The MDIO bus drivers for the UCC and gianfar ethernet controllers are
essentially the same.  There's no reason to duplicate that much code.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Many physical NICs let the OS re-program the "hardware" MAC
address.  Virtual NICs should allow this too.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VLAN filtering allows the hypervisor to drop packets from VLANs
that we're not a part of, further reducing the number of extraneous
packets recieved.  This makes use of the VLAN virtqueue command class.
The CTRL_VLAN feature bit tells us whether the backend supports VLAN
filtering.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of the MAC control virtqueue class to support a MAC
filter table.  The filter table is managed by the hypervisor.
We consider the table to be available if the CTRL_RX feature
bit is set.  We leave it to the hypervisor to manage the table
and enable promiscuous or all-multi mode as necessary depending
on the resources available to it.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of the RX_MODE control virtqueue class to enable the
set_rx_mode netdev interface.  This allows us to selectively
enable/disable promiscuous and allmulti mode so we don't see
packets we don't want.  For now, we automatically enable these
as needed if additional unicast or multicast addresses are
requested.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This will be used for RX mode, MAC filter table, VLAN filtering, etc...

The control transaction consists of one or more "out" sg entries and
one or more "in" sg entries.  The first out entry contains a header
defining the class and command.  Additional out entries may provide
data for the command.  The last in entry provides a status response
back from the command.

Virtqueues typically run asynchronous, running a callback function
when there's data in the channel.  We can't readily make use of this
in the command paths where we need to use this.  Instead, we kick
the virtqueue and spin.  The kick causes an I/O write, triggering an
immediate trap into the hypervisor.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

S2IO driver is printing dev->name before the name being allocated, which
display eth%d instead of eth0, eth1, etc. Example: 

eth%d: Enabling MSIX failed
eth%d: MSI-X requested but failed to enable

This patch just change eth%d to s2io.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Read configuration register during probe and use it to size the
available VPD. Move existing code using same register slightly
earlier in probe handling.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VPD stuff has more data and isn't generally that useful, so move
it into the existing debugfs display and use the new PCI VPD
accessor routines.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On non-x86 platforms it is possible to run out of DMA mapping resources.
The driver was ignoring this and could cause corruptions.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This workaround is not needed. It was inherited from sk98lin driver but only
applies to an early development version of the chip that is not supported
by sky2.  The workaround required an unnecessary pci read which hurts performance
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/Kconfig

Michael Tokarev wrote:
[]
> 2, and this is the main one: How about supplementary groups?
>
> Here I have a valid usage case: a group of testers running various
> versions of windows using KVM (kernel virtual machine), 1 at a time,
> to test some software.  kvm is set up to use bridge with a tap device
> (there should be a way to connect to the machine).  Anyone on that group
> has to be able to start/stop the virtual machines.
>
> My first attempt - pretty obvious when I saw -g option of tunctl - is
> to add group ownership for the tun device and add a supplementary group
> to each user (their primary group should be different).  But that fails,
> since kernel only checks for egid, not any other group ids.
>
> What's the reasoning to not allow supplementary groups and to only check
> for egid?
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change spin_locks to irqsave to prevent dead-locks.
Protect adding and deleting to/from dca_providers list.
Drop the lock during dca_sysfs_add_req() and dca_sysfs_remove_req() calls
as they might sleep (use GFP_KERNEL allocation).
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netlink connector uses its own workqueue to relay the datas sent
from userspace to the appropriate callback.  If you launch the test
from Documentation/connector and change it a bit to send a high flow
of data, you will see thousands of events coming to the "cqueue"
workqueue by looking at the workqueue tracer.

This flow of events can be sent very quickly. So, to not encumber the
kevent workqueue and delay other jobs, the "cqueue" workqueue should
remain.

But this workqueue is pointless most of the time, it will always be
created (assuming you have built it of course) although only
developpers with specific needs will use it.

So avoid this "most of the time useless task", this patch proposes to
create this workqueue only when needed once.  The first jobs to be
sent to connector callbacks will be sent to kevent while the "cqueue"
thread creation will be scheduled to kevent too.

The following jobs will continue to be scheduled to keventd until the
cqueue workqueue is created, and then the rest of the jobs will
continue to perform as usual, through this dedicated workqueue.

Each time I tested this patch, only the first event was sent to
keventd, the rest has been sent to cqueue which have been created
quickly.

Also, this patch fixes some trailing whitespaces on the connector files.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

while (limit--)
	if (test())
		break;

if (limit <= 0)
	goto test_failed;

In the last iteration, limit is decremented after the test to 0.
If just thereafter test() succeeds and a break occurs, the goto
still occurs because limit is 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

while (timeout--) { ... }

timeout becomes -1 if the loop isn't ended otherwise, not 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI hotplug: Change link order of pciehp & acpiphp
  PCI hotplug: fakephp: Allocate PCI resources before adding the device
  PCI MSI: Fix undefined shift by 32
  PCI PM: Do not wait for buses in B2 or B3 during resume
  PCI PM: Power up devices before restoring their state
  PCI PM: Fix hibernation breakage on EeePC 701
  PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs
  PCI PM: Fix suspend error paths and testing facility breakage

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  slub: fix per cpu kmem_cache_cpu array memory leak
  kmalloc: return NULL instead of link failure

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks
  powerpc: Fix oops on some machines due to incorrect pr_debug()
  powerpc/ps3: Printing fixups for l64 to ll64 convserion drivers/net
  powerpc/5200: update device tree binding documentation
  powerpc/5200: Bugfix for PCI mapping of memory and IMMR
  powerpc/5200: update defconfigs

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched_rt: don't use first_cpu on cpumask created with cpumask_and
  sched: fix buddie group latency
  sched: clear buddies more aggressively
  sched: symmetric sync vs avg_overlap
  sched: fix sync wakeups
  cpuset: fix possible deadlock in async_rebuild_sched_domains

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (45 commits)
  V4L/DVB (10411): s5h1409: Perform s5h1409 soft reset after tuning
  V4L/DVB (10403): saa7134-alsa: saa7130 doesn't support digital audio
  V4L/DVB (10229): ivtv: fix memory leak
  V4L/DVB (10385): gspca - main: Fix memory leak when USB disconnection while streaming.
  V4L/DVB (10325): em28xx: Fix for fail to submit URB with IRQs and Pre-emption Disabled
  V4L/DVB (10317): radio-mr800: fix radio->muted and radio->stereo
  V4L/DVB (10314): cx25840: ignore TUNER_SET_CONFIG in the command callback.
  V4L/DVB (10288): af9015: bug fix: stick does not work always when plugged
  V4L/DVB (10287): af9015: fix second FE
  V4L/DVB (10270): saa7146: fix unbalanced mutex_lock/unlock
  V4L/DVB (10265): budget.c driver: Kernel oops: "BUG: unable to handle kernel paging request at ffffffff
  V4L/DVB (10261): em28xx: fix kernel panic on audio shutdown
  V4L/DVB (10257): em28xx: Fix for KWorld 330U Board
  V4L/DVB (10256): em28xx: Fix for KWorld 330U AC97
  V4L/DVB (10254): em28xx: Fix audio URB transfer buffer race condition
  V4L/DVB (10250): cx25840: fix regression: fw not loaded on first use
  V4L/DVB (10248): v4l-dvb: fix a bunch of compile warnings.
  V4L/DVB (10243): em28xx: fix compile warning
  V4L/DVB (10240): Fix obvious swapped names in v4l2_subdev logic
  V4L/DVB (10233): [PATCH] Terratec Cinergy DT XS Diversity new USB ID (0ccd:0081)
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  pxamci: enable DMA for write ops after CMD/RESP
  pxamci: replace #ifdef CONFIG_PXA27x with if (cpu_is_pxa27x())
  ricoh_mmc: Use suspend_late/resume_early
  mmci: Add support for ST Micro derivate
  mmc: Add a MX2/MX3 specific SDHC driver

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  icside: fix PCB version 6 support (v2)
  tx4939ide: typo fix and minor cleanup
  ide: add CS5536 host driver (v3)
  ide: Force VIA IDE legacy interrupts for AmigaOne boards
  IDE: Unregister and disable devices if initialization fails.
  ide: fix ide_register_port() failure handling
  ide: struct device - replace bus_id with dev_name(), dev_set_name()
  ide-cd: fix DMA for non bio-backed requests

* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
  uwb: lock rc->rsvs_lock with spin_lock_bh()
  wusb: timeout when waiting for ASL/PZL updates in whci-hcd
  uwb: remove unused #include <version.h>'s
  wusb: return -ENOTCONN when resetting a port with no connected device
  uwb: safely remove all reservations

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: add text file detailing queue/ sysfs files
  bio.h: If they MUST be inlined, then use __always_inline
  Fix misleading comment in bio.h
  block: fix inconsistent parenthesisation of QUEUE_FLAG_DEFAULT
  block: fix oops in blk_queue_io_stat()

The host really shouldn't be notifying us of config changes
before the device status is VIRTIO_CONFIG_S_DRIVER or
VIRTIO_CONFIG_S_DRIVER_OK.

However, if we do happen to be interrupted while we're not
attached to a driver, we really shouldn't oops. Prevent
this simply by checking that device->driver is non-NULL
before trying to notify the driver of config changes.

Problem observed by doing a "set_link virtio.0 down" with
QEMU before the net driver had been loaded.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Current refcounting for modules (done if CONFIG_MODULE_UNLOAD=y) is
using a lot of memory.

Each 'struct module' contains an [NR_CPUS] array of full cache lines.

This patch uses existing infrastructure (percpu_modalloc() &
percpu_modfree()) to allocate percpu space for the refcount storage.

Instead of wasting NR_CPUS*128 bytes (on i386), we now use
nr_cpu_ids*sizeof(local_t) bytes.

On a typical distro, where NR_CPUS=8, shiping 2000 modules, we reduce
size of module files by about 2 Mbytes. (1Kb per module)

Instead of having all refcounters in the same memory node - with TLB misses
because of vmalloc() - this new implementation permits to have better
NUMA properties, since each  CPU will use storage on its preferred node,
thanks to percpu storage.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without this the 2nd port gets first ports MAC addr.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 93821778 (udp: Fix rcv socket
locking) accidentally removed sk_drops increments for UDP IPV4
sockets.

This field can be used to detect incorrect sizing of socket receive
buffers.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported by Andrew Walrond <andrew@walrond.org>

Changeset c19e654d
("gre: Add netlink interface") added an include
of linux/ip.h to linux/if_tunnel.h

We can't really let that get exposed to userspace
because this conflicts with types defined in netinet/ip.h
which userland is almost certainly going to have included
either explicitly or implicitly.

So guard this include with a __KERNEL__ ifdef.
Signed-off-by: David S. Miller <davem@davemloft.net>

With the PXA270 MMC hardware, there seems to be an issue of
data corruption on writes where a 4KB data block is offset
by one byte.

If we delay enabling the DMA for writes until after the CMD/RESP
has finished, the problem seems to be fixed.

related to PXA270 Erratum #91
Tested-by: Vernon Sauder <VernonInHand@gmail.com>
Signed-off-by: Cliff Brake <cbrake@bec-systems.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Cliff Brake <cbrake@bec-systems.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

If ricoh_mmc suspends before sdhci_pci, it will pull the card
out from under the controller, which could leave the system in
a very confused state.

Using suspend_late/resume_early ensures that sdhci_pci suspends first
and resumes second.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This patch adds support for the ST Microelectronics version of
the PL180 PrimeCell. They use designer ID 0x80 and have a few
alterations/bugfixes related to open drain and HW flow control.
They also add some SDIO registers, I am unsure if these are
in ST HW only or if this is things also added in later ARM
revisions, but they are included in the mmci.h file for
completeness.
Signed-off-by: Linus Walleij <linus.walleij@ericsson.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically
the same as in the MX1, but unlike the MX1 controller the MX2
controller just works as expected. Since the MX1 driver has more
workarounds for bugs than anything else I had no success with supporting
MX1 and MX2 in a sane way in one driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>