Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (82 commits)
  [PATCH] pata_ali: small fixes
  [PATCH] pata_via: VIA 8251 bridged systems are now out and about
  [PATCH] trivial piix: swap bogus dot for comma space
  [PATCH] sata_promise: PHYMODE4 fixup
  [PATCH] libata: always use polling IDENTIFY
  [libata] pata_cs5535: fix build
  [PATCH] ahci: do not powerdown during initialization
  [PATCH] libata: prepare ata_sg_clean() for invocation from EH
  [PATCH] libata: separate out rw ATA taskfile building into ata_build_rw_tf()
  [PATCH] libata: implement ata_exec_internal_sg()
  [PATCH] libata: make sure IRQ is cleared after ata_bmdma_freeze()
  [PATCH] libata: move BMDMA host status recording from EH to interrupt handler
  [PATCH] libata: make sure sdev doesn't go away while rescanning
  [PATCH] libata: don't request sense if the port is frozen
  [PATCH] libata: fix READ CAPACITY simulation
  [PATCH] libata: implement ATA_FLAG_SETXFER_POLLING and use it in pata_via, take #2
  [PATCH] libata: set IRQF_SHARED for legacy PCI IDE IRQs
  [PATCH] libata: remove unused HSM_ST_UNKNOWN
  [PATCH] libata: kill unnecessary sht->max_sectors initializations
  [PATCH] libata: add missing sht->slave_destroy
  ...

drivers/ata/Kconfig

@@ -328,6 +328,15 @@ config PATA_TRIFLEX
 
 	  If unsure, say N.
 
+config PATA_MARVELL
+	tristate "Marvell PATA support via legacy mode"
+	depends on PCI
+	help
+	  This option enables limited support for the Marvell 88SE6145 ATA
+	  controller.
+
+	  If unsure, say N.
+
 config PATA_MPIIX
 	tristate "Intel PATA MPIIX support"
 	depends on PCI
@@ -483,6 +492,32 @@ config PATA_WINBOND
 
 	  If unsure, say N.
 
+config PATA_WINBOND_VLB
+	tristate "Winbond W83759A VLB PATA support (Experimental)"
+	depends on ISA && EXPERIMENTAL
+	help
+	  Support for the Winbond W83759A controller on Vesa Local Bus
+	  systems.
+
+config PATA_PLATFORM
+	tristate "Generic platform device PATA support"
+	depends on EMBEDDED
+	help
+	  This option enables support for generic directly connected ATA
+	  devices commonly found on embedded systems.
+
+	  If unsure, say N.
+
+config PATA_IXP4XX_CF
+	tristate "IXP4XX Compact Flash support"
+	depends on ARCH_IXP4XX
+	help
+	  This option enables support for a Compact Flash connected on
+	  the ixp4xx expansion bus. This driver had been written for
+	  Loft/Avila boards in mind but can work with others.
+
+	  If unsure, say N.
+
 endif
 endmenu
 

drivers/ata/Makefile

@@ -38,6 +38,7 @@ obj-$(CONFIG_PATA_NETCELL)	+= pata_netcell.o
 obj-$(CONFIG_PATA_NS87410)	+= pata_ns87410.o
 obj-$(CONFIG_PATA_OPTI)		+= pata_opti.o
 obj-$(CONFIG_PATA_OPTIDMA)	+= pata_optidma.o
+obj-$(CONFIG_PATA_MARVELL)	+= pata_marvell.o
 obj-$(CONFIG_PATA_MPIIX)	+= pata_mpiix.o
 obj-$(CONFIG_PATA_OLDPIIX)	+= pata_oldpiix.o
 obj-$(CONFIG_PATA_PCMCIA)	+= pata_pcmcia.o
@@ -51,8 +52,11 @@ obj-$(CONFIG_PATA_SERVERWORKS)	+= pata_serverworks.o
 obj-$(CONFIG_PATA_SIL680)	+= pata_sil680.o
 obj-$(CONFIG_PATA_VIA)		+= pata_via.o
 obj-$(CONFIG_PATA_WINBOND)	+= pata_sl82c105.o
+obj-$(CONFIG_PATA_WINBOND_VLB)	+= pata_winbond.o
 obj-$(CONFIG_PATA_SIS)		+= pata_sis.o
 obj-$(CONFIG_PATA_TRIFLEX)	+= pata_triflex.o
+obj-$(CONFIG_PATA_IXP4XX_CF)	+= pata_ixp4xx_cf.o
+obj-$(CONFIG_PATA_PLATFORM)	+= pata_platform.o
 # Should be last but one libata driver
 obj-$(CONFIG_ATA_GENERIC)	+= ata_generic.o
 # Should be last libata driver

drivers/ata/ata_generic.c

@@ -26,7 +26,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "ata_generic"
-#define DRV_VERSION "0.2.6"
+#define DRV_VERSION "0.2.10"
 
 /*
  *	A generic parallel ATA driver using libata
@@ -109,7 +109,6 @@ static struct scsi_host_template generic_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -118,6 +117,8 @@ static struct scsi_host_template generic_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations generic_port_ops = {
@@ -226,12 +227,14 @@ static struct pci_driver ata_generic_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= ata_generic,
 	.probe 		= ata_generic_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= ata_pci_device_resume,
 };
 
 static int __init ata_generic_init(void)
 {
-	return pci_module_init(&ata_generic_pci_driver);
+	return pci_register_driver(&ata_generic_pci_driver);
 }
 
 

drivers/ata/libata-eh.c

@@ -1136,19 +1136,21 @@ static unsigned int ata_eh_analyze_tf(struct ata_queued_cmd *qc,
 		break;
 
 	case ATA_DEV_ATAPI:
-		tmp = atapi_eh_request_sense(qc->dev,
-					     qc->scsicmd->sense_buffer);
-		if (!tmp) {
-			/* ATA_QCFLAG_SENSE_VALID is used to tell
-			 * atapi_qc_complete() that sense data is
-			 * already valid.
-			 *
-			 * TODO: interpret sense data and set
-			 * appropriate err_mask.
-			 */
-			qc->flags |= ATA_QCFLAG_SENSE_VALID;
-		} else
-			qc->err_mask |= tmp;
+		if (!(qc->ap->pflags & ATA_PFLAG_FROZEN)) {
+			tmp = atapi_eh_request_sense(qc->dev,
+						     qc->scsicmd->sense_buffer);
+			if (!tmp) {
+				/* ATA_QCFLAG_SENSE_VALID is used to
+				 * tell atapi_qc_complete() that sense
+				 * data is already valid.
+				 *
+				 * TODO: interpret sense data and set
+				 * appropriate err_mask.
+				 */
+				qc->flags |= ATA_QCFLAG_SENSE_VALID;
+			} else
+				qc->err_mask |= tmp;
+		}
 	}
 
 	if (qc->err_mask & (AC_ERR_HSM | AC_ERR_TIMEOUT | AC_ERR_ATA_BUS))
@@ -1433,16 +1435,39 @@ static void ata_eh_report(struct ata_port *ap)
 	}
 
 	for (tag = 0; tag < ATA_MAX_QUEUE; tag++) {
+		static const char *dma_str[] = {
+			[DMA_BIDIRECTIONAL]	= "bidi",
+			[DMA_TO_DEVICE]		= "out",
+			[DMA_FROM_DEVICE]	= "in",
+			[DMA_NONE]		= "",
+		};
 		struct ata_queued_cmd *qc = __ata_qc_from_tag(ap, tag);
+		struct ata_taskfile *cmd = &qc->tf, *res = &qc->result_tf;
+		unsigned int nbytes;
 
 		if (!(qc->flags & ATA_QCFLAG_FAILED) || !qc->err_mask)
 			continue;
 
-		ata_dev_printk(qc->dev, KERN_ERR, "tag %d cmd 0x%x "
-			       "Emask 0x%x stat 0x%x err 0x%x (%s)\n",
-			       qc->tag, qc->tf.command, qc->err_mask,
-			       qc->result_tf.command, qc->result_tf.feature,
-			       ata_err_string(qc->err_mask));
+		nbytes = qc->nbytes;
+		if (!nbytes)
+			nbytes = qc->nsect << 9;
+
+		ata_dev_printk(qc->dev, KERN_ERR,
+			"cmd %02x/%02x:%02x:%02x:%02x:%02x/%02x:%02x:%02x:%02x:%02x/%02x "
+			"tag %d cdb 0x%x data %u %s\n         "
+			"res %02x/%02x:%02x:%02x:%02x:%02x/%02x:%02x:%02x:%02x:%02x/%02x "
+			"Emask 0x%x (%s)\n",
+			cmd->command, cmd->feature, cmd->nsect,
+			cmd->lbal, cmd->lbam, cmd->lbah,
+			cmd->hob_feature, cmd->hob_nsect,
+			cmd->hob_lbal, cmd->hob_lbam, cmd->hob_lbah,
+			cmd->device, qc->tag, qc->cdb[0], nbytes,
+			dma_str[qc->dma_dir],
+			res->command, res->feature, res->nsect,
+			res->lbal, res->lbam, res->lbah,
+			res->hob_feature, res->hob_nsect,
+			res->hob_lbal, res->hob_lbam, res->hob_lbah,
+			res->device, qc->err_mask, ata_err_string(qc->err_mask));
 	}
 }
 
@@ -1634,11 +1659,14 @@ static int ata_eh_revalidate_and_attach(struct ata_port *ap,
 	DPRINTK("ENTER\n");
 
 	for (i = 0; i < ATA_MAX_DEVICES; i++) {
-		unsigned int action;
+		unsigned int action, readid_flags = 0;
 
 		dev = &ap->device[i];
 		action = ata_eh_dev_action(dev);
 
+		if (ehc->i.flags & ATA_EHI_DID_RESET)
+			readid_flags |= ATA_READID_POSTRESET;
+
 		if (action & ATA_EH_REVALIDATE && ata_dev_ready(dev)) {
 			if (ata_port_offline(ap)) {
 				rc = -EIO;
@@ -1646,13 +1674,17 @@ static int ata_eh_revalidate_and_attach(struct ata_port *ap,
 			}
 
 			ata_eh_about_to_do(ap, dev, ATA_EH_REVALIDATE);
-			rc = ata_dev_revalidate(dev,
-					ehc->i.flags & ATA_EHI_DID_RESET);
+			rc = ata_dev_revalidate(dev, readid_flags);
 			if (rc)
 				break;
 
 			ata_eh_done(ap, dev, ATA_EH_REVALIDATE);
 
+			/* Configuration may have changed, reconfigure
+			 * transfer mode.
+			 */
+			ehc->i.flags |= ATA_EHI_SETMODE;
+
 			/* schedule the scsi_rescan_device() here */
 			queue_work(ata_aux_wq, &(ap->scsi_rescan_task));
 		} else if (dev->class == ATA_DEV_UNKNOWN &&
@@ -1660,18 +1692,35 @@ static int ata_eh_revalidate_and_attach(struct ata_port *ap,
 			   ata_class_enabled(ehc->classes[dev->devno])) {
 			dev->class = ehc->classes[dev->devno];
 
-			rc = ata_dev_read_id(dev, &dev->class, 1, dev->id);
-			if (rc == 0)
-				rc = ata_dev_configure(dev, 1);
+			rc = ata_dev_read_id(dev, &dev->class, readid_flags,
+					     dev->id);
+			if (rc == 0) {
+				ehc->i.flags |= ATA_EHI_PRINTINFO;
+				rc = ata_dev_configure(dev);
+				ehc->i.flags &= ~ATA_EHI_PRINTINFO;
+			} else if (rc == -ENOENT) {
+				/* IDENTIFY was issued to non-existent
+				 * device.  No need to reset.  Just
+				 * thaw and kill the device.
+				 */
+				ata_eh_thaw_port(ap);
+				dev->class = ATA_DEV_UNKNOWN;
+				rc = 0;
+			}
 
 			if (rc) {
 				dev->class = ATA_DEV_UNKNOWN;
 				break;
 			}
 
-			spin_lock_irqsave(ap->lock, flags);
-			ap->pflags |= ATA_PFLAG_SCSI_HOTPLUG;
-			spin_unlock_irqrestore(ap->lock, flags);
+			if (ata_dev_enabled(dev)) {
+				spin_lock_irqsave(ap->lock, flags);
+				ap->pflags |= ATA_PFLAG_SCSI_HOTPLUG;
+				spin_unlock_irqrestore(ap->lock, flags);
+
+				/* new device discovered, configure xfermode */
+				ehc->i.flags |= ATA_EHI_SETMODE;
+			}
 		}
 	}
 
@@ -1987,13 +2036,14 @@ static int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
 	if (rc)
 		goto dev_fail;
 
-	/* configure transfer mode if the port has been reset */
-	if (ehc->i.flags & ATA_EHI_DID_RESET) {
+	/* configure transfer mode if necessary */
+	if (ehc->i.flags & ATA_EHI_SETMODE) {
 		rc = ata_set_mode(ap, &dev);
 		if (rc) {
 			down_xfermask = 1;
 			goto dev_fail;
 		}
+		ehc->i.flags &= ~ATA_EHI_SETMODE;
 	}
 
 	/* suspend devices */

drivers/ata/libata-sff.c

@@ -38,6 +38,35 @@
 
 #include "libata.h"
 
+/**
+ *	ata_irq_on - Enable interrupts on a port.
+ *	@ap: Port on which interrupts are enabled.
+ *
+ *	Enable interrupts on a legacy IDE device using MMIO or PIO,
+ *	wait for idle, clear any pending interrupts.
+ *
+ *	LOCKING:
+ *	Inherited from caller.
+ */
+u8 ata_irq_on(struct ata_port *ap)
+{
+	struct ata_ioports *ioaddr = &ap->ioaddr;
+	u8 tmp;
+
+	ap->ctl &= ~ATA_NIEN;
+	ap->last_ctl = ap->ctl;
+
+	if (ap->flags & ATA_FLAG_MMIO)
+		writeb(ap->ctl, (void __iomem *) ioaddr->ctl_addr);
+	else
+		outb(ap->ctl, ioaddr->ctl_addr);
+	tmp = ata_wait_idle(ap);
+
+	ap->ops->irq_clear(ap);
+
+	return tmp;
+}
+
 /**
  *	ata_tf_load_pio - send taskfile registers to host controller
  *	@ap: Port to which output is sent
@@ -671,6 +700,14 @@ void ata_bmdma_freeze(struct ata_port *ap)
 		writeb(ap->ctl, (void __iomem *)ioaddr->ctl_addr);
 	else
 		outb(ap->ctl, ioaddr->ctl_addr);
+
+	/* Under certain circumstances, some controllers raise IRQ on
+	 * ATA_NIEN manipulation.  Also, many controllers fail to mask
+	 * previously pending IRQ on ATA_NIEN assertion.  Clear it.
+	 */
+	ata_chk_status(ap);
+
+	ap->ops->irq_clear(ap);
 }
 
 /**
@@ -714,7 +751,6 @@ void ata_bmdma_drive_eh(struct ata_port *ap, ata_prereset_fn_t prereset,
 			ata_reset_fn_t softreset, ata_reset_fn_t hardreset,
 			ata_postreset_fn_t postreset)
 {
-	struct ata_eh_context *ehc = &ap->eh_context;
 	struct ata_queued_cmd *qc;
 	unsigned long flags;
 	int thaw = 0;
@@ -732,9 +768,7 @@ void ata_bmdma_drive_eh(struct ata_port *ap, ata_prereset_fn_t prereset,
 		   qc->tf.protocol == ATA_PROT_ATAPI_DMA)) {
 		u8 host_stat;
 
-		host_stat = ata_bmdma_status(ap);
-
-		ata_ehi_push_desc(&ehc->i, "BMDMA stat 0x%x", host_stat);
+		host_stat = ap->ops->bmdma_status(ap);
 
 		/* BMDMA controllers indicate host bus error by
 		 * setting DMA_ERR bit and timing out.  As it wasn't
@@ -877,6 +911,7 @@ static struct ata_probe_ent *ata_pci_init_legacy_port(struct pci_dev *pdev,
 		return NULL;
 
 	probe_ent->n_ports = 2;
+	probe_ent->irq_flags = IRQF_SHARED;
 
 	if (port_mask & ATA_PORT_PRIMARY) {
 		probe_ent->irq = ATA_PRIMARY_IRQ;

drivers/ata/libata.h

@@ -39,26 +39,39 @@ struct ata_scsi_args {
 };
 
 /* libata-core.c */
+enum {
+	/* flags for ata_dev_read_id() */
+	ATA_READID_POSTRESET	= (1 << 0), /* reading ID after reset */
+};
+
 extern struct workqueue_struct *ata_aux_wq;
 extern int atapi_enabled;
 extern int atapi_dmadir;
 extern int libata_fua;
 extern struct ata_queued_cmd *ata_qc_new_init(struct ata_device *dev);
-extern int ata_rwcmd_protocol(struct ata_queued_cmd *qc);
+extern int ata_build_rw_tf(struct ata_taskfile *tf, struct ata_device *dev,
+			   u64 block, u32 n_block, unsigned int tf_flags,
+			   unsigned int tag);
+extern u64 ata_tf_read_block(struct ata_taskfile *tf, struct ata_device *dev);
 extern void ata_dev_disable(struct ata_device *dev);
 extern void ata_port_flush_task(struct ata_port *ap);
 extern unsigned ata_exec_internal(struct ata_device *dev,
 				  struct ata_taskfile *tf, const u8 *cdb,
 				  int dma_dir, void *buf, unsigned int buflen);
+extern unsigned ata_exec_internal_sg(struct ata_device *dev,
+				     struct ata_taskfile *tf, const u8 *cdb,
+				     int dma_dir, struct scatterlist *sg,
+				     unsigned int n_elem);
 extern unsigned int ata_do_simple_cmd(struct ata_device *dev, u8 cmd);
 extern int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class,
-			   int post_reset, u16 *id);
-extern int ata_dev_revalidate(struct ata_device *dev, int post_reset);
-extern int ata_dev_configure(struct ata_device *dev, int print_info);
+			   unsigned int flags, u16 *id);
+extern int ata_dev_revalidate(struct ata_device *dev, unsigned int flags);
+extern int ata_dev_configure(struct ata_device *dev);
 extern int sata_down_spd_limit(struct ata_port *ap);
 extern int sata_set_spd_needed(struct ata_port *ap);
 extern int ata_down_xfermask_limit(struct ata_device *dev, int force_pio0);
 extern int ata_set_mode(struct ata_port *ap, struct ata_device **r_failed_dev);
+extern void ata_sg_clean(struct ata_queued_cmd *qc);
 extern void ata_qc_free(struct ata_queued_cmd *qc);
 extern void ata_qc_issue(struct ata_queued_cmd *qc);
 extern void __ata_qc_complete(struct ata_queued_cmd *qc);
@@ -120,4 +133,7 @@ extern void ata_scsi_error(struct Scsi_Host *host);
 extern void ata_port_wait_eh(struct ata_port *ap);
 extern void ata_qc_schedule_eh(struct ata_queued_cmd *qc);
 
+/* libata-sff.c */
+extern u8 ata_irq_on(struct ata_port *ap);
+
 #endif /* __LIBATA_H__ */

drivers/ata/pata_ali.c

@@ -34,7 +34,7 @@
 #include <linux/dmi.h>
 
 #define DRV_NAME "pata_ali"
-#define DRV_VERSION "0.6.6"
+#define DRV_VERSION "0.7.2"
 
 /*
  *	Cable special cases
@@ -78,7 +78,7 @@ static int ali_c2_cable_detect(struct ata_port *ap)
 	   implement the detect logic */
 
 	if (ali_cable_override(pdev))
-		return ATA_CBL_PATA80;
+		return ATA_CBL_PATA40_SHORT;
 
 	/* Host view cable detect 0x4A bit 0 primary bit 1 secondary
 	   Bit set for 40 pin */
@@ -337,9 +337,6 @@ static struct scsi_host_template ali_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	/* Keep LBA28 counts so large I/O's don't turn LBA48 and PIO
-	   with older controllers. Not locked so will grow on C5 or later */
-	.max_sectors		= 255,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -348,6 +345,8 @@ static struct scsi_host_template ali_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 /*
@@ -497,6 +496,69 @@ static struct ata_port_operations ali_c5_port_ops = {
 	.host_stop	= ata_host_stop
 };
 
+
+/**
+ *	ali_init_chipset	-	chip setup function
+ *	@pdev: PCI device of ATA controller
+ *
+ *	Perform the setup on the device that must be done both at boot
+ *	and at resume time.
+ */
+ 
+static void ali_init_chipset(struct pci_dev *pdev)
+{
+	u8 rev, tmp;
+	struct pci_dev *north, *isa_bridge;
+
+	pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
+
+	/*
+	 * The chipset revision selects the driver operations and
+	 * mode data.
+	 */
+
+	if (rev >= 0x20 && rev < 0xC2) {
+		/* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */
+		pci_read_config_byte(pdev, 0x4B, &tmp);
+		/* Clear CD-ROM DMA write bit */
+		tmp &= 0x7F;
+		pci_write_config_byte(pdev, 0x4B, tmp);
+	} else if (rev >= 0xC2) {
+		/* Enable cable detection logic */
+		pci_read_config_byte(pdev, 0x4B, &tmp);
+		pci_write_config_byte(pdev, 0x4B, tmp | 0x08);
+	}
+	north = pci_get_bus_and_slot(0, PCI_DEVFN(0,0));
+	isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
+
+	if (north && north->vendor == PCI_VENDOR_ID_AL && isa_bridge) {
+		/* Configure the ALi bridge logic. For non ALi rely on BIOS.
+		   Set the south bridge enable bit */
+		pci_read_config_byte(isa_bridge, 0x79, &tmp);
+		if (rev == 0xC2)
+			pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04);
+		else if (rev > 0xC2 && rev < 0xC5)
+			pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02);
+	}
+	if (rev >= 0x20) {
+		/*
+		 * CD_ROM DMA on (0x53 bit 0). Enable this even if we want
+		 * to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control
+		 * via 0x54/55.
+		 */
+		pci_read_config_byte(pdev, 0x53, &tmp);
+		if (rev <= 0x20)
+			tmp &= ~0x02;
+		if (rev >= 0xc7)
+			tmp |= 0x03;
+		else
+			tmp |= 0x01;	/* CD_ROM enable for DMA */
+		pci_write_config_byte(pdev, 0x53, tmp);
+	}
+	pci_dev_put(isa_bridge);
+	pci_dev_put(north);
+	ata_pci_clear_simplex(pdev);
+}
 /**
  *	ali_init_one		-	discovery callback
  *	@pdev: PCI device ID
@@ -570,7 +632,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 
 	static struct ata_port_info *port_info[2];
 	u8 rev, tmp;
-	struct pci_dev *north, *isa_bridge;
+	struct pci_dev *isa_bridge;
 
 	pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
 
@@ -582,11 +644,6 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	if (rev < 0x20) {
 		port_info[0] = port_info[1] = &info_early;
 	} else if (rev < 0xC2) {
-		/* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */
-		pci_read_config_byte(pdev, 0x4B, &tmp);
-		/* Clear CD-ROM DMA write bit */
-		tmp &= 0x7F;
-		pci_write_config_byte(pdev, 0x4B, tmp);
         	port_info[0] = port_info[1] = &info_20;
 	} else if (rev == 0xC2) {
         	port_info[0] = port_info[1] = &info_c2;
@@ -597,54 +654,25 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	} else
         	port_info[0] = port_info[1] = &info_c5;
 
-	if (rev >= 0xC2) {
-		/* Enable cable detection logic */
-		pci_read_config_byte(pdev, 0x4B, &tmp);
-		pci_write_config_byte(pdev, 0x4B, tmp | 0x08);
-	}
-
-	north = pci_get_slot(pdev->bus, PCI_DEVFN(0,0));
+	ali_init_chipset(pdev);
+	
 	isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
-
-	if (north && north->vendor == PCI_VENDOR_ID_AL) {
-		/* Configure the ALi bridge logic. For non ALi rely on BIOS.
-		   Set the south bridge enable bit */
-		pci_read_config_byte(isa_bridge, 0x79, &tmp);
-		if (rev == 0xC2)
-			pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04);
-		else if (rev > 0xC2)
-			pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02);
-	}
-
-	if (rev >= 0x20) {
-		if (rev < 0xC2) {
-			/* Are we paired with a UDMA capable chip */
-			pci_read_config_byte(isa_bridge, 0x5E, &tmp);
-			if ((tmp & 0x1E) == 0x12)
-		        	port_info[0] = port_info[1] = &info_20_udma;
-		}
-		/*
-		 * CD_ROM DMA on (0x53 bit 0). Enable this even if we want
-		 * to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control
-		 * via 0x54/55.
-		 */
-		pci_read_config_byte(pdev, 0x53, &tmp);
-		if (rev <= 0x20)
-			tmp &= ~0x02;
-		if (rev >= 0xc7)
-			tmp |= 0x03;
-		else
-			tmp |= 0x01;	/* CD_ROM enable for DMA */
-		pci_write_config_byte(pdev, 0x53, tmp);
+	if (isa_bridge && rev >= 0x20 && rev < 0xC2) {
+		/* Are we paired with a UDMA capable chip */
+		pci_read_config_byte(isa_bridge, 0x5E, &tmp);
+		if ((tmp & 0x1E) == 0x12)
+	        	port_info[0] = port_info[1] = &info_20_udma;
+		pci_dev_put(isa_bridge);
 	}
-
-	pci_dev_put(isa_bridge);
-	pci_dev_put(north);
-
-	ata_pci_clear_simplex(pdev);
 	return ata_pci_init_one(pdev, port_info, 2);
 }
 
+static int ali_reinit_one(struct pci_dev *pdev)
+{
+	ali_init_chipset(pdev);
+	return ata_pci_device_resume(pdev);
+}
+
 static const struct pci_device_id ali[] = {
 	{ PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5228), },
 	{ PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5229), },
@@ -656,7 +684,9 @@ static struct pci_driver ali_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= ali,
 	.probe 		= ali_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= ali_reinit_one,
 };
 
 static int __init ali_init(void)

drivers/ata/pata_amd.c

@@ -25,7 +25,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "pata_amd"
-#define DRV_VERSION "0.2.4"
+#define DRV_VERSION "0.2.7"
 
 /**
  *	timing_setup		-	shared timing computation and load
@@ -326,7 +326,6 @@ static struct scsi_host_template amd_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -335,6 +334,8 @@ static struct scsi_host_template amd_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations amd33_port_ops = {
@@ -662,6 +663,23 @@ static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	return ata_pci_init_one(pdev, port_info, 2);
 }
 
+static int amd_reinit_one(struct pci_dev *pdev)
+{
+	if (pdev->vendor == PCI_VENDOR_ID_AMD) {
+		u8 fifo;
+		pci_read_config_byte(pdev, 0x41, &fifo);
+		if (pdev->device == PCI_DEVICE_ID_AMD_VIPER_7411)
+			/* FIFO is broken */
+			pci_write_config_byte(pdev, 0x41, fifo & 0x0F);
+		else
+			pci_write_config_byte(pdev, 0x41, fifo | 0xF0);
+		if (pdev->device == PCI_DEVICE_ID_AMD_VIPER_7409 ||
+		    pdev->device == PCI_DEVICE_ID_AMD_COBRA_7401)
+		    	ata_pci_clear_simplex(pdev);
+	}
+	return ata_pci_device_resume(pdev);
+}
+
 static const struct pci_device_id amd[] = {
 	{ PCI_VDEVICE(AMD,	PCI_DEVICE_ID_AMD_COBRA_7401),		0 },
 	{ PCI_VDEVICE(AMD,	PCI_DEVICE_ID_AMD_VIPER_7409),		1 },
@@ -689,7 +707,9 @@ static struct pci_driver amd_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= amd,
 	.probe 		= amd_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= amd_reinit_one,
 };
 
 static int __init amd_init(void)

drivers/ata/pata_artop.c

@@ -307,7 +307,6 @@ static struct scsi_host_template artop_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,

drivers/ata/pata_atiixp.c

@@ -22,7 +22,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "pata_atiixp"
-#define DRV_VERSION "0.4.3"
+#define DRV_VERSION "0.4.4"
 
 enum {
 	ATIIXP_IDE_PIO_TIMING	= 0x40,
@@ -209,7 +209,6 @@ static struct scsi_host_template atiixp_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -218,6 +217,8 @@ static struct scsi_host_template atiixp_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations atiixp_port_ops = {
@@ -281,7 +282,9 @@ static struct pci_driver atiixp_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= atiixp,
 	.probe 		= atiixp_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.resume		= ata_pci_device_resume,
+	.suspend	= ata_pci_device_suspend,
 };
 
 static int __init atiixp_init(void)

drivers/ata/pata_cmd64x.c

@@ -31,7 +31,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "pata_cmd64x"
-#define DRV_VERSION "0.2.1"
+#define DRV_VERSION "0.2.2"
 
 /*
  * CMD64x specific registers definition.
@@ -268,7 +268,6 @@ static struct scsi_host_template cmd64x_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -277,6 +276,8 @@ static struct scsi_host_template cmd64x_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations cmd64x_port_ops = {
@@ -469,6 +470,20 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	return ata_pci_init_one(pdev, port_info, 2);
 }
 
+static int cmd64x_reinit_one(struct pci_dev *pdev)
+{
+	u8 mrdmode;
+	pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 64);
+	pci_read_config_byte(pdev, MRDMODE, &mrdmode);
+	mrdmode &= ~ 0x30;	/* IRQ set up */
+	mrdmode |= 0x02;	/* Memory read line enable */
+	pci_write_config_byte(pdev, MRDMODE, mrdmode);
+#ifdef CONFIG_PPC
+	pci_write_config_byte(pdev, UDIDETCR0, 0xF0);
+#endif
+	return ata_pci_device_resume(pdev);
+}
+
 static const struct pci_device_id cmd64x[] = {
 	{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_643), 0 },
 	{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_646), 1 },
@@ -482,7 +497,9 @@ static struct pci_driver cmd64x_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= cmd64x,
 	.probe 		= cmd64x_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= cmd64x_reinit_one,
 };
 
 static int __init cmd64x_init(void)

drivers/ata/pata_cs5520.c

@@ -41,7 +41,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"pata_cs5520"
-#define DRV_VERSION	"0.6.2"
+#define DRV_VERSION	"0.6.3"
 
 struct pio_clocks
 {
@@ -159,7 +159,6 @@ static struct scsi_host_template cs5520_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -168,6 +167,8 @@ static struct scsi_host_template cs5520_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations cs5520_port_ops = {
@@ -297,6 +298,22 @@ static void __devexit cs5520_remove_one(struct pci_dev *pdev)
 	dev_set_drvdata(dev, NULL);
 }
 
+/**
+ *	cs5520_reinit_one	-	device resume
+ *	@pdev: PCI device
+ *
+ *	Do any reconfiguration work needed by a resume from RAM. We need
+ *	to restore DMA mode support on BIOSen which disabled it
+ */
+ 
+static int cs5520_reinit_one(struct pci_dev *pdev)
+{
+	u8 pcicfg;
+	pci_read_config_byte(pdev, 0x60, &pcicfg);
+	if ((pcicfg & 0x40) == 0)
+		pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
+	return ata_pci_device_resume(pdev);
+}
 /* For now keep DMA off. We can set it for all but A rev CS5510 once the
    core ATA code can handle it */
 
@@ -311,7 +328,9 @@ static struct pci_driver cs5520_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= pata_cs5520,
 	.probe 		= cs5520_init_one,
-	.remove		= cs5520_remove_one
+	.remove		= cs5520_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= cs5520_reinit_one,
 };
 
 static int __init cs5520_init(void)

drivers/ata/pata_cs5530.c

@@ -35,7 +35,7 @@
 #include <linux/dmi.h>
 
 #define DRV_NAME	"pata_cs5530"
-#define DRV_VERSION	"0.6"
+#define DRV_VERSION	"0.7.1"
 
 /**
  *	cs5530_set_piomode		-	PIO setup
@@ -173,7 +173,6 @@ static struct scsi_host_template cs5530_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -182,6 +181,8 @@ static struct scsi_host_template cs5530_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations cs5530_port_ops = {
@@ -239,38 +240,18 @@ static int cs5530_is_palmax(void)
 	return 0;
 }
 
+
 /**
- *	cs5530_init_one		-	Initialise a CS5530
- *	@dev: PCI device
- *	@id: Entry in match table
+ *	cs5530_init_chip	-	Chipset init
  *
- *	Install a driver for the newly found CS5530 companion chip. Most of
- *	this is just housekeeping. We have to set the chip up correctly and
- *	turn off various bits of emulation magic.
+ *	Perform the chip initialisation work that is shared between both
+ *	setup and resume paths
  */
-
-static int cs5530_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+ 
+static int cs5530_init_chip(void)
 {
-	int compiler_warning_pointless_fix;
-	struct pci_dev *master_0 = NULL, *cs5530_0 = NULL;
-	static struct ata_port_info info = {
-		.sht = &cs5530_sht,
-		.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
-		.pio_mask = 0x1f,
-		.mwdma_mask = 0x07,
-		.udma_mask = 0x07,
-		.port_ops = &cs5530_port_ops
-	};
-	/* The docking connector doesn't do UDMA, and it seems not MWDMA */
-	static struct ata_port_info info_palmax_secondary = {
-		.sht = &cs5530_sht,
-		.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
-		.pio_mask = 0x1f,
-		.port_ops = &cs5530_port_ops
-	};
-	static struct ata_port_info *port_info[2] = { &info, &info };
+	struct pci_dev *master_0 = NULL, *cs5530_0 = NULL, *dev = NULL;
 
-	dev = NULL;
 	while ((dev = pci_get_device(PCI_VENDOR_ID_CYRIX, PCI_ANY_ID, dev)) != NULL) {
 		switch (dev->device) {
 			case PCI_DEVICE_ID_CYRIX_PCI_MASTER:
@@ -291,7 +272,7 @@ static int cs5530_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 	}
 
 	pci_set_master(cs5530_0);
-	compiler_warning_pointless_fix = pci_set_mwi(cs5530_0);
+	pci_set_mwi(cs5530_0);
 
 	/*
 	 * Set PCI CacheLineSize to 16-bytes:
@@ -339,13 +320,7 @@ static int cs5530_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 
 	pci_dev_put(master_0);
 	pci_dev_put(cs5530_0);
-
-	if (cs5530_is_palmax())
-		port_info[1] = &info_palmax_secondary;
-
-	/* Now kick off ATA set up */
-	return ata_pci_init_one(dev, port_info, 2);
-
+	return 0;
 fail_put:
 	if (master_0)
 		pci_dev_put(master_0);
@@ -354,6 +329,53 @@ static int cs5530_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 	return -ENODEV;
 }
 
+/**
+ *	cs5530_init_one		-	Initialise a CS5530
+ *	@dev: PCI device
+ *	@id: Entry in match table
+ *
+ *	Install a driver for the newly found CS5530 companion chip. Most of
+ *	this is just housekeeping. We have to set the chip up correctly and
+ *	turn off various bits of emulation magic.
+ */
+
+static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	static struct ata_port_info info = {
+		.sht = &cs5530_sht,
+		.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+		.pio_mask = 0x1f,
+		.mwdma_mask = 0x07,
+		.udma_mask = 0x07,
+		.port_ops = &cs5530_port_ops
+	};
+	/* The docking connector doesn't do UDMA, and it seems not MWDMA */
+	static struct ata_port_info info_palmax_secondary = {
+		.sht = &cs5530_sht,
+		.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+		.pio_mask = 0x1f,
+		.port_ops = &cs5530_port_ops
+	};
+	static struct ata_port_info *port_info[2] = { &info, &info };
+	
+	/* Chip initialisation */
+	if (cs5530_init_chip())
+		return -ENODEV;
+		
+	if (cs5530_is_palmax())
+		port_info[1] = &info_palmax_secondary;
+
+	/* Now kick off ATA set up */
+	return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static int cs5530_reinit_one(struct pci_dev *pdev)
+{
+	/* If we fail on resume we are doomed */
+	BUG_ON(cs5530_init_chip());
+	return ata_pci_device_resume(pdev);
+}
+	
 static const struct pci_device_id cs5530[] = {
 	{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), },
 
@@ -364,7 +386,9 @@ static struct pci_driver cs5530_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= cs5530,
 	.probe 		= cs5530_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= cs5530_reinit_one,
 };
 
 static int __init cs5530_init(void)

drivers/ata/pata_cs5535.c

@@ -39,7 +39,7 @@
 #include <asm/msr.h>
 
 #define DRV_NAME	"cs5535"
-#define DRV_VERSION	"0.2.10"
+#define DRV_VERSION	"0.2.11"
 
 /*
  *	The Geode (Aka Athlon GX now) uses an internal MSR based
@@ -177,7 +177,6 @@ static struct scsi_host_template cs5535_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -186,6 +185,8 @@ static struct scsi_host_template cs5535_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations cs5535_port_ops = {
@@ -268,7 +269,9 @@ static struct pci_driver cs5535_pci_driver = {
 	.name		= DRV_NAME,
 	.id_table	= cs5535,
 	.probe 		= cs5535_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= ata_pci_device_resume,
 };
 
 static int __init cs5535_init(void)

drivers/ata/pata_cypress.c

@@ -18,7 +18,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "pata_cypress"
-#define DRV_VERSION "0.1.2"
+#define DRV_VERSION "0.1.4"
 
 /* here are the offset definitions for the registers */
 
@@ -128,7 +128,6 @@ static struct scsi_host_template cy82c693_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -137,6 +136,8 @@ static struct scsi_host_template cy82c693_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations cy82c693_port_ops = {
@@ -204,7 +205,9 @@ static struct pci_driver cy82c693_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= cy82c693,
 	.probe 		= cy82c693_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= ata_pci_device_resume,
 };
 
 static int __init cy82c693_init(void)

drivers/ata/pata_efar.c

@@ -22,7 +22,7 @@
 #include <linux/ata.h>
 
 #define DRV_NAME	"pata_efar"
-#define DRV_VERSION	"0.4.2"
+#define DRV_VERSION	"0.4.3"
 
 /**
  *	efar_pre_reset	-	check for 40/80 pin
@@ -226,7 +226,6 @@ static struct scsi_host_template efar_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -235,6 +234,8 @@ static struct scsi_host_template efar_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static const struct ata_port_operations efar_ops = {
@@ -316,6 +317,8 @@ static struct pci_driver efar_pci_driver = {
 	.id_table		= efar_pci_tbl,
 	.probe			= efar_init_one,
 	.remove			= ata_pci_remove_one,
+	.suspend		= ata_pci_device_suspend,
+	.resume			= ata_pci_device_resume,
 };
 
 static int __init efar_init(void)

drivers/ata/pata_hpt366.c

@@ -27,7 +27,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"pata_hpt366"
-#define DRV_VERSION	"0.5"
+#define DRV_VERSION	"0.5.3"
 
 struct hpt_clock {
 	u8	xfer_speed;
@@ -222,9 +222,17 @@ static u32 hpt36x_find_mode(struct ata_port *ap, int speed)
 
 static int hpt36x_pre_reset(struct ata_port *ap)
 {
+	static const struct pci_bits hpt36x_enable_bits[] = {
+		{ 0x50, 1, 0x04, 0x04 },
+		{ 0x54, 1, 0x04, 0x04 }
+	};
+
 	u8 ata66;
 	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 
+	if (!pci_test_config_bits(pdev, &hpt36x_enable_bits[ap->port_no]))
+		return -ENOENT;
+		
 	pci_read_config_byte(pdev, 0x5A, &ata66);
 	if (ata66 & (1 << ap->port_no))
 		ap->cbl = ATA_CBL_PATA40;
@@ -322,7 +330,6 @@ static struct scsi_host_template hpt36x_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -331,6 +338,8 @@ static struct scsi_host_template hpt36x_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 /*
@@ -372,6 +381,27 @@ static struct ata_port_operations hpt366_port_ops = {
 	.host_stop	= ata_host_stop
 };
 
+/**
+ *	hpt36x_init_chipset	-	common chip setup
+ *	@dev: PCI device
+ *
+ *	Perform the chip setup work that must be done at both init and
+ *	resume time
+ */
+
+static void hpt36x_init_chipset(struct pci_dev *dev)
+{
+	u8 drive_fast;
+	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+	pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+	pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+
+	pci_read_config_byte(dev, 0x51, &drive_fast);
+	if (drive_fast & 0x80)
+		pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
+}
+
 /**
  *	hpt36x_init_one		-	Initialise an HPT366/368
  *	@dev: PCI device
@@ -407,7 +437,6 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 
 	u32 class_rev;
 	u32 reg1;
-	u8 drive_fast;
 
 	pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
 	class_rev &= 0xFF;
@@ -417,14 +446,7 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 	if (class_rev > 2)
 			return -ENODEV;
 
-	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
-	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
-	pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
-	pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
-
-	pci_read_config_byte(dev, 0x51, &drive_fast);
-	if (drive_fast & 0x80)
-		pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
+	hpt36x_init_chipset(dev);
 
 	pci_read_config_dword(dev, 0x40,  &reg1);
 
@@ -445,9 +467,15 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 	return ata_pci_init_one(dev, port_info, 2);
 }
 
+static int hpt36x_reinit_one(struct pci_dev *dev)
+{
+	hpt36x_init_chipset(dev);
+	return ata_pci_device_resume(dev);
+}
+
+
 static const struct pci_device_id hpt36x[] = {
 	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
-
 	{ },
 };
 
@@ -455,7 +483,9 @@ static struct pci_driver hpt36x_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= hpt36x,
 	.probe 		= hpt36x_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= hpt36x_reinit_one,
 };
 
 static int __init hpt36x_init(void)
@@ -463,13 +493,11 @@ static int __init hpt36x_init(void)
 	return pci_register_driver(&hpt36x_pci_driver);
 }
 
-
 static void __exit hpt36x_exit(void)
 {
 	pci_unregister_driver(&hpt36x_pci_driver);
 }
 
-
 MODULE_AUTHOR("Alan Cox");
 MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368");
 MODULE_LICENSE("GPL");

drivers/ata/pata_hpt37x.c

@@ -768,7 +768,6 @@ static struct scsi_host_template hpt37x_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,

drivers/ata/pata_hpt3x2n.c

@@ -334,7 +334,6 @@ static struct scsi_host_template hpt3x2n_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,

drivers/ata/pata_hpt3x3.c

@@ -23,7 +23,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"pata_hpt3x3"
-#define DRV_VERSION	"0.4.1"
+#define DRV_VERSION	"0.4.2"
 
 static int hpt3x3_probe_init(struct ata_port *ap)
 {
@@ -111,7 +111,6 @@ static struct scsi_host_template hpt3x3_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -120,6 +119,8 @@ static struct scsi_host_template hpt3x3_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations hpt3x3_port_ops = {
@@ -157,6 +158,27 @@ static struct ata_port_operations hpt3x3_port_ops = {
 	.host_stop	= ata_host_stop
 };
 
+/**
+ *	hpt3x3_init_chipset	-	chip setup
+ *	@dev: PCI device
+ *
+ *	Perform the setup required at boot and on resume.
+ */
+ 
+static void hpt3x3_init_chipset(struct pci_dev *dev)
+{
+	u16 cmd;
+	/* Initialize the board */
+	pci_write_config_word(dev, 0x80, 0x00);
+	/* Check if it is a 343 or a 363. 363 has COMMAND_MEMORY set */
+	pci_read_config_word(dev, PCI_COMMAND, &cmd);
+	if (cmd & PCI_COMMAND_MEMORY)
+		pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xF0);
+	else
+		pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
+}
+
+
 /**
  *	hpt3x3_init_one		-	Initialise an HPT343/363
  *	@dev: PCI device
@@ -178,21 +200,18 @@ static int hpt3x3_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 		.port_ops = &hpt3x3_port_ops
 	};
 	static struct ata_port_info *port_info[2] = { &info, &info };
-	u16 cmd;
-
-	/* Initialize the board */
-	pci_write_config_word(dev, 0x80, 0x00);
-	/* Check if it is a 343 or a 363. 363 has COMMAND_MEMORY set */
-	pci_read_config_word(dev, PCI_COMMAND, &cmd);
-	if (cmd & PCI_COMMAND_MEMORY)
-		pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xF0);
-	else
-		pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
 
+	hpt3x3_init_chipset(dev);
 	/* Now kick off ATA set up */
 	return ata_pci_init_one(dev, port_info, 2);
 }
 
+static int hpt3x3_reinit_one(struct pci_dev *dev)
+{
+	hpt3x3_init_chipset(dev);
+	return ata_pci_device_resume(dev);
+}
+
 static const struct pci_device_id hpt3x3[] = {
 	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT343), },
 
@@ -203,7 +222,9 @@ static struct pci_driver hpt3x3_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= hpt3x3,
 	.probe 		= hpt3x3_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= hpt3x3_reinit_one,
 };
 
 static int __init hpt3x3_init(void)

drivers/ata/pata_isapnp.c

@@ -27,7 +27,6 @@ static struct scsi_host_template isapnp_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,

drivers/ata/pata_it821x.c

@@ -80,7 +80,7 @@
 
 
 #define DRV_NAME "pata_it821x"
-#define DRV_VERSION "0.3.2"
+#define DRV_VERSION "0.3.3"
 
 struct it821x_dev
 {
@@ -666,9 +666,6 @@ static struct scsi_host_template it821x_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	/* 255 sectors to begin with. This is locked in smart mode but not
-	   in pass through */
-	.max_sectors		= 255,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -677,6 +674,8 @@ static struct scsi_host_template it821x_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations it821x_smart_port_ops = {
@@ -809,6 +808,14 @@ static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	return ata_pci_init_one(pdev, port_info, 2);
 }
 
+static int it821x_reinit_one(struct pci_dev *pdev)
+{
+	/* Resume - turn raid back off if need be */
+	if (it8212_noraid)
+		it821x_disable_raid(pdev);
+	return ata_pci_device_resume(pdev);
+}
+
 static const struct pci_device_id it821x[] = {
 	{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), },
 	{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), },
@@ -820,7 +827,9 @@ static struct pci_driver it821x_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= it821x,
 	.probe 		= it821x_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= it821x_reinit_one,
 };
 
 static int __init it821x_init(void)

drivers/ata/pata_ixp4xx_cf.c

+/*
+ * ixp4xx PATA/Compact Flash driver
+ * Copyright (c) 2006 Tower Technologies
+ * Author: Alessandro Zummo <a.zummo@towertech.it>
+ *
+ * An ATA driver to handle a Compact Flash connected
+ * to the ixp4xx expansion bus in TrueIDE mode. The CF
+ * must have it chip selects connected to two CS lines
+ * on the ixp4xx. The interrupt line is optional, if not
+ * specified the driver will run in polling mode.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/libata.h>
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <scsi/scsi_host.h>
+
+#define DRV_NAME	"pata_ixp4xx_cf"
+#define DRV_VERSION	"0.1.1"
+
+static void ixp4xx_set_mode(struct ata_port *ap)
+{
+	int i;
+
+	for (i = 0; i < ATA_MAX_DEVICES; i++) {
+		struct ata_device *dev = &ap->device[i];
+		if (ata_dev_enabled(dev)) {
+			dev->pio_mode = XFER_PIO_0;
+			dev->xfer_mode = XFER_PIO_0;
+			dev->xfer_shift = ATA_SHIFT_PIO;
+			dev->flags |= ATA_DFLAG_PIO;
+		}
+	}
+}
+
+static void ixp4xx_phy_reset(struct ata_port *ap)
+{
+	ap->cbl = ATA_CBL_PATA40;
+	ata_port_probe(ap);
+	ata_bus_reset(ap);
+}
+
+static void ixp4xx_mmio_data_xfer(struct ata_device *adev, unsigned char *buf,
+				unsigned int buflen, int write_data)
+{
+	unsigned int i;
+	unsigned int words = buflen >> 1;
+	u16 *buf16 = (u16 *) buf;
+	struct ata_port *ap = adev->ap;
+	void __iomem *mmio = (void __iomem *)ap->ioaddr.data_addr;
+	struct ixp4xx_pata_data *data = ap->host->dev->platform_data;
+
+	/* set the expansion bus in 16bit mode and restore
+	 * 8 bit mode after the transaction.
+	 */
+	*data->cs0_cfg &= ~(0x01);
+	udelay(100);
+
+	/* Transfer multiple of 2 bytes */
+	if (write_data) {
+		for (i = 0; i < words; i++)
+			writew(buf16[i], mmio);
+	} else {
+		for (i = 0; i < words; i++)
+			buf16[i] = readw(mmio);
+	}
+
+	/* Transfer trailing 1 byte, if any. */
+	if (unlikely(buflen & 0x01)) {
+		u16 align_buf[1] = { 0 };
+		unsigned char *trailing_buf = buf + buflen - 1;
+
+		if (write_data) {
+			memcpy(align_buf, trailing_buf, 1);
+			writew(align_buf[0], mmio);
+		} else {
+			align_buf[0] = readw(mmio);
+			memcpy(trailing_buf, align_buf, 1);
+		}
+	}
+
+	udelay(100);
+	*data->cs0_cfg |= 0x01;
+}
+
+static void ixp4xx_irq_clear(struct ata_port *ap)
+{
+}
+
+static void ixp4xx_host_stop (struct ata_host *host)
+{
+	struct ixp4xx_pata_data *data = host->dev->platform_data;
+
+	iounmap(data->cs0);
+	iounmap(data->cs1);
+}
+
+static struct scsi_host_template ixp4xx_sht = {
+	.module			= THIS_MODULE,
+	.name			= DRV_NAME,
+	.ioctl			= ata_scsi_ioctl,
+	.queuecommand		= ata_scsi_queuecmd,
+	.can_queue		= ATA_DEF_QUEUE,
+	.this_id		= ATA_SHT_THIS_ID,
+	.sg_tablesize		= LIBATA_MAX_PRD,
+	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
+	.emulated		= ATA_SHT_EMULATED,
+	.use_clustering		= ATA_SHT_USE_CLUSTERING,
+	.proc_name		= DRV_NAME,
+	.dma_boundary		= ATA_DMA_BOUNDARY,
+	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
+	.bios_param		= ata_std_bios_param,
+};
+
+static struct ata_port_operations ixp4xx_port_ops = {
+	.set_mode	= ixp4xx_set_mode,
+	.mode_filter	= ata_pci_default_filter,
+
+	.port_disable	= ata_port_disable,
+	.tf_load	= ata_tf_load,
+	.tf_read	= ata_tf_read,
+	.check_status 	= ata_check_status,
+	.exec_command	= ata_exec_command,
+	.dev_select 	= ata_std_dev_select,
+
+	.qc_prep 	= ata_qc_prep,
+	.qc_issue	= ata_qc_issue_prot,
+	.eng_timeout	= ata_eng_timeout,
+	.data_xfer	= ixp4xx_mmio_data_xfer,
+
+	.irq_handler	= ata_interrupt,
+	.irq_clear	= ixp4xx_irq_clear,
+
+	.port_start	= ata_port_start,
+	.port_stop	= ata_port_stop,
+	.host_stop	= ixp4xx_host_stop,
+
+	.phy_reset	= ixp4xx_phy_reset,
+};
+
+static void ixp4xx_setup_port(struct ata_ioports *ioaddr,
+				struct ixp4xx_pata_data *data)
+{
+	ioaddr->cmd_addr	= (unsigned long) data->cs0;
+	ioaddr->altstatus_addr	= (unsigned long) data->cs1 + 0x06;
+	ioaddr->ctl_addr	= (unsigned long) data->cs1 + 0x06;
+
+	ata_std_ports(ioaddr);
+
+#ifndef __ARMEB__
+
+	/* adjust the addresses to handle the address swizzling of the
+	 * ixp4xx in little endian mode.
+	 */
+
+	ioaddr->data_addr	^= 0x02;
+	ioaddr->cmd_addr	^= 0x03;
+	ioaddr->altstatus_addr	^= 0x03;
+	ioaddr->ctl_addr	^= 0x03;
+	ioaddr->error_addr	^= 0x03;
+	ioaddr->feature_addr	^= 0x03;
+	ioaddr->nsect_addr	^= 0x03;
+	ioaddr->lbal_addr 	^= 0x03;
+	ioaddr->lbam_addr	^= 0x03;
+	ioaddr->lbah_addr	^= 0x03;
+	ioaddr->device_addr	^= 0x03;
+	ioaddr->status_addr	^= 0x03;
+	ioaddr->command_addr	^= 0x03;
+#endif
+}
+
+static __devinit int ixp4xx_pata_probe(struct platform_device *pdev)
+{
+	int ret;
+	unsigned int irq;
+	struct resource *cs0, *cs1;
+	struct ata_probe_ent ae;
+
+	struct ixp4xx_pata_data *data = pdev->dev.platform_data;
+
+	cs0 = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	cs1 = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+
+	if (!cs0 || !cs1)
+		return -EINVAL;
+
+	pdev->dev.coherent_dma_mask = DMA_32BIT_MASK;
+
+	data->cs0 = ioremap(cs0->start, 0x1000);
+	data->cs1 = ioremap(cs1->start, 0x1000);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq)
+		set_irq_type(irq, IRQT_HIGH);
+
+	/* Setup expansion bus chip selects */
+	*data->cs0_cfg = data->cs0_bits;
+	*data->cs1_cfg = data->cs1_bits;
+
+	memset(&ae, 0, sizeof(struct ata_probe_ent));
+	INIT_LIST_HEAD(&ae.node);
+
+	ae.dev		= &pdev->dev;
+	ae.port_ops	= &ixp4xx_port_ops;
+	ae.sht		= &ixp4xx_sht;
+	ae.n_ports	= 1;
+	ae.pio_mask	= 0x1f; /* PIO4 */
+	ae.irq		= irq;
+	ae.irq_flags	= 0;
+	ae.port_flags	= ATA_FLAG_MMIO | ATA_FLAG_NO_LEGACY
+			| ATA_FLAG_NO_ATAPI | ATA_FLAG_SRST;
+
+	/* run in polling mode if no irq has been assigned */
+	if (!irq)
+		ae.port_flags |= ATA_FLAG_PIO_POLLING;
+
+	ixp4xx_setup_port(&ae.port[0], data);
+
+	dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
+
+	ret = ata_device_add(&ae);
+	if (ret == 0)
+		return -ENODEV;
+
+	return 0;
+}
+
+static __devexit int ixp4xx_pata_remove(struct platform_device *dev)
+{
+	struct ata_host *host = platform_get_drvdata(dev);
+
+	ata_host_remove(host);
+	platform_set_drvdata(dev, NULL);
+
+	return 0;
+}
+
+static struct platform_driver ixp4xx_pata_platform_driver = {
+	.driver	 = {
+		.name   = DRV_NAME,
+		.owner  = THIS_MODULE,
+	},
+	.probe		= ixp4xx_pata_probe,
+	.remove		= __devexit_p(ixp4xx_pata_remove),
+};
+
+static int __init ixp4xx_pata_init(void)
+{
+	return platform_driver_register(&ixp4xx_pata_platform_driver);
+}
+
+static void __exit ixp4xx_pata_exit(void)
+{
+	platform_driver_unregister(&ixp4xx_pata_platform_driver);
+}
+
+MODULE_AUTHOR("Alessandro Zummo <a.zummo@towertech.it>");
+MODULE_DESCRIPTION("low-level driver for ixp4xx Compact Flash PATA");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+module_init(ixp4xx_pata_init);
+module_exit(ixp4xx_pata_exit);

drivers/ata/pata_jmicron.c

@@ -19,7 +19,7 @@
 #include <linux/ata.h>
 
 #define DRV_NAME	"pata_jmicron"
-#define DRV_VERSION	"0.1.2"
+#define DRV_VERSION	"0.1.4"
 
 typedef enum {
 	PORT_PATA0 = 0,
@@ -128,8 +128,6 @@ static struct scsi_host_template jmicron_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	/* Special handling needed if you have sector or LBA48 limits */
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -213,12 +211,11 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i
 
 		/* FIXME: We may want a way to override this in future */
 		pci_write_config_byte(pdev, 0x41, 0xa1);
-	}
-
-	/* PATA controller is fn 1, AHCI is fn 0 */
-	if (PCI_FUNC(pdev->devfn) != 1)
-		return -ENODEV;
 
+		/* PATA controller is fn 1, AHCI is fn 0 */
+		if (PCI_FUNC(pdev->devfn) != 1)
+			return -ENODEV;
+	}
 	if ( id->driver_data == 365 || id->driver_data == 366) {
 		/* The 365/66 have two PATA channels, redirect the second */
 		pci_read_config_dword(pdev, 0x80, &reg);
@@ -229,6 +226,27 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i
 	return ata_pci_init_one(pdev, port_info, 2);
 }
 
+static int jmicron_reinit_one(struct pci_dev *pdev)
+{
+	u32 reg;
+	
+	switch(pdev->device) {
+		case PCI_DEVICE_ID_JMICRON_JMB368:
+			break;
+		case PCI_DEVICE_ID_JMICRON_JMB365:
+		case PCI_DEVICE_ID_JMICRON_JMB366:
+			/* Restore mapping or disks swap and boy does it get ugly */
+			pci_read_config_dword(pdev, 0x80, &reg);
+			reg |= (1 << 24);	/* IDE1 to PATA IDE secondary */
+			pci_write_config_dword(pdev, 0x80, reg);
+			/* Fall through */
+		default:
+			/* Make sure AHCI is turned back on */
+			pci_write_config_byte(pdev, 0x41, 0xa1);
+	}
+	return ata_pci_device_resume(pdev);
+}
+
 static const struct pci_device_id jmicron_pci_tbl[] = {
 	{ PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB361), 361},
 	{ PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB363), 363},
@@ -244,6 +262,8 @@ static struct pci_driver jmicron_pci_driver = {
 	.id_table		= jmicron_pci_tbl,
 	.probe			= jmicron_init_one,
 	.remove			= ata_pci_remove_one,
+	.suspend		= ata_pci_device_suspend,
+	.resume			= jmicron_reinit_one,
 };
 
 static int __init jmicron_init(void)

drivers/ata/pata_legacy.c

@@ -128,7 +128,6 @@ static struct scsi_host_template legacy_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,

drivers/ata/pata_marvell.c

+/*
+ *	Marvell PATA driver.
+ *
+ *	For the moment we drive the PATA port in legacy mode. That
+ *	isn't making full use of the device functionality but it is
+ *	easy to get working.
+ *
+ *	(c) 2006 Red Hat  <alan@redhat.com>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME	"pata_marvell"
+#define DRV_VERSION	"0.1.1"
+
+/**
+ *	marvell_pre_reset	-	check for 40/80 pin
+ *	@ap: Port
+ *
+ *	Perform the PATA port setup we need.
+ */
+
+static int marvell_pre_reset(struct ata_port *ap)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u32 devices;
+	void __iomem *barp;
+	int i;
+
+	/* Check if our port is enabled */
+
+	barp = pci_iomap(pdev, 5, 0x10);
+	if (barp == NULL)
+		return -ENOMEM;
+	printk("BAR5:");
+	for(i = 0; i <= 0x0F; i++)
+		printk("%02X:%02X ", i, readb(barp + i));
+	printk("\n");
+	
+	devices = readl(barp + 0x0C);
+	pci_iounmap(pdev, barp);
+	
+	if ((pdev->device == 0x6145) && (ap->port_no == 0) &&
+	    (!(devices & 0x10)))	/* PATA enable ? */
+		return -ENOENT;
+
+	/* Cable type */
+	switch(ap->port_no)
+	{
+	case 0:
+		if (inb(ap->ioaddr.bmdma_addr + 1) & 1)
+			ap->cbl = ATA_CBL_PATA40;
+		else
+			ap->cbl = ATA_CBL_PATA80;
+		break;
+
+	case 1: /* Legacy SATA port */
+		ap->cbl = ATA_CBL_SATA;
+		break;
+	}
+	return ata_std_prereset(ap);
+}
+
+/**
+ *	marvell_error_handler - Setup and error handler
+ *	@ap: Port to handle
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void marvell_error_handler(struct ata_port *ap)
+{
+	return ata_bmdma_drive_eh(ap, marvell_pre_reset, ata_std_softreset,
+				  NULL, ata_std_postreset);
+}
+
+/* No PIO or DMA methods needed for this device */
+
+static struct scsi_host_template marvell_sht = {
+	.module			= THIS_MODULE,
+	.name			= DRV_NAME,
+	.ioctl			= ata_scsi_ioctl,
+	.queuecommand		= ata_scsi_queuecmd,
+	.can_queue		= ATA_DEF_QUEUE,
+	.this_id		= ATA_SHT_THIS_ID,
+	.sg_tablesize		= LIBATA_MAX_PRD,
+	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
+	.emulated		= ATA_SHT_EMULATED,
+	.use_clustering		= ATA_SHT_USE_CLUSTERING,
+	.proc_name		= DRV_NAME,
+	.dma_boundary		= ATA_DMA_BOUNDARY,
+	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
+	/* Use standard CHS mapping rules */
+	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
+};
+
+static const struct ata_port_operations marvell_ops = {
+	.port_disable		= ata_port_disable,
+
+	/* Task file is PCI ATA format, use helpers */
+	.tf_load		= ata_tf_load,
+	.tf_read		= ata_tf_read,
+	.check_status		= ata_check_status,
+	.exec_command		= ata_exec_command,
+	.dev_select		= ata_std_dev_select,
+
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= marvell_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
+
+	/* BMDMA handling is PCI ATA format, use helpers */
+	.bmdma_setup		= ata_bmdma_setup,
+	.bmdma_start		= ata_bmdma_start,
+	.bmdma_stop		= ata_bmdma_stop,
+	.bmdma_status		= ata_bmdma_status,
+	.qc_prep		= ata_qc_prep,
+	.qc_issue		= ata_qc_issue_prot,
+	.data_xfer		= ata_pio_data_xfer,
+
+	/* Timeout handling */
+	.irq_handler		= ata_interrupt,
+	.irq_clear		= ata_bmdma_irq_clear,
+
+	/* Generic PATA PCI ATA helpers */
+	.port_start		= ata_port_start,
+	.port_stop		= ata_port_stop,
+	.host_stop		= ata_host_stop,
+};
+
+
+/**
+ *	marvell_init_one - Register Marvell ATA PCI device with kernel services
+ *	@pdev: PCI device to register
+ *	@ent: Entry in marvell_pci_tbl matching with @pdev
+ *
+ *	Called from kernel PCI layer.
+ *
+ *	LOCKING:
+ *	Inherited from PCI layer (may sleep).
+ *
+ *	RETURNS:
+ *	Zero on success, or -ERRNO value.
+ */
+
+static int marvell_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	static struct ata_port_info info = {
+		.sht		= &marvell_sht,
+		.flags		= ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+
+		.pio_mask	= 0x1f,
+		.mwdma_mask	= 0x07,
+		.udma_mask 	= 0x3f,
+
+		.port_ops	= &marvell_ops,
+	};
+	static struct ata_port_info info_sata = {
+		.sht		= &marvell_sht,
+		/* Slave possible as its magically mapped not real */
+		.flags		= ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+
+		.pio_mask	= 0x1f,
+		.mwdma_mask	= 0x07,
+		.udma_mask 	= 0x7f,
+
+		.port_ops	= &marvell_ops,
+	};
+	struct ata_port_info *port_info[2] = { &info, &info_sata };
+	int n_port = 2;
+
+	if (pdev->device == 0x6101)
+		n_port = 1;
+
+	return ata_pci_init_one(pdev, port_info, n_port);
+}
+
+static const struct pci_device_id marvell_pci_tbl[] = {
+	{ PCI_DEVICE(0x11AB, 0x6101), },
+	{ PCI_DEVICE(0x11AB, 0x6145), },
+	{ }	/* terminate list */
+};
+
+static struct pci_driver marvell_pci_driver = {
+	.name			= DRV_NAME,
+	.id_table		= marvell_pci_tbl,
+	.probe			= marvell_init_one,
+	.remove			= ata_pci_remove_one,
+	.suspend		= ata_pci_device_suspend,
+	.resume			= ata_pci_device_resume,
+};
+
+static int __init marvell_init(void)
+{
+	return pci_register_driver(&marvell_pci_driver);
+}
+
+static void __exit marvell_exit(void)
+{
+	pci_unregister_driver(&marvell_pci_driver);
+}
+
+module_init(marvell_init);
+module_exit(marvell_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for Marvell ATA in legacy mode");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, marvell_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+

drivers/ata/pata_mpiix.c

@@ -35,7 +35,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "pata_mpiix"
-#define DRV_VERSION "0.7.2"
+#define DRV_VERSION "0.7.3"
 
 enum {
 	IDETIM = 0x6C,		/* IDE control register */
@@ -159,7 +159,6 @@ static struct scsi_host_template mpiix_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -168,6 +167,8 @@ static struct scsi_host_template mpiix_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations mpiix_port_ops = {
@@ -285,7 +286,9 @@ static struct pci_driver mpiix_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= mpiix,
 	.probe 		= mpiix_init_one,
-	.remove		= mpiix_remove_one
+	.remove		= mpiix_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= ata_pci_device_resume,
 };
 
 static int __init mpiix_init(void)

drivers/ata/pata_netcell.c

@@ -16,7 +16,7 @@
 #include <linux/ata.h>
 
 #define DRV_NAME	"pata_netcell"
-#define DRV_VERSION	"0.1.5"
+#define DRV_VERSION	"0.1.6"
 
 /**
  *	netcell_probe_init	-	check for 40/80 pin
@@ -54,8 +54,6 @@ static struct scsi_host_template netcell_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	/* Special handling needed if you have sector or LBA48 limits */
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -65,6 +63,8 @@ static struct scsi_host_template netcell_sht = {
 	.slave_destroy		= ata_scsi_slave_destroy,
 	/* Use standard CHS mapping rules */
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static const struct ata_port_operations netcell_ops = {
@@ -153,6 +153,8 @@ static struct pci_driver netcell_pci_driver = {
 	.id_table		= netcell_pci_tbl,
 	.probe			= netcell_init_one,
 	.remove			= ata_pci_remove_one,
+	.suspend		= ata_pci_device_suspend,
+	.resume			= ata_pci_device_resume,
 };
 
 static int __init netcell_init(void)

drivers/ata/pata_ns87410.c

@@ -28,7 +28,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "pata_ns87410"
-#define DRV_VERSION "0.4.2"
+#define DRV_VERSION "0.4.3"
 
 /**
  *	ns87410_pre_reset		-	probe begin
@@ -149,7 +149,6 @@ static struct scsi_host_template ns87410_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -158,6 +157,8 @@ static struct scsi_host_template ns87410_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations ns87410_port_ops = {
@@ -210,7 +211,9 @@ static struct pci_driver ns87410_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= ns87410,
 	.probe 		= ns87410_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= ata_pci_device_resume,
 };
 
 static int __init ns87410_init(void)

drivers/ata/pata_oldpiix.c

@@ -224,7 +224,6 @@ static struct scsi_host_template oldpiix_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -233,6 +232,8 @@ static struct scsi_host_template oldpiix_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static const struct ata_port_operations oldpiix_pata_ops = {
@@ -314,6 +315,8 @@ static struct pci_driver oldpiix_pci_driver = {
 	.id_table		= oldpiix_pci_tbl,
 	.probe			= oldpiix_init_one,
 	.remove			= ata_pci_remove_one,
+	.suspend		= ata_pci_device_suspend,
+	.resume			= ata_pci_device_resume,
 };
 
 static int __init oldpiix_init(void)

drivers/ata/pata_opti.c

@@ -34,7 +34,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "pata_opti"
-#define DRV_VERSION "0.2.5"
+#define DRV_VERSION "0.2.7"
 
 enum {
 	READ_REG	= 0,	/* index of Read cycle timing register */
@@ -109,30 +109,6 @@ static void opti_write_reg(struct ata_port *ap, u8 val, int reg)
 	outb(0x83, regio + 2);
 }
 
-#if 0
-/**
- *	opti_read_reg		-	control register read
- *	@ap: ATA port
- *	@reg: control register number
- *
- *	The Opti uses magic 'trapdoor' register accesses to do configuration
- *	rather than using PCI space as other controllers do. The double inw
- *	on the error register activates configuration mode. We can then read
- *	the control register
- */
-
-static u8 opti_read_reg(struct ata_port *ap, int reg)
-{
-	unsigned long regio = ap->ioaddr.cmd_addr;
-	u8 ret;
-	inw(regio + 1);
-	inw(regio + 1);
-	outb(3, regio + 2);
-	ret = inb(regio + reg);
-	outb(0x83, regio + 2);
-}
-#endif
-
 /**
  *	opti_set_piomode	-	set initial PIO mode data
  *	@ap: ATA interface
@@ -195,7 +171,6 @@ static struct scsi_host_template opti_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -204,12 +179,13 @@ static struct scsi_host_template opti_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations opti_port_ops = {
 	.port_disable	= ata_port_disable,
 	.set_piomode	= opti_set_piomode,
-/*	.set_dmamode	= opti_set_dmamode, */
 	.tf_load	= ata_tf_load,
 	.tf_read	= ata_tf_read,
 	.check_status 	= ata_check_status,
@@ -267,7 +243,9 @@ static struct pci_driver opti_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= opti,
 	.probe 		= opti_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= ata_pci_device_resume,
 };
 
 static int __init opti_init(void)

drivers/ata/pata_optidma.c

@@ -33,7 +33,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "pata_optidma"
-#define DRV_VERSION "0.2.2"
+#define DRV_VERSION "0.2.3"
 
 enum {
 	READ_REG	= 0,	/* index of Read cycle timing register */
@@ -352,7 +352,6 @@ static struct scsi_host_template optidma_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -361,6 +360,8 @@ static struct scsi_host_template optidma_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations optidma_port_ops = {
@@ -522,7 +523,9 @@ static struct pci_driver optidma_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= optidma,
 	.probe 		= optidma_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= ata_pci_device_resume,
 };
 
 static int __init optidma_init(void)

drivers/ata/pata_pcmcia.c

@@ -62,7 +62,6 @@ static struct scsi_host_template pcmcia_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,

drivers/ata/pata_pdc2027x.c

@@ -134,7 +134,6 @@ static struct scsi_host_template pdc2027x_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -854,7 +853,7 @@ static void __devexit pdc2027x_remove_one(struct pci_dev *pdev)
  */
 static int __init pdc2027x_init(void)
 {
-	return pci_module_init(&pdc2027x_pci_driver);
+	return pci_register_driver(&pdc2027x_pci_driver);
 }
 
 /**

drivers/ata/pata_pdc202xx_old.c

@@ -21,7 +21,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "pata_pdc202xx_old"
-#define DRV_VERSION "0.2.1"
+#define DRV_VERSION "0.2.3"
 
 /**
  *	pdc2024x_pre_reset		-	probe begin
@@ -63,7 +63,7 @@ static void pdc2026x_error_handler(struct ata_port *ap)
 }
 
 /**
- *	pdc_configure_piomode	-	set chip PIO timing
+ *	pdc202xx_configure_piomode	-	set chip PIO timing
  *	@ap: ATA interface
  *	@adev: ATA device
  *	@pio: PIO mode
@@ -73,7 +73,7 @@ static void pdc2026x_error_handler(struct ata_port *ap)
  *	versa
  */
 
-static void pdc_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio)
+static void pdc202xx_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio)
 {
 	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 	int port = 0x60 + 4 * ap->port_no + 2 * adev->devno;
@@ -98,7 +98,7 @@ static void pdc_configure_piomode(struct ata_port *ap, struct ata_device *adev,
 }
 
 /**
- *	pdc_set_piomode	-	set initial PIO mode data
+ *	pdc202xx_set_piomode	-	set initial PIO mode data
  *	@ap: ATA interface
  *	@adev: ATA device
  *
@@ -106,13 +106,13 @@ static void pdc_configure_piomode(struct ata_port *ap, struct ata_device *adev,
  *	but we want to set the PIO timing by default.
  */
 
-static void pdc_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void pdc202xx_set_piomode(struct ata_port *ap, struct ata_device *adev)
 {
-	pdc_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
+	pdc202xx_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
 }
 
 /**
- *	pdc_configure_dmamode	-	set DMA mode in chip
+ *	pdc202xx_configure_dmamode	-	set DMA mode in chip
  *	@ap: ATA interface
  *	@adev: ATA device
  *
@@ -120,7 +120,7 @@ static void pdc_set_piomode(struct ata_port *ap, struct ata_device *adev)
  *	to occur.
  */
 
-static void pdc_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+static void pdc202xx_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 {
 	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 	int port = 0x60 + 4 * ap->port_no + 2 * adev->devno;
@@ -184,7 +184,7 @@ static void pdc2026x_bmdma_start(struct ata_queued_cmd *qc)
 
 	/* The DMA clocks may have been trashed by a reset. FIXME: make conditional
 	   and move to qc_issue ? */
-	pdc_set_dmamode(ap, qc->dev);
+	pdc202xx_set_dmamode(ap, qc->dev);
 
 	/* Cases the state machine will not complete correctly without help */
 	if ((tf->flags & ATA_TFLAG_LBA48) ||  tf->protocol == ATA_PROT_ATAPI_DMA)
@@ -254,7 +254,7 @@ static void pdc2026x_dev_config(struct ata_port *ap, struct ata_device *adev)
 	adev->max_sectors = 256;
 }
 
-static struct scsi_host_template pdc_sht = {
+static struct scsi_host_template pdc202xx_sht = {
 	.module			= THIS_MODULE,
 	.name			= DRV_NAME,
 	.ioctl			= ata_scsi_ioctl,
@@ -262,7 +262,6 @@ static struct scsi_host_template pdc_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -271,12 +270,14 @@ static struct scsi_host_template pdc_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations pdc2024x_port_ops = {
 	.port_disable	= ata_port_disable,
-	.set_piomode	= pdc_set_piomode,
-	.set_dmamode	= pdc_set_dmamode,
+	.set_piomode	= pdc202xx_set_piomode,
+	.set_dmamode	= pdc202xx_set_dmamode,
 	.mode_filter	= ata_pci_default_filter,
 	.tf_load	= ata_tf_load,
 	.tf_read	= ata_tf_read,
@@ -308,8 +309,8 @@ static struct ata_port_operations pdc2024x_port_ops = {
 
 static struct ata_port_operations pdc2026x_port_ops = {
 	.port_disable	= ata_port_disable,
-	.set_piomode	= pdc_set_piomode,
-	.set_dmamode	= pdc_set_dmamode,
+	.set_piomode	= pdc202xx_set_piomode,
+	.set_dmamode	= pdc202xx_set_dmamode,
 	.mode_filter	= ata_pci_default_filter,
 	.tf_load	= ata_tf_load,
 	.tf_read	= ata_tf_read,
@@ -340,11 +341,11 @@ static struct ata_port_operations pdc2026x_port_ops = {
 	.host_stop	= ata_host_stop
 };
 
-static int pdc_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 {
 	static struct ata_port_info info[3] = {
 		{
-			.sht = &pdc_sht,
+			.sht = &pdc202xx_sht,
 			.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
 			.pio_mask = 0x1f,
 			.mwdma_mask = 0x07,
@@ -352,7 +353,7 @@ static int pdc_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 			.port_ops = &pdc2024x_port_ops
 		},
 		{
-			.sht = &pdc_sht,
+			.sht = &pdc202xx_sht,
 			.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
 			.pio_mask = 0x1f,
 			.mwdma_mask = 0x07,
@@ -360,7 +361,7 @@ static int pdc_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 			.port_ops = &pdc2026x_port_ops
 		},
 		{
-			.sht = &pdc_sht,
+			.sht = &pdc202xx_sht,
 			.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
 			.pio_mask = 0x1f,
 			.mwdma_mask = 0x07,
@@ -386,7 +387,7 @@ static int pdc_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 	return ata_pci_init_one(dev, port_info, 2);
 }
 
-static const struct pci_device_id pdc[] = {
+static const struct pci_device_id pdc202xx[] = {
 	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20246), 0 },
 	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20262), 1 },
 	{ PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20263), 1 },
@@ -396,28 +397,30 @@ static const struct pci_device_id pdc[] = {
 	{ },
 };
 
-static struct pci_driver pdc_pci_driver = {
+static struct pci_driver pdc202xx_pci_driver = {
 	.name 		= DRV_NAME,
-	.id_table	= pdc,
-	.probe 		= pdc_init_one,
-	.remove		= ata_pci_remove_one
+	.id_table	= pdc202xx,
+	.probe 		= pdc202xx_init_one,
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= ata_pci_device_resume,
 };
 
-static int __init pdc_init(void)
+static int __init pdc202xx_init(void)
 {
-	return pci_register_driver(&pdc_pci_driver);
+	return pci_register_driver(&pdc202xx_pci_driver);
 }
 
-static void __exit pdc_exit(void)
+static void __exit pdc202xx_exit(void)
 {
-	pci_unregister_driver(&pdc_pci_driver);
+	pci_unregister_driver(&pdc202xx_pci_driver);
 }
 
 MODULE_AUTHOR("Alan Cox");
 MODULE_DESCRIPTION("low-level driver for Promise 2024x and 20262-20267");
 MODULE_LICENSE("GPL");
-MODULE_DEVICE_TABLE(pci, pdc);
+MODULE_DEVICE_TABLE(pci, pdc202xx);
 MODULE_VERSION(DRV_VERSION);
 
-module_init(pdc_init);
-module_exit(pdc_exit);
+module_init(pdc202xx_init);
+module_exit(pdc202xx_exit);

drivers/ata/pata_platform.c

+/*
+ * Generic platform device PATA driver
+ *
+ * Copyright (C) 2006  Paul Mundt
+ *
+ * Based on pata_pcmcia:
+ *
+ *   Copyright 2005-2006 Red Hat Inc <alan@redhat.com>, all rights reserved.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <scsi/scsi_host.h>
+#include <linux/ata.h>
+#include <linux/libata.h>
+#include <linux/platform_device.h>
+#include <linux/pata_platform.h>
+
+#define DRV_NAME "pata_platform"
+#define DRV_VERSION "0.1.2"
+
+static int pio_mask = 1;
+
+/*
+ * Provide our own set_mode() as we don't want to change anything that has
+ * already been configured..
+ */
+static void pata_platform_set_mode(struct ata_port *ap)
+{
+	int i;
+
+	for (i = 0; i < ATA_MAX_DEVICES; i++) {
+		struct ata_device *dev = &ap->device[i];
+
+		if (ata_dev_enabled(dev)) {
+			/* We don't really care */
+			dev->pio_mode = dev->xfer_mode = XFER_PIO_0;
+			dev->xfer_shift = ATA_SHIFT_PIO;
+			dev->flags |= ATA_DFLAG_PIO;
+		}
+	}
+}
+
+static void pata_platform_host_stop(struct ata_host *host)
+{
+	int i;
+
+	/*
+	 * Unmap the bases for MMIO
+	 */
+	for (i = 0; i < host->n_ports; i++) {
+		struct ata_port *ap = host->ports[i];
+
+		if (ap->flags & ATA_FLAG_MMIO) {
+			iounmap((void __iomem *)ap->ioaddr.ctl_addr);
+			iounmap((void __iomem *)ap->ioaddr.cmd_addr);
+		}
+	}
+}
+
+static struct scsi_host_template pata_platform_sht = {
+	.module			= THIS_MODULE,
+	.name			= DRV_NAME,
+	.ioctl			= ata_scsi_ioctl,
+	.queuecommand		= ata_scsi_queuecmd,
+	.can_queue		= ATA_DEF_QUEUE,
+	.this_id		= ATA_SHT_THIS_ID,
+	.sg_tablesize		= LIBATA_MAX_PRD,
+	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
+	.emulated		= ATA_SHT_EMULATED,
+	.use_clustering		= ATA_SHT_USE_CLUSTERING,
+	.proc_name		= DRV_NAME,
+	.dma_boundary		= ATA_DMA_BOUNDARY,
+	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
+	.bios_param		= ata_std_bios_param,
+};
+
+static struct ata_port_operations pata_platform_port_ops = {
+	.set_mode		= pata_platform_set_mode,
+
+	.port_disable		= ata_port_disable,
+	.tf_load		= ata_tf_load,
+	.tf_read		= ata_tf_read,
+	.check_status		= ata_check_status,
+	.exec_command		= ata_exec_command,
+	.dev_select		= ata_std_dev_select,
+
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= ata_bmdma_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
+
+	.qc_prep		= ata_qc_prep,
+	.qc_issue		= ata_qc_issue_prot,
+
+	.data_xfer		= ata_pio_data_xfer_noirq,
+
+	.irq_handler		= ata_interrupt,
+	.irq_clear		= ata_bmdma_irq_clear,
+
+	.port_start		= ata_port_start,
+	.port_stop		= ata_port_stop,
+	.host_stop		= pata_platform_host_stop
+};
+
+static void pata_platform_setup_port(struct ata_ioports *ioaddr,
+				     struct pata_platform_info *info)
+{
+	unsigned int shift = 0;
+
+	/* Fixup the port shift for platforms that need it */
+	if (info && info->ioport_shift)
+		shift = info->ioport_shift;
+
+	ioaddr->data_addr	= ioaddr->cmd_addr + (ATA_REG_DATA    << shift);
+	ioaddr->error_addr	= ioaddr->cmd_addr + (ATA_REG_ERR     << shift);
+	ioaddr->feature_addr	= ioaddr->cmd_addr + (ATA_REG_FEATURE << shift);
+	ioaddr->nsect_addr	= ioaddr->cmd_addr + (ATA_REG_NSECT   << shift);
+	ioaddr->lbal_addr	= ioaddr->cmd_addr + (ATA_REG_LBAL    << shift);
+	ioaddr->lbam_addr	= ioaddr->cmd_addr + (ATA_REG_LBAM    << shift);
+	ioaddr->lbah_addr	= ioaddr->cmd_addr + (ATA_REG_LBAH    << shift);
+	ioaddr->device_addr	= ioaddr->cmd_addr + (ATA_REG_DEVICE  << shift);
+	ioaddr->status_addr	= ioaddr->cmd_addr + (ATA_REG_STATUS  << shift);
+	ioaddr->command_addr	= ioaddr->cmd_addr + (ATA_REG_CMD     << shift);
+}
+
+/**
+ *	pata_platform_probe		-	attach a platform interface
+ *	@pdev: platform device
+ *
+ *	Register a platform bus IDE interface. Such interfaces are PIO and we
+ *	assume do not support IRQ sharing.
+ *
+ *	Platform devices are expected to contain 3 resources per port:
+ *
+ *		- I/O Base (IORESOURCE_IO or IORESOURCE_MEM)
+ *		- CTL Base (IORESOURCE_IO or IORESOURCE_MEM)
+ *		- IRQ	   (IORESOURCE_IRQ)
+ *
+ *	If the base resources are both mem types, the ioremap() is handled
+ *	here. For IORESOURCE_IO, it's assumed that there's no remapping
+ *	necessary.
+ */
+static int __devinit pata_platform_probe(struct platform_device *pdev)
+{
+	struct resource *io_res, *ctl_res;
+	struct ata_probe_ent ae;
+	unsigned int mmio;
+	int ret;
+
+	/*
+	 * Simple resource validation ..
+	 */
+	if (unlikely(pdev->num_resources != 3)) {
+		dev_err(&pdev->dev, "invalid number of resources\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * Get the I/O base first
+	 */
+	io_res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+	if (io_res == NULL) {
+		io_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		if (unlikely(io_res == NULL))
+			return -EINVAL;
+	}
+
+	/*
+	 * Then the CTL base
+	 */
+	ctl_res = platform_get_resource(pdev, IORESOURCE_IO, 1);
+	if (ctl_res == NULL) {
+		ctl_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+		if (unlikely(ctl_res == NULL))
+			return -EINVAL;
+	}
+
+	/*
+	 * Check for MMIO
+	 */
+	mmio = (( io_res->flags == IORESOURCE_MEM) &&
+		(ctl_res->flags == IORESOURCE_MEM));
+
+	/*
+	 * Now that that's out of the way, wire up the port..
+	 */
+	memset(&ae, 0, sizeof(struct ata_probe_ent));
+	INIT_LIST_HEAD(&ae.node);
+	ae.dev = &pdev->dev;
+	ae.port_ops = &pata_platform_port_ops;
+	ae.sht = &pata_platform_sht;
+	ae.n_ports = 1;
+	ae.pio_mask = pio_mask;
+	ae.irq = platform_get_irq(pdev, 0);
+	ae.irq_flags = 0;
+	ae.port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST;
+
+	/*
+	 * Handle the MMIO case
+	 */
+	if (mmio) {
+		ae.port_flags |= ATA_FLAG_MMIO;
+
+		ae.port[0].cmd_addr = (unsigned long)ioremap(io_res->start,
+				io_res->end - io_res->start + 1);
+		if (unlikely(!ae.port[0].cmd_addr)) {
+			dev_err(&pdev->dev, "failed to remap IO base\n");
+			return -ENXIO;
+		}
+
+		ae.port[0].ctl_addr = (unsigned long)ioremap(ctl_res->start,
+				ctl_res->end - ctl_res->start + 1);
+		if (unlikely(!ae.port[0].ctl_addr)) {
+			dev_err(&pdev->dev, "failed to remap CTL base\n");
+			ret = -ENXIO;
+			goto bad_remap;
+		}
+	} else {
+		ae.port[0].cmd_addr = io_res->start;
+		ae.port[0].ctl_addr = ctl_res->start;
+	}
+
+	ae.port[0].altstatus_addr = ae.port[0].ctl_addr;
+
+	pata_platform_setup_port(&ae.port[0], pdev->dev.platform_data);
+
+	if (unlikely(ata_device_add(&ae) == 0)) {
+		ret = -ENODEV;
+		goto add_failed;
+	}
+
+	return 0;
+
+add_failed:
+	if (ae.port[0].ctl_addr && mmio)
+		iounmap((void __iomem *)ae.port[0].ctl_addr);
+bad_remap:
+	if (ae.port[0].cmd_addr && mmio)
+		iounmap((void __iomem *)ae.port[0].cmd_addr);
+
+	return ret;
+}
+
+/**
+ *	pata_platform_remove	-	unplug a platform interface
+ *	@pdev: platform device
+ *
+ *	A platform bus ATA device has been unplugged. Perform the needed
+ *	cleanup. Also called on module unload for any active devices.
+ */
+static int __devexit pata_platform_remove(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct ata_host *host = dev_get_drvdata(dev);
+
+	ata_host_remove(host);
+	dev_set_drvdata(dev, NULL);
+
+	return 0;
+}
+
+static struct platform_driver pata_platform_driver = {
+	.probe		= pata_platform_probe,
+	.remove		= __devexit_p(pata_platform_remove),
+	.driver = {
+		.name		= DRV_NAME,
+		.owner		= THIS_MODULE,
+	},
+};
+
+static int __init pata_platform_init(void)
+{
+	return platform_driver_register(&pata_platform_driver);
+}
+
+static void __exit pata_platform_exit(void)
+{
+	platform_driver_unregister(&pata_platform_driver);
+}
+module_init(pata_platform_init);
+module_exit(pata_platform_exit);
+
+module_param(pio_mask, int, 0);
+
+MODULE_AUTHOR("Paul Mundt");
+MODULE_DESCRIPTION("low-level driver for platform device ATA");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);

drivers/ata/pata_qdi.c

@@ -157,7 +157,6 @@ static struct scsi_host_template qdi_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,

drivers/ata/pata_radisys.c

@@ -220,7 +220,6 @@ static struct scsi_host_template radisys_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -229,6 +228,8 @@ static struct scsi_host_template radisys_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static const struct ata_port_operations radisys_pata_ops = {
@@ -311,6 +312,8 @@ static struct pci_driver radisys_pci_driver = {
 	.id_table		= radisys_pci_tbl,
 	.probe			= radisys_init_one,
 	.remove			= ata_pci_remove_one,
+	.suspend		= ata_pci_device_suspend,
+	.resume			= ata_pci_device_resume,
 };
 
 static int __init radisys_init(void)

drivers/ata/pata_rz1000.c

@@ -21,7 +21,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"pata_rz1000"
-#define DRV_VERSION	"0.2.2"
+#define DRV_VERSION	"0.2.3"
 
 
 /**
@@ -83,7 +83,6 @@ static struct scsi_host_template rz1000_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -92,6 +91,8 @@ static struct scsi_host_template rz1000_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations rz1000_port_ops = {
@@ -129,6 +130,19 @@ static struct ata_port_operations rz1000_port_ops = {
 	.host_stop	= ata_host_stop
 };
 
+static int rz1000_fifo_disable(struct pci_dev *pdev)
+{
+	u16 reg;
+	/* Be exceptionally paranoid as we must be sure to apply the fix */
+	if (pci_read_config_word(pdev, 0x40, &reg) != 0)
+		return -1;
+	reg &= 0xDFFF;
+	if (pci_write_config_word(pdev, 0x40, reg) != 0)
+		return -1;
+	printk(KERN_INFO DRV_NAME ": disabled chipset readahead.\n");
+	return 0;
+}
+
 /**
  *	rz1000_init_one - Register RZ1000 ATA PCI device with kernel services
  *	@pdev: PCI device to register
@@ -143,7 +157,6 @@ static int rz1000_init_one (struct pci_dev *pdev, const struct pci_device_id *en
 {
 	static int printed_version;
 	struct ata_port_info *port_info[2];
-	u16 reg;
 	static struct ata_port_info info = {
 		.sht = &rz1000_sht,
 		.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
@@ -154,23 +167,25 @@ static int rz1000_init_one (struct pci_dev *pdev, const struct pci_device_id *en
 	if (!printed_version++)
 		printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
 
-	/* Be exceptionally paranoid as we must be sure to apply the fix */
-	if (pci_read_config_word(pdev, 0x40, &reg) != 0)
-		goto fail;
-	reg &= 0xDFFF;
-	if (pci_write_config_word(pdev, 0x40, reg) != 0)
-		goto fail;
-	printk(KERN_INFO DRV_NAME ": disabled chipset readahead.\n");
-
-	port_info[0] = &info;
-	port_info[1] = &info;
-	return ata_pci_init_one(pdev, port_info, 2);
-fail:
+	if (rz1000_fifo_disable(pdev) == 0) {
+		port_info[0] = &info;
+		port_info[1] = &info;
+		return ata_pci_init_one(pdev, port_info, 2);
+	}
 	printk(KERN_ERR DRV_NAME ": failed to disable read-ahead on chipset..\n");
 	/* Not safe to use so skip */
 	return -ENODEV;
 }
 
+static int rz1000_reinit_one(struct pci_dev *pdev)
+{
+	/* If this fails on resume (which is a "cant happen" case), we
+	   must stop as any progress risks data loss */
+	if (rz1000_fifo_disable(pdev))
+		panic("rz1000 fifo");
+	return ata_pci_device_resume(pdev);
+}
+
 static const struct pci_device_id pata_rz1000[] = {
 	{ PCI_VDEVICE(PCTECH, PCI_DEVICE_ID_PCTECH_RZ1000), },
 	{ PCI_VDEVICE(PCTECH, PCI_DEVICE_ID_PCTECH_RZ1001), },
@@ -182,7 +197,9 @@ static struct pci_driver rz1000_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= pata_rz1000,
 	.probe 		= rz1000_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= rz1000_reinit_one,
 };
 
 static int __init rz1000_init(void)

drivers/ata/pata_sc1200.c

@@ -40,7 +40,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"sc1200"
-#define DRV_VERSION	"0.2.3"
+#define DRV_VERSION	"0.2.4"
 
 #define SC1200_REV_A	0x00
 #define SC1200_REV_B1	0x01
@@ -186,7 +186,6 @@ static struct scsi_host_template sc1200_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -195,6 +194,8 @@ static struct scsi_host_template sc1200_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations sc1200_port_ops = {
@@ -264,7 +265,9 @@ static struct pci_driver sc1200_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= sc1200,
 	.probe 		= sc1200_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= ata_pci_device_resume,
 };
 
 static int __init sc1200_init(void)

drivers/ata/pata_sis.c

@@ -34,7 +34,7 @@
 #include <linux/ata.h>
 
 #define DRV_NAME	"pata_sis"
-#define DRV_VERSION	"0.4.4"
+#define DRV_VERSION	"0.4.5"
 
 struct sis_chipset {
 	u16 device;			/* PCI host ID */
@@ -538,7 +538,6 @@ static struct scsi_host_template sis_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -547,6 +546,8 @@ static struct scsi_host_template sis_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static const struct ata_port_operations sis_133_ops = {
@@ -1000,6 +1001,8 @@ static struct pci_driver sis_pci_driver = {
 	.id_table		= sis_pci_tbl,
 	.probe			= sis_init_one,
 	.remove			= ata_pci_remove_one,
+	.suspend		= ata_pci_device_suspend,
+	.resume			= ata_pci_device_resume,
 };
 
 static int __init sis_init(void)

drivers/ata/pata_sl82c105.c

@@ -230,7 +230,6 @@ static struct scsi_host_template sl82c105_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,