- 28 Jan, 2009 40 commits
-
-
Casey Schaufler authored
Given just how hard it is to find the code that uses MAY_APPEND it's probably not a big surprise that this went unnoticed for so long. The Smack rules loading code is incorrectly setting the MAY_READ bit when MAY_APPEND is requested. Signed-off-by:
Casey Schaufler <casey@schaufler-ca.com> Reviewed-by:
James Morris <jmorris@namei.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (36 commits) USB: Driver for Freescale QUICC Engine USB Host Controller USB: option: add QUANTA HSDPA Data Card device ids USB: storage: Add another unusual_dev for off-by-one bug USB: unusual_dev: usb-storage needs to ignore a device USB: GADGET: fix !x & y USB: new id for ti_usb_3410_5052 driver USB: cdc-acm: Add another conexant modem to the quirks USB: 'option' driver - onda device MT503HS has wrong id USB: Remove ZTE modem from unusual_devices USB: storage: support of Dane-Elec MediaTouch USB device USB: usbmon: Implement compat_ioctl USB: add kernel-doc for wusb_dev in struct usb_device USB: ftdi_sio driver support of bar code scanner from Diebold USB: ftdi_sio: added Alti-2 VID and Neptune 3 PID USB: cp2101 device USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440 USB: remove vernier labpro from ldusb USB: CDC-ACM quirk for MTK GPS USB: cdc-acm: support some gps data loggers USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index ...
-
Anton Vorontsov authored
This patch adds support for the FHCI USB controller, as found in the Freescale MPC836x and MPC832x processors. It can support Full or Low speed modes. Quite a lot the hardware is doing by itself (SOF generation, CRC generation and checking), though scheduling and retransmission is on software's shoulders. This controller does not integrate the root hub, so this driver also fakes one-port hub. External hub is required to support more than one device. Signed-off-by:
Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Alex.Cheng@quantatw.com authored
This patch adds the support for the QUANTA Q101 series HSDPA Data Card. With the vendor and product IDs are set properly, the data card can be detected and works fine. Signed-off-by:
Alex Cheng <alex.cheng@quantatw.com> Signed-off-by:
-
Phil Dibowitz authored
Argosy has released another device with the off-by-one sector. This is a harddrive with an internal cardreader which is affected. Based on a patch written by Martijn Hijdra <martijn.hijdra@gmail.com> Signed-off-by:
Phil Dibowitz <phil@ipom.com> Cc: Martijn Hijdra <martijn.hijdra@gmail.com> Signed-off-by:
-
Phil Dibowitz authored
This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many other modems, we have to ignore the storage device in order to access the modem. At this time usb_modeswitch does not work with this device. Reported-by: The Solutor <thesolutor@gmail.com>. Signed-off-by:
-
Roel Kluin authored
! has a higher precedence than & Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Acked-by:
David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
Oliver Neukum authored
This adds a new device id Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Alan Cox authored
Another Conexant, another device with the same quirk Signed-off-by:
Alan Cox <alan@redhat.com> Acked-by:
Oliver Neukum <oliver@neukum.org> Signed-off-by:
-
Marcel Sebek authored
While trying to make GSM modem Onda MT503HS working, I found a mismatch between device id in the driver code (0x0200) and id in the lsusb output (0x2000). This patch fixed it for me, but I don't know if the original device id was also correct and the new ID should be added instead of replacing the old one. Signed-off-by:
Marcel Sebek <sebek64@post.cz> Acked-by:
Domenico Riccio <domenico.riccio@gmail.com> Signed-off-by:
-
Phil Dibowitz authored
The ZTE modem entry causes usb-storage to ignore the device, but for some versions of the device, usb-storage mode is required to get to modem ode. For both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work. Note that the various versions of the device have the same ProductId, VendorId, and bcdDevice number, so we cannot have the entry for some and not others. Signed-off-by:
-
Jean-Baptiste Onofre authored
This adds another unusual_devs.h entry for a device that can't handle more than 64k reads/writes in a single command. Signed-off-by:
Jean-Baptiste Onofre <jb@nanthrax.net> Signed-off-by:
-
Pete Zaitcev authored
Running a 32-bit usbmon(8) on 2.6.28-rc9 produces the following: ioctl32(usbmon:28563): Unknown cmd fd(3) cmd(400c9206){t:ffffff92;sz:12} arg(ffd3f458) on /dev/usbmon0 It happens because the compatibility mode was implemented for 2.6.18 and not updated for the fsops.compat_ioctl API. This patch relocates the pieces from under #ifdef CONFIG_COMPAT into compat_ioctl with no other changes except one new whitespace. Signed-off-by:Pete Zaitcev <zaitcev@redhat.com> Cc: stable <stable@kernel.org> Signed-off-by:
-
Inaky Perez-Gonzalez authored
Reported by Randy Dunlap from a warning on the v2.6.29 merge window. Signed-off-by:
Inaky Perez-Gonzalez <inaky@linux.intel.com> Cc: David Vrabel <david.vrabel@csr.com> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Mhayk Whandson authored
Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil. Signed-off-by:
Mhayk Whandson <eu@mhayk.com.br> Signed-off-by:
-
Robie Basak authored
This patch adds the vendor and product ID for the Alti-2 Neptune 3 (http://www.alti-2.com) which uses the FTDI chip. Signed-off-by:
Robie Basak <rb-oss-1@justgohome.co.uk> Signed-off-by:
-
Tomasz K authored
My girl use modem GSM (EDGE) Commanader 2 on iPlus Polsih provider, PLEASE add this vendor=0x10C4 and product=0x822B to USB serial driver cp2101.c From: Tomasz K <eros81@o2.pl> Signed-off-by: -
Brandon Philips authored
My Brother HL-1440 would print one document before CUPS would stop printing with the error "Printer not connected; will retry in 30 seconds...". I traced this down to the CUPS usb backend getting an EIO out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the USBLP_QUIRK_BIDIR fixes the problem but is it the right solution? output from strace /usr/lib/cups/backend/usb after printing a document (Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID): before patch open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3 ioctl(3, SNDCTL_DSP_SYNC, 0x7fff2478cef0) = -1 EIO (Input/output error) after patch open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3 ioctl(3, SNDCTL_DSP_SYNC, 0x7fffb8d474c0) = 0 Possibly related bug: https://bugs.launchpad.net/ubuntu/+source/cupsys/+bug/35638Signed-off-by:Brandon Philips <bphilips@suse.de> Signed-off-by:
-
sware authored
Labpro device is in both ldusb and vstusb device tables. Should only be a vstusb device. Signed-off-by:
stephen ware <stephen.ware@eqware.net> Signed-off-by:
-
Andrew Lunn authored
This patch adds a device quirk for a MediaTek Inc GPS chipset. The device implements USB CDC ACM, but is missing the union descriptor, so the ACM class driver fails to probe the device. I've tested this patch with an iBlue A+ GPS which uses this chipset and using kernel 2.6.28-rc9. Signed-off-by:
Andrew Lunn, <andrew@lunn.ch> Acked-by:
-
James A. Treacy authored
Below is a patch which allows a number of GPS loggers to work under linux. It is known to support the i-Blue 747 (all models), i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux M-241. From: James A. Treacy <treacy@debian.org> Signed-off-by: -
Bryan Wu authored
USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index In some usb gadget driver, for example usb audio class device, the high byte of w_index is the entity id and low byte is the interface number. If we use the 2 bytes of w_index as the array number, we will get a wrong pointer or NULL pointer. This patch fixes this issue. Signed-off-by:
Bryan Wu <cooloney@kernel.org> Acked-by:
-
Bryan Wu authored
Signed-off-by:
-
David Brownell authored
The Blackfin MUSB Kconfig text didn't properly parenthesise its dependencies. This was visible in non-Blackfin configs by the way the user interfaces lost track of dependencies, when doing a bunch of test builds. Signed-off-by:
-
Swaminathan S authored
Initializes the actual_len field to 0 before every DMA transaction. Signed-off-by:
Swaminathan S <swami.iyer@ti.com> Acked-by:
Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by:
-
Hugo Villeneuve authored
These compilation errors are related to incorrect debugging macro and variable names and generated the following errors: drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment': drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function) Signed-off-by:
Hugo Villeneuve <hugo@hugovil.com> Signed-off-by:
-
Julia Lawall authored
This set of patches introduces calls to the following set of functions: usb_endpoint_dir_in(epd) usb_endpoint_dir_out(epd) usb_endpoint_is_bulk_in(epd) usb_endpoint_is_bulk_out(epd) usb_endpoint_is_int_in(epd) usb_endpoint_is_int_out(epd) usb_endpoint_num(epd) usb_endpoint_type(epd) usb_endpoint_xfer_bulk(epd) usb_endpoint_xfer_control(epd) usb_endpoint_xfer_int(epd) usb_endpoint_xfer_isoc(epd) In some cases, introducing one of these functions is not possible, and it just replaces an explicit integer value by one of the following constants: USB_ENDPOINT_XFER_BULK USB_ENDPOINT_XFER_CONTROL USB_ENDPOINT_XFER_INT USB_ENDPOINT_XFER_ISOC An extract of the semantic patch that makes these changes is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r1@ struct usb_endpoint_descriptor *epd; @@ - ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) == - \(USB_ENDPOINT_XFER_CONTROL\|0\)) + usb_endpoint_xfer_control(epd) @r5@ struct usb_endpoint_descriptor *epd; @@ - ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) == - \(USB_DIR_IN\|0x80\)) + usb_endpoint_dir_in(epd) @inc@ @@ #include <linux/usb.h> @depends on !inc && (r1||r5)@ @@ + #include <linux/usb.h> #include <linux/usb/...> // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Acked-by:
-
Kalle Valo authored
drivers/usb/musb/tusb6010_omap.c:18:26: error: asm/arch/dma.h: No such file or directory drivers/usb/musb/tusb6010_omap.c:19:26: error: asm/arch/mux.h: No such file or directory Signed-off-by:
Kalle Valo <kalle.valo@nokia.com> Acked-by:
-
Ajay Kumar Gupta authored
Fixes insert module failure as free_irq() was not done in previous rmmod. Signed-off-by:
Ajay Kumar Gupta <ajay.gupta@ti.com> Acked-by:
-
David Brownell authored
The DaVinci code had an implementation of the OTG transceiver glue too; make it use the new-standard one. Signed-off-by:
-
David Brownell authored
Trying once more to get this merged. The original was submitted for 2.6.27-rc2 or so, and never got correctly merged. Neither were any of the numerous subsequent resends. Sigh. CC drivers/usb/musb/davinci.o drivers/usb/musb/davinci.c:35:32: error: mach/arch/hardware.h: No such file or directory drivers/usb/musb/davinci.c:36:30: error: mach/arch/memory.h: No such file or directory drivers/usb/musb/davinci.c:37:28: error: mach/arch/gpio.h: No such file or directory drivers/usb/musb/davinci.c:373: error: redefinition of 'musb_platform_set_mode' drivers/usb/musb/davinci.c:368: error: previous definition of 'musb_platform_set_mode' was here Signed-off-by:
-
David Brownell authored
> > drivers/built-in.o: In function `ohci_omap_init': > > hid-quirks.c:(.text+0x6c608): undefined reference to `otg_get_transceiver' > > drivers/built-in.o: In function `omap_udc_probe': > > hid-quirks.c:(.init.text+0x34c0): undefined reference to `otg_get_transceiver' > > hid-quirks.c:(.init.text+0x3d40): undefined reference to `otg_put_transceiver' Reported-by:
Russell King <linux@arm.linux.org.uk> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Alan Stern authored
This patch (as1198) fixes a conceptual bug: Somewhere along the line we managed to confuse USB class devices with USB char devices. As a result, the code to send a disconnect signal to userspace would not be built if both CONFIG_USB_DEVICE_CLASS and CONFIG_USB_DEVICEFS were disabled. The usb_fs_classdev_common_remove() routine has been renamed to usbdev_remove() and it is now called whenever any USB device is removed, not just when a class device is unregistered. The notifier registration and unregistration calls are no longer conditionally compiled. And since the common removal code will always be called as part of the char device interface, there's no need to call it again as part of the usbfs interface; thus the invocation of usb_fs_classdev_common_remove() has been taken out of usbfs_remove_device(). Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Alon Bar-Lev <alon.barlev@gmail.com> Tested-by:
-
Rafael J. Wysocki authored
Commit a0d4922d (USB: fix up suspend and resume for PCI host controllers) attempted to fix the suspend-resume of PCI USB controllers, but unfortunately it did that incorrectly and interrupts are left enabled by the USB controllers' ->suspend_late() callback as a result. This leads to serious problems during suspend which are very difficult to debug. Fix the issue by removing the ->suspend_late() callback of PCI USB controllers and moving the code from there to the ->suspend() callback executed with interrupts enabled. Additionally, make the ->resume() callback of PCI USB controllers execute pci_enable_wake(dev, PCI_D0, false) to disable wake-up from the full power state (PCI_D0). Signed-off-by:
Rafael J. Wysocki <rjw@sisk.pl> Tested-by:
Andrey Borzenkov <arvidjaar@mail.ru> Tested-by:
"Jeff Chua" <jeff.chua.linux@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: "Zdenek Kabelac" <zdenek.kabelac@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by:
-
Alan Stern authored
This patch (as1199) changes the initial wakeup settings for PCI USB host controllers. The controllers are marked as capable of waking the system, but wakeup is not enabled by default. It turns out that enabling wakeup for USB host controllers has a lot of bad consequences. As the simplest example, if a USB mouse or keyboard is unplugged immediately after the computer is put to sleep, the unplug will cause the system to wake back up again! We are better off marking them as wakeup-capable and leaving wakeup disabled. Signed-off-by:
-
Oliver Neukum authored
This adds an unusual devs entry for 2116:0320 Signed-off-by:
-
Alan Stern authored
This patch (as1200) finishes some fixes that were left incomplete by an earlier patch. Although nobody has addressed this issue in the past, it turns out that we need to distinguish between two different modes of disabling and enabling endpoints. In one mode only the data structures in usbcore are affected, and in the other mode the host controller and device hardware states are affected as well. The earlier patch added an extra argument to the routines in the enable_endpoint pathways to reflect this difference. This patch adds corresponding arguments to the disable_endpoint pathways. Without this change, the endpoint toggle state can get out of sync between the host and the device. The exact mechanism depends on the details of the host controller (whether or not it stores its own copy of the toggle values). Signed-off-by:
Dan Streetman <ddstreet@ieee.org> Tested-by:
-
Wolfgang Glas authored
This adds the vendor/product ID of the fasttrax GPS evaluation kit from: http://www.fastraxgps.com/products/evaluationtools/evaluationkit/ to the cp2101 module since this device is actually equipped with a CP210x USB to serial bridge. The vendor/product ID is: 0x10c4/0x826b. Signed-off-by:
Wolfgang Glas <wolfgang.glas@ev-i.at> Signed-off-by:
-
git://linux-nfs.org/~bfields/linuxLinus Torvalds authored
* 'for-2.6.29' of git://linux-nfs.org/~bfields/linux: nfsd: only set file_lock.fl_lmops in nfsd4_lockt if a stateowner is found nfsd: fix cred leak on every rpc nfsd: fix null dereference on error path nfs: note that CONFIG_SUNRPC_XPRT_RDMA turns on server side support too update port number in NFS/RDMA documentation
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: [SCSI] ibmvfc: Fix DMA mapping leak on memory allocation failure [SCSI] qla2xxx: Update version number to 8.03.00-k2. [SCSI] qla2xxx: Add checks for a valid fcport in dev-loss-tmo/terminate_rport_io callbacks. [SCSI] qla2xxx: Correct regression in DMA-mask setting prior to allocations. [SCSI] qla2xxx: Correct descriptions in flash manipulation routines. [SCSI] qla2xxx: Correct regression in EH abort handling. [SCSI] qla2xxx: Correct endianness issue during flash manipulation. [SCSI] qla2xxx: Correct MSI-X vector allocation for single queue mode. [SCSI] qla2xxx: Modify firmware-load order precedence for ISP81XX parts. [SCSI] qla2xxx: Always serialize mailbox command execution. [SCSI] qla2xxx: Ensure RISC-interrupt-enabled consistency for IS_NOPOLLING_TYPE() ISPs. [SCSI] qla2xxx: Simplify sector-mask calculation in preparation for larger flash parts. [SCSI] qla2xxx: Fix memory leak in error path [SCSI] qla4xxx: do not reuse session when connecting to different target port [SCSI] libiscsi: fix iscsi pool leak
-
