- 16 Jan, 2014 1 commit
-
-
wangweidong authored
add sctp_spp_sackdelay_{enable|disable} helper function for avoiding code duplication. Signed-off-by:Wang Weidong <wangweidong1@huawei.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 15 Jan, 2014 39 commits
-
-
Li RongQing authored
Two places defined IPV6_TCLASS_SHIFT, so we should move it into ipv6.h, and use this macro as possible. And define ip6_tclass helper to return tclass Signed-off-by:
Li RongQing <roy.qing.li@gmail.com> Signed-off-by:
-
David S. Miller authored
Sathya Perla says: ==================== be2net: patch set The following patch set is best suited for net-next as it contains code-cleanup, support for newer versions of FW cmds and a few minor fixes. Please apply. Thanks! ==================== Signed-off-by: -
Sathya Perla authored
Signed-off-by:
Sathya Perla <sathya.perla@emulex.com> Signed-off-by:
-
Suresh Reddy authored
This patch cleans-up wake-on-lan code in the following ways: 1) Removes some driver hacks in be_cmd_get_acpi_wol_cap() that were based on incorrect assumptions. 2) Uses the adapter->wol_en and wol_cap variables for checking if WoL is supported and enabled on an interface instead of referring to the exclusion list via the macro be_is_wol_supported() Signed-off-by:
Suresh Reddy <suresh.reddy@emulex.com> Signed-off-by:
-
Suresh Reddy authored
The use of NTKW_MAC_QUERY cmd has been deprecated for Skyhawk-R. Replace the last remaining usage in be_vfs_mac_query() routine. Signed-off-by:
-
Suresh Reddy authored
Instead, use the tail of the RXQ to pick the associated RXQ entry This fix is required in preparation for supporting RXQ lengths greater than 1K. For such queues, the frag index in the RX-compl entry is not valid as it is only a 10 bit entry not capable of addressing RXQs longer than 1K. Signed-off-by:
-
Suresh Reddy authored
As be2net is used even by the 40Gbps Skyhawk-R chip Signed-off-by:
-
Suresh Reddy authored
An earlier commit (f25b119c "Fix error messages while driver load for VFs") incorrectly set the adapter->cmd_privileges value for VFs (in a multi-channel config) to MAX_PRIVILEGES. This causes FW cmd failures and avoidable error logs when certian cmds are issued by a VF. Also, move the multi-channel hack to be_cmds.c inside be_cmd_get_fn_privileges() routine. Fixes: f25b119c "Fix error messages while driver load for VFs" Signed-off-by:
-
Vasundhara Volam authored
An ndo_set_mac_addr() call may be issued for a mac-addr that is already active on an interface. If so, silently ignore the request. Sending such a request to the FW, causes a "mac collision" error. The error is harmless but is avoidable noise in the kernel log. Signed-off-by:
Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by:
-
Vasundhara Volam authored
Skyhawk-R FW does not support SET/GET_EXT_FAT_CAPABILITIES cmds via which FW logging level can be controlled. Also, the hack used in BE3 to control FW logging level via the ethtool interface is not needed in Skyhawk-R. This patch also cleans up this code by moving be_set/get_fw_log_level() routines to be_cmds.c where they belong. Signed-off-by:
-
Vasundhara Volam authored
Signed-off-by:
-
Vasundhara Volam authored
In the GET_HSW_CONFIG cmd, the "pport" field must be set only while querying the switch mode. When the "pport" field is set, the "interface_id" field must be set to the port number, otherwise, it must be set to adapter->if_handle. Signed-off-by:
-
Vasundhara Volam authored
Currently this cmd is used only for Lancer. MCC_CREATE_EXT_V1 supports larger CQ-ids and additional event codes for the async_event_bitmap field. Signed-off-by:
-
Joe Perches authored
Some systems can use the normally known u16 alignment of Ethernet addresses to save some code/text bytes and cycles. This does not change currently emitted code on x86 by gcc 4.8. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Dmitry Eremin-Solenikov authored
IEEE 802.15.4 and Bluetooth networking stacks share 6lowpan compression code. Instead of introducing Makefile/Kconfig hacks, build this code as a separate module referenced from both ieee802154 and bluetooth modules. This fixes the following build error observed in some kernel configurations: net/built-in.o: In function `header_create': 6lowpan.c:(.text+0x166149): undefined reference to `lowpan_header_compress' net/built-in.o: In function `bt_6lowpan_recv': (.text+0x166b3c): undefined reference to `lowpan_process_data' Reported-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
Dmitry Eremin-Solenikov <dmitry_eremin@mentor.com> Signed-off-by:
-
David S. Miller authored
Veaceslav Falico says: ==================== net: rename device's sysfs symlinks on name change First patch only adds helper functions and cleans up the code a bit, second one already does the renaming. v1->v2: Don't export the function, as it's used only in dev.c. ==================== Reported-by:
Ding Tianhong <dingtianhong@huawei.com> CC: Ding Tianhong <dingtianhong@huawei.com> CC: "David S. Miller" <davem@davemloft.net> CC: Eric Dumazet <edumazet@google.com> CC: Nicolas Dichtel <nicolas.dichtel@6wind.com> CC: Cong Wang <amwang@redhat.com> CC: netdev@vger.kernel.org Signed-off-by:
Veaceslav Falico <vfalico@redhat.com> Signed-off-by:
-
Veaceslav Falico authored
Currently, we don't rename the upper/lower_ifc symlinks in /sys/class/net/*/ , which might result stale/duplicate links/names. Fix this by adding netdev_adjacent_rename_links(dev, oldname) which renames all the upper/lower interface's links to dev from the upper/lower_oldname to the new name. We don't need a rollback because only we control these symlinks and if we fail to rename them - sysfs will anyway complain. Reported-by:
-
Veaceslav Falico authored
They clean up the code a bit and can be used further. CC: Ding Tianhong <dingtianhong@huawei.com> CC: "David S. Miller" <davem@davemloft.net> CC: Eric Dumazet <edumazet@google.com> CC: Nicolas Dichtel <nicolas.dichtel@6wind.com> CC: Cong Wang <amwang@redhat.com> Signed-off-by:
-
Vince Bridgers authored
GRO requires VLANs to be removed before aggregation can occur. The Synopsys EMAC does not strip VLAN tags so this must be done by the driver. Signed-off-by:
Vince Bridgers <vbridgers2013@gmail.com> Signed-off-by:
-
stephen hemminger authored
Fix new sparse warning about function declared static. Signed-off-by:
Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
-
Richard Weinberger authored
On archs like S390 or um this driver cannot build nor work. Make it depend on HAS_IOMEM to bypass build failures. drivers/built-in.o: In function `lpc32xx_adc_probe': drivers/staging/iio/adc/lpc32xx_adc.c:149: undefined reference to `devm_ioremap' Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
Richard Weinberger authored
On archs like S390 or um this driver cannot build nor work. Make it depend on HAS_IOMEM to bypass build failures. drivers/built-in.o: In function `goldfish_battery_probe': drivers/power/goldfish_battery.c:181: undefined reference to `devm_ioremap' Signed-off-by:
-
Richard Weinberger authored
On archs like S390 or um this driver cannot build nor work. Make it depend on HAS_IOMEM to bypass build failures. drivers/built-in.o: In function `orion_mdio_probe': drivers/net/ethernet/marvell/mvmdio.c:228: undefined reference to `devm_ioremap' Signed-off-by:
-
Richard Weinberger authored
On archs like S390 or um this driver cannot build nor work. Make it depend on HAS_IOMEM to bypass build failures. drivers/built-in.o: In function `exynos_mipi_video_phy_probe': drivers/phy/phy-exynos-mipi-video.c:130: undefined reference to `devm_ioremap_resource' Signed-off-by:
-
Richard Weinberger authored
On archs like S390 or um this driver cannot build nor work. Make it depend on HAS_IOMEM to bypass build failures. drivers/staging/iio/adc/spear_adc.c: In function ‘spear_adc_probe’: drivers/staging/iio/adc/spear_adc.c:393:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration Signed-off-by:
-
Richard Weinberger authored
On archs like S390 or um this driver cannot build nor work. Make it depend on HAS_IOMEM to bypass build failures. drivers/staging/dgap/dgap_driver.c: In function ‘dgap_cleanup_board’: drivers/staging/dgap/dgap_driver.c:457:3: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration] drivers/staging/dgap/dgap_driver.c: In function ‘dgap_do_remap’: drivers/staging/dgap/dgap_driver.c:694:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration] Signed-off-by:
-
Richard Weinberger authored
On archs like S390 or um this driver cannot build nor work. Make it depend on HAS_IOMEM to bypass build failures. drivers/ptp/ptp_pch.c: In function ‘pch_remove’: drivers/ptp/ptp_pch.c:571:3: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration] drivers/ptp/ptp_pch.c: In function ‘pch_probe’: drivers/ptp/ptp_pch.c:621:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration] Signed-off-by:
-
Eugene Crosser authored
Introduce functions to enable and disable bridgeport address notification feature, sysfs attributes for access to these functions from userspace, and udev events emitted when a host joins or exits a bridgeport-enabled HiperSocket channel. Signed-off-by:
Eugene Crosser <eugene.crosser@ru.ibm.com> Signed-off-by:
Frank Blaschka <frank.blaschka@de.ibm.com> Reviewed-by:
Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by:
-
Eugene Crosser authored
Introduce function for the "Perform network-subchannel operation" CHSC command with operation code "bridgeport information", and bit definitions for "characteristics" pertaning to this command. Signed-off-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by:
-
Eugene Crosser authored
Introduce functions to assign roles and check state of bridgeport-capable HiperSocket devices, and sysfs attributes providing access to these functions from userspace. Introduce udev events emitted when the state of a bridgeport device changes. Signed-off-by:
-
Jiri Pirko authored
introduced by: commit 1f9248e5 "neigh: convert parms to an array" Signed-off-by:
Jiri Pirko <jiri@resnulli.us> Signed-off-by:
-
Claudiu Manoil authored
Fixes unhandled register write in gianfar_ethtool.c. Fixes following endianess related functional issues, reported by sparse as well, i.e.: gianfar_ethtool.c:1058:33: warning: incorrect type in argument 1 (different base types) expected unsigned int [unsigned] [usertype] value got restricted __be32 [usertype] ip4src gianfar_ethtool.c:1164:33: warning: restricted __be16 degrades to integer gianfar_ethtool.c:1669:32: warning: invalid assignment: ^= left side has type restricted __be16 right side has type int Solves all the sparse warnings for mixig normal pointers with __iomem pointers for gianfar_ptp.c, i.e.: gianfar_ptp.c:163:32: warning: incorrect type in argument 1 (different address spaces) expected unsigned int [noderef] <asn:2>*addr got unsigned int *<noident> Signed-off-by:Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by:
-
Julia Lawall authored
Delete a variable that is at most only assigned to a constant, but never used otherwise. In this code, it is the variable result that is used for the return code, not rc. A simplified version of the semantic patch that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ type T; identifier i; constant c; @@ -T i; <... when != i -i = c; ...> // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
David S. Miller authored
Aaron Brown says: ==================== Intel Wired LAN Driver Updates This series contains updates to i40e from Greg Rose for VLAN filtering. Greg Rose (2): i40e: Warn admin to reload VF driver on port VLAN configuration. When an administrator sets a port VLAN filters for the virtual function (VF) after the VF has already set its own VLAN filters a conflict requiring the VF be reloaded can occur. This patch logs a message indicating to the system administrator that the VF driver must be reloaded for the new port VLAN settings to take effect i40e: Retain MAC filters on port VLAN deletion On port VLAN deletion the list of MAC filters for the virtual function (VF) VSI were all deleted. Let's keep them around, they come in handy for keeping the VF functional. ==================== Signed-off-by: -
Greg Rose authored
On port VLAN deletion the list of MAC filters for the virtual function (VF) VSI were all deleted. Let's keep them around, they come in handy for keeping the VF functional. Change-Id: I335e760392f274dc8b8b40efcb708f65b49d7973 Signed-off-by:
Greg Rose <gregory.v.rose@intel.com> Tested-by:
Sibai Li <sibai.li@intel.com> Signed-off-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
-
Greg Rose authored
The i40e Physical Function (PF) driver will allow the Virtual Function (VF) driver to configure its own VLAN filters if no port VLAN filter has been configured. This leads to the possibility of the administrator setting a port VLAN filter for the VF after the VF has already configured its own VLAN filters. This leads to a conflict that can only be resolved by reloading the VF driver. When the conflicting administrative command is detected in setting the port VLAN then log a message indicating to the system administrator that he must now reload the VF driver for the new port VLAN settings to take effect. Change-Id: I8de73b885d944a043aff32226297e4249862bcad Signed-off-by:
-
David S. Miller authored
Daniel Borkmann says: ==================== vxlan updates Did the split into two patches upon request from Cong Wang. Changelog: v1->v2: - Removed BUG_ON as it's not needed. v2->v3: - Removed dev->reg_state check for netns. v3->v4: - Removed list_del(), we seem to do it in some places and in some others not; we agreed it's not really necessary. - Split patch into 2 patches, notifier part and module unload cleanup part. ==================== Reviewed-by:Cong Wang <cwang@twopensource.com> Signed-off-by:
-
Daniel Borkmann authored
We should use vxlan_dellink() handler in vxlan_exit_net(), since i) we're not in fast-path and we should be consistent in dismantle just as we would remove a device through rtnl ops, and more importantly, ii) in case future code will kfree() memory in vxlan_dellink(), we would leak it right here unnoticed. Therefore, do not only half of the cleanup work, but make it properly. Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Signed-off-by:
-
Daniel Borkmann authored
We can create a vxlan device with an explicit underlying carrier. In that case, when the carrier link is being deleted from the system (e.g. due to module unload) we should also clean up all created vxlan devices on top of it since otherwise we're in an inconsistent state in vxlan device. In that case, the user needs to remove all such devices, while in case of other virtual devs that sit on top of physical ones, it is usually the case that these devices do unregister automatically as well and do not leave the burden on the user. This work is not necessary when vxlan device was not created with a real underlying device, as connections can resume in that case when driver is plugged again. But at least for the other cases, we should go ahead and do the cleanup on removal. We don't register the notifier during vxlan_newlink() here since I consider this event rather rare, and therefore we should not bloat vxlan's core structure unecessary. Also, we can simply make use of unregister_netdevice_many() to batch that. fdb is flushed upon ndo_stop(). E.g. `ip -d link show vxlan13` after carrier removal before this patch: 5: vxlan13: <BROADCAST,MULTICAST> mtu 1450 qdisc noop state DOWN mode DEFAULT group default link/ether 1e:47:da:6d:4d:99 brd ff:ff:ff:ff:ff:ff promiscuity 0 vxlan id 13 group 239.0.0.10 dev 2 port 32768 61000 ageing 300 ^^^^^ Signed-off-by:
-
