- 28 Jan, 2008 40 commits
-
-
Russell King authored
* pxa-plat: (53 commits) [ARM] 4762/1: Basic support for Toradex Colibri module [ARM] pxa: fix mci_init functions returning -1 [ARM] 4737/1: Refactor corgi_lcd to improve readability + bugfix [ARM] 4747/1: pcm027: support for pcm990 baseboard for phyCORE-PXA270 [ARM] 4746/1: pcm027: network support for phyCORE-PXA270 [ARM] 4745/1: pcm027: default configuration [ARM] 4744/1: pcm027: add support for phyCORE-PXA270 CPU module [NET] smc91x: Make smc91x use IRQ resource trigger flags [ARM] pxa: add default config for littleton [ARM] pxa: add basic support for Littleton (PXA3xx Form Factor Platform) [ARM] 4664/1: Add basic support for HTC Magician PDA phones [ARM] 4649/1: Base support for pxa-based Toshiba e-series PDAs. [ARM] pxa: skip registers saving/restoring if entering standby mode [ARM] pxa: fix PXA27x resume [ARM] pxa: Avoid fiddling with CKEN register on suspend [ARM] pxa: Add PXA3 standby code hooked into the IRQ wake scheme [ARM] pxa: Add zylonite MFP wakeup configurations [ARM] pxa: program MFPs for low power mode when suspending [ARM] pxa: make MFP configuration processor independent [ARM] pxa: remove un-used pxa3xx_mfp_set_xxx() functions ... Conflicts: arch/arm/mach-pxa/ssp.c Signed-off-by:Russell King <rmk+kernel@arm.linux.org.uk>
-
Russell King authored
* orion: (26 commits) [ARM] Orion: implement power-off method for QNAP TS-109/209 [ARM] Orion: add support for QNAP TS-109/TS-209 [ARM] Orion: I2C support [I2C] i2c-mv64xxx: Don't set i2c_adapter.retries [I2C] Split mv643xx I2C platform support [ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323 [ARM] Orion defconfig [ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323 [ARM] Orion: MV88F5181 support bits [ARM] Orion: Buffalo/Revogear Kurobox Pro support [ARM] OrionNAS RD board support [ARM] Orion: support for Marvell Orion-2 (88F5281) Development Board [ARM] Orion: common platform setup for Gigabit Ethernet port [ARM] Orion: platform device registration for UART, USB and NAND [ARM] Orion: system timer support [ARM] Orion edge GPIO IRQ support [ARM] Orion: IRQ support [ARM] Orion: provide GPIO method for enabling hardware assisted blinking [ARM] Orion: GPIO support [ARM] Orion: programable address map support ... Conflicts: arch/arm/Kconfig arch/arm/Makefile Signed-off-by: -
Russell King authored
Merge branches 'at91', 'ep93xx', 'iop', 'kprobes', 'ks8695', 'misc', 'msm', 's3c2410', 'sa1100' and 'vfp' into devel * at91: (24 commits) [ARM] 4615/4: sam926[13]ek buttons updated [ARM] 4765/1: [AT91] AT91CAP9A-DK board support [ARM] 4764/1: [AT91] AT91CAP9 core support [ARM] 4738/1: at91sam9261: Remove udc pullup enabling in board initialisation [ARM] 4761/1: [AT91] Board-support for NEW_LEDs [ARM] 4760/1: [AT91] SPI CS0 errata on AT91RM9200 [ARM] 4759/1: [AT91] Buttons on CSB300 [ARM] 4758/1: [AT91] LEDs [ARM] 4757/1: [AT91] UART initialization [ARM] 4756/1: [AT91] Makefile cleanup [ARM] 4755/1: [AT91] NAND update [ARM] 4754/1: [AT91] SSC library support [ARM] 4753/1: [AT91] Use DMA_BIT_MASK [ARM] 4752/1: [AT91] RTT, RTC and WDT peripherals on SAM9 [ARM] 4751/1: [AT91] ISI peripheral on SAM9263 [ARM] 4750/1: [AT91] STN LCD displays on SAM9261 [ARM] 4734/1: at91sam9263ek: include IRQ for Ethernet PHY [ARM] 4646/1: AT91: configurable HZ, default to 128 [ARM] 4688/1: at91: speed-up irq processing [ARM] 4657/1: AT91: Header definition update ... * ep93xx: [ARM] 4671/1: ep93xx: remove obsolete gpio_line_* operations [ARM] 4670/1: ep93xx: implement IRQT_BOTHEDGE gpio irq sense type [ARM] 4669/1: ep93xx: simplify GPIO code and cleanups [ARM] 4668/1: ep93xx: implement new GPIO API * iop: [ARM] 4770/1: GLAN Tank: correct physmap_flash_data width field [ARM] 4732/1: GLAN Tank: register rtc-rs5c372 i2c device [ARM] 4708/1: iop: update defconfigs for 2.6.24 * kprobes: ARM kprobes: let's enable it ARM kprobes: special hook for the kprobes breakpoint handler ARM kprobes: prevent some functions involved with kprobes from being probed ARM kprobes: don't let a single-stepped stmdb corrupt the exception stack ARM kprobes: add the kprobes hook to the page fault handler ARM kprobes: core code ARM kprobes: instruction single-stepping support * ks8695: [ARM] 4603/1: KS8695: debugfs interface to view pin state [ARM] 4601/1: KS8695: PCI support * misc: [ARM] remove duplicate includes [ARM] CONFIG_DEBUG_STACK_USAGE [ARM] 4689/1: small comment wrap fix [ARM] 4687/1: Trivial arch/arm/kernel/entry-common.S comment fix [ARM] 4666/1: ixp4xx: fix sparse warnings in include/asm-arm/arch-ixp4xx/io.h [ARM] remove reference to non-existent MTD_OBSOLETE_CHIPS [SERIAL] 21285: Report baud rate back via termios [ARM] Remove pointless casts from void pointers, [ARM] Misc minor interrupt handler cleanups [ARM] Remove at91_lcdc.h [ARM] ARRAY_SIZE() cleanup [ARM] Update mach-types * msm: [ARM] msm: dma support for MSM7X00A [ARM] msm: board file for MACH_HALIBUT (QCT MSM7200A) [ARM] msm: irq and timer support for ARCH_MSM7X00A [ARM] msm: core platform support for ARCH_MSM7X00A * s3c2410: (33 commits) [ARM] 4795/1: S3C244X: Add armclk and setparent call [ARM] 4794/1: S3C24XX: Comonise S3C2440 and S3C2442 clock code [ARM] 4793/1: S3C24XX: Add IRQ->GPIO pin mapping function [ARM] 4792/1: S3C24XX: Remove warnings from debug-macro.S [ARM] 4791/1: S3C2412: Make fclk a parent of msysclk [ARM] 4790/1: S3C2412: Fix parent selection for msysclk. [ARM] 4789/1: S3C2412: Add missing CLKDIVN register values [ARM] 4788/1: S3C24XX: Fix paramet to s3c2410_dma_ctrl if S3C2410_DMAF_AUTOSTART used. [ARM] 4787/1: S3C24XX: s3c2410_dma_request() should return the allocated channel number [ARM] 4786/1: S3C2412: Add SPI FIFO controll constants [ARM] 4785/1: S3C24XX: Add _SHIFT definitions for S3C2410_BANKCON registers [ARM] 4784/1: S3C24XX: Fix GPIO restore glitches [ARM] 4783/1: S3C24XX: Add s3c2410_gpio_getpull() [ARM] 4782/1: S3C24XX: Define FIQ_START for any FIQ users [ARM] 4781/1: S3C24XX: DMA suspend and resume support [ARM] 4780/1: S3C2412: Allow for seperate DMA channels for TX and RX [ARM] 4779/1: S3C2412: Add s3c2412_gpio_set_sleepcfg() call [ARM] 4778/1: S3C2412: Add armclk and init from DVS state [ARM] 4777/1: S3C24XX: Ensure clk_set_rate() checks the set_rate method for the clk [ARM] 4775/1: s3c2410: fix compilation error if only s3c2442 cpu is selected ... * sa1100: [ARM] sa1100: add clock source support * vfp: [ARM] 4584/2: ARMv7: Add Advanced SIMD (NEON) extension support [ARM] 4583/1: ARMv7: Add VFPv3 support [ARM] 4582/2: Add support for the common VFP subarchitecture
-
Ben Dooks authored
Add armclk to the supported clocks on the S3C2440 and S3C2442 to better represent the DVS state which controls whether FCLK or HCLK is fed to the ARM core. Signed-off-by:
Ben Dooks <ben-linux@fluff.org> Signed-off-by:
-
Ben Dooks authored
Merge together the bits of the S3C2440 and S3C2442 clock code that can be. Signed-off-by:
-
Ben Dooks authored
Add the reverse of s3c2410_gpio_getirq to convert a IRQ number into a GPIO pin number. Signed-off-by:
-
Ben Dooks authored
Remove warnings left in include/asm-arm/arch-s3c2410/debug-macro.S whilst these where being experimented with. Signed-off-by:
-
Ben Dooks authored
In the S3C2412 fclk is derived from msysclk, not straight from the MPLL output. Set clk_f.parent appropriately. Signed-off-by:
-
Ben Dooks authored
The msysclk clock was checking for the wrong PLL for the parent in s3c2412_setparent_msysclk(), trying the UPLL instead of the MPLL output. Also ensure the mpll and fclks are at the same rate at init time. Signed-off-by:
-
Ben Dooks authored
Add S3C2412_CLKDIVN_DVSEN and S3C2412_CLKDIVN_HALFHCLK definitions to the S3C2412_CLKDIVN set. Signed-off-by:
-
Ben Dooks authored
Fix the channel parameter to s3c2410_dma_ctrl() in s3c2410_dma_enqueue() if the S3C2410_DMAF_AUTOSTART is set on the channel. Spotted by Steven Ryu at Samsung. Signed-off-by:
-
Ben Dooks authored
The s3c2410_dma_request() function should return the channel allocated instead of zero for success. Signed-off-by:
-
Ben Dooks authored
Add control constants for the S3C2412 SPI unit FIFO. Signed-off-by:
-
Ben Dooks authored
Add definitions to allow easier decomposotion of the contents of the S3C2410_BANKON registers Signed-off-by:
-
Ben Dooks authored
The core resume code may have caused glitches in the GPIO when restoring the GPIO state due to the order in which the GPIO registers were being written. Change the restore process take into account the state of the GPIOs on resume and the state the system wants to restore them to. See the code comments in the patch for more details of the process. Signed-off-by:
-
Ben Dooks authored
Add the call s3c2410_gpio_getpull() to return the current state of the pin's pull-up. Signed-off-by:
-
Ben Dooks authored
Ensure FIQ_START is defined to allow anyone to use FIQ code on an S3C24XX based CPU. Signed-off-by:
-
Ben Dooks authored
If an DMA channel was active at suspend, then ensure that it is correctly reconfigured when the system resumes. Note, the previous policy was for each driver to handle their own reconfiguration on resume. The policy has been changed to make the individual driver's job easier. Signed-off-by:
Ben Dooks <ben-linux@flfuf.org> Signed-off-by:
-
Ben Dooks authored
The current S3C24XX DMA code does not allow for an peripheral that has one channel for RX and another for TX. This patch adds a per-cpu dma operation to select the transmit or receive channel, and adds support to the S3C2412 for the seperate DMA channels for TX and RX. Signed-off-by:
-
Ben Dooks authored
Add s3c2412_gpio_set_sleepcfg() to allow the setting of the sleep configuration of the GPIO blocks. Signed-off-by:
-
Ben Dooks authored
Add armclk to the S3C2412 to indicate the current clock connected to the ARM core. Signed-off-by:
-
Ben Dooks authored
Add checks for clk_set_rate() and ensure that we do not allow set_rate to be called for a clock that does not have it defined. Add default methods for fclk, hclk, pclk and mpll. Signed-off-by:
-
Krzysztof Helt authored
This patch fixes compilation error if only a machine with s3c2442 cpu is selected but without s3c2440 cpu selected. Signed-off-by:
Krzysztof Helt <krzysztof.h1@wp.pl> Acked-by:
-
Ben Dooks authored
Check if the sleep command returns due to a pending interrupt in the standby unit. If this happens, try and ack the IRQ before re-trying the resume. It is currently unclear whether the resume can be backed out of at this stage as this could cause a problem with level based interrupts. Signed-off-by:
-
Ben Dooks authored
Ensure that if the RTC IRQ is not selected for wake in the base configuration, then the PWRCFG has the same value set in it. Signed-off-by:
-
Ben Dooks authored
The IIS device is being registered by the Simtec Audio driver, and thus registering here causes an error due to device tree naming collision. Signed-off-by:
-
Ben Dooks authored
The IIS device is being registered by the Simtec Audio driver, and thus registering here causes an error due to device tree naming collision. Signed-off-by:
-
Ben Dooks authored
S3C2412_GPESLPCON does not exist in the register mappings, so remove it. Signed-off-by:
-
Ben Dooks authored
The S3C2412 IIS engine differs from the previous SoC in the range, so add a set of register definitions in a seperate file for it. Signed-off-by:
-
Ben Dooks authored
The IIS and SDI register hw_addr definitions are incorrect in the DMA map for the S3C2412. Signed-off-by:
-
Ben Dooks authored
The S3C2412 GPIO is similar enough to the S3C2410 that it can use it as a base for GPIO functionality. Signed-off-by:
-
Ben Dooks authored
We have a default display set to 4, when we only have three registered displays. Fix this argument (a seperate patch has been generated to ensure that the LCD driver takes notice of this bug) Signed-off-by:
-
Ben Dooks authored
If the watchdog reset fails and we decided to take the jump to zero approach, allow 50ms for the UARTS to drain the FIFOs before calling into a bootloader that may flush the output. Also reduece the waits and the timeout values as 5 seconds is rather long. Signed-off-by:
-
Ben Dooks authored
If the hard reset routine is using the watchdog, then ensure that the clock for the watchdog has been enabled before we try and issue a reset. Signed-off-by:
-
Ben Dooks authored
Add the S3C2412_PWRCFG values for the action taken on detecting that the battery is flat. Signed-off-by:
-
Ben Dooks authored
Add S3C2412 register definitions. Signed-off-by:
-
Daniel Mack authored
This patch adds support for Toradex' PXA27x based Colibri module. It's kept as simple as possible to only provide basic functionality. A default config is also included. Signed-off-by:
Daniel Mack <daniel@caiaq.de> Signed-off-by:
-
Russell King authored
Fix all those PXA mci_init functions which return -1 rather than propagating the error code to the higher levels. Remove the silly set_irq_type() calls as well - use the flags for request_irq() instead. Signed-off-by: -
Richard Purdie authored
This patch refactors the code in corgi_lcd.c moving it to the board specific corgi and spitz files where appropriate instead of the existing ifdef mess which hinders readability. Fix spitz_get_hsync_len() to call get_hsync_invperiod so pxafb can be compiled as a module. The confusing variables which represent the inverse horizintal sync period are renamed to "invperiod" consistently. An incorrect comment in corgi_ts.c is also corrected. Signed-off-by:
Richard Purdie <rpurdie@rpsys.net> Signed-off-by:
-
Robert Schwebel authored
This patch adds baseboard support for the phyCORE-PXA270 development kit (aka PCM-990). This example shows how to use some phyCORE-PXA270 CPU module features on a baseboard in a standard manner. It could be used as a starting point for custom baseboard development. V2: After comments by Eric Miao: - IRQ chained handler fixed - video/graphic support moved to separate patch - ifdef/endif hell reduced ;-) V3: After comments by Russell King - initialise the mmci platform data statically V4: After comments by Russell King - wrong return value in pcm990_mci_init() fixed Signed-off-by:
Juergen Beisert <j.beisert@pengutronix.de> Signed-off-by:
-
