Marvell CP110 COMPHY block is fed by 3 clocks. Describe each of them in the
bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Now that all COMPHY modes are supported by the driver, update the
comment stating that mvebu_comphy_power_off() should be called for
each lane. This is still wrong because for compatibility reasons, it
might break users running an old firmware (the driver only uses SMC
calls for SATA, USB and PCIe configuration, there is no code in Linux
to fallback on in these cases.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add PCIe support by filling the COMPHY modes table.

Also add a new macro to generate the right value for the firmware
depending on the width (PCI x1, x2, x4, etc). The width will be passed
by the core as the "submode" argument of the ->set_mode() callback. If
this argument is zero, default to x1 mode.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Before adding more logic, simplify a bit the writing of the
mvebu_comphy_get_mode() helper by using a pointer instead of
referencing a configuration with the entire table name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add the corresponding entries in the COMPHY modes table.

SATA support does not need any additional care.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add USB3 host/device support by adding the right entries in the COMPHY
modes table. A new macro is created to instantiate a "generic" mode
ie. not an Ethernet one. This macro will be re-used when adding SATA
support.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The COMPHY can configure the SERDES lanes in several non-Ethernet
modes: SATA, USB3, PCIe. Drop the condition limiting the driver to
Ethernet modes only before adding support for more.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Before adding support for other PHY modes (not Ethernet ones), let's
rename the MVEBU_COMPHY_CONF macro to a more specific (and shorter)
appellation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add support for RXAUI mode by adding an entry in the COMPHY modes list.

There is no user for this mode yet so we can enforce an up-to-date
firmware and return an error otherwise without breaking anywone.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Currently, the driver supports setting lanes to 1000BASEX, 2500BASEX,
10GKR. Complete the COMPHY modes list by adding two (already
supported) cases for lane 4.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Keep the exact same list of supported configurations but first try to
use the firmware's implementation. If it fails, try the legacy method:
Linux implementation.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Explicitly set the lane submode (enum) to a known invalid value.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

There is no public clock tree that implies such dependencies between
the MG/MG-core/AXI clocks and the COMPHY IP but accessing the COMPHY
registers while one of the three clocks are disabled stalls the CPU.

This happens if, for instance, the COMPHY driver probe is deferred
(eg. the USB Vbus regulator driver is not yet visible). The MVPP2
driver which also needs these clocks (among others) will
prepare/enable the clocks, then be deferred, and disable/unprepare
them. Next COMPHY lane to be configured would produce an infinite
stall.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

After commit "linux/bits.h: Add compile time sanity check of GENMASK
inputs" [1], arm64 defconfig builds started failing:

In file included from ../include/linux/bits.h:22,
                 from ../include/linux/bitops.h:5,
                 from ../include/linux/kernel.h:12,
                 from ../include/linux/clk.h:13,
                 from ../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:9:
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c: In function 'inno_hdmi_phy_rk3328_power_on':
../include/linux/build_bug.h:16:45: error: negative width in bit-field '<anonymous>'
   16 | #define BUILD_BUG_ON_ZERO(e) (sizeof(struct { int:(-!!(e)); }))
      |                                             ^
../include/linux/bits.h:24:18: note: in expansion of macro 'BUILD_BUG_ON_ZERO'
   24 |  ((unsigned long)BUILD_BUG_ON_ZERO(__builtin_choose_expr( \
      |                  ^~~~~~~~~~~~~~~~~
../include/linux/bits.h:39:3: note: in expansion of macro 'GENMASK_INPUT_CHECK'
   39 |  (GENMASK_INPUT_CHECK(high, low) + __GENMASK(high, low))
      |   ^~~~~~~~~~~~~~~~~~~
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:24:42: note: in expansion of macro 'GENMASK'
   24 | #define UPDATE(x, h, l)  (((x) << (l)) & GENMASK((h), (l)))
      |                                          ^~~~~~~
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:201:50: note: in expansion of macro 'UPDATE'
  201 | #define RK3328_TERM_RESISTOR_CALIB_SPEED_7_0(x)  UPDATE(x, 7, 9)
      |                                                  ^~~~~~
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:1046:26: note: in expansion of macro 'RK3328_TERM_RESISTOR_CALIB_SPEED_7_0'
 1046 |   inno_write(inno, 0xc6, RK3328_TERM_RESISTOR_CALIB_SPEED_7_0(v));
      |                          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

As pointed out by Robin and Guenter, inno_write's val argument is an
8-bit value so having a mask larger than that doesn't make sense. This
also matches the rest of the *_7_0 macros in this driver.

[1]: https://lore.kernel.org/lkml/20190801230358.4193-2-rikard.falkeborn@gmail.com/Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: kernelci.org bot <bot@kernelci.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>

Despite extensive testing of commit 885bd765 ("phy: qcom-qmp: Correct
READY_STATUS poll break condition") I failed to conclude that the
PHYSTATUS bit of the PCS_STATUS register used in PCIe and USB3 falls as
the PHY gets ready. Similar to the prior bug with UFS the code will
generally get past the check before the transition and thereby
"succeed".

Correct the name of the register used PCIe and USB3 PHYs, replace
mask_pcs_ready with a constant expression depending on the type of the
PHY and check for the appropriate ready state.

Cc: stable@vger.kernel.org
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Fixes: 885bd765 ("phy: qcom-qmp: Correct READY_STATUS poll break condition")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence create a new label,
err_node_put, that puts the previous node (child) before returning the
required value. Also include the statement pm_runtime_disable() under
this label in order to avoid repetition among mid-loop return
conditions. Edit the mid-loop return statements to instead go to this
new label err_node_put.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The hardware manual should be revised, but the initial value of
VBCTRL.OCCLREN is set to 1 actually. If the bit is set, the hardware
clears VBCTRL.VBOUT and ADPCTRL.DRVVBUS registers automatically
when the hardware detects over-current signal from a USB power switch.
However, since the hardware doesn't have any registers which
indicates over-current, the driver cannot handle it at all. So, if
"is_otg_channel" hardware detects over-current, since ADPCTRL.DRVVBUS
register is cleared automatically, the channel cannot be used after
that.

To resolve this behavior, this patch sets the VBCTRL.OCCLREN to 0
to keep ADPCTRL.DRVVBUS even if the "is_otg_channel" hardware
detects over-current. (We assume a USB power switch itself protects
over-current and turns the VBUS off.)

This patch is inspired by a BSP patch from Kazuya Mizuguchi.

Fixes: 1114e2d3 ("phy: rcar-gen3-usb2: change the mode to OTG on the combined channel")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The regmap_node variable is still being used in the syscon_node_to_regmap()
call after the of_node_put() call, which may result in use-after-free.

Fixes: 71e2f5c5 ("phy: ti: Add a new SERDES driver for TI's AM654x SoC")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

PHY configuration has been implemented in the firmware and accessed
through SMC calls. In the past, it worked magically if the bootloader
was correctly doing the initializations.

With up-to-date bindings, the kernel will need a recent firmware in
order to do the initializations himself (we assume people must update
their firmware along with their kernel).

People might not understand why IPs that were working correctly before
stopped to be probed suddendly. In this case, let's advise the users
to update their firmware with a visual warning.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Samsung PHY drivers control the power to the SoC core components needed by
their client devices (USB HCDs, SATA, camera ISP bridge, DP encoder) to
properly operate. Disabling PHYs in runtime usually causes the client
device to crash with external abort exception or similar issue due to lack
of API to notify clients about PHY removal. This patch removes the
possiblity to unbind Samsung Exynos PHY drivers in runtime.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Commit 36914111 ("drivers: phy: add calibrate method") added support
for generic phy_calibrate() method, but it didn't explain in detail when
such method is supposed to be called. Add some more documentation directly
to the phy.h to make it clean that it is intended to be called after every
host controller reset.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return in two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return in two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Unconditionally include the lantiq subdirectory in the phy Makefile.

All drivers in there have their dependencies maintained. One of these
(optional) dependencies is COMPILE_TEST, however this can only be
evaluated when Kconfig scans the lantiq subdirectory.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The Lantiq VRX200 SoCs embed a PCIe PHY in the "sram" bus. Unlike most
other IP blocks on this SoC the register values are only 16-bit wide.
Like other IP blocks on this SoC the register values are in big endian.

The PHY embeds a PLL which can be configured in various modes. Only the
36MHz mode is supported for now, the other modes can be implemented when
there's a board which actually needs them. OpenWrt uses the out-of-tree
vendor driver and all supported boards there only need the 36MHz mode.

There are two input clocks:
- the "pdi" clock enables the register access
- the "phy" clock is the clock input and enables the internal PLL

There are two reset lines:
- "phy" resets the PHY itself
- the "pcie" reset line is shared between the PHY and the PCIe
  controller

While the VRX200 SoC has only one PCIe controller and PHY the ARX300
uses two identical PCIe controllers and PHYs which are compatible with
the PCIe controller and PHY on VRX200.
Add a driver for this PHY so PCIe support can be enabled on these SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add the bindings for the PCIe PHY on Lantiq VRX200 and ARX300 SoCs.
The IP block contains settings for the PHY and a PLL.
The PLL mode is configurable through a dedicated #phy-cell in .dts.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Pull structleak fix from Kees Cook:
 "Disable gcc-based stack variable auto-init under KASAN (Arnd
  Bergmann).

  This fixes a bunch of build warnings under KASAN and the
  gcc-plugin-based stack auto-initialization features (which are
  arguably redundant, so better to let KASAN control this)"

* tag 'meminit-v5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  structleak: disable STRUCTLEAK_BYREF in combination with KASAN_STACK

Merge tag 'kbuild-fixes-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - add compile_commands.json to .gitignore

 - fix false-positive warning from gen_compile_commands.py after
   allnoconfig build

 - remove unused code

* tag 'kbuild-fixes-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: remove unused single-used-m
  gen_compile_commands: lower the entry count threshold
  .gitignore: Add compilation database file
  kbuild: remove unused objectify macro

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for 5.3-rc2 to resolve
  some reported issues.

  Nothing major at all, some binder bugfixes for issues found, some new
  mei device ids, firmware building warning fixes, habanalabs fixes, a
  few other build fixes, and a MAINTAINERS update.

  All of these have been in linux-next with no reported issues"

* tag 'char-misc-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  test_firmware: fix a memory leak bug
  hpet: Fix division by zero in hpet_time_div()
  eeprom: make older eeprom drivers select NVMEM_SYSFS
  vmw_balloon: Remove Julien from the maintainers list
  fpga-manager: altera-ps-spi: Fix build error
  mei: me: add mule creek canyon (EHL) device ids
  binder: prevent transactions to context manager from its own process.
  binder: Set end of SG buffer area properly.
  firmware: Fix missing inline
  firmware: fix build errors in paged buffer handling code
  habanalabs: don't reset device when getting VRHOT
  habanalabs: use %pad for printing a dma_addr_t

Pull tty fixes from Greg KH:
 "Here are two tty/vt fixes:

   - delete the netx-serial driver as the arch has been removed, no need
     to keep the serial driver for it around either.

   - vt console_lock fix to resolve a reported noisy warning at runtime

  Both of these have been in linux-next with no reported issues"

* tag 'tty-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  vt: Grab console_lock around con_is_bound in show_bind
  tty: serial: netx: Delete driver

Pull SPDX fixes from Greg KH:
 "Here are some small SPDX fixes for 5.3-rc2 for things that came in
  during the 5.3-rc1 merge window that we previously missed.

  Only three small patches here:

   - two uapi patches to resolve some SPDX tags that were not correct

   - fix an invalid SPDX tag in the iomap Makefile file

  All have been properly reviewed on the public mailing lists"

* tag 'spdx-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
  iomap: fix Invalid License ID
  treewide: remove SPDX "WITH Linux-syscall-note" from kernel-space headers again
  treewide: add "WITH Linux-syscall-note" to SPDX tag of uapi headers

Pull USB fixes from Greg KH:
 "Here are some small fixes for 5.3-rc2. All of these resolve some
  reported issues, some more than others :)

  Included in here is:

   - xhci fix for an annoying issue with odd devices

   - reversion of some usb251xb patches that should not have been merged

   - usb pci quirk additions and fixups

   - usb storage fix

   - usb host controller error test fix

  All of these have been in linux-next with no reported issues"

* tag 'usb-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  xhci: Fix crash if scatter gather is used with Immediate Data Transfer (IDT).
  usb: usb251xb: Reallow swap-dx-lanes to apply to the upstream port
  Revert "usb: usb251xb: Add US port lanes inversion property"
  Revert "usb: usb251xb: Add US lanes inversion dts-bindings"
  usb: wusbcore: fix unbalanced get/put cluster_id
  usb/hcd: Fix a NULL vs IS_ERR() bug in usb_hcd_setup_local_mem()
  usb-storage: Add a limitation for blk_queue_max_hw_sectors()
  usb: pci-quirks: Minor cleanup for AMD PLL quirk
  usb: pci-quirks: Correct AMD PLL quirk detection

Pull ARM SoC fixes from Olof Johansson:
 "Here's the first batch of fixes for this release cycle.

  Main diffstat here is the re-deletion of netx. I messed up and most
  likely didn't remove the files from the index when I test-merged this
  and saw conflicts, and from there on out 'git rerere' remembered the
  mistake and I missed checking it. Here it's done again as expected.

  Besides that:

   - A defconfig refresh + enabling of new drivers for u8500

   - i.MX fixlets for i2c/SAI/pinmux

   - sleep.S build fix for Davinci

   - Broadcom devicetree build/warning fix"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: defconfig: u8500: Add new drivers
  ARM: defconfig: u8500: Refresh defconfig
  ARM: dts: bcm: bcm47094: add missing #cells for mdio-bus-mux
  ARM: davinci: fix sleep.S build error on ARMv4
  arm64: dts: imx8mq: fix SAI compatible
  arm64: dts: imx8mm: Correct SAI3 RXC/TXFS pin's mux option #1
  ARM: dts: imx6ul: fix clock frequency property name of I2C buses
  ARM: Delete netx a second time
  ARM: dts: imx7ulp: Fix usb-phy unit address format

Pull x86 fixes from Thomas Gleixner:
 "A set of x86 fixes and functional updates:

   - Prevent stale huge I/O TLB mappings on 32bit. A long standing bug
     which got exposed by KPTI support for 32bit

   - Prevent bogus access_ok() warnings in arch_stack_walk_user()

   - Add display quirks for Lenovo devices which have height and width
     swapped

   - Add the missing CR2 fixup for 32 bit async pagefaults. Fallout of
     the CR2 bug fix series.

   - Unbreak handling of force enabled HPET by moving the 'is HPET
     counting' check back to the original place.

   - A more accurate check for running on a hypervisor platform in the
     MDS mitigation code. Not perfect, but more accurate than the
     previous one.

   - Update a stale and confusing comment vs. IRQ stacks"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/speculation/mds: Apply more accurate check on hypervisor platform
  x86/hpet: Undo the early counter is counting check
  x86/entry/32: Pass cr2 to do_async_page_fault()
  x86/irq/64: Update stale comment
  x86/sysfb_efi: Add quirks for some devices with swapped width and height
  x86/stacktrace: Prevent access_ok() warnings in arch_stack_walk_user()
  mm/vmalloc: Sync unmappings in __purge_vmap_area_lazy()
  x86/mm: Sync also unmappings in vmalloc_sync_all()
  x86/mm: Check for pfn instead of page in vmalloc_sync_one()

Pull scheduler fixes from Thomas Gleixner:
 "Two fixes for the fair scheduling class:

   - Prevent freeing memory which is accessible by concurrent readers

   - Make the RCU annotations for numa groups consistent"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Use RCU accessors consistently for ->numa_group
  sched/fair: Don't free p->numa_faults with concurrent readers

Pull perf fixes from Thomas Gleixner:
 "A pile of perf related fixes:

  Kernel:
   - Fix SLOTS PEBS event constraints for Icelake CPUs

   - Add the missing mask bit to allow counting hardware generated
     prefetches on L3 for Icelake CPUs

   - Make the test for hypervisor platforms more accurate (as far as
     possible)

   - Handle PMUs correctly which override event->cpu

   - Yet another missing fallthrough annotation

  Tools:
     perf.data:
        - Fix loading of compressed data split across adjacent records
        - Fix buffer size setting for processing CPU topology perf.data
          header.

     perf stat:
        - Fix segfault for event group in repeat mode
        - Always separate "stalled cycles per insn" line, it was being
          appended to the "instructions" line.

     perf script:
        - Fix --max-blocks man page description.
        - Improve man page description of metrics.
        - Fix off by one in brstackinsn IPC computation.

     perf probe:
        - Avoid calling freeing routine multiple times for same pointer.

     perf build:
        - Do not use -Wshadow on gcc < 4.8, avoiding too strict warnings
          treated as errors, breaking the build"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Mark expected switch fall-throughs
  perf/core: Fix creating kernel counters for PMUs that override event->cpu
  perf/x86: Apply more accurate check on hypervisor platform
  perf/x86/intel: Fix invalid Bit 13 for Icelake MSR_OFFCORE_RSP_x register
  perf/x86/intel: Fix SLOTS PEBS event constraint
  perf build: Do not use -Wshadow on gcc < 4.8
  perf probe: Avoid calling freeing routine multiple times for same pointer
  perf probe: Set pev->nargs to zero after freeing pev->args entries
  perf session: Fix loading of compressed data split across adjacent records
  perf stat: Always separate stalled cycles per insn
  perf stat: Fix segfault for event group in repeat mode
  perf tools: Fix proper buffer size for feature processing
  perf script: Fix off by one in brstackinsn IPC computation
  perf script: Improve man page description of metrics
  perf script: Fix --max-blocks man page description

Pull locking fixes from Thomas Gleixner:
 "A set of locking fixes:

   - Address the fallout of the rwsem rework. Missing ACQUIREs and a
     sanity check to prevent a use-after-free

   - Add missing checks for unitialized mutexes when mutex debugging is
     enabled.

   - Remove the bogus code in the generic SMP variant of
     arch_futex_atomic_op_inuser()

   - Fixup the #ifdeffery in lockdep to prevent compile warnings"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/mutex: Test for initialized mutex
  locking/lockdep: Clean up #ifdef checks
  locking/lockdep: Hide unused 'class' variable
  locking/rwsem: Add ACQUIRE comments
  tty/ldsem, locking/rwsem: Add missing ACQUIRE to read_failed sleep loop
  lcoking/rwsem: Add missing ACQUIRE to read_slowpath sleep loop
  locking/rwsem: Add missing ACQUIRE to read_slowpath exit when queue is empty
  locking/rwsem: Don't call owner_on_cpu() on read-owner
  futex: Cleanup generic SMP variant of arch_futex_atomic_op_inuser()

Pull objtool fix from Thomas Gleixner:
 "A single robustness fix for objtool to handle unbalanced CLAC
  invocations under all circumstances"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Improve UACCESS coverage