Trying quirks in usbcore needs to rebuild the driver or the entire
kernel if it's builtin. It can save a lot of time if usbcore has similar
ability like "usbhid.quirks=" and "usb-storage.quirks=".

Rename the original quirk detection function to "static" as we introduce
this new "dynamic" function.

Now users can use "usbcore.quirks=" as short term workaround before the
next kernel release. Also, the quirk parameter can XOR the builtin
quirks for debugging purpose.

This is inspired by usbhid and usb-storage.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Update to show Minas Harutyunyan as the new maintainer for dwc2.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The maximum bytes per interval for USB SuperSpeed Plus can be set by
isoc endpoint companion descriptor when it is above 48K. If the
descriptor is provided, then use its value.

USB 3.1 spec 9.6.8
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'phy-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

phy: for 4.17

 *) Add USB PHY driver for MDM6600 on Droid
 *) Add USB PHY driver for STM32 USB PHY Controller
 *) Add inno-usb2-phy driver for hi3798cv200 SoC
 *) Add combo phy driver (SATA/USB/PCIE) for HiSilicon STB SoCs
 *) Add USB3 PHY driver for Meson GXL and GXM
 *) Add support for R8A77965 Gen3 USB 2.0 PHY in phy-rcar-gen3-usb2 driver
 *) Add support for qualcomm QUSB2 V2 and QMP V3 USB3 PHY in phy-qcom-qusb2
    and phy-qcom-qmp PHY driver respectively
 *) Add support for runtime PM in phy-qcom-qusb2 and phy-qcom-qmp PHY drivers
 *) Add support for Allwinner R40 USB PHY in sun4i-usb PHY driver
 *) Add support in rockchip-typec PHY driver to make extcon optional and
    fallback to working in host mode if extcon is missing
 *) Add support in rockchip-typec PHY driver to mux PHYs connected to DP
 *) Add support to configure slew rate parameters in phy-mtk-tphy PHY driver
 *) Add workaround for missing Vbus det interrupts on Allwinner A23/A33
 *) Add USB speed related PHY modes in phy core
 *) Fix PHY 'structure' documentation
 *) Force rockchip-typec PHY to USB2 if DP-only mode is used
 *) Fix phy-qcom-qusb2 and phy-qcom-qmp PHY drivers to follow PHY reset and
    initialization sequence as per hardware programming manual
 *) Fix Marvell BG2CD SoC USB failure in phy-berlin-usb driver
 *) Minor fixes in lpc18xx-usb-otg, xusb-tegra210 and phy-rockchip-emmc PHY
    drivers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull x86/pti updates from Thomas Gleixner:
 "Another set of melted spectrum updates:

   - Iron out the last late microcode loading issues by actually
     checking whether new microcode is present and preventing the CPU
     synchronization to run into a timeout induced hang.

   - Remove Skylake C2 from the microcode blacklist according to the
     latest Intel documentation

   - Fix the VM86 POPF emulation which traps if VIP is set, but VIF is
     not. Enhance the selftests to catch that kind of issue

   - Annotate indirect calls/jumps for objtool on 32bit. This is not a
     functional issue, but for consistency sake its the right thing to
     do.

   - Fix a jump label build warning observed on SPARC64 which uses 32bit
     storage for the code location which is casted to 64 bit pointer w/o
     extending it to 64bit first.

   - Add two new cpufeature bits. Not really an urgent issue, but
     provides them for both x86 and x86/kvm work. No impact on the
     current kernel"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/microcode: Fix CPU synchronization routine
  x86/microcode: Attempt late loading only when new microcode is present
  x86/speculation: Remove Skylake C2 from Speculation Control microcode blacklist
  jump_label: Fix sparc64 warning
  x86/speculation, objtool: Annotate indirect calls/jumps for objtool on 32-bit kernels
  x86/vm86/32: Fix POPF emulation
  selftests/x86/entry_from_vm86: Add test cases for POPF
  selftests/x86/entry_from_vm86: Exit with 1 if we fail
  x86/cpufeatures: Add Intel PCONFIG cpufeature
  x86/cpufeatures: Add Intel Total Memory Encryption cpufeature

Pull x86 fix from Thomas Gleixner:
 "A single fix for vmalloc_fault() which uses p*d_huge() unconditionally
  whether CONFIG_HUGETLBFS is set or not. In case of CONFIG_HUGETLBFS=n
  this results in a crash as p*d_huge() returns 0 in that case"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Fix vmalloc_fault to use pXd_large

Pull irq fixes from Thomas Gleixner:
 "Three fixes for irq chip drivers:

   - Make sure the allocations in the GIC-V3 ITS driver are large enough
     to accomodate the interrupt space

   - Fix a misplaced __iomem annotation which causes a splat of 26
     sparse warnings

   - Remove an unused function in the IMX GPCV2 driver which causes
     build warnings"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/irq-imx-gpcv2: Remove unused function
  irqchip/gic-v3-its: Ensure nr_ites >= nr_lpis
  irqchip/gic-v3-its: Fix misplaced __iomem annotations

Pull EFI fix from Thomas Gleixner:
 "A single fix to prevent partially initialized pointers in mixed mode
  (64bit kernel on 32bit UEFI)"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/libstub/tpm: Initialize pointer variables to zero for mixed mode

Pull KVM fixes from Paolo Bonzini:
 "PPC:
   - fix bug leading to lost IPIs and smp_call_function_many() lockups
     on POWER9

  ARM:
   - locking fix
   - reset fix
   - GICv2 multi-source SGI injection fix
   - GICv2-on-v3 MMIO synchronization fix
   - make the console less verbose.

  x86:
   - fix device passthrough on AMD SME"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: Fix device passthrough when SME is active
  kvm: arm/arm64: vgic-v3: Tighten synchronization for guests using v2 on v3
  KVM: arm/arm64: vgic: Don't populate multiple LRs with the same vintid
  KVM: arm/arm64: Reduce verbosity of KVM init log
  KVM: arm/arm64: Reset mapped IRQs on VM reset
  KVM: arm/arm64: Avoid vcpu_load for other vcpu ioctls than KVM_RUN
  KVM: arm/arm64: vgic: Add missing irq_lock to vgic_mmio_read_pending
  KVM: PPC: Book3S HV: Fix trap number return from __kvmppc_vcore_entry

Just when I had decided that flush_cache_range() was always called with
a valid context, Helge reported two cases where the
"BUG_ON(!vma->vm_mm->context);" was hit on the phantom buildd:

 kernel BUG at /mnt/sdb6/linux/linux-4.15.4/arch/parisc/kernel/cache.c:587!
 CPU: 1 PID: 3254 Comm: kworker/1:2 Tainted: G D 4.15.0-1-parisc64-smp #1 Debian 4.15.4-1+b1
 Workqueue: events free_ioctx
  IAOQ[0]: flush_cache_range+0x164/0x168
  IAOQ[1]: flush_cache_page+0x0/0x1c8
  RP(r2): unmap_page_range+0xae8/0xb88
 Backtrace:
  [<00000000404a6980>] unmap_page_range+0xae8/0xb88
  [<00000000404a6ae0>] unmap_single_vma+0xc0/0x188
  [<00000000404a6cdc>] zap_page_range_single+0x134/0x1f8
  [<00000000404a702c>] unmap_mapping_range+0x1cc/0x208
  [<0000000040461518>] truncate_pagecache+0x98/0x108
  [<0000000040461624>] truncate_setsize+0x9c/0xb8
  [<00000000405d7f30>] put_aio_ring_file+0x80/0x100
  [<00000000405d803c>] aio_free_ring+0x8c/0x290
  [<00000000405d82c0>] free_ioctx+0x80/0x180
  [<0000000040284e6c>] process_one_work+0x21c/0x668
  [<00000000402854c4>] worker_thread+0x20c/0x778
  [<0000000040291d44>] kthread+0x2d4/0x2e0
  [<0000000040204020>] end_fault_vector+0x20/0xc0

This indicates that we need to handle the no context case in
flush_cache_range() as we do in flush_cache_mm().

In thinking about this, I realized that we don't need to flush the TLB
when there is no context.  So, I added context checks to the large flush
cases in flush_cache_mm() and flush_cache_range().  The large flush case
occurs frequently in flush_cache_mm() and the change should improve fork
performance.

The v2 version of this change removes the BUG_ON from flush_cache_page()
by skipping the TLB flush when there is no context.  I also added code
to flush the TLB in flush_cache_mm() and flush_cache_range() when we
have a context that's not current.  Now all three routines handle TLB
flushes in a similar manner.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Helge Deller <deller@gmx.de>

Pull btrfs fixes from David Sterba:
 "There's an important revert in this pull request that needs to go to
  stable as it causes a corruption on big endian machines.

  The other fix is for FIEMAP incorrectly reporting shared extents
  before a sync and one fix for a crash in raid56.

  So far we got only one report about the BE corruption, the stable
  kernels were out for like a week, so hopefully the scope of the damage
  is low"

* tag 'for-4.16-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Revert "btrfs: use proper endianness accessors for super_copy"
  btrfs: add missing initialization in btrfs_check_shared
  btrfs: Fix NULL pointer exception in find_bio_stripe

Pull microblaze fixes from Michal Simek:

 - Use NO_BOOTMEM to fix boot issue

 - Fix opt lib endian dependencies

* tag 'microblaze-4.16-rc6' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: switch to NO_BOOTMEM
  microblaze: remove unused alloc_maybe_bootmem
  microblaze: Setup dependencies for ASM optimized lib functions

Emanuel reported an issue with a hang during microcode update because my
dumb idea to use one atomic synchronization variable for both rendezvous
- before and after update - was simply bollocks:

  microcode: microcode_reload_late: late_cpus: 4
  microcode: __reload_late: cpu 2 entered
  microcode: __reload_late: cpu 1 entered
  microcode: __reload_late: cpu 3 entered
  microcode: __reload_late: cpu 0 entered
  microcode: __reload_late: cpu 1 left
  microcode: Timeout while waiting for CPUs rendezvous, remaining: 1

CPU1 above would finish, leave and the others will still spin waiting for
it to join.

So do two synchronization atomics instead, which makes the code a lot more
straightforward.

Also, since the update is serialized and it also takes quite some time per
microcode engine, increase the exit timeout by the number of CPUs on the
system.

That's ok because the moment all CPUs are done, that timeout will be cut
short.

Furthermore, panic when some of the CPUs timeout when returning from a
microcode update: we can't allow a system with not all cores updated.

Also, as an optimization, do not do the exit sync if microcode wasn't
updated.
Reported-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/20180314183615.17629-2-bp@alien8.de

Return UCODE_NEW from the scanning functions to denote that new microcode
was found and only then attempt the expensive synchronization dance.
Reported-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/20180314183615.17629-1-bp@alien8.de

Pull drm fixes from Dave Airlie:
 "i915, amd and nouveau fixes.

  i915:
   - backlight fix for some panels
   - pm fix
   - fencing fix
   - some GVT fixes

  amdgpu:
   - backlight fix across suspend/resume
   - object destruction ordering issue fix
   - displayport fix

  nouveau:
   - two backlight fixes
   - fix for some lockups

  Pretty quiet week, seems like everyone was fixing backlights"

* tag 'drm-fixes-for-v4.16-rc6' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau/bl: fix backlight regression
  drm/nouveau/bl: Fix oops on driver unbind
  drm/nouveau/mmu: ALIGN_DOWN correct variable
  drm/i915/gvt: fix user copy warning by whitelist workload rb_tail field
  drm/i915/gvt: Correct the privilege shadow batch buffer address
  drm/amdgpu/dce: Don't turn off DP sink when disconnected
  drm/amdgpu: save/restore backlight level in legacy dce code
  drm/radeon: fix prime teardown order
  drm/amdgpu: fix prime teardown order
  drm/i915: Kick the rps worker when changing the boost frequency
  drm/i915: Only prune fences after wait-for-all
  drm/i915: Enable VBT based BL control for DP
  drm/i915/gvt: keep oa config in shadow ctx
  drm/i915/gvt: Add runtime_pm_get/put into gvt_switch_mmio

In preparation to enabling -Wvla, remove VLA and replace it
with dynamic memory allocation instead.

The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
or a security flaw. Also, in general, as code evolves it is easy to
lose track of how big a VLA can get. Thus, we can end up having runtime
failures that are hard to debug.

Also, fixed as part of the directive to remove all VLAs from
the kernel: https://lkml.org/lkml/2018/3/7/621

Notice that in this particular case, an alternative to kzalloc is kcalloc,
in which case the code would look as follows instead:

iv = kcalloc(crypto_skcipher_ivsize(tfm_cbc), sizeof(*iv), GFP_KERNEL);

but if the data type of _iv_ never changes, or the type size is always one
byte, kzalloc is good enough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci driver displays the supported xHC USB revision in a message during
driver load:

"Host supports USB 3.1 Enhanced SuperSpeed"

Get the USB minor revision number from the xhci protocol capability.
This will show the correct supported revisions for new USB 3.2 and later
hosts

Don't rely on the SBRN (serial bus revision number) register, it's often
showing 0x30 (USB3.0) for hosts that support USB 3.1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some devices use a clear endpoint halt request as a soft reset, even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side.

xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host
side toggle and sequence, and get it in sync with the device side.

This is a respin of a old patch that was reverted as it had a stale
endpoint context dequeue value which caused regression.
commit 27082e26 ("xhci: Clear the host side toggle manually when
endpoint is 'soft reset'")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

make the local ep_state variable a pointer to the actual ring ep_state.
This allows us to read fresh ep_state values every time, will be useful
later.

Also move the streams check out from bulk only case. Even if only
bulk tranfers can use streams we shouldn't continue if those flags
are set. Main reason for this change is really code readability and
grouping functionality
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The default stop endpoint completion handler will give back cancelled
URBs, and clean, or move past those canceller TRBs on the ring.

This is not always the preferred action.

If the stop endpoint command issuer is waiting for a completion
skip the default handler and just call the completion.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

set udev->slot_id to zero when disabling and freeing the xhci slot.
Prevents usb core from calling xhci with a stale slot id.

xHC controller may be reset during resume to recover from some error.
All slots are unusable as they are disabled and freed.
xhci driver starts slot enumeration again from 1 in the order they are
enabled. In the worst case a stale udev->slot_id for one device matches
a newly enabled slot_id for a different device, causing us to
perform a action on the wrong device.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Function argument ep_trb for finish_td() isn't needed anymore.
Cleanup it.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Function argument ep_trb for xhci_cleanup_halted_endpoint() isn't
needed anymore. Cleanup it.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty_port_register_device() returns error pointers on error, never NULL.
The IS_ERR_OR_NULL() function returns either 1 or 0 so it means we
return 1 on error instead of a proper error code.  The caller only
checks for zero vs non-zero so this doesn't affect runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 3c181c12.

The offending patch was merged in 4.16-rc4 and was promptly applied to
stable kernels 4.14.25 and 4.15.8.

The patch causes a corruption in several superblock items on big-endian
machines because of messed up endianity conversions. The damage is
manually repairable. A filesystem cannot be mounted again after it has
been unmounted once.

We do a full revert and not a fixup so stable can pick that patch ASAP.

Fixes: 3c181c12 ("btrfs: use proper endianness accessors for super_copy")
Link: https://lkml.kernel.org/r/1521139304@msgid.manchmal.in-ulm.de
CC: stable@vger.kernel.org # 4.14+
Reported-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Signed-off-by: David Sterba <dsterba@suse.com>

When using device passthrough with SME active, the MMIO range that is
mapped for the device should not be mapped encrypted.  Add a check in
set_spte() to insure that a page is not mapped encrypted if that page
is a device MMIO page as indicated by kvm_is_mmio_pfn().

Cc: <stable@vger.kernel.org> # 4.14.x-
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Microblaze doesn't set CONFIG_NO_BOOTMEM and so memblock_virt_alloc()
doesn't work for CONFIG_HAVE_MEMBLOCK && !CONFIG_NO_BOOTMEM.

Similar change was already done by others architectures
"ARM: mm: Remove bootmem code and switch to NO_BOOTMEM"
(sha1: 84f452b1)
or
"openrisc: Consolidate setup to use memblock instead of bootmem"
(sha1: 266c7fad)
or
"parisc: Drop bootmem and switch to memblock"
(sha1: 4fe9e1d9)
or
"powerpc: Remove bootmem allocator"
(sha1: 10239733)
or
"s390/mm: Convert bootmem to memblock"
(sha1: 50be6345)
or
"sparc64: Convert over to NO_BOOTMEM."
(sha1: 625d693e)
or
"xtensa: drop sysmem and switch to memblock"
(sha1: 0e46c111)

Issue was introduced by:
"of/fdt: use memblock_virt_alloc for early alloc"
(sha1: 0fa1c579)
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

alloc_maybe_bootmem is unused, so remove it.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The patch:
"microblaze: Setup proper dependency for optimized lib functions"
(sha1: 7b6ce52b)
didn't setup all dependencies properly.
Optimized lib functions in C are also present for little endian
and optimized library functions in assembler are implemented only for
big endian version.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

In accordance with Intel's microcode revision guidance from March 6 MCU
rev 0xc2 is cleared on both Skylake H/S and Skylake Xeon E3 processors
that share CPUID 506E3.
Signed-off-by: Alexander Sergeyev <sergeev917@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jia Zhang <qianyue.zj@alibaba-inc.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kyle Huey <me@kylehuey.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/20180313193856.GA8580@localhost.localdomain

The reason why this was originally commented out is no longer clear. The
UPHY driver for SATA works fine with or without this change. The reset
value of the XDIGCLK_EN bit is 0, so unless programmed by the bootloader
this shouldn't make a difference anyway.

Define a macro for this bit and uncomment the code. This also fixes a
coverity issue brought to my attention by Rohith because not only is the
XDIGCLK_EN field modification commented out, but also the register write
which causes none of the earlier modifications of the register value to
be written to the register and the value being overwritten.
Reported-by: Rohith Seelaboyina <rseelaboyina@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Right now the rockchip type-c phy does fail probing when no extcon is
detected. Some boards get the cable-state via the extcon interface and
have this supported, other boards seem to use the fusb302 chip or
another but the driver currently does not seem to utilize the extcon
interface to report the cable-state. And, other, just connect the type-c
to a standard USB-A port so use no controller at all. A missing extcon
shouldn't fail to probe, instead, should just fall back to working in
host-mode if it cannot get the extcon.

Fixes: c301b327 ("arm64: dts: rockchip: add usb3-phy otg-port support for rk3399")
Reported-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The extcon property is used to detect the cable-state but some boards
just connect the type-c phy to a regular USB-A connector without any
power-delivery and thus no controller reporting the cable-state.
So the extcon property is not really a required property, move it to be
optional instead.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

There are 2 Type-c PHYs in RK3399, but only one DP controller. Hence
only one PHY can connect to DP controller at one time, the other should
be disconnected. The GRF_SOC_CON26 register has a switch bit to do it,
set this bit means enable PHY 1, clear this bit means enable PHY 0.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The usb3tousb2_en BIT will be clear to 0 in probe(), it make USB
controller work at USB3 mode, and if the USB phy is turned on with DP
only mode(4 lanes DP), the rockchip_usb3_phy_power_on() will return
directly, so usb3_host_disable and usb3_host_port these 2 BIT will keep
a same value as coreboot. In coreboot, these 3 BITs are set as USB2
mode, but now one of the bits is changed to USB3, it make USB controller
work at a unknown status.

These 3 BITs should be changed to USB2, if the Type-C works at 4 lanes
mode, and then switch it back to USB3 mode, when USB disconnect.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

We have forced usb3 to work in usb2 only mode in firmware by setting
usb3tousb2_en (bit3 of GRF_USB3PHY0/1_CON0) to 1, and setting
host_u3_port_disable (bit0 of GRF_USB3OTG0/1_CON1) to 1 and host_u3_port
(bit15~12 of GRF_USB3OTG0/1_CON1) to 0. So we need to re-enable usb3
host.

Note that the RK3399 TRM suggests that we should keep the whole usb3
controller in reset for the duration of the Type-C PHY initialization.
However, it's hard to assert the reset in the current framework of
reset. And according to the TRM, it doesn't require that we should
clear the usb3tousb2 bit before pipe ready. So let's enable the usb3
host after pipe ready to avoid the Type-C PHY initialization failure.
Signed-off-by: William wu <wulf@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

As now the following register properties are in the driver, document as
deprecated these properties and recommend to not use them on new bindings.

The deprecated properties are:

- rockchip,typec-conn-dir : the register of type-c connector direction
- rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2
                           enable control.
- rockchip,external-psm : the register of type-c phy external psm clock
                          selection.
- rockchip,pipe-status : the register of type-c phy pipe status.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>