Add functionality for base-freq info|enable|disable info on CascadeLake-N.

Sample output:
Intel(R) Speed Select Technology
Executing on CPU model:85[0x55]
 package-0
  die-0
    cpu-0
      speed-select-base-freq
        high-priority-base-frequency(MHz):2700000
        high-priority-cpu-mask:00000000,0000e8c0
        high-priority-cpu-list:6,7,11,13,14,15
        low-priority-base-frequency(MHz):2100000
 package-1
  die-0
    cpu-20
      speed-select-base-freq
        high-priority-base-frequency(MHz):2700000
        high-priority-cpu-mask:0000000e,8c000000
        high-priority-cpu-list:26,27,31,33,34,35
        low-priority-base-frequency(MHz):2100000

The enable command always returns success, and the disable command always
returns failed because SST-BF cannot be enabled or disabled from the OS on
CascadeLake-N.

Enable command also have support for --auto|-a option, which sets cpufreq
scaling_min to max, so that the high priority base frequency can be the
required minimum for high priority cores. Disable command with -a/--auto
option reset the setting back to the min frequency.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Add functionality for "perf-profile info" on CascadeLake-N.

Sample output:
intel-speed-select perf-profile info
Intel(R) Speed Select Technology
Executing on CPU model:85[0x55]
 package-0
  die-0
    cpu-0
      perf-profile-level-0
        cpu-count:20
        enable-cpu-mask:00000000,000fffff
        enable-cpu-list:0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19
        thermal-design-power-ratio:23
        base-frequency(MHz):2300
        speed-select-turbo-freq:unsupported
        speed-select-base-freq:enabled
        speed-select-base-freq
          high-priority-base-frequency(MHz):2700000
          high-priority-cpu-mask:00000000,0000e8c0
          high-priority-cpu-list:6,7,11,13,14,15
          low-priority-base-frequency(MHz):2100000
 package-1
  die-0
    cpu-20
      perf-profile-level-0
        cpu-count:20
        enable-cpu-mask:000000ff,fff00000
        enable-cpu-list:20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39
        thermal-design-power-ratio:23
        base-frequency(MHz):2300
        speed-select-turbo-freq:unsupported
        speed-select-base-freq:enabled
        speed-select-base-freq
          high-priority-base-frequency(MHz):2700000
          high-priority-cpu-mask:0000000e,8c000000
          high-priority-cpu-list:26,27,31,33,34,35
          low-priority-base-frequency(MHz):2100000
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

CascadeLake-N only supports SST-BF and needs some of the perf-profile
commands, and the base-freq commands.

Add help functions, and create an empty command structures (the functions
will be implemented later in this patchset).  Call these functions
when running on CascadeLake-N.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Three CascadeLake-N models (6252N, 6230N, and 5218N) have SST-PBF support.

Return an error if the CascadeLake processor is not one of these specific
models.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Make the process_command take any help command and command list.  This
will make it easier to help commands and a command list for CascadeLake-N.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

The current code structure has similar but separate command functions for
the enable and disable operations.  This can be improved by adding an int
argument to the command function structure, and interpreting 1 as enable
and 0 as disable.  This change results in the removal of the disable
command functions.

Add int argument to the command function structure.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

The turbo-freq feature is dependent on the core-power feature. If the
core-power feature is disabled while the turbo-freq feature is enabled,
this will break the turbo-freq feature. This is a firmware limitation,
where they can't return error under this scenario.

So when trying to disable core-power, make sure that the turbo-freq
feature is not enabled. If it enabled, return error if user is trying to
disable the core-power feature.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Introduce --auto|-a option to turbo-freq enable feature, so that it
does in one step for users who are OK by setting all passed target cores
as high priority and set in CLOS 0 and remaining in CLOS 3. In this way,
users don't have to take multiple steps to enable turbo-freq feature. For
users who want more fine grain control, they can always use core-power
feature to set custom CLOS configuration and assignment.

While here also print the error to output when clos configuration fails.

For example
intel-speed-select -c 0-4 turbo-freq enable --auto

The above command will enable turbo-freq and core-power feature. Also
mark CPU 0 to CPU 4 as high priority.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Introduce --auto|-a option to base-freq enable feature, so that it
does in one step for users who are OK by setting all cores with higher
base frequency to be set in CLOS 0 and remaining in CLOS 3. This option
also sets corresponding clos.min to CLOS 0 and CLOS3. In this way, users
don't have to take multiple steps to enable base-freq feature. For users
who want more fine grain control, they can always use core-power feature
to set custom CLOS configuration and assignment.

Also adjust cpufreq/scaling_min_freq for higher and lower priority cores.

For example user can use:
intel-speed-select base-freq enable --auto
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Fix warning for:
isst-config.c: In function ‘set_cpu_online_offline’:
isst-config.c:221:3: warning: ignoring return value of ‘write’,
declared with attribute warn_unused_result [-Wunused-result]
   write(fd, "1\n", 2);
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Add System76 ACPI driver, which adds support for Fn-Fx key
combinations, keyboard backlight, and airplane mode LEDs
on System76 laptops running open source firmware.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Cc: platform-driver-x86@vger.kernel.org
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

This was supposed to be precision "%.*s" instead of width "%*s".  It's
possible that this results in printing beyond the end of the string.

Fixes: a970b95345ab ("platform/x86: huawei-wmi: Add debugfs support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is no need to access global variable directly when we may derive it
through other means.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is no need to keep a pointer to the platform device. Currently there are
no users of it directly, and if there will be in the future we may restore it
from pointer to the struct device.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

We have to clean memory resources allocated during init.

Fixes: 7532afb35012 ("platform/x86: huawei-wmi: Move to platform driver")
Cc: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Fixes: 7532afb35012 ("platform/x86: huawei-wmi: Move to platform driver")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

For APIC case of interrupt we don't fail a ->probe() of the driver,
which makes kernel to print a lot of warnings from the children.

We have two options here:
- switch to platform_get_irq_optional(), though it won't stop children
  to be probed and failed
- fail the ->probe() of i2c-multi-instantiate

Since the in reality we never had devices in the wild where IRQ resource
is optional, the latter solution suits the best.

Fixes: 799d3379 ("platform/x86: i2c-multi-instantiate: Introduce IOAPIC IRQ support")
Reported-by: Ammy Yi <ammy.yi@intel.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>

Since the commit

  7723f4c5 ("driver core: platform: Add an error message to platform_get_irq*()")

the platform_get_irq() started issuing an error message which is not
what we want here.

Switch to platform_get_irq_optional() to have only warning message
provided by the driver.

Fixes: 7723f4c5 ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

This commit adds the bootctl platform driver for Mellanox BlueField
Soc, which queries secure state and controls the eMMC boot partition
swapping by sending SMC calls to ATF running at EL3.

Below are the sequences of typical use case.

  1. User requests boot partition swapping, which could be on-demand or
     during boot-image upgrade via UEFI capsule;

  2. This bootctl driver handles the request and sends SMC call
     to ATF. ATF programs register BREADCRUMB0 which has value
     preserved during warm reset. It also programs eMMC to swap
     the boot partition;

  3. After software reset (rebooting), ATF BL1 (BootRom) checks
     register BREADCRUMB0 and enable watchdog if configured;

  4. If booting fails, the watchdog timer will trigger rebooting.
     In such case, ATF Boot ROM will switch the boot partition
     back to the previous one. This is a robust feature and used
     to prevent failure during boot partition upgrade.
Reviewed-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/platform/x86/classmate-laptop.c: In function cmpc_accel_remove_v4:
drivers/platform/x86/classmate-laptop.c:424:21: warning: variable accel
set but not used [-Wunused-but-set-variable]
drivers/platform/x86/classmate-laptop.c: In function cmpc_accel_remove:
drivers/platform/x86/classmate-laptop.c:660:21: warning: variable accel
set but not used [-Wunused-but-set-variable]

In function cmpc_accel_remove_v4 and cmpc_accel_remove, variable accel is
set but not used, so it can be removed. In that case, variable inputdev is
set but not used and can be removed.

Fixes: 7125587d ("classmate-laptop: Add support for Classmate V4 accelerometer.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Existing intel_cht_int33fe ACPI pseudo-device driver assumes that
hardware has Type-C connector and register related devices described as
I2C connections in the _CRS resource.

There is at least one hardware (Lenovo Yoga Book YB1-91L/F) with Micro-B
USB connector exists. It has INT33FE device in the DSDT table but
there are only two I2C connection described: PMIC and BQ27452 battery
fuel gauge.

Splitting existing INT33FE driver allow to maintain code for USB Micro-B
(or AB) connector variant separately and make it simpler.

Split driver to intel_cht_int33fe_common.c and
intel_cht_int33fe_{microb,typec}.c. Compile all this sources to one .ko
module to make user experience easier.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

The driver does not use polling mode of input devices, and this config
option is going away, so let's not reference it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

We have added polled mode to the normal input devices with the intent of
retiring input_polled_dev. This converts peaq-wmi driver to use the
polling mode of standard input devices and removes dependency on
INPUT_POLLDEV.

Because the new polling coded does not allow peeking inside the poller
structure to get the poll interval, we change the "debounce" process to
operate on the time basis, instead of counting events.

We also fix error handling during initialization, as previously we leaked
input device structure when we failed to register it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

We have added polled mode to the normal input devices with the intent of
retiring input_polled_dev. This converts hdaps driver to use the
polling mode of standard input devices and removes dependency on
INPUT_POLLDEV.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

We have added polled mode to the normal input devices with the intent of
retiring input_polled_dev. This converts Asus laptop driver to use the
polling mode of standard input devices and removes dependency on
INPUT_POLLDEV.

Also removed no longed needed set_bit(EV_ABS, ...) as
input_set_abs_oarams() does it for us.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

This patch adds a quirk disabling keyboard backlight support for the
Dell Inspiron 1012 and 1018.

Those models wrongly report supporting keyboard backlight control
features (through SMBIOS tokens) even though they're not equipped with
a backlit keyboard. This led to broken controls being exposed
through sysfs by this driver which froze the system when used.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=107651Signed-off-by: Pacien TRAN-GIRARD <pacien.trangirard@pacien.net>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Add a debugfs interface that can be used to call the WMI management
interface function if available.
Signed-off-by: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Huawei Matebook laptops uses Fn key and toggle to access F1-F12 keys.
Along with that, there is this feature called fn-lock that inverts the
behavior of this Fn key and the F1-F12 row.
Signed-off-by: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Control battery charge thresholds through the battery API and driver's
attributes.

Setting battery charging thresholds can introduce a race condition with
MACH-WX9 where two or more threads are trying to read/write values
from/to EC memory.
Signed-off-by: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Huawei Matebook laptops come with a WMI management interface that can
control various aspects of the device. This interface is also found on
the old Matebook X released in 2017.

Use that to control the mic mute LED.
Signed-off-by: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Introduce quirks and module parameters. 3 quirks are added:
1. Fixes reporting brightness keys twice since it's already handled by
   acpi-video.
2. Some models need a short delay when setting battery thresholds to
   prevent a race condition when two processes read/write. (will be used later)
3. Matebook X (2017) handles micmute led through the "legacy" interface
   which is not currently implemented. Use ACPI EC method to control
   this led. (will be used later)

2 module parameters are added to enable this short delay and/or report
  brightness keys through this driver.
Signed-off-by: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Move from WMI driver to platform driver. This move is necessary since
the driver is no longer a hotkeys driver only. Platform driver makes it
easier for users to access sysfs attributes under (i.e.
/sys/devices/platform/huawei-wmi) compared to wmi driver.

Use WMI device UID, AMW0 has a UID of HWMI. WMI0 is the device name
and doesn't have a UID so keep it as it is.
Signed-off-by: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Pull tracing fixes from Steven Rostedt:
 "A few tracing fixes:

   - Remove lockdown from tracefs itself and moved it to the trace
     directory. Have the open functions there do the lockdown checks.

   - Fix a few races with opening an instance file and the instance
     being deleted (Discovered during the lockdown updates). Kept
     separate from the clean up code such that they can be backported to
     stable easier.

   - Clean up and consolidated the checks done when opening a trace
     file, as there were multiple checks that need to be done, and it
     did not make sense having them done in each open instance.

   - Fix a regression in the record mcount code.

   - Small hw_lat detector tracer fixes.

   - A trace_pipe read fix due to not initializing trace_seq"

* tag 'trace-v5.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Initialize iter->seq after zeroing in tracing_read_pipe()
  tracing/hwlat: Don't ignore outer-loop duration when calculating max_latency
  tracing/hwlat: Report total time spent in all NMIs during the sample
  recordmcount: Fix nop_mcount() function
  tracing: Do not create tracefs files if tracefs lockdown is in effect
  tracing: Add locked_down checks to the open calls of files created for tracefs
  tracing: Add tracing_check_open_get_tr()
  tracing: Have trace events system open call tracing_open_generic_tr()
  tracing: Get trace_array reference for available_tracers files
  ftrace: Get a reference counter for the trace_array on filter files
  tracefs: Revert ccbd54ff ("tracefs: Restrict tracefs when the kernel is locked down")

Merge tag 'hwmon-for-v5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:

 - Update/fix inspur-ipsps1 and k10temp Documentation

 - Fix nct7904 driver

 - Fix HWMON_P_MIN_ALARM mask in hwmon core

* tag 'hwmon-for-v5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: docs: Extend inspur-ipsps1 title underline
  hwmon: (nct7904) Add array fan_alarm and vsen_alarm to store the alarms in nct7904_data struct.
  docs: hwmon: Include 'inspur-ipsps1.rst' into docs
  hwmon: Fix HWMON_P_MIN_ALARM mask
  hwmon: (k10temp) Update documentation and add temp2_input info
  hwmon: (nct7904) Fix the incorrect value of vsen_mask in nct7904_data struct

Pull MTD fixes from Richard Weinberger:
 "Two fixes for MTD:

   - spi-nor: Fix for a regression in write_sr()

   - rawnand: Regression fix for the au1550nd driver"

* tag 'fixes-for-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
  mtd: rawnand: au1550nd: Fix au_read_buf16() prototype
  mtd: spi-nor: Fix direction of the write_sr() transfer

Pull io_uring fix from Jens Axboe:
 "Single small fix for a regression in the sequence logic for linked
  commands"

* tag 'for-linus-20191012' of git://git.kernel.dk/linux-block:
  io_uring: fix sequence logic for timeout requests

A customer reported the following softlockup:

[899688.160002] NMI watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [test.sh:16464]
[899688.160002] CPU: 0 PID: 16464 Comm: test.sh Not tainted 4.12.14-6.23-azure #1 SLE12-SP4
[899688.160002] RIP: 0010:up_write+0x1a/0x30
[899688.160002] Kernel panic - not syncing: softlockup: hung tasks
[899688.160002] RIP: 0010:up_write+0x1a/0x30
[899688.160002] RSP: 0018:ffffa86784d4fde8 EFLAGS: 00000257 ORIG_RAX: ffffffffffffff12
[899688.160002] RAX: ffffffff970fea00 RBX: 0000000000000001 RCX: 0000000000000000
[899688.160002] RDX: ffffffff00000001 RSI: 0000000000000080 RDI: ffffffff970fea00
[899688.160002] RBP: ffffffffffffffff R08: ffffffffffffffff R09: 0000000000000000
[899688.160002] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8b59014720d8
[899688.160002] R13: ffff8b59014720c0 R14: ffff8b5901471090 R15: ffff8b5901470000
[899688.160002]  tracing_read_pipe+0x336/0x3c0
[899688.160002]  __vfs_read+0x26/0x140
[899688.160002]  vfs_read+0x87/0x130
[899688.160002]  SyS_read+0x42/0x90
[899688.160002]  do_syscall_64+0x74/0x160

It caught the process in the middle of trace_access_unlock(). There is
no loop. So, it must be looping in the caller tracing_read_pipe()
via the "waitagain" label.

Crashdump analyze uncovered that iter->seq was completely zeroed
at this point, including iter->seq.seq.size. It means that
print_trace_line() was never able to print anything and
there was no forward progress.

The culprit seems to be in the code:

	/* reset all but tr, trace, and overruns */
	memset(&iter->seq, 0,
	       sizeof(struct trace_iterator) -
	       offsetof(struct trace_iterator, seq));

It was added by the commit 53d0aa77 ("ftrace:
add logic to record overruns"). It was v2.6.27-rc1.
It was the time when iter->seq looked like:

     struct trace_seq {
	unsigned char		buffer[PAGE_SIZE];
	unsigned int		len;
     };

There was no "size" variable and zeroing was perfectly fine.

The solution is to reinitialize the structure after or without
zeroing.

Link: http://lkml.kernel.org/r/20191011142134.11997-1-pmladek@suse.comSigned-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

max_latency is intended to record the maximum ever observed hardware
latency, which may occur in either part of the loop (inner/outer). So
we need to also consider the outer-loop sample when updating
max_latency.

Link: http://lkml.kernel.org/r/157073345463.17189.18124025522664682811.stgit@srivatsa-ubuntu

Fixes: e7c15cd8 ("tracing: Added hardware latency tracer")
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

nmi_total_ts is supposed to record the total time spent in *all* NMIs
that occur on the given CPU during the (active portion of the)
sampling window. However, the code seems to be overwriting this
variable for each NMI, thereby only recording the time spent in the
most recent NMI. Fix it by accumulating the duration instead.

Link: http://lkml.kernel.org/r/157073343544.17189.13911783866738671133.stgit@srivatsa-ubuntu

Fixes: 7b2c8625 ("tracing: Add NMI tracing in hwlat detector")
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>