GPIOs can be also used on bcm53xx, however this arch requires different
implementation of IRQ support. It uses different IRQ number (117) and
different masks & acking.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch makes the driver to report signal strength information
to mac80211 for rtl8187se boards.

It differs from my previous RFT patch:
http://marc.info/?l=linux-wireless&m=140155388332534&w=2
because:
- I have now a working rtl8187se card, so I could serve my RFT by myself. :)
- CCK measurement code has changed a bit, but it does basically the same things.
- OFDM measurement method is changed because the older method reported incorrect
  measures, at least for signals stronger than -40dBm).

CCK measurement seems quite good. OFDM seems less accurate, but this is the
same as the "reference" staging driver dose. I wanted not to change things just
to make measures of _one_ (my) card a bit more close to what _I_ (in my setup)
expected..

IMHO results are still good enough to justify reporting signal in dBm rather than in
"unspecified" units, so this is what this patch actually does.

Results of my tests with a working rtl8187se card connected with coaxes and
various RF attenuators to my AP are:

Input (approx) | CCK meas | OFDM meas
--------------------------------------
      -30dBm   |  -32dBm  |  -31dBm
      -40dBm   |  -40dBm  |  -41dBm
      -50dBm   |  -50dBm  |  -55dBm
      -60dBm   |  -59dBm  |  -63dBm
      -70dBm   |  -69dBm  |  -73dBm
      -80dBm   |  -79dBm  |  -83dBm

Also some real-field tests has been done (no coax, packets in the air) for the CCK
measure method, and they resulted in reasonable values.

Thanks-to: Bernhard Schiffner <bernhard@schiffner-limbach.de> [ for real-field tests]
Signed-off-by: andrea.merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When multiple channel contexts are enabled, a p2p interface
that is assigned to a context will have an address that
is different from the device mac address, which is used
by wpa_s as the p2p device ID.

Certain frames like provision requests use the device address
and these get dropped since ath9k_calculate_summary_state()
iterates over only the active interfaces in a context and the
device address is not used.

Fix this by adding the device mac address to the bssid mask.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some chip IDs are easier to read/understand when printed in a decimal
form. For example on my bcm53xx arch router this patch replaces:
Found chip with id 0xCF12, rev 0x00 and package 0x02
with a:
Found chip with id 53010, rev 0x00 and package 0x02
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Check for scan channel gap only when user_scan_in is not NULL.
user_scan_in is NULL for internal scans and if we check scan channel gap
at this place, it may result into crash.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using the BSS information stored in mac80211 directly
is racy in certain conditions. For example, in a MCC
setup, if the scheduler is switching channels when
a local deauth is issued, calculation of the opmode/bssid
etc. is incorrect. To avoid this, store the bss params
in the driver and use it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

AHB bus support was added in v2.6.38, through commit a0b907ee
("ath5k: Add AHB bus support."). That code can only be build if the
Kconfig symbol ATHEROS_AR231X is set. But that symbol has never been
added to the tree. So AHB bus support has always been dead code.

Let's remove all code that depends on ATHEROS_AR231X. If that symbol
ever gets added to the tree the AHB bus support can be re-added too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Samuel Ortiz <sameo@linux.intel.com> says:

"NFC: 3.18 pull request

This is the NFC pull request for 3.18.

We've had major updates for TI and ST Microelectronics drivers:

For TI's trf7970a driver:

- Target mode support for trf7970a
- Suspend/resume support for trf7970a
- DT properties additions to handle different quirks
- A bunch of fixes for smartphone IOP related issues

For ST Microelectronics' ST21NFCA and ST21NFCB drivers:

- ISO15693 support for st21nfcb
- checkpatch and sparse related warning fixes
- Code cleanups and a few minor fixes

Finally, Marvell add ISO15693 support to the NCI stack, together with a
couple of NCI fixes."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The sco_param_wideband table represents the eSCO parameters for
specifically mSBC encoding. This patch renames the table to the more
descriptive esco_param_msbc name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

It is expected that new parameter combinations will have the
retransmission effort value different between some entries (mainly
because of the new S4 configuration added by HFP 1.7), so it makes sense
to move it into the table instead of having it hard coded based on the
selected SCO_AIRMODE_*.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The 6lowpan ipv6 header compression was causing problems for other interfaces
that expected a ipv6 header to still be in place, as we were replacing the
ipv6 header with a compressed version. This happened if you sent a packet to a
multicast address as the packet would be output on 802.15.4, ethernet, and also
be sent to the loopback interface. The skb data was shared between these
interfaces so all interfaces ended up with a compressed ipv6 header.

The solution is to ensure that before we do any header compression we are not
sharing the skb or skb data with any other interface. If we are then we must
take a copy of the skb and skb data before modifying the ipv6 header.
The only place we can copy the skb is inside the xmit function so we don't
leave dangling references to skb.

This patch moves all the header compression to inside the xmit function. Very
little code has been changed it has mostly been moved from lowpan_header_create
to lowpan_xmit. At the top of the xmit function we now check if the skb is
shared and if so copy it. In lowpan_header_create all we do now is store the
source and destination addresses for use later when we compress the header.
Signed-off-by: Simon Vincent <simon.vincent@xsilon.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Replace printk() with dev_*() pr_*().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Remove the return statement in the void function.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The core specification defines valid values for the
HCI_Reject_Synchronous_Connection_Request command to be 0x0D-0x0F. So
far the code has been using HCI_ERROR_REMOTE_USER_TERM (0x13) which is
not a valid value and is therefore being rejected by some controllers:

 > HCI Event: Connect Request (0x04) plen 10
	bdaddr 40:6F:2A:6A:E5:E0 class 0x000000 type eSCO
 < HCI Command: Reject Synchronous Connection (0x01|0x002a) plen 7
	bdaddr 40:6F:2A:6A:E5:E0 reason 0x13
	Reason: Remote User Terminated Connection
 > HCI Event: Command Status (0x0f) plen 4
	Reject Synchronous Connection (0x01|0x002a) status 0x12 ncmd 1
	Error: Invalid HCI Command Parameters

This patch introduces a new define for a value from the valid range
(0x0d == Connection Rejected Due To Limited Resources) and uses it
instead for rejecting incoming connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

No caller or macro uses the return value so make all
the functions return void.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

skb is already freed in st21nfca_tx_work and was freed also in
st21nfca_im_send_psl_req.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

"skb" can be NULL here but it can't be an ERR_PTR:
- IS_ERR(NULL) return false and skb migth be NULL.
- skb cannot be a ERR_PTR as nfc_hci_send_cmd_async it never using such cast.

!skb is more appropriate at those places.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

In case we are not able to read out the NDLC/NCI header, we do not
consider this as an issue and we will give a later chance.
The NDLC layer will handle errors thanks to its internal timers.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add support for ISO/IEC 15693 RF technology and Type 5 tags.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

In NFC Forum NCI specification, some RF Protocol values are
reserved for proprietary use (from 0x80 to 0xfe).
Some CLF vendor may need to use one value within this range
for specific technology.
Furthermore, some CLF may not becompliant with NFC Froum NCI
specification 2.0 and therefore will not support RF Protocol
value 0x06 for PROTOCOL_T5T as mention in a draft specification
and in a recent push.

Adding get_rf_protocol handle to the nci_ops structure will
help to set the correct technology to target.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

T2 was never started when sending a command.
Start it when sending a command for the first attempt
and stop it once we receive the answer.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

On st21nfcb the irq line might be kept to active state because of other
interfaces activity. This may generate i2c read tentative resulting in
i2c NACK.

This fix will currently let NDLC upper layer to decide when it is relevent
to signal to the physical layer when the chip as muted.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

St21nfcb has a reverse polarity compare to st21nfca.
In st21nfcb case, the irq pin is active high.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch fix a previous patch introduce by commit	0a91e8ac

It is actually fixing a double free mistake in all st21nfca_tm_* function.
We decide to return directly in case of successful execution because skb
got already freed. In st21nfca_tm_recv_dep_req it got freed by nfc_tm_data_received.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

After a unsuccessful call to nfc_hci_send_event the skb was not
freed and might lead to memory leak.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Fix few conding style issue such as useless line return or tab.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The recently added _trf7970a_tg_listen() routine
has some return paths that don't unlock the mutex
that is locked when the routine is entered.  Fix
this by always unlocking the mutex before returning.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Recent changes to trf7970a_irq() added a couple return
paths that don't unlock the mutex that is locked when
the routine is entered.  Fix this by ensuring the mutex
is always unlocked before returning.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

There is no need to initialize the 'ret' variable
in trf7970a_resume().
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The trf7970a_suspend() routine always returns
zero so don't use a local return variable to
hold the return value.  This fixes up a smatch
warning.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

SCO connection cannot be setup to devices that do not support retransmission.
Patch based on http://permalink.gmane.org/gmane.linux.bluez.kernel/7779 and
adapted for this kernel version.

Code changed to check SCO/eSCO type before setting retransmission effort
and max. latency. The purpose of the patch is to support older devices not
capable of eSCO.

Tested on Blackberry 655+ headset which does not support retransmission.
Credits go to Alexander Sommerhuber.
Signed-off-by: Bernhard Thaler <bernhard.thaler@r-it.at>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Move iwl_mvm_max_scan_ie_len function to scan.c and fix the
implementation to conform with the LMAC scan API.
Since the correct implementation would leave us with unacceptably
tiny probes, add a workaround which returns a larger value.
In current implementation it's possible that unified_scan_lmac and
unified_sched_scan_lmac would return -ENOBUFS.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The tables still contain dummy values.

Cc: <stable@vger.kernel.org> [3.15+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In case of traffic on multiple TIDs where one is aggregated
and the other is not RS would toggle between considering
traffic vs. the station as aggregated and not aggregated.
Instead consider the sta state as aggregated as long as
there's at least one TID aggregated.
This limitation is because the rates table is kept per
station and not per TID.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently BA notifications which don't reclaim any frames
would not cause the RS to be called as no skbs are passed
to mac80211. This is not optimal as RS can benefit from the
statistics of sent vs. acked of such a BA. This can improve the
reaction time of the RS algorithm. Also, an upcoming change in
the firmware would cause BA timeout to be reported as a BA notif
with 0 acked so this change is required for that as well.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The 8000 HW series also includes the revision in the FW
name.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>