Since timestamp in beacon buffer keeps changing all the time,
the memcmp check in mwifiex_save_curr_bcn() is redundant.
Remove that memcmp check and also avoid freeing and allocation
of buffer if required beacon buffer size is same as previous one.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1) Initialise HT capabilities in cfg80211 properly.
2) Cfg80211 stack may modify "sband->ht_cap" to disable
40Mhz operation in 2.4GHz band (after recent patch
"cfg80211: module_param to disable HT40 in 2.4GHz band")
Therefore read "sband->ht_cap" instead of an adapter variable
"hw_dot_11n_dev_cap" to get HT capabilities.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There are some SD8787 cards which don't support 5GHz band.
Therefore initialise 5GHz band parameters only if hardware
supports the band.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

AFAICT, this driver is claiming that 24 bits of rate info fit into a
16-bit field in the Tx descriptor.  Anyway, the use of bitfields is
frowned-upon for a variety of well-documented reasons...
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In xmit path, devices that do full hardware crypto (including
TKIP MMIC) need no tailroom. For such devices, tailroom
reservation can be skipped if all the keys are programmed into
the hardware (i.e software crypto is not used for any of the
keys) and none of the keys wants software to generate Michael
MIC.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This callback is used to set the minimum rate for management
frames.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds WMI_BITRATE_MASK_CMDID which can be
used by the set_bitrate_mask() handler.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bump the firmware version to 1.2
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds a new API for setting a TX rate mask in
drivers that have rate control in either the firmware or hardware.
This can be used for various purposes, for example, masking out the
11b rates in P2P operation.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Convert all libertas/ files to use kernel-doc notation instead
of whatever it was (doxygen?).

Add or fix function parameters in several places.

Use expected style for multi-line comments in lots of places.

Remove erroneous /** in multiple places.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In AP mode we register for the MAX_TX_RETRY and INACTIVE_STA events.
Both are reported to the upper layers as a TX failure in the offending
stations.

In STA mode we register only for the MAX_TX_RETRY event. A TX failure is
interpreted as a loss of connection.

Support for IEEE80211_HW_REPORTS_TX_ACK_STATUS has been removed to avoid
the inherent race condition of a mac80211 TX failure counter in addition
to the FW counter.

This patch depends on "mac80211: allow low level driver to report packet
loss"
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use ps wrappers before accessing hw registers in btcoex.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Generic timer interrupt was not triggered unless autosleep was
disabled. Since autosleep is enabled in the newer chipsets,
enable generic timer for using with bt coex logic.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Move bt_stomp to ath9k_hw and add its support for latest chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add API that allows low level drivers to notify mac80211 about TX
packet loss. This is useful when there are FW triggers to notify the
low level driver about these events.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch "cfg80211: add a timer for invalid user reg hints"
introduced a regression for the case where a secondary identical
regulatory hint from a user is sent. What would happen is the
second hint would schedule delayed work in to catch a timeout
but since we are never processing it given that the hint was already
applied we'd always hit the timeout and and restore regulatory
settings back to world regulatory domain. This is fixed by simply
avoiding sheduling work if the hint was already applied.
Tested-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix most sparse warnings in rtlwifi, rtl8192ce and rtl8192cu drivers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192ce: Change rtl8192ce routines phy and trx and modify rtl8192cu for addition of rtl8192se and rtl8192de

Change rtl8192ce routines phy and trx for addition of RTL8192SE and RTL8192DE.
In addition, make necessary modifications to rtl8192cu. This patch also
removes the temporary patches needed to enable intermediate steps to build
without error.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change rtl8192ce routines phy and rc for addition of RTL8192SE and
RTL8192DE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change rtl8192ce sw and LED routines for addition of RTL8192SE and
RTL8192DE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change rtl8192ce hw routine for addition of RTL8192SE and RTL8192DE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change common PHY routines for addition of RTL8192SE and RTL8192DE code.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change common firmware routines for addition of RTL8192SE and
RTL8192DE code.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c-common: Convert common dynamic management routines for addition of rtl8192se and rtl8192de

Convert common dynamic management routines for addition of RTL8192SE
and RTL8192DE code.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Convert usb routines for addition of RTL8192SE and RTL8192DE code
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Convert regulatory domain  routines for addition of RTL8192SE and
RTL8192DE code.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Convert rc routines for addition of RTL8192SE and RTL8192DE code
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Convert ps routines for addition of RTL8192SE and RTL8192DE code
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Convert pci routines for addition of RTL8192SE and RTL8192DE code
These changes allow the upper-level driver to specify the BAR to be
used as it is different for rtl8192se than for the others.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Convert core routines for addition of RTL8192SE and RTL8192DE code.

Additional files are changed to allow compilation.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change cam routines for addition of RTL8192SE and RTL8192DE code
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change base routines for addition of RTL8192SE and RTL8192DE code.

Additional files are modified to allow compilation.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change wifi.h for addition of RTL8192SE and RTL8192DE code
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change efuse routines for addition of RTL8192SE and RTL8192DE code
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These warnings are exposed by gcc 4.6.
net/mac80211/sta_info.c: In function 'sta_info_cleanup_expire_buffered':
net/mac80211/sta_info.c:590:32: warning: variable 'sdata' set but not used
net/mac80211/ibss.c: In function 'ieee80211_rx_mgmt_auth_ibss':
net/mac80211/ibss.c:43:34: warning: variable 'status_code' set but not used
net/mac80211/work.c: In function 'ieee80211_send_assoc':
net/mac80211/work.c:203:9: warning: variable 'len' set but not used
net/mac80211/tx.c: In function '__ieee80211_parse_tx_radiotap':
net/mac80211/tx.c:1039:35: warning: variable 'sband' set but not used
net/mac80211/mesh.c: In function 'ieee80211_mesh_rx_queued_mgmt':
net/mac80211/mesh.c:616:28: warning: variable 'ifmsh' set but not used
 ...
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>