- 04 Jul, 2014 24 commits
-
-
Marcel Holtmann authored
This adds support for configuring the hci_vhci virtual controllers to require a setup stage using HCI_QUIRK_EXTERNAL_CONFIG. With this option the virtual controller will start out as unconfigured. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
For the quirks that are allow to be set during setup callback, the check needs to be modified so that they are applied even if no setup callback provided by the driver. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
When a controller requires external configuration, then setting this quirk will allow indicating this. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
Reading the controller configuration information is a valid management command when the controller is unconfigured. Allow this command, but return invalid index on all other commands. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
When the Broadcom USB controller has a default address, then set the quirk so the Bluetooth core knows that controller configuration is required. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
When the Intel USB controller has a default address, then set the quirk so the Bluetooth core knows that controller configuration is required. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
When a Bluetooth controller does not have a valid public Bluetooth address, then allow the driver to indicate this. If the quirk is set, the Bluetooth core will switch to unconfigured state first and will allow userspace to configure the address before starting the full initialization of the controller. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
The current existing device quirks are not documented. So instead of spreading bits and pieces somewhere in the code, add proper comments on where these quirks can be used and what behavior they change. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Johan Hedberg authored
It's wasteful to use list_del_init (which re-initializes the list_head) if we're just about to free the element and never use it again. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
If a found device is marked as blocked while doing passive LE scanning, neither report it nor try to connect to it. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Marcel Holtmann authored
The public address configuration option is value 0x02 since the generic external configuration is value 0x01. So adjust this accordingly and also add the value 0x01 to the list. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Johan Hedberg authored
Instead of looking through the entire list of entries we can more efficiently use the new hci_pend_le_action_lookup() function to look up entries specifically in the pend_le_reports list. Since the search is now limited to the right list we can also remove an unnecessary check for list_empty() before the lookup. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
In some circumstances we need to look up entries in pend_le_conns and in other in pend_le_reports. This patch converts the existing lookup function for pend_le_conns to something that can be used for both lists. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Since there are no more users of this function we can simply go ahead and remove it. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
This is the last place using hci_pend_le_conn_add() and we can more just as simply manipulate the list directly here. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
When powering off (hci_dev_do_close) we should clear both the pend_le_reports and pend_le_conns types of entries. When powering on respectively we should populate both lists. This patch converts the hci_pend_le_conns_clear() function into hci_pend_le_actions_clear() (which can now be static) and converts the restart_le_auto_conns() function into restart_le_actions(). Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Now that there are no-longer any users of the hci_pend_le_conn_del() function we can simply go ahead and remove it. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Since params->action is used for both the pend_le_conns and pend_le_reports lists we can simplify the adding and deleting of the lists considerably. For example, when deleting entries in most situations we no-longer need to check the auto_connect value but can directly proceed with calling list_del_init on param->action (which is safe even if the entry is not part of any list). Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
When hci_conn_params_set() is called if the new auto_connect value is the same as the old one we don't need to take any action. Simply return success from the function in this case. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Now that pend_le_connections is a list of hci_conn_params entries we can simply remove items from that list as we iterate through the global list of le_conn_params. This also moves the responsibility of calling hci_update_background_scan() to the functions that were previously calling hci_pend_le_conns_clear(). The only user that's left for hci_pend_le_conns_clear() is hci_dev_do_close() which anyway does not need to call hci_update_background_scan(). Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
To simplify manipulation and lookup of hci_conn_params entries of the type HCI_AUTO_CONN_REPORT it makes sense to store them in their own list. The new action list_head in hci_conn_params is used for this purpose. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
In preparation to store also HCI_AUTO_CONN_REPORT entries in a list it makes sense to convert the existing pend_le_conn list head of hci_conn_params into a more generically named "action". This makes sense because a parameter entry will never participate in more than one action list. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
If we're doing passive scanning we shouldn't proceed with any of the code that deals with active scanning (pending reports, etc.). This patch fixes a missing return statement for the passive scanning section in the process_adv_report() function. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Marcel Holtmann authored
The Read Controller Configuration Information command allows retrieving details about possible configurations option. The supported options are returned and also the missing options (if any). Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
- 03 Jul, 2014 16 commits
-
-
Johan Hedberg authored
Since we only store entries with identity addresses in the le_conn_params and pend_le_conns lists we can avoid unnecessary lookups by checking for an identity address before diving into the lists themselves. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
If a device is in the pend_le_conns list it cannot at the same time also have the need to be notified through mgmt_device_found. By making check_pending_le_conn return whether it found an entry or not we can avoid unnecessary checks in process_adv_report(). Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Since the connection parameters are always a basis for adding entries to hdev->pend_le_conns (so far of type bdaddr_list) it's simpler and more efficient to have the parameters themselves be the entries in the pend_le_conns list. We do this by adding another list_head to the hci_conn_params struct. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
When processing passive scanning results we need the resolved identity address both in check_pending_le_conn() as well as later in process_adv_report(). Since process_adv_report() calls check_pending_le_conn() we can simply resolve the IRK earlier in the function and thereby eliminate a second lookup. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
When calling Remove Device for an entry using HCI_AUTO_CONN_REPORT we need to decrement the pend_le_reports value correspondingly. This patch fixes one such missing action in the Remove Device command handler. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
The handler for variable length commands were trying to calculate the expected length of the command based on the given parameter count, and then comparing that with the received data. However, the expected count was stored in a u16 which can easily overflow. With a carefully crafted command this can then be made to match the given data even though the parameter count is actually way too big, resulting in a buffer overflow when parsing the parameters. This patch fixes the issue by calculating a per-command maximum parameter count and returns INVALID_PARAMS if it is exceeded. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
When we're scanning for specific devices that use an RPA we need to convert the RPA to the identity address before looking up the entry in the connection parameters. This patch adds the necessary code to do this in the process_adv_report() function. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
If we have one or more devices with HCI_AUTO_CONN_REPORT we should do background scanning and emit mgmt_device_found events. This patch modifies the hci_update_background_scan() function to extend the conditions needed to trigger scanning, and adds the necessary code to process_adv_report() to emit mgmt_device_found events. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
When the kernel is doing LE scanning because of one or more devices added with action 0x00 through the Add Device command we do want to let mgmt_device_found() to proceed with sending an event. This kind of devices are tracked with hdev->pend_le_reports, so check this value before bailing out from the function. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
To be able to make the right choice of whether to start passive scanning or to send out a mgmt_device_found event we need to know if there are any devices in the le_conn_params list with the auto_connect value set to HCI_AUTO_CONN_REPORT. This patch adds a counter for this kind of devices. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Marcel Holtmann authored
This adds support for configuring the hci_vhci virtual controllers as a raw-only device using HCI_QUIRK_RAW_DEVICE. This is useful for testing the kernel internal infrastructure. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
This command allows to get the list of currently known controller that are in unconfigured state. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
When a controller in an unconfigured state gets removed, then send Unconfigured Index Removed events. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
When a controller is in unconfigured state it is currently hidden from the management interface. This change now announces the new controller with an Unconfigured Index Added event and allows clients to easily detect the controller. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
With the new unconfigured controller state it is possible to provide a fully functional HCI transport, but disable the higher level operations that would normally happen. This way userspace can try to configure the controller before releases the unconfigured state. The internal state is represented by HCI_UNCONFIGURED. This replaces the HCI_QUIRK_RAW_DEVICE quirk as internal state representation. This is now a real state and drivers can use the quirk to actually trigger this state. In the future this will allow a more fine grained switching from unconfigured state to configured state for controller inititialization. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Johan Hedberg authored
If we don't have an identity address for connection parameters it doesn't really make sense to send them to user space. Instead just ignore them for now. Later we can add support for sending them when we eventually get the identity through pairing. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-