Change the powerpc hpte_insert routines now called through ppc_md to
static scope.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Apparently we've copied the todc drivers, for various RTCs used in
embedded machines from ARCH=ppc to ARCH=powerpc, despite the fact that
it's never used in the latter.  This patch removes it.

If we ever need these drivers (which we probably shouldn't now the RTC
class stuff is in), we can transfer them one by one from ARCH=ppc,
removing from the hideous abomination which is the todc
"infrastructure".
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Without this patch, on an idle system I get:

cpu-power-0:21.638
cpu-power-1:27.102
cpu-power-2:29.343
cpu-power-3:25.784
Total: 103.8W

With this patch:

cpu-power-0:11.730
cpu-power-1:17.185
cpu-power-2:18.547
cpu-power-3:17.528
Total: 65.0W

If I lower HZ to 100, I can get it as low as:

cpu-power-0:10.938
cpu-power-1:16.021
cpu-power-2:17.245
cpu-power-3:16.145
Total: 60.2W

Another (older) Quad G5 went from 54W to 39W at HZ=250.

Coming back out of Deep Nap takes 40-70 cycles longer than coming back
from just Nap (which already takes quite a while). I don't think it'll
be a performance issue (interrupt latency on an idle system), but in
case someone does measurements feel free to report them.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This implements a lazy strategy for disabling interrupts.  This means
that local_irq_disable() et al. just clear the 'interrupts are
enabled' flag in the paca.  If an interrupt comes along, the interrupt
entry code notices that interrupts are supposed to be disabled, and
clears the EE bit in SRR1, clears the 'interrupts are hard-enabled'
flag in the paca, and returns.  This means that interrupts only
actually get disabled in the processor when an interrupt comes along.

When interrupts are enabled by local_irq_enable() et al., the code
sets the interrupts-enabled flag in the paca, and then checks whether
interrupts got hard-disabled.  If so, it also sets the EE bit in the
MSR to hard-enable the interrupts.

This has the potential to improve performance, and also makes it
easier to make a kernel that can boot on iSeries and on other 64-bit
machines, since this lazy-disable strategy is very similar to the
soft-disable strategy that iSeries already uses.

This version renames paca->proc_enabled to paca->soft_enabled, and
changes a couple of soft-disables in the kexec code to hard-disables,
which should fix the crash that Michael Ellerman saw.  This doesn't
yet use a reserved CR field for the soft_enabled and hard_enabled
flags.  This applies on top of Stephen Rothwell's patches to make it
possible to build a combined iSeries/other kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>

During boot we bring up all memory and cpu nodes. Normally a PCI device
will be in one of these online nodes, however in some weird setups it
may not.

We have only seen this in the lab but we may as well check for the case
and fallback to -1 (all nodes).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Instead of just checking that an address is in the right range, use the
provided __kernel_text_address() helper which covers both the kernel and
module text sections.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Change ->num_pmcs to match the number of PMCs in POWER6.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

At the moment we rely on a cpu feature bit or a firmware property to
detect altivec. If we dont have either of these and the cpu does in fact
support altivec we can cause a panic from userspace.

It seems safer to always send a signal if we manage to get an 0xf20
exception from userspace.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

When update_bridge_base() updates the IO window on a PCI-to-PCI
bridge, it fails to zero the upper 16 bits of the base and limit
registers if the window size is less than 64K.  This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>

Add missing entry in Makefile for MPC832x MDS support.  It
also change white space to tab in MPC8360 entry.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

MPC8360EMDS PB support is broken as some code was missing
in last submission.  This patch adds missing code and makes
MPC8360EMDS PB support working.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

In the timer_interrupt we were not calling set_irq_regs() and if we are
profiling we will end up calling get_irq_regs().  This causes bad things to
happen.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

A find -iname \*.[ch] | xargs grep "> ARRAY_SIZE(" revealed several
incorrect usages of ARRAY_SIZE in the mpc drivers.  The last element in the
array is always ARRAY_SIZE()-1, this patch modifies the bounds checks
accordingly.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The default configuration file for the MPC8349E-mITX reference board,
mpc834x_itx_defconfig, did not include support for DOS partition table types.
This support is necessary because the hard drive that comes with the ITX
is formatted with this partition table type.  Without this config option,
no partitions on the drive can be mounted.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This fixes a memory leak introduced by "spufs: add support
for read/write oncntl", which was missing a call to simple_attr_close.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The SPU code will crash if CONFIG_NUMA is not set and SPUs are found on
a non-0 node. This workaround will ignore those SPEs and just print an
message in the kernel log.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

I need this patch to get a UML kernel to compile.  This is with the
kernel headers in FC6 which are automatically generated from the kernel
tree.  Some headers are missing but those files don't need them.  At
least it appears so since the resuling kernel works fine.

Tested on x86-64.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

.. and clean up the file mapping code while at it.  No point in having a
"if (file)" repeated twice, and generally doing similar checks in two
different sections of the same code
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

It is silly to use non-static variable for writting zeroes to the file.

And more seriously, foffset in core dump file dump function was incremented
too much, so some parts of core dump were shifted by size of few phdrs and
notes down, so although gdb was able to load that file, it did not make lot
of sense - in my test case data pages were shifted down by about 900 bytes.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (28 commits)
  ACPI: check battery status on resume for un/plug events during sleep
  ACPICA: Fix incorrect handling of PCI Express Root Bridge _HID
  ACPI: asus_acpi: don't printk on writing garbage to proc files
  ACPI: asus_acpi: fix proc files parsing
  ACPI: SCI interrupt source override
  ACPI: fix printk format warnings
  ACPI: fix section for CPU init functions
  ACPI: update comments in motherboard.c
  ACPI: acpi_pci_link_set() can allocate with either GFP_ATOMIC or GFP_KERNEL
  ACPI: fix potential OOPS in power driver with CONFIG_ACPI_DEBUG
  ACPI: ibm_acpi: delete obsolete documentation
  ACPI: created a dedicated workqueue for notify() execution
  ACPI: Remove deferred execution from global lock acquire wakeup path
  MSI S270 Laptop support: backlight, wlan, bluetooth states
  ACPI: EC: export ec_transaction() for msi-laptop driver
  ACPI: EC: Simplify acpi_hw_low_level*() with inb()/outb().
  ACPI: EC: Unify poll and interrupt gpe handlers
  ACPI: EC: Unify poll and interrupt mode transaction functions
  ACPI: EC: Remove unused variables and duplicated code
  ACPI: EC: Remove unnecessary delay added by previous transation patch.
  ...

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (4750): AGC command1/2 is board specific
  V4L/DVB (4748): Fixed oops for Nova-T USB2
  V4L/DVB (4746): HM12 is YUV 4:2:0, not YUV 4:1:1
  V4L/DVB (4744): The Samsung TCPN2121P30A does not have a tda9887
  V4L/DVB (4743): Fix oops in VIDIOC_G_PARM
  V4L/DVB (4742): Drivers/media/video: handle sysfs errors
  V4L/DVB (4741): {ov511,stv680}: handle sysfs errors
  V4L/DVB (4740): Fixed an if-block to avoid floating with debug-messages
  V4L/DVB (4739): SECAM support for saa7113 into saa7115
  V4L/DVB (4738): Bt8xx/dvb-bt8xx.c: check kmalloc() return value.
  V4L/DVB (4734): Tda826x: fix frontend selection for dvb_attach
  V4L/DVB (4733): Tda10086: fix frontend selection for dvb_attach
  V4L/DVB (4732): Fix spelling error in Kconfig help text for DVB_CORE_ATTACH
  V4L/DVB (4731a): Kconfig: restore pvrusb2 menu items
  V4L/DVB (4729): Fix VIDIOC_G_FMT for NTSC in cx25840.
  V4L/DVB (4727): Support status readout for saa713x based FM radio
  V4L/DVB (4725): Fix vivi compile on parisc
  V4L/DVB (4692): Add WinTV-HVR3000 DVB-T support

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* missing cpu_to_le64() for ChangeTime (introduced by
    [CIFS] Legacy time handling for Win9x and OS/2 part 1)
* missing le16_to_cpu() for DialectIndex (introduced by
    [CIFS] Do not send newer QFSInfo to legacy servers which can not support it)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Add ->resume method to the ACPI battery handler to check
if the battery state has changed during sleep.
If yes, update the ACPI internal data structures
for benefit of /proc/acpi/battery/.
Signed-off-by: Jiri Kosina <jikos@jikos.cz>
Cc: Stefan Seyfried <seife@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>

I could not get correct PCI Express bus number from the structure of
acpi_object_extra. I always get zero as bus number regardless of bus
location. I found that there is incorrect comparison with _HID (PNP0A08) in
acpi/events/evrgnini.c and PCI Express _BBN method always fail.
Therefore, we always get zero as PCI Express bus number.
http://bugzilla.kernel.org/show_bug.cgi?id=7145Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

This reporting is useless (we errno anyway).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>

ICC complains about a "Pointless comparsion of unsigned interger with zero"
@ line 760 & 808 of asus_acpi.c

parse_arg() mentioned below returns -E but it's copied into unsigned variable...
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>

The Linux group at Stratus Technologies has come across an issue with SCI
routing under ACPI.  We were bitten by this when we made an x86_64 platform
whose BIOS provides an Interrupt Source Override for the SCI itself.
Apparently the override has no effect for the System Control Interrupt, and
this appears to be because of the way the SCI is setup in the ACPI code.
It does not handle the case where busirq != gsi.

The code that sets up the SCI routing assumes that bus irq == global irq.
So there is simply no provision for telling it otherwise.  The attached
patch provides this mechanism.

This patch provided by David Bulkow, was tested on an i386 platform, which
does not use the SCI override, and also on an x86_64 platform which does
use an override.
Signed-off-by: David Bulkow <david.bulkow@stratus.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>