- 12 Oct, 2016 14 commits
-
-
Karol Herbst authored
Now the cstatei parameter can be used of the nvkm_cstate_prog function to select a specific cstate. v5: Make a constant for the magic value. Use list_last_entry. Add nvkm_cstate_get here instead of in the next commit. Signed-off-by:Karol Herbst <karolherbst@gmail.com> Signed-off-by:
Ben Skeggs <bskeggs@redhat.com>
-
Karol Herbst authored
The voltage entries actually may map to a different voltage depending on the current temperature. v2: Only read the temperature when actually needed. v5: Be smarter about using max(). Don't read the temperature anymore. Signed-off-by:Martin Peres <martin.peres@free.fr> Signed-off-by:
-
Karol Herbst authored
This way other subdevs can notify the clk subdev about temperature changes without the need of clk to poll that value. Also make this function safe to be called from an interrupt handler. Signed-off-by:
-
Karol Herbst authored
It is better to read out the id out of the cstate struct directly instead of iterating over the list of cstates over and over again. Especially when we start saving pointers to a nvkm_cstate struct, it makes things easier. v5: Rename field to id. Signed-off-by:
-
Karol Herbst authored
Each pstate has its own voltage map entry like each cstate has. The voltages of those entries act as a floor value for the currently selected pstate and nvidia never sets a voltage below them. Signed-off-by:
-
Karol Herbst authored
There are at least three "max" entries, which specify the max voltage. Because they are actually normal voltage map entries, they can also be affected by the temperature. Nvidia respects those entries and if they get changed, nvidia uses the lower voltage from all three. We shouldn't exceed those voltages at any given time. v2: State what those entries do in the source. v3: Add the third max entry. v5: Better describe the entries. Signed-off-by:
-
Karol Herbst authored
nvkm_volt_map_min is a copy of nvkm_volt_map, which always returns the lowest possible voltage for a cstate. nvkm_volt_map will get a temperature parameter there later and also fix the voltage calculation, so that this functions will be completly different later. Signed-off-by:
Pierre Moreau <pierre.morrow@free.fr> Signed-off-by:
-
Karol Herbst authored
There is a field in the voltage table which tells us if the VIDs are taken from the entries or calculated through the header. v2: Don't break older versions. v5: Reverse flag name. Signed-off-by:
-
Karol Herbst authored
Some Fermi+ GPUs specify VID information via voltage table entries, rather than describing them as a range in the header. The mask may be bigger than 0x1fffff, but this value is already >2V, so it will be fine for now. This patch fixes volting issues on those cards enabling them to switch cstates. v6: rework message Signed-off-by:
-
Karol Herbst authored
Signed-off-by:
Aidan Epstein <aidan@jmad.org> Signed-off-by:
-
Karol Herbst authored
Signed-off-by:
-
Karol Herbst authored
Previously we parsed that table a bit wrong: 1. The entry layout depends on the sensor type used. 2. We have all resitors in one entry for the INA3221. 3. The config is already included in the vbios. This commit addresses that issue and with that we should be able to read out the right power consumption for every GPU with a INA209, INA219 and INA3221. Signed-off-by:
-
Ilia Mirkin authored
This can show up on SPARC or other architectures that don't handle unaligned accesses. The kernel normally fixes these up, but it shouldn't have to. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96836Signed-off-by:
Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by:
-
Alexandre Courbot authored
gk20a_ibus_init_ibus_ring() can be called from gk20a_ibus_intr(), in non-interruptible context. Replace use of usleep_range() with udelay(). Reported-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
Alexandre Courbot <acourbot@nvidia.com> Signed-off-by:
-
- 11 Oct, 2016 2 commits
-
-
git://anongit.freedesktop.org/drm-intelDave Airlie authored
Just flushing out my -misc queue. Slightly important are the prime refcount/unload fixes from Chris. There's also the reservation stuff from Chris still pending, and Sumits hasn't landed that yet. Might get another pull for that, but pls don't hold up the main pull for it ;-) * tag 'topic/drm-misc-2016-10-11' of git://anongit.freedesktop.org/drm-intel: drm/crtc: constify drm_crtc_index parameter drm: use the right function name in documentation drm: Release resources with a safer function drm: Fix up kerneldoc for new drm_gem_dmabuf_export() drm/bridge: Drop drm_connector_unregister and call drm_connector_cleanup directly drm/fb-helper: fix sphinx markup for DRM_FB_HELPER_DEFAULT_OPS drm/bridge: Add RGB to VGA bridge support drm/prime: Take a ref on the drm_dev when exporting a dma_buf drm/prime: Pass the right module owner through to dma_buf_export() drm/bridge: Call drm_connector_cleanup directly drm: simple_kms_helper: Add prepare_fb and cleanup_fb hooks drm: Release resources with a safer function
-
Dave Airlie authored
Merge tag 'drm-intel-next-fixes-2016-10-11' of git://anongit.freedesktop.org/drm-intel into drm-next A big bunch of i915 fixes for drm-next / v4.9 merge window, with more than half of them also cc: stable. We also continue to have more Fixes: annotations for our fixes, which should help the backporters and archeologists. * tag 'drm-intel-next-fixes-2016-10-11' of git://anongit.freedesktop.org/drm-intel: (27 commits) drm/i915: Fix conflict resolution from backmerge of v4.8-rc8 to drm-next drm/i915/guc: Unwind GuC workqueue reservation if request construction fails drm/i915: Reset the breadcrumbs IRQ more carefully drm/i915: Force relocations via cpu if we run out of idle aperture drm/i915: Distinguish last emitted request from last submitted request drm/i915: Allow DP to work w/o EDID drm/i915: Move long hpd handling into the hotplug work drm/i915/execlists: Reinitialise context image after GPU hang drm/i915: Use correct index for backtracking HUNG semaphores drm/i915: Unalias obj->phys_handle and obj->userptr drm/i915: Just clear the mmiodebug before a register access drm/i915/gen9: only add the planes actually affected by ddb changes drm/i915: Allow PCH DPLL sharing regardless of DPLL_SDVO_HIGH_SPEED drm/i915/bxt: Fix HDMI DPLL configuration drm/i915/gen9: fix the watermark res_blocks value drm/i915/gen9: fix plane_blocks_per_line on watermarks calculations drm/i915/gen9: minimum scanlines for Y tile is not always 4 drm/i915/gen9: fix the WaWmMemoryReadLatency implementation drm/i915/kbl: KBL also needs to run the SAGV code drm/i915: introduce intel_has_sagv() ...
-
- 10 Oct, 2016 24 commits
-
-
Jani Nikula authored
Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1476113170-13816-1-git-send-email-jani.nikula@intel.com
-
Chris Wilson authored
The conflict resolution of v4.8-rc8 backmerge to drm-next pulled back in a few lines of dead code due to the code movement around i915_gem_reset(), fix that up. Fixes: ca09fb9f ("Merge tag 'v4.8-rc8' into drm-next") Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Dave Airlie <airlied@gmail.com> Signed-off-by:
-
Chris Wilson authored
We reserve space in the GuC workqueue for submitting the request in the future. However, if we fail to construct the request, we need to give that reserved space back to the system. Fixes: dadd481b ("drm/i915/guc: Prepare for nonblocking execbuf submission") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97978Signed-off-by:
Michał Winiarski <michal.winiarski@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20161007065327.24515-4-chris@chris-wilson.co.uk (cherry picked from commit 5ba89908) Signed-off-by:
-
Chris Wilson authored
Along with the interrupt, we want to restore the fake-irq and wait-timeout detection. If we use the breadcrumbs interface to setup the interrupt as it wants, the auxiliary timers will also be restored. v2: Cancel both timers as well, sanitize the IMR. Fixes: 821ed7df ("drm/i915: Update reset path to fix incomplete requests") Signed-off-by:
Mika Kuoppala <mika.kuoppala@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20161007065327.24515-3-chris@chris-wilson.co.uk (cherry picked from commit ad07dfcd) Signed-off-by:
-
Chris Wilson authored
If we run out of enough aperture space to fit the entire object, we fallback to trying to insert a single page. However, if that also fails, we currently fail to userspace with an unexpected ENOSPC. (ENOSPC means to userspace that their batch could not be fitted within the GTT.) Prior to commit e8cb909a ("drm/i915: Fallback to single page GTT mmappings for relocations") the approach is to fallback to using the slow CPU relocation path in case of iomapping failure, and that is the behaviour we need to restore. Fixes: e8cb909a ("drm/i915: Fallback to single page GTT mmappings...") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98101Signed-off-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20161007065327.24515-2-chris@chris-wilson.co.uk (cherry picked from commit d7f76335) Signed-off-by:
-
Chris Wilson authored
In order not to trigger hangcheck on a idle-but-waiting engine, we need to distinguish between the pending request queue and the actual execution queue. This is done later in "drm/i915: Enable multiple timelines" but for now we need a temporary fix to prevent blaming the wrong engine for a GPU hang. (Note that this causes a temporary subtle change in how we decide when to allow a waitboost to be re-awarded back to the waiter, the temporary effect is that if the wait is upon the most current execution the wait is given for free, instead of checking to see if the client stalled itself. This will be repaired in "drm/i915: Enable multiple timelines".) Fixes: 0a046a0e ("drm/i915: Nonblocking request submission") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98104Signed-off-by:
-
Ville Syrjälä authored
Allow returning "connected" or "unknown" connector status for DP branch devices that don't have an EDID. Currently we'd claim the thing as "disconnected" if there is no EDID. This stuff used to broken already, I think, but it got more broken by commit f21a2198 ("drm/i915: Splitting intel_dp_detect") Cc: Damien Cassou <damien@cassou.me> Cc: freedesktop.org@gp.mailgun.org Cc: Arno <blouin.arno@gmail.com> Cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com> Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com> Cc: stable@vger.kernel.org Tested-by:
Arno <blouin.arno@gmail.com> Fixes: f21a2198 ("drm/i915: Splitting intel_dp_detect") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83348Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1475481316-8194-2-git-send-email-ville.syrjala@linux.intel.comReviewed-by:
Ander Conselvan de Oliveira <conselvan2@gmail.com> (cherry picked from commit 5cb651a7) Signed-off-by:
-
Ville Syrjälä authored
We can't rely on connector->status in the detect() hook if the long hpd was already handled by the dig_port_work as that won't update connector->status. Thus we have to defer the long hpd handling entirely until the hotplug work runs to avoid the double long hpd handling the "detect_done" flag is trying to prevent. We'll start to depend on connector->status being up to date in a following patch. Cc: Damien Cassou <damien@cassou.me> Cc: freedesktop.org@gp.mailgun.org Cc: Arno <blouin.arno@gmail.com> Cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com> Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com> Cc: stable@vger.kernel.org Tested-by:
-
Chris Wilson authored
On Braswell, at least, we observe that the context image is written in multiple phases. The first phase is to clear the register state, and subsequently rewrite it. A GPU reset at the right moment can interrupt the context update leaving it corrupt, and our update of the RING_HEAD is not sufficient to restart the engine afterwards. To recover, we need to reset the registers back to their original values. The context state is lost. What we need is a better mechanism to serialise the reset with pending flushes from the GPU. Fixes: 821ed7df ("drm/i915: Update reset path to fix incomplete requests") Signed-off-by:
-
Chris Wilson authored
When decoding the semaphores inside hangcheck, we need to use the hw-id and not the local array index. Fixes: de1add36 ("drm/i915: Decouple execbuf uAPI ...") Testcase: igt/gem_exec_whisper/hang # gen6-7 Signed-off-by:
-
Chris Wilson authored
We use obj->phys_handle to choose the pread/pwrite path, but as obj->phys_handle is a union with obj->userptr, we then mistakenly use the phys_handle path for userptr objects within pread/pwrite. Testcase: igt/gem_userptr_blits/forbidden-operations Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97519Signed-off-by:
-
Chris Wilson authored
When we enable the per-register access mmiodebug, it is to detect which access is illegal. Reporting on earlier untraced access outside of the mmiodebug does not help debugging (as the suspicion is immediately put upon the current register which is not at fault)! References: https://bugs.freedesktop.org/show_bug.cgi?id=97985Signed-off-by:
-
Paulo Zanoni authored
We were previously adding all the planes owned by the CRTC even when the ddb partitioning didn't change for them. As a consequence, a lot of functions were being called when we were just moving the cursor around the screen, such as skylake_update_primary_plane(). This was causing flickering on the primary plane when moving the cursor. I'm not 100% sure which operation caused the flickering, but we were writing to a lot of registers, so it could be any of these writes. With this patch, just moving the mouse won't add the primary plane to the commit since it won't trigger a change in DDB partitioning. v2: Use skl_ddb_entry_equal() (Lyude). v3: Change Reported-and-bisected-by: to Reported-by: for checkpatch Fixes: 05a76d3d ("drm/i915/skl: Ensure pipes with changed wms get added to the state") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97888 Cc: Mike Lothian <mike@fireburn.co.uk> Cc: stable@vger.kernel.org Reported-by:
Mike Lothian <mike@fireburn.co.uk> Signed-off-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by:
Lyude <cpaul@redhat.com> Link: http://patchwork.freedesktop.org/patch/msgid/1475177808-29955-1-git-send-email-paulo.r.zanoni@intel.com (cherry picked from commit 7f60e200) Signed-off-by:
-
Ville Syrjälä authored
DPLL_SDVO_HIGH_SPEED must be set for SDVO/HDMI/DP, but nowhere is it forbidden to set it for LVDS/CRT as well. So let's also set it on CRT to make it possible to share the DPLL between HDMI and CRT. What that bit apparently does is enable the x5 clock to the port, which then pumps out the bits on both edges of the clock. The DAC doesn't need that clock since it's not pumping out bits, but I don't think it hurts to have the DPLL output that clock anyway. This is fairly important on IVB since it has only two DPLLs with three pipes. So trying to drive three or more PCH ports with three pipes is only possible when at least one of the DPLLs gets shared between two of the pipes. SNB doesn't really need to do this since it has only two pipes. It could be done to avoid enabling the second DPLL at all in certain cases, but I'm not sure that's such a huge win. So let's not do it for SNB, at least for now. On ILK it never makes sense as the DPLLs can't be shared. v2: Just always enable the high speed clock to keep things simple (Daniel) Beef up the commit message a bit (Daniel) Cc: Nick Yamane <nick.diego@gmail.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Tested-by:Nick Yamane <nick.diego@gmail.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97204Signed-off-by:
-
Imre Deak authored
a277ca7d should've been a no-functional-change commit, but it removed the initialization of the dpll_hw_state for HDMI outputs, resulting in state mismatches and a failed modeset with blank screen. Fix this by reinstating the dpll_hw_state initialization. v2: - Make bxt_ddi_hdmi_set_dpll_hw_state() static. Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Cc: Durgadoss R <durgadoss.r@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Fixes: a277ca7d ("drm/i915: Split bxt_ddi_pll_select()") Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
-
Paulo Zanoni authored
We forgot the "res_blocks += y_tile_minimum" that's described on step V of our documentation. Again, this should only affect the Y tiling cases. It looks like the relevant code was introduced in 0fda6568, but there's always the possibility that it matched our specification when it was introduced, and then the specification changed while the code stayed the same. So we can't really say this was a regression, but let's try to add a "Fixes" tag anyway to help backporting. v2: Try to add a "Fixes" tag (Maarten). Fixes: 0fda6568 ("drm/i915/skl: Update watermarks for Y tiling") Cc: stable@vger.kernel.org Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by:
-
Paulo Zanoni authored
The confusing thing is that plane_blocks_per_line is listed as part of the method 2 calculation but is also used for other things. We calculated it in two different places and different ways: one inside skl_wm_method2() and the other inside skl_compute_plane_wm(). The skl_wm_method2() implementation is the one that matches the specification. With this patch we fix the skl_compute_plane_wm() calculation and just pass it as a parameter to skl_wm_method2(). We also take care to not modify the value of plane_bytes_per_line since we're going to rely on it having a correct value in later patches. This should affect the watermarks for Linear and Y-tiled. From my analysis, it looks like the two plane_blocks_per_line variables got out of sync on 0fda6568, but we can't really say that commit was a regression, it looks like just an incomplete fix. There's always the possibility that 0fda6568 matched our specification at that time, and then later the specification changed. v2: Try to add a "Fixes" tag (Maarten). Fixes: 0fda6568 ("drm/i915/skl: Update watermarks for Y tiling") Cc: stable@vger.kernel.org Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by:
-
Paulo Zanoni authored
During watermarks calculations, this value is used in 3 different places. Only one of them was not using a hardcoded 4. Move the code up so everybody can benefit from the actual value. This should only help on situations with Y tiling + 90/270 rotation + 1 or 2 bpp or NV12. Cc: stable@vger.kernel.org Reviewed-by:
-
Paulo Zanoni authored
Bspec says: "The mailbox response data may not account for memory read latency. If the mailbox response data for level 0 is 0us, add 2 microseconds to the result for each valid level." This means we should only do the +2 in case wm[0] == 0, not always. So split the sanitizing implementation from the WA implementation and fix the WA implementation. v2: Add Fixes tag (Maarten). Fixes: 367294be ("drm/i915/gen9: Add 2us read latency to WM level") Cc: stable@vger.kernel.org Cc: Vandana Kannan <vandana.kannan@intel.com> Reviewed-by:
-
Paulo Zanoni authored
According to BSpec, it's the "core CPUs" that need the code, which means SKL and KBL, but not BXT. I don't have a KBL to test this patch on it. v2: Only SKL should have I915_SAGV_NOT_CONTROLLED. Cc: stable@vger.kernel.org Reviewed-by:
-
Paulo Zanoni authored
And use it to move knowledge about the SAGV-supporting platforms from the callers to the SAGV code. We'll add more platforms to intel_has_sagv(), so IMHO it makes more sense to move all this to a single function instead of patching all the callers every time we add SAGV support to a new platform. v2: Move I915_SAGV_NOT_CONTROLLED to the new function (Lyude). Cc: stable@vger.kernel.org Reviewed-by:
-
Paulo Zanoni authored
The plan is to introduce intel_has_sagv() and then use it to discover which platforms actually support it. I thought about keeping the functions with their current skl names, but found two problems: (i) skl_has_sagv() would become a very confusing name, and (ii) intel_atomic_commit_tail() doesn't seem to be calling any functions whose name start with a platform name, so the "intel_" naming scheme seems make more sense than the "firstplatorm_" naming scheme here. Cc: stable@vger.kernel.org Reviewed-by:
-
Paulo Zanoni authored
We never remembered to set it (so it was zero), but this was not a problem in the past due to the way handled the hardware registers. Unfortunately we changed how we set the hardware and forgot to set intel_crtc->dspaddr_offset. This started to reflect on a few kms_frontbuffer_tracking subtests that relied on page flips with CRTCs that don't point to the x:0,y:0 coordinates of the frontbuffer. After the page flip the CRTC was showing the x:0,y:0 coordinate of the frontbuffer instead of x:500,y:500. This problem is present even if we don't enable FBC or PSR. While trying to bisect it I realized that the first bad commit actually just gives me a black screen for the mentioned tests instead of showing the wrong x:0,y:0 offsets. A few commits later the black screen problem goes away and we get to the point where the code is today, but I'll consider the black screen as the first bad commit since it's the point where the IGT subtests start to fail. Fixes: 6687c906 ("drm/i915: Rewrite fb rotation GTT handling") Testcase: kms_frontbuffer_tracking/fbc-1p-primscrn-shrfb-pgflip-blt Testcase: kms_frontbuffer_tracking/fbc-1p-primscrn-shrfb-evflip-blt Testcase: kms_frontbuffer_tracking/fbc-1p-shrfb-fliptrack Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Cc: drm-intel-fixes@lists.freedesktop.org Signed-off-by:
-
Chris Wilson authored
At the point of creating the hibernation image, the runtime power manage core is disabled - and using the rpm functions triggers a warn. i915_gem_shrink_all() tries to unbind objects, which requires device access and so tries to how an rpm reference triggering a warning: [ 44.235420] ------------[ cut here ]------------ [ 44.235424] WARNING: CPU: 2 PID: 2199 at drivers/gpu/drm/i915/intel_runtime_pm.c:2688 intel_runtime_pm_get_if_in_use+0xe6/0xf0 [ 44.235426] WARN_ON_ONCE(ret < 0) [ 44.235445] Modules linked in: ctr ccm arc4 rt2800usb rt2x00usb rt2800lib rt2x00lib crc_ccitt mac80211 cmac cfg80211 btusb rfcomm bnep btrtl btbcm btintel bluetooth dcdbas x86_pkg_temp_thermal intel_powerclamp coretemp snd_hda_codec_realtek crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec_generic aesni_intel snd_hda_codec_hdmi aes_x86_64 lrw gf128mul snd_hda_intel glue_helper ablk_helper cryptd snd_hda_codec hid_multitouch joydev snd_hda_core binfmt_misc i2c_hid serio_raw snd_pcm acpi_pad snd_timer snd i2c_designware_platform 8250_dw nls_iso8859_1 i2c_designware_core lpc_ich mfd_core soundcore usbhid hid psmouse ahci libahci [ 44.235447] CPU: 2 PID: 2199 Comm: kworker/u8:8 Not tainted 4.8.0-rc5+ #130 [ 44.235447] Hardware name: Dell Inc. XPS 13 9343/0310JH, BIOS A07 11/11/2015 [ 44.235450] Workqueue: events_unbound async_run_entry_fn [ 44.235453] 0000000000000000 ffff8801b2f7fb98 ffffffff81306c2f ffff8801b2f7fbe8 [ 44.235454] 0000000000000000 ffff8801b2f7fbd8 ffffffff81056c01 00000a801f50ecc0 [ 44.235456] ffff88020ce50000 ffff88020ce59b60 ffffffff81a60b5c ffffffff81414840 [ 44.235456] Call Trace: [ 44.235459] [<ffffffff81306c2f>] dump_stack+0x4d/0x6e [ 44.235461] [<ffffffff81056c01>] __warn+0xd1/0xf0 [ 44.235464] [<ffffffff81414840>] ? i915_pm_suspend_late+0x30/0x30 [ 44.235465] [<ffffffff81056c6f>] warn_slowpath_fmt+0x4f/0x60 [ 44.235468] [<ffffffff814e73ce>] ? pm_runtime_get_if_in_use+0x6e/0xa0 [ 44.235469] [<ffffffff81433526>] intel_runtime_pm_get_if_in_use+0xe6/0xf0 [ 44.235471] [<ffffffff81458a26>] i915_gem_shrink+0x306/0x360 [ 44.235473] [<ffffffff81343fd4>] ? pci_platform_power_transition+0x24/0x90 [ 44.235475] [<ffffffff81414840>] ? i915_pm_suspend_late+0x30/0x30 [ 44.235476] [<ffffffff81458dfb>] i915_gem_shrink_all+0x1b/0x30 [ 44.235478] [<ffffffff814560b3>] i915_gem_freeze_late+0x33/0x90 [ 44.235479] [<ffffffff81414877>] i915_pm_freeze_late+0x37/0x40 [ 44.235481] [<ffffffff814e9b8e>] dpm_run_callback+0x4e/0x130 [ 44.235483] [<ffffffff814ea5db>] __device_suspend_late+0xdb/0x1f0 [ 44.235484] [<ffffffff814ea70f>] async_suspend_late+0x1f/0xa0 [ 44.235486] [<ffffffff81077557>] async_run_entry_fn+0x37/0x150 [ 44.235488] [<ffffffff8106f518>] process_one_work+0x148/0x3f0 [ 44.235490] [<ffffffff8106f8eb>] worker_thread+0x12b/0x490 [ 44.235491] [<ffffffff8106f7c0>] ? process_one_work+0x3f0/0x3f0 [ 44.235492] [<ffffffff81074d09>] kthread+0xc9/0xe0 [ 44.235495] [<ffffffff816e257f>] ret_from_fork+0x1f/0x40 [ 44.235496] [<ffffffff81074c40>] ? kthread_park+0x60/0x60 [ 44.235497] ---[ end trace e438706b97c7f132 ]--- Alternatively, to actually shrink everything we have to do so slightly earlier in the hibernation process. To keep lockdep silent, we need to take struct_mutex for the shrinker even though we know that we are the only user during the freeze. Fixes: 7aab2d53 ("drm/i915: Shrink objects prior to hibernation") Signed-off-by:
-
