- 20 Jul, 2017 39 commits
-
-
Sakari Ailus authored
Simplify the code to satisfy Linux coding style. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by:
Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Colin Ian King authored
Don't populate array dib0090_tuning_table_cband_7090e_aci on the stack but instead make it static. Makes the object code smaller by over 180 bytes: Before: text data bss dec hex filename 40052 7320 192 47564 b9cc dib0090.o After: text data bss dec hex filename 39780 7408 192 47380 b914 dib0090.o Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Colin Ian King authored
Don't populate const arrays on the stack but instead make them static. Makes the object code smaller by over 1800 bytes: Before: text data bss dec hex filename 94100 9160 0 103260 1935c drxj.o After: text data bss dec hex filename 91044 10400 0 101444 18c44 drxj.o Signed-off-by:
-
Colin Ian King authored
Don't populate arrays slowIncrDecLUT and fastIncrDecLUT on the stack but instead make them static. Makes the object code smaller by over 100 bytes: text data bss dec hex filename 27776 832 64 28672 7000 drxd_hard.o text data bss dec hex filename 27530 976 64 28570 6f9a drxd_hard.o Signed-off-by:
-
Daniel Scheller authored
Discovered using w_scan when scanning DVB-T/T2: When w_scan goes from -T to -T2, it does so without stopping the frontend using .sleep. Due to this, the demod operation mode isn't re-setup, but as it still is in STATE_ACTIVE_TC, PLP and T2 Profile are set up, but only retune_active() is called, leaving the demod in T mode, thus not operable on any T2 frequency. Fix this by putting the demod to sleep if priv->system isn't equal to p->delsys. To properly accomplish this, sleep_tc() is split into sleep_tc() and shutdown_tc(), where sleep_tc() will only perform the sleep operation, while shutdown_tc() additionally performs the full demod shutdown (to keep the behaviour when the .sleep FE_OP is called). Signed-off-by:
Daniel Scheller <d.scheller@gmx.net> Signed-off-by:
-
Colin Ian King authored
Don't populate array gamma_par_mask on the stack but instead make it static. Makes the object code smaller by 148 bytes: Before: text data bss dec hex filename 2993 1104 0 4097 1001 drivers/staging/fbtft/fb_st7789v.o After: text data bss dec hex filename 2757 1192 0 3949 f6d drivers/staging/fbtft/fb_st7789v.o Signed-off-by:
-
Colin Ian King authored
Don't populate arrays on the stack but make them static. Makes the object code smaller: Before: text data bss dec hex filename 89299 21704 64 111067 1b1db cxd2841er.o After: text data bss dec hex filename 85823 23432 64 109319 1ab07 cxd2841er.o Signed-off-by:
-
Akihiro Tsukada authored
When a user starts and stops filtering at a demux device too quickly in a very short interval, the user process hangs in uninterruptible sleep, due to an inconsistency of kthread status in the driver. The kthread can be stopped before it starts running its thread function, but the invocation status was partly managed in the kthread function, which resulted in a double kthread_stop() of one kthread. Signed-off-by:
Akihiro Tsukada <tskd08@gmail.com> Signed-off-by:
-
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by:Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by:
-
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for i2c_algorithm structures that are only stored in the algo field of an i2c_adapter structure. This field is declared const, so i2c_algorithm structures that have this property can be declared as const also. This issue was identified using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct i2c_algorithm i@p = { ... }; @ok@ identifier r.i; struct i2c_adapter e; position p; @@ e.algo = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; @@ i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct i2c_algorithm i = { ... }; Signed-off-by: -
Daniel Scheller authored
Return 0 instead of -EINVAL in get_frontend if no demod mode is active. This fixes ie. dvb-fe-tool getting confused and assuming a DVBv3 FE on idle frontends when the FE has been put to sleep using sleep(). Also, in read_status(), don't immediately return when no demod is active, so the remaining code has a chance to clear the signal statistics. Signed-off-by:
-
Daniel Scheller authored
Signed-off-by:
-
Daniel Scheller authored
Adds a stv0910_single modparm which, when set, configures the stv0910 to run in single demodulator mode, currently intended for high bit rate testing. Signed-off-by:
Richard Scobie <r.scobie@clear.net.nz> Signed-off-by:
-
Daniel Scheller authored
This adds all required glue code to support - in conjunction with the new stv0910 and stv6111 demod/tuner drivers and additionally the lnbh25 LNB controller driver - all current DVB-S/S2 hardware (bridges and flex modules) from Digital Devices like the DD CineS2 V7 and V7A, current S2 V4 DuoFlex modules, and probably all upcoming devices based on this STV0910/STV6111/LNBH25 hardware stack. Signed-off-by:
-
Daniel Scheller authored
The returned value is required for further evaluation of the exact demodulator chip (stv090x or stv0910). Signed-off-by:
-
Daniel Scheller authored
This adds a frontend driver for the ST STV6111 DVB-S/S2 tuners. Like the stv0910 demod frontend driver, this driver originates from the Digital Devices' dddvb vendor driver package as of version 0.9.29, and was cleaned up aswell. No functionality had to be removed though. Any camel case has been converted to kernel_case, fixup patch has been proposed upstream. Permission to reuse and mainline the driver code was formally granted by Ralph Metzler <rjkm@metzlerbros.de>. Signed-off-by:
-
Daniel Scheller authored
This was missing from the frontend_ops. Signed-off-by:
-
Daniel Scheller authored
Original code at least has some signed/unsigned issues, resulting in values like 32dBm. Implement signal strength readout to work without asking the attached tuner, and use a lookup table instead of log calc. Values reported appear plausible, gathered from feedback from several testers. Signed-off-by:
-
Daniel Scheller authored
Implements stream_id filter and scrambling code setup in start() and also sets FE_CAN_MULTISTREAM in frontend_ops. This enables the driver to properly receive and handle multistream transponders, functionality has been reported working fine by testers with access to such streams, in conjunction with VDR on the userspace side. The code snippet originates from the original vendor's dddvb driver package and has been made working properly with the current in-kernel DVB core API. Signed-off-by:
-
Daniel Scheller authored
Fixes smatch error: drivers/media/dvb-frontends/stv0910.c:715 dvbs2_nbch() error: buffer overflow 'nbch[fectype]' 2 <= 28 Also, fixes the nbch array table by adding the DUMMY_PLF element at the top to match the enums (table element order was off by one before). Patch sent upstream aswell. Cc: Ralph Metzler <rjkm@metzlerbros.de> Signed-off-by:
-
Daniel Scheller authored
This adds a multi frontend driver for the ST STV0910 DVB-S/S2 demodulator frontends. The driver code originates from the Digital Devices' dddvb vendor driver package as of version 0.9.29, and has been cleaned up from core API usage which isn't supported yet in the kernel, and additionally all obvious style issues have been resolved. All camel case and allcaps have been converted to kernel_case and lowercase. Patches have been sent to the vendor package maintainers to fix this aswell. Signal statistics acquisition has been refactored to comply with standards. Permission to reuse and mainline the driver code was formally granted by Ralph Metzler <rjkm@metzlerbros.de>. Signed-off-by:
-
Philipp Zabel authored
Now that the multiplexer framework is merged, drop the temporary mmio-mux implementation from the video-mux driver and convert it to use the multiplexer API. [mchehab@s-opensource.com: fix a merge conflict at Kconfig] Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Arnd Bergmann authored
gcc-7 notices that we copy a fixed length string into another string of the same size, with additional characters: drivers/media/usb/usbvision/usbvision-i2c.c: In function 'usbvision_i2c_register': drivers/media/usb/usbvision/usbvision-i2c.c:190:36: error: '%d' directive writing between 1 and 11 bytes into a region of size between 0 and 47 [-Werror=format-overflow=] sprintf(usbvision->i2c_adap.name, "%s-%d-%s", i2c_adap_template.name, ^~~~~~~~~~ drivers/media/usb/usbvision/usbvision-i2c.c:190:2: note: 'sprintf' output between 4 and 76 bytes into a destination of size 48 Using snprintf() makes the code more robust in general, but will still trigger a possible warning about truncation in the string. We know this won't happen as the template name is always "usbvision", so we can easily avoid the warning as well by using this as the format string directly. Signed-off-by:Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Todor Tomov authored
Add helper functions for mbus to/from mplane pixel format conversion. Signed-off-by:
Todor Tomov <todor.tomov@linaro.org> Signed-off-by:
-
Ulrich Hecht authored
Fixes a crash on Renesas R8A7793 Gose board that uses these "compatible" entries. Signed-off-by:
Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Tested-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Anton Sviridenko authored
This patch enables support for non-Bluecherry labeled solo6110 based PCI cards which have 3 x TW2864B chips and one TW2865. These cards are displayed by lspci -nn as "Softlogic Co., Ltd. SOLO6110 H.264 Video encoder/decoder [9413:6110]" Bluecherry cards have 4 x TW2864A. According to datasheet register 0xFF of TW2864B chips contains value 0x6A or 0x6B depending on revision which being shifted 3 bits right gives value 0x0d. Existing version of solo6x10 fails on these cards with [276582.344942] solo6x10 0000:07:00.0: Probing Softlogic 6110 [276582.402151] solo6x10 0000:07:00.0: Could not initialize any techwell chips [276582.402781] solo6x10: probe of 0000:07:00.0 failed with error -22 Signed-off-by:
Anton Sviridenko <anton@corp.bluecherry.net> Acked-by:
Andrey Utkin <andrey_utkin@fastmail.com> Signed-off-by:
-
Ramesh Shanmugasundaram authored
Add r8a7796 DRIF bindings. Signed-off-by:
Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
- 19 Jul, 2017 1 commit
-
-
Mauro Carvalho Chehab authored
drivers/media/i2c/adv748x/adv748x-csi2.c: In function 'adv748x_csi2_init_controls': drivers/media/i2c/adv748x/adv748x-csi2.c:251:20: warning: variable 'ctrl' set but not used [-Wunused-but-set-variable] struct v4l2_ctrl *ctrl; ^~~~ Signed-off-by:
-
