- 27 Apr, 2007 40 commits
-
-
Hartmut Hackmann authored
The struct tda1004x_config has a new entry: .ts_mode Possible values are TDA10046_TS_PARALLEL or TDA10046_TS_SERIAL There always is only one interface active, default is parallel. Signed-off-by:
Hartmut Hackmann <hartmut.hackmann@t-online.de> Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@infradead.org>
-
Trent Piepho authored
The dvb-pll sleep function could only send a 2-byte sequence to the PLL. This isn't enough in some cases, for example fmd1216me will need to send a 4-byte command to set both BB and AB to the correct values. Instead of using a fake band with a frequency of 0 to store the sleep data (which has room for only two bytes), the new sleep function works like the init function. A new pointer is added to the pll description, and when non-NULL points to a buffer with the length and data to send. Signed-off-by:
Trent Piepho <xyzzy@speakeasy.org> Signed-off-by:
-
Trent Piepho authored
The IF frequency was specified for each band, but it's not something that changes from band to band. None of the tuner definitions had a different IF frequency (called offset) from one band to another. Acked-by:
-
Trent Piepho authored
Some PLLs had one half the step size added to the offset, so that the divisor would be rounded to the nearest integer. Some didn't and so would always be rounded down. This makes dvb-pll round to the nearest when calculating the divisor, without the offset needing to be fudged. PLLs that had a fudged offset have the offset changed to be just the IF frequency. The satellite PLL dvb_pll_philips_sd1878_tda8261 was rounding up for some reason, and I've kept it that way. In addition, frequencies that were rounded to the nearest kHz are extended to full Hz resolution. One sixth MHz step sizes that were listed as 166,666 Hz are changed to 166,667 Hz, which is slightly closer. PLLs that were already rounding: dvb_pll_tda665x, offset was 36 1/6 (to nearest kHz) + step/2 dvb_pll_fmd1216me, offset was 36 1/8 (to two digits) + step/2 dvb_pll_thomson_fe6600, offset was 36 1/8 (to two digits) + step/2 dvb_pll_env57h1xd5, offset was 36 1/8 + step Note that the last PLL, dvb_pll_env57h1xd5, appears to have had a bug in the offset. Rather than adding stepsize/2, it was adding a full stepsize. The PLL definition originally came from the dibusb driver, which used 36 1/8 + step/2. The change to 36 1/8 + step was probably a mistake added when the tuner was converted to dvb-pll. Signed-off-by:
-
Trent Piepho authored
The attach code for HAUPPAUGE_HVR3000 and HAUPPAUGE_HVR1300 is exactly the same as the code used by HAUPPAUGE_HVR1100, HAUPPAUGE_HVR1100LP, and WINFAST_DTV2000H. So, those first two cards are added to the case block used by the last three. Signed-off-by:
-
Pierre Willenbrock authored
Signed-off-by:
Pierre Willenbrock <pierre@pirsoft.dnsalias.org> Signed-off-by:
Aapo Tahkola <aet@rasterburn.org> Signed-off-by:
-
Aapo Tahkola authored
This function should work for all m920x-based devices. Signed-off-by:
-
Hartmut Hackmann authored
The new name fits to what it is and what is on the box. Signed-off-by:
-
Hartmut Hackmann authored
There are 2 new entries for p7131 boards and one correction for a board with LNA. Signed-off-by:
-
Hartmut Hackmann authored
Static locals should not be changed - the original contents gets lost. Thanks to Trent Piepho for pointing me to this. Signed-off-by:
-
Hartmut Hackmann authored
Besides power saving, this puts the AGC output of the tda8290 to tristate. This is necessary for some hybrid boards which don't use a multiplexer for the AGC Signed-off-by:
-
Oliver Endriss authored
Fix bug introduced during infrared refactoring. Thanks to Johann Friedrichs for spotting this. Thanks-to: Johann Friedrichs <johann.friedrichs@web.de> Signed-off-by:
Oliver Endriss <o.endriss@gmx.de> Signed-off-by:
-
Ian Armstrong authored
Modifies automatic mode selection for yuv playback. Behaviour is now that source video with a vertical resolution below that of the currently set broadcast mode will be treated as progressive. Video with a vertical resolution greater or equal to the current broadcast mode (up to 576 lines) will be treated as interlaced. Signed-off-by:
Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Ian Armstrong authored
Adds more osd mode switching information. Corrects some information regarding mode selection & local alpha operation for 16 bit modes. Signed-off-by:
-
Hans Verkuil authored
The TV standard should be set AFTER the TV output is fully initialized. Signed-off-by:
-
Steven Toth authored
Some of the new tuner entries may need to be mapped to compatible tuners already defined. I don't know for certain which tuners are compatible between manufacturers. Signed-off-by:
Steven Toth <stoth@hauppauge.com> Signed-off-by:
-
Michael Krufky authored
replace leading spaces with tabs Signed-off-by:
-
Michael Krufky authored
The ADS Tech InstantTV DVB-S is a clone of the KWorld DVB-S 100. This patch adds autodetection support for this card based on pci subsystem id. Signed-off-by:
-
Trent Piepho authored
Change a 00 to just 0 Detect zero-length I2C messages and return not supported. I think I know how to send one, but the problem is getting the slave's ack. The only point of a zero-length message is for probing; too see if the slave will ack its address. Since we don't know how to get the ack, we can't support zero-length messages in a useful way, so it's probably best to just return not supported for them. Signed-off-by:
-
Trent Piepho authored
Write some better documentation about what might be known about how the m920x I2C works, since a datasheet is lacking. The I2C xfer function should now handle more types of I2C transactions than it could before. Those it can't, will return error codes instead of being executed incorrectly. Multi-byte reads were not being done correctly, which should be fixed. Signed-off-by:
-
Aapo Tahkola authored
Signed-off-by:
-
Aapo Tahkola authored
Signed-off-by:
-
Aapo Tahkola authored
- r/w bit is not part of the i2c address Signed-off-by:
-
Aapo Tahkola authored
- Implement m920x i2c as suggested by Pierre Willenbrock - remove "magic" hack - r/w bit is not part of the i2c address - move hardware remarks to header file Signed-off-by:
-
Hans Verkuil authored
Once the devices have been registered anyone can start changing the inputs or TV standard before they have been initialized by the driver. This leads to cases were the input is changed in an udev rule, but after that rule is triggered the tail-end of the ivtv driver initialization can override that by selecting the tuner input. The correct sequence is to first setup the input, initial frequency and TV standard before finally registering the video devices. This prevents any udev rules from being triggered prematurely. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Negative speed values have to be allowed for reverse playback. Signed-off-by:
-
Hans Verkuil authored
ivtv_remove which is called by pci_unregister_driver was still using memory that was already freed. Ouch. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
VIDIOC_TRY_ENCODER_CMD did the same as VIDIOC_ENCODER_CMD, now it no longer touches the encoder. Both the encoder and decoder commands did not clear the flags field of unknown flags. Signed-off-by:
-
Hans Verkuil authored
Using v4l_printk_ioctl saves a lot of code duplication. Also moved a few ioctl cases to another function, improving the ioctl grouping. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Those two experimental APIs never worked fine nor, afaik, were implemented at the apps. Their functionalities were implemented by other means. So, let's remove those obsolete stuff. Signed-off-by:
-
Hans Verkuil authored
It is not immediately obvious why the ivtv symbols are exported in ivtv-driver.c since both ivtv-fb and the IR-blaster module are still out-of-tree, currently being ported to be in kernel. Added a comment so people are aware of these issues. Signed-off-by:
-
Hans Verkuil authored
Every file should include the headers containing the prototypes for its global functions. Signed-off-by:
Adrian Bunk <bunk@stusta.de> Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
