctrl-0 = <&emmc_reset>;
pinctrl-names = "default";
reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
};
keys: gpio-keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&pwr_key>;
button@0 {
gpio-key,wakeup = <1>;
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
label = "GPIO Power";
linux,code = <116>;
};
};
/* supplies both host and otg */
vcc_host: vcc-host-regulator {
compatible = "regulator-fixed";
enable-active-high;
gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&host_vbus_drv>;
regulator-name = "vcc_host";
regulator-always-on;
regulator-boot-on;
vin-supply = <&vcc_sys>;
};
vcc_lan: vcc-lan-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_lan";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <&vcc_io>;
};
vcc_sys: vcc-sys-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
regulator-boot-on;
};
};
&emmc {
broken-cd;
bus-width = <8>;
cap-mmc-highspeed;
disable-wp;
mmc-pwrseq = <&emmc_pwrseq>;
non-removable;
num-slots = <1>;
pinctrl-names = "default";
pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
status = "okay";
};
&gmac {
phy-supply = <&vcc_lan>;
phy-mode = "rmii";
clock_in_out = "output";
snps,reset-gpio = <&gpio3 12 0>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 1000000>;
pinctrl-names = "default";
pinctrl-0 = <&rmii_pins>;
tx_delay = <0x30>;
rx_delay = <0x10>;
status = "ok";
};
&i2c0 {
status = "okay";
};
&pinctrl {
pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
bias-disable;
drive-strength = <8>;
};
pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
bias-pull-up;
drive-strength = <8>;
};
backlight {
bl_en: bl-en {
rockchip,pins = <0 20 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
emmc {
emmc_bus8: emmc-bus8 {
rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
<1 19 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
<1 20 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
<1 21 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
<1 22 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
<1 23 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
<1 24 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
<1 25 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
};
emmc-clk {
rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
};
emmc-cmd {
rockchip,pins = <1 26 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
};
emmc_reset: emmc-reset {
rockchip,pins = <2 3 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
keys {
pwr_key: pwr-key {
rockchip,pins = <0 2 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
pmic {
pmic_int: pmic-int {
rockchip,pins = <0 1 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
sdio {
wifi_reg_on: wifi-reg-on {
rockchip,pins = <3 4 RK_FUNC_GPIO &pcfg_pull_none>;
};
bt_rst: bt-rst {
rockchip,pins = <3 5 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
usb {
host_vbus_drv: host-vbus-drv {
rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
};
&pwm0 {
status = "okay";
};
&tsadc {
rockchip,hw-tshut-mode = <0>; /* tshut mode 0:CRU 1:GPIO */
rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
status = "okay";
};
&uart2 {
status = "okay";
};
&usb_host0_ehci {
status = "okay";
};
&usb_otg {
dr_mode = "host";
status = "okay";
};
&wdt {
status = "okay";
};
......@@ -336,6 +336,12 @@ &saradc {
status = "okay";
};
&tsadc {
rockchip,hw-tshut-mode = <0>; /* tshut mode 0:CRU 1:GPIO */
rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
status = "okay";
};
&uart2 {
status = "okay";
};
......
/*
* Device Tree Source for RK3368 SoC thermal
*
* Copyright (c) 2015, Fuzhou Rockchip Electronics Co., Ltd
* Caesar Wang <wxt@rock-chips.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include <dt-bindings/thermal/thermal.h>
cpu_thermal: cpu_thermal {
polling-delay-passive = <100>; /* milliseconds */
polling-delay = <5000>; /* milliseconds */
thermal-sensors = <&tsadc 0>;
trips {
cpu_alert0: cpu_alert0 {
temperature = <75000>; /* millicelsius */
hysteresis = <2000>; /* millicelsius */
type = "passive";
};
cpu_alert1: cpu_alert1 {
temperature = <80000>; /* millicelsius */
hysteresis = <2000>; /* millicelsius */
type = "passive";
};
cpu_crit: cpu_crit {
temperature = <95000>; /* millicelsius */
hysteresis = <2000>; /* millicelsius */
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&cpu_alert0>;
cooling-device =
<&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu_alert1>;
cooling-device =
<&cpu_l0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
gpu_thermal: gpu_thermal {
polling-delay-passive = <100>; /* milliseconds */
polling-delay = <5000>; /* milliseconds */
thermal-sensors = <&tsadc 1>;
trips {
gpu_alert0: gpu_alert0 {
temperature = <80000>; /* millicelsius */
hysteresis = <2000>; /* millicelsius */
type = "passive";
};
gpu_crit: gpu_crit {
temperature = <1150000>; /* millicelsius */
hysteresis = <2000>; /* millicelsius */
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&gpu_alert0>;
cooling-device =
<&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
......@@ -45,6 +45,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/rockchip.h>
#include <dt-bindings/thermal/thermal.h>
/ {
compatible = "rockchip,rk3368";
......@@ -53,6 +54,7 @@ / {
#size-cells = <2>;
aliases {
ethernet0 = &gmac;
i2c0 = &i2c0;
i2c1 = &i2c1;
i2c2 = &i2c2;
......@@ -123,6 +125,8 @@ cpu_l0: cpu@0 {
reg = <0x0 0x0>;
cpu-idle-states = <&cpu_sleep>;
enable-method = "psci";
#cooling-cells = <2>; /* min followed by max */
};
cpu_l1: cpu@1 {
......@@ -155,6 +159,8 @@ cpu_b0: cpu@100 {
reg = <0x0 0x100>;
cpu-idle-states = <&cpu_sleep>;
enable-method = "psci";
#cooling-cells = <2>; /* min followed by max */
};
cpu_b1: cpu@101 {
......@@ -404,6 +410,27 @@ uart4: serial@ff1c0000 {
status = "disabled";
};
thermal-zones {
#include "rk3368-thermal.dtsi"
};
tsadc: tsadc@ff280000 {
compatible = "rockchip,rk3368-tsadc";
reg = <0x0 0xff280000 0x0 0x100>;
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
clock-names = "tsadc", "apb_pclk";
resets = <&cru SRST_TSADC>;
reset-names = "tsadc-apb";
pinctrl-names = "init", "default", "sleep";
pinctrl-0 = <&otp_gpio>;
pinctrl-1 = <&otp_out>;
pinctrl-2 = <&otp_gpio>;
#thermal-sensor-cells = <1>;
rockchip,hw-tshut-temp = <95000>;
status = "disabled";
};
gmac: ethernet@ff290000 {
compatible = "rockchip,rk3368-gmac";
reg = <0x0 0xff290000 0x0 0x10000>;
......@@ -471,6 +498,48 @@ i2c2: i2c@ff660000 {
status = "disabled";
};
pwm0: pwm@ff680000 {
compatible = "rockchip,rk3368-pwm", "rockchip,rk3288-pwm";
reg = <0x0 0xff680000 0x0 0x10>;
#pwm-cells = <3>;
pinctrl-names = "default";
pinctrl-0 = <&pwm0_pin>;
clocks = <&cru PCLK_PWM1>;
clock-names = "pwm";
status = "disabled";
};
pwm1: pwm@ff680010 {
compatible = "rockchip,rk3368-pwm", "rockchip,rk3288-pwm";
reg = <0x0 0xff680010 0x0 0x10>;
#pwm-cells = <3>;
pinctrl-names = "default";
pinctrl-0 = <&pwm1_pin>;
clocks = <&cru PCLK_PWM1>;
clock-names = "pwm";
status = "disabled";
};
pwm2: pwm@ff680020 {
compatible = "rockchip,rk3368-pwm", "rockchip,rk3288-pwm";
reg = <0x0 0xff680020 0x0 0x10>;
#pwm-cells = <3>;
clocks = <&cru PCLK_PWM1>;
clock-names = "pwm";
status = "disabled";
};
pwm3: pwm@ff680030 {
compatible = "rockchip,rk3368-pwm", "rockchip,rk3288-pwm";
reg = <0x0 0xff680030 0x0 0x10>;
#pwm-cells = <3>;
pinctrl-names = "default";
pinctrl-0 = <&pwm3_pin>;
clocks = <&cru PCLK_PWM1>;
clock-names = "pwm";
status = "disabled";
};
uart2: serial@ff690000 {
compatible = "rockchip,rk3368-uart", "snps,dw-apb-uart";
reg = <0x0 0xff690000 0x0 0x100>;
......@@ -712,6 +781,24 @@ i2c5_xfer: i2c5-xfer {
};
};
pwm0 {
pwm0_pin: pwm0-pin {
rockchip,pins = <3 8 RK_FUNC_2 &pcfg_pull_none>;
};
};
pwm1 {
pwm1_pin: pwm1-pin {
rockchip,pins = <0 8 RK_FUNC_2 &pcfg_pull_none>;
};
};
pwm3 {
pwm3_pin: pwm3-pin {
rockchip,pins = <3 29 RK_FUNC_3 &pcfg_pull_none>;
};
};
sdio0 {
sdio0_bus1: sdio0-bus1 {
rockchip,pins = <2 28 RK_FUNC_1 &pcfg_pull_up>;
......@@ -829,6 +916,16 @@ spi2_tx: spi2-tx {
};
};
tsadc {
otp_gpio: otp-gpio {
rockchip,pins = <0 10 RK_FUNC_GPIO &pcfg_pull_none>;
};
otp_out: otp-out {
rockchip,pins = <0 10 RK_FUNC_1 &pcfg_pull_none>;
};
};
uart0 {
uart0_xfer: uart0-xfer {
rockchip,pins = <2 24 RK_FUNC_1 &pcfg_pull_up>,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment