- 06 Dec, 2010 5 commits
-
-
Dimitris Papastamos authored
Added an optional name member to snd_soc_cache_ops to enable more sensible diagnostic messages during cache init, exit and sync. Remove redundant newline in source code. Signed-off-by:
Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Acked-by:
Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com>
-
Seungwhan Youn authored
This patch remove duplicated snd_card defination on smdk_spdif. Signed-off-by:
Seungwhan Youn <sw.youn@samsung.com> Acked-by:
Jassi Brar <jassi.brar@samsung.com> Acked-by:
-
Seungwhan Youn authored
This patch fixed intial return value to be a '0' as asuccess on set_audio_clock_heirachy(). This avoids unintended error on initialize. Signed-off-by:
-
Mark Brown authored
As jack detection can trigger DAPM and the latency in debouncing can create confusing windows in operation provide some trace events which will hopefully help in diagnostics. The soc-jack core traces all reports that it gets and the resulting notifications to upper layers. An event for jack IRQs is also provided for instrumentation of debounce, and used in the GPIO jack code. Signed-off-by:
-
Mark Brown authored
Currently the machine driver can only do bias level configuration before the CODEC bias level is brought up. This means that the machine cannot do any configuration which depends on the CODEC bias level being maintained. Provide a post-CODEC callback which allows the machine driver to do things like enable the FLL on a CODEC which is brought down to BIAS_OFF when idle. Signed-off-by:
-
- 03 Dec, 2010 19 commits
-
-
Mark Brown authored
-
Mark Brown authored
When we disable the WM8994 FLL code path sharing means that we end up writing out a configuration. Currently this is the currently active input and output frequency (which causes snd_soc_update_bits() to suppress actual writes both immediately and in the common case where we reenable the same configuration later) but we allow machine drivers to pass through a source of zero. Since the register values written are one less than the source constants this causes corruption of other bitfields in the register. Fix this by using the most recently configured FLL source when none is provided. Signed-off-by:
-
Jassi Brar authored
We want the index of DAI's driver here. Signed-off-by:
-
Mark Brown authored
Allow the CODEC driver structure to be marked const by making all the APIs that use it do so. Signed-off-by:
-
Dimitris Papastamos authored
This patch allows machine drivers to override the compression type provided by the codec driver. Signed-off-by:
-
Dimitris Papastamos authored
Make sure to use codec->reg_def_copy instead of codec_drv->reg_cache_default wherever necessary. This change is necessary because in the next patch we move the cache initialization code outside snd_soc_register_codec() and by that time any data marked as __devinitconst such as the original reg_cache_default array might have already been freed by the kernel. Signed-off-by:
-
Dimitris Papastamos authored
The snd_soc_codec_conf struct now holds codec specific configuration information. A new configuration option has been added to allow machine drivers to override the compression type set by the codec driver. In the absence of providing an snd_soc_codec_conf struct or when providing one but not setting the compress_type member to anything, the one supplied by the codec driver will be used instead. In all other cases the one set in the snd_soc_codec_conf struct takes effect. Signed-off-by:
Jarkko Nikula <jhnikula@gmail.com> Acked-by:
-
Dimitris Papastamos authored
Ensure that the base value of compress_type starts at 1 so that we know whether the machine driver has provided a compress_type for overriding the codec supplied one. Signed-off-by:
-
Dimitris Papastamos authored
We need to keep a copy of the compress_type supplied by the codec driver so that we can override it if necessary with whatever the machine driver has provided us with. The reason for not modifying the codec->driver struct directly is that ideally we'd like to keep it const. Adjust the code in soc-cache and soc-core to make use of the compress_type member in the snd_soc_codec struct. Signed-off-by:
-
Jarkko Nikula authored
Blind copy of codec finding algorithm from soc_bind_dai_link does not work in soc_probe_aux_dev if matching codec name is not found. In that case the code falls through and tries to start the probing procedure with invalid codec pointer. Fix this and add an error print showing the codec name that cannot be found. Signed-off-by:
-
Axel Lin authored
In alc5623_i2c_probe(), the default case for checking alc5623->id behaves the same as case 0x23. However, In alc5623_probe() the default case for checking alc5623->id becomes to be the same as case 0x21. This makes the meaning of default case inconsistent. Since we have checked codec id in alc5623_i2c_probe() by comparing vid2 with id->driver_data, it is not possible to run into the default case now. In case we may add more supported devices to alc5623_i2c_table in the future, this patch changes the default case return -EINVAL to let people know that they should not run into this case. They should also add a new case accordingly for the new id. Signed-off-by:
Axel Lin <axel.lin@gmail.com> Acked-by:
Arnaud Patard <arnaud.patard@rtp-net.org> Acked-by:
-
Kuninori Morimoto authored
Current FSI driver was checking register range on fsi_master_xxx function. This runtime check was added to avoid an illegal access from wrong/mistake implementation. But it is useless check under the correct implementation. This patch escape runtime check by using macro technique. If there is wrong implementation, it will be compile error. Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by:
-
Kuninori Morimoto authored
Current FSI driver was checking register range on fsi_reg_xxx function. This runtime check was added to avoid an illegal access from wrong/mistake implementation. But it is useless check under the correct implementation. This patch escape runtime check by using macro technique. If there is wrong implementation, it will be compile error. Signed-off-by:
-
Kuninori Morimoto authored
There was a strange part where fsi->xxx had been used for fsi_master_xxx function instead of master->xxx in current FSI. This patch modify it. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Mark Brown authored
We shouldn't be assigning to the driver structure (which really ought to be const, further patch to follow) though there's unlikely to be any actual problem except in the unlikely case that two devices with the same driver but different bus types appear in the same system. Signed-off-by:
-
Mark Brown authored
Neither drivers nor the core should be fiddling with the actual ops structure at runtime. Signed-off-by:
-
Mark Brown authored
Silly little grammar nit but it bugs the hell out of me. Signed-off-by:
-
- 02 Dec, 2010 6 commits
-
-
Takashi Iwai authored
Merge branch 'for-2.6.37' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc-2.6 into fix/asoc
-
Mark Brown authored
Update some of the default configuration for the device to improve the performance. Signed-off-by:
-
Mark Brown authored
The deemphasis filter should be selected based on sample rate for optimal performance. Signed-off-by:
-
Mark Brown authored
This is much more maintainable than the array. Signed-off-by:
-
Mark Brown authored
Signed-off-by:
-
Jarkko Nikula authored
Not all omap boards use kernel based pin multiplexing so CONFIG_SND_OMAP_SOC_N810 should not select it by default as it can make harm to other boards in multi-board kernels. Therefore put CONFIG_OMAP_MUX as a dependency to N810 ASoC machine driver. Thanks to Tony Lindgren <tony@atomide.com> for noticing. Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
- 01 Dec, 2010 8 commits
-
-
Axel Lin authored
The mute/unmute is controled by SMUTE (Soft Mute Control bit): 0: Normal Operation (Default) 1: DAC outputs soft-muted I think this change improves readability. Signed-off-by: -
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Mark Brown authored
The paramters of the WM8958 multiband compressor can be tuned by the user for their system using a graphical configuration tool on the host. Allow the user to specify a set of such paramters in platform data and select between them at runtime. Signed-off-by:
-
Mark Brown authored
We need a post notification as we need to shut down the MBC after the data stops flowing rather than before. Signed-off-by:
-
Mark Brown authored
-
Jarkko Nikula authored
Commit 2eea392d "ASoC: Add support for optional auxiliary dailess codecs" causes a build failure in soc-core.c: soc_probe_aux_dev since code tries to access non-existing struct snd_soc_dapm_context and struct snd_soc_card members. Root cause for this was a double accident. Author sent the RFC patch from top of another patch set and the RFC got committed. Fix the build failure by removing the code line that depends on that another patch set. Signed-off-by:
-
Dimitris Papastamos authored
According to the datasheet the bypass path enable/disable is bit 3 therefore we need 0x8 and not 0x4. Signed-off-by:
-
- 30 Nov, 2010 2 commits
-
-
Jarkko Nikula authored
This makes possible to register auxiliary dailess codecs in a machine driver. Term dailess is used here for amplifiers and codecs without DAI or DAI being unused. Dailess auxiliary codecs are kept in struct snd_soc_aux_dev and those codecs are probed after initializing the DAI links. There are no major differences between DAI link codecs and dailess codecs in ASoC core point of view. DAPM handles them equally and sysfs and debugfs directories for dailess codecs are similar except the pmdown_time node is not created. Only suspend and resume functions are modified to traverse all probed codecs instead of DAI link codecs. Example below shows a dailess codec registration. struct snd_soc_aux_dev foo_aux_dev[] = { { .name = "Amp", .codec_name = "codec.2", .init = foo_init2, }, }; static struct snd_soc_card card = { ... .aux_dev = foo_aux_dev, .num_aux_devs = ARRAY_SIZE(foo_aux_dev), }; Signed-off-by: -
Dimitris Papastamos authored
The bitmap_zero() nbits argument was improperly set to reg_size but the underlying buffer was bmp_size long. This caused the memset to zero past the end of the allocated buffer and into the kernel heap causing strange kernel crashes sometimes by overwriting critical kernel structures. Signed-off-by:
-
