mt35xu02g is an Octal flash supporting Single and OCTAL I/O.
Tested on LS1028ARDB.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
[tudor.ambarus@microchip.com: reword commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

We already pass a pointer to nor, we can obtain the sector_size
by dereferencing it.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

This patch adds spi_nor_debugfs_init() for the debugfs initialization.
With this patch, we can read the partname and partid through the
debugfs.

The output of new debugfs nodes on my device are:
cat /sys/kernel/debug/mtd/mtd0/partid
spi-nor:ef6017
cat /sys/kernel/debug/mtd/mtd0/partname
w25q64dw
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Currently, we don't have vfs nodes for querying the underlying flash name
and flash id. This information is important especially when we want to
know the flash detail of the defective system. In order to support the
query, we add mtd_debugfs_populate() to create two debugfs nodes
(ie. partname and partid). The upper driver can assign the pointer to
partname and partid before calling mtd_device_register().
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a break from the middle of the loop, there
is no put, thus causing a memory leak. Hence add an of_node_put before
the break.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a break from the middle of the loop, there is
no put, thus causing a memory leak. Upon termination of the loop
(whether by break or a natural exit), either ret will have a non-zero
value or child will be NULL. Hence add an of_node_put() that will
execute only when ret has a non-zero value, as calling of_node_put() on
a possible NULL value does not cause any further issues.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Dedicate a function for getting the pointer to the flash_info
const struct. Trim a bit the spi_nor_scan() huge function.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

Parsing of flash parameters were interleaved with setting of the
nor addr width. Dedicate a function for setting nor addr width.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

Bring all flash parameters default initialization in
spi_nor_legacy_params_init().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

S3AN flashes use a specific opcode to read the status register.
We currently use the SPI_S3AN flag to decide whether this specific
SR read opcode should be used, but SPI_S3AN is about to disappear, so
let's add a new flag.

Note that we use the same bit as SPI_S3AN implies SPI_NOR_XSR_RDY and
vice versa.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

s3an_nor_scan() was overriding the opcode selection done in
spi_nor_default_setup(). Set nor->setup() method in order to
avoid the unnecessary call to spi_nor_default_setup().

Now that the call to spi_nor_default_setup() is skipped, set
mtd.erasesize to nor->info->sector_size, as it was when
spi_nor_select_erase() was called.

No dummy byte is required for the S3AN's Random Read command (0x03),
so no need to set nor->read_dummy.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

nor->params.setup() configures the SPI NOR memory. Useful for SPI NOR
flashes that have peculiarities to the SPI NOR standard, e.g.
different opcodes, specific address calculation, page size, etc.
Right now the only user will be the S3AN chips, but other
manufacturers can implement it if needed.

Move spi_nor_setup() related code in order to avoid a forward
declaration to spi_nor_default_setup().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

In order to separate manufacturer quirks from the core we need to get
rid of all the manufacturer specific flags, like the
SNOR_F_S3AN_ADDR_DEFAULT one.

This can easily be replaced by a ->convert_addr() hook, which when
implemented will provide the core with an easy way to convert an
absolute address into something the flash understands.

Right now the only user are the S3AN chips, but other manufacturers
can implement it if needed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

Add a spansion_post_sfdp_fixups() function to fix the erase opcode,
erase sector size and set the SNOR_F_4B_OPCODES flag.
This way, all spansion related quirks are placed in the
spansion_post_sfdp_fixups() function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

SFDP tables are sometimes wrong and we need a way to override the
config chosen by the SFDP parsing logic without discarding all of it.

Add a new hook called after the SFDP parsing has taken place to deal
with such problems.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

Add the SNOR_F_HAS_LOCK flag and set it when SPI_NOR_HAS_LOCK is set
in the flash_info entry or when it's a Micron or ST flash.

Move the locking hooks in a separate struct so that we have just
one field to update when we change the locking implementation.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[tudor.ambarus@microchip.com: use ->default_init() hook, introduce
spi_nor_late_init_params(), set ops in nor->params]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

The procedure used to enable 4 byte addressing mode depends on the NOR
device, so let's provide a hook so that manufacturer specific handling
can be implemented in a sane way.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[tudor.ambarus@microchip.com: use nor->params.set_4byte() instead of
nor->set_4byte()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

Add functions to delimit what the chunks of code do:

static void spi_nor_init_params()
{
	spi_nor_info_init_params()
	spi_nor_manufacturer_init_params()
	spi_nor_sfdp_init_params()
}

Add descriptions to all methods.

spi_nor_init_params() becomes of type void, as all its children
return void.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

The goal is to move the quad_enable manufacturer specific init in the
nor->manufacturer->fixups->default_init()

The legacy quad_enable() implementation is spansion_quad_enable(),
select this method by default.

Set specific manufacturer fixups->default_init() hooks to overwrite
the default quad_enable() implementation when needed.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

gd25q256 needs to tweak the ->quad_enable() implementation and the
->default_init() fixup hook is the perfect place to do that. This way,
if we ever need to tweak more things for this flash, we won't have to
add new fields in flash_info.

We can get rid of the flash_info->quad_enable field as gd25q256 was
the only user.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[tudor.ambarus@microchip.com: use ->default_init() hook instead of
->post_sfdp()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

As of now, the flash parameters initialization logic is as following:

a/ default flash parameters init in spi_nor_init_params()
b/ manufacturer specific flash parameters updates, split across entire
   spi-nor core code
c/ flash parameters updates based on SFDP tables
d/ post BFPT flash parameter updates

In the quest of removing the manufacturer specific code from the spi-nor
core, we want to impose a timeline/priority on how the flash parameters
are updated. The following sequence of calls is pursued:

1/ spi-nor core parameters init based on 'flash_info' struct:
	spi_nor_info_init_params()

which can be overwritten by:
2/ MFR-based manufacturer flash parameters init:
	nor->manufacturer->fixups->default_init()

which can be overwritten by:
3/ specific flash_info tweeks done when decisions can not be done just on
   MFR:
	nor->info->fixups->default_init()

which can be overwritten by:
4/ SFDP tables flash parameters init - SFDP knows better:
	spi_nor_sfdp_init_params()

which can be overwritten by:
5/ post SFDP tables flash parameters updates - in case manufacturers get
   the serial flash tables wrong or incomplete.
	nor->info->fixups->post_sfdp()
   The later can be extended to nor->manufacturer->fixups->post_sfdp() if
   needed.

This patch opens doors for steps 2/ and 3/.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

All flash parameters and settings should reside inside
'struct spi_nor_flash_parameter'. Move the SMPT parsed erase map
from 'struct spi_nor' to 'struct spi_nor_flash_parameter'.

Please note that there is a roll-back mechanism for the flash
parameter and settings, for cases when SFDP parser fails. The SFDP
parser receives a Stack allocated copy of nor->params, called
sfdp_params, and uses it to retrieve the serial flash discoverable
parameters. JESD216 SFDP is a standard and has a higher priority
than the default initialized flash parameters, so will overwrite the
sfdp_params data when needed. All SFDP code uses the local copy of
nor->params, that will overwrite it in the end, if the parser succeds.

Saving and restoring the nor->params.erase_map is no longer needed,
since the SFDP code does not touch it.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

All flash parameters and settings should reside inside
'struct spi_nor_flash_parameter'. Drop the local copy of
quad_enable() and use the one from 'struct spi_nor_flash_parameter'.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

The Flash parameters and settings are now stored in 'struct spi_nor'.
Use this instead of the stack allocated params.

Few functions stop passing pointer to params, as they can get it from
'struct spi_nor'. spi_nor_parse_sfdp() and children will keep passing
pointer to params because of the roll-back mechanism: in case the
parsing of SFDP fails, the legacy flash parameter and settings will be
restored.

Zeroing params is no longer needed because all SPI NOR users kzalloc
'struct spi_nor'.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

The scope is to move all [FLASH-SPECIFIC] parameters and settings
from 'struct spi_nor' to 'struct spi_nor_flash_parameter'.

'struct spi_nor_flash_parameter' describes the hardware capabilities
and associated settings of the SPI NOR flash memory. It includes
legacy flash parameters and settings that can be overwritten by the
spi_nor_fixups hooks, or dynamically when parsing the JESD216
Serial Flash Discoverable Parameters (SFDP) tables. All SFDP params
and settings will fit inside 'struct spi_nor_flash_parameter'.

Move spi_nor_hwcaps related code to avoid forward declarations.
Add a forward declaration that we can't avoid: 'struct spi_nor' will
be used in 'struct spi_nor_flash_parameter'.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

Remove leftover from nor->cmd_buf.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Linux 5.3-rc6

Merge back latest release candidate, to include a fix that
we depend on for new development:
834de5c1 ("mtd: spi-nor: Fix the disabling of write protection at init")

Pull auxdisplay cleanup from Miguel Ojeda:
 "Make ht16k33_fb_fix and ht16k33_fb_var constant (Nishka Dasgupta)"

* tag 'auxdisplay-for-linus-v5.3-rc7' of git://github.com/ojeda/linux:
  auxdisplay: ht16k33: Make ht16k33_fb_fix and ht16k33_fb_var constant

Pull UML fix from Richard Weinberger:
 "Fix time travel mode"

* tag 'for-linus-5.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: fix time travel mode

Pull UBIFS and JFFS2 fixes from Richard Weinberger:
 "UBIFS:
   - Don't block too long in writeback_inodes_sb()
   - Fix for a possible overrun of the log head
   - Fix double unlock in orphan_delete()

  JFFS2:
   - Remove C++ style from UAPI header and unbreak picky toolchains"

* tag 'for-linus-5.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
  ubifs: Limit the number of pages in shrink_liability
  ubifs: Correctly initialize c->min_log_bytes
  ubifs: Fix double unlock around orphan_delete()
  jffs2: Remove C++ style comments from uapi header

Pull x86 fixes from Thomas Gleixner:
 "A few fixes for x86:

   - Fix a boot regression caused by the recent bootparam sanitizing
     change, which escaped the attention of all people who reviewed that
     code.

   - Address a boot problem on machines with broken E820 tables caused
     by an underflow which ended up placing the trampoline start at
     physical address 0.

   - Handle machines which do not advertise a legacy timer of any form,
     but need calibration of the local APIC timer gracefully by making
     the calibration routine independent from the tick interrupt. Marked
     for stable as well as there seems to be quite some new laptops
     rolled out which expose this.

   - Clear the RDRAND CPUID bit on AMD family 15h and 16h CPUs which are
     affected by broken firmware which does not initialize RDRAND
     correctly after resume. Add a command line parameter to override
     this for machine which either do not use suspend/resume or have a
     fixed BIOS. Unfortunately there is no way to detect this on boot,
     so the only safe decision is to turn it off by default.

   - Prevent RFLAGS from being clobbers in CALL_NOSPEC on 32bit which
     caused fast KVM instruction emulation to break.

   - Explain the Intel CPU model naming convention so that the repeating
     discussions come to an end"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/retpoline: Don't clobber RFLAGS during CALL_NOSPEC on i386
  x86/boot: Fix boot regression caused by bootparam sanitizing
  x86/CPU/AMD: Clear RDRAND CPUID bit on AMD family 15h/16h
  x86/boot/compressed/64: Fix boot on machines with broken E820 table
  x86/apic: Handle missing global clockevent gracefully
  x86/cpu: Explain Intel model naming convention

Pull timekeeping fix from Thomas Gleixner:
 "A single fix for a regression caused by the generic VDSO
  implementation where a math overflow causes CLOCK_BOOTTIME to become a
  random number generator"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping/vsyscall: Prevent math overflow in BOOTTIME update

Pull scheduler fix from Thomas Gleixner:
 "Handle the worker management in situations where a task is scheduled
  out on a PI lock contention correctly and schedule a new worker if
  possible"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Schedule new worker even if PI-blocked

Pull perf fixes from Thomas Gleixner:
 "Two small fixes for kprobes and perf:

   - Prevent a deadlock in kprobe_optimizer() causes by reverse lock
     ordering

   - Fix a comment typo"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  kprobes: Fix potential deadlock in kprobe_optimizer()
  perf/x86: Fix typo in comment

Pull irq fix from Thomas Gleixner:
 "A single fix for a imbalanced kobject operation in the irq decriptor
  code which was unearthed by the new warnings in the kobject code"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Properly pair kobject_del() with kobject_add()

Mergr misc fixes from Andrew Morton:
 "11 fixes"

Mostly VM fixes, one psi polling fix, and one parisc build fix.

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm/kasan: fix false positive invalid-free reports with CONFIG_KASAN_SW_TAGS=y
  mm/zsmalloc.c: fix race condition in zs_destroy_pool
  mm/zsmalloc.c: migration can leave pages in ZS_EMPTY indefinitely
  mm, page_owner: handle THP splits correctly
  userfaultfd_release: always remove uffd flags and clear vm_userfaultfd_ctx
  psi: get poll_work to run when calling poll syscall next time
  mm: memcontrol: flush percpu vmevents before releasing memcg
  mm: memcontrol: flush percpu vmstats before releasing memcg
  parisc: fix compilation errrors
  mm, page_alloc: move_freepages should not examine struct page of reserved memory
  mm/z3fold.c: fix race between migration and destruction

Pull dma-mapping fixes from Christoph Hellwig:
 "Two fixes for regressions in this merge window:

   - select the Kconfig symbols for the noncoherent dma arch helpers on
     arm if swiotlb is selected, not just for LPAE to not break then Xen
     build, that uses swiotlb indirectly through swiotlb-xen

   - fix the page allocator fallback in dma_alloc_contiguous if the CMA
     allocation fails"

* tag 'dma-mapping-5.3-5' of git://git.infradead.org/users/hch/dma-mapping:
  dma-direct: fix zone selection after an unaddressable CMA allocation
  arm: select the dma-noncoherent symbols for all swiotlb builds

The code like this:

	ptr = kmalloc(size, GFP_KERNEL);
	page = virt_to_page(ptr);
	offset = offset_in_page(ptr);
	kfree(page_address(page) + offset);

may produce false-positive invalid-free reports on the kernel with
CONFIG_KASAN_SW_TAGS=y.

In the example above we lose the original tag assigned to 'ptr', so
kfree() gets the pointer with 0xFF tag.  In kfree() we check that 0xFF
tag is different from the tag in shadow hence print false report.

Instead of just comparing tags, do the following:

1) Check that shadow doesn't contain KASAN_TAG_INVALID.  Otherwise it's
   double-free and it doesn't matter what tag the pointer have.

2) If pointer tag is different from 0xFF, make sure that tag in the
   shadow is the same as in the pointer.

Link: http://lkml.kernel.org/r/20190819172540.19581-1-aryabinin@virtuozzo.com
Fixes: 7f94ffbc ("kasan: add hooks implementation for tag-based mode")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: Walter Wu <walter-zh.wu@mediatek.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In zs_destroy_pool() we call flush_work(&pool->free_work).  However, we
have no guarantee that migration isn't happening in the background at
that time.

Since migration can't directly free pages, it relies on free_work being
scheduled to free the pages.  But there's nothing preventing an
in-progress migrate from queuing the work *after*
zs_unregister_migration() has called flush_work().  Which would mean
pages still pointing at the inode when we free it.

Since we know at destroy time all objects should be free, no new
migrations can come in (since zs_page_isolate() fails for fully-free
zspages).  This means it is sufficient to track a "# isolated zspages"
count by class, and have the destroy logic ensure all such pages have
drained before proceeding.  Keeping that state under the class spinlock
keeps the logic straightforward.

In this case a memory leak could lead to an eventual crash if compaction
hits the leaked page.  This crash would only occur if people are
changing their zswap backend at runtime (which eventually starts
destruction).

Link: http://lkml.kernel.org/r/20190809181751.219326-2-henryburns@google.com
Fixes: 48b4800a ("zsmalloc: page migration support")
Signed-off-by: Henry Burns <henryburns@google.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Henry Burns <henrywolfeburns@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Jonathan Adams <jwadams@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>