This fixes compilation warnings:

drivers/net/fddi/defxx.c:294: warning: 'dfx_rcv_flush' declared inline after being called
drivers/net/fddi/defxx.c:294: warning: previous declaration of 'dfx_rcv_flush' was here
drivers/net/fddi/defxx.c:2854: warning: 'my_skb_align' defined but not used

triggered when the driver is built with DYNAMIC_BUFFERS undefined.  Code
tested to work just fine with these changes and a few DEFPA and DEFTA
boards.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RX handler of the driver has two paths switched between, depending on
the size of the frame received, as determined by SKBUFF_RX_COPYBREAK.

When a small frame is received, a new skb allocated has data space large
enough to hold the incoming frame only, and data is copied there from the
original skb whose buffer is returned to the DMA RX ring; in that case
`rx_in_place' is 0.  When a large frame is received, a new skb allocated
has data space large enough to hold the largest frame possible, including
the overhead for alignment, the receive status and padding, over 4.5kiB
overall, and its buffer is placed on the DMA RX ring while the original
buffer is passed up to the network stack avoiding the need to copy data;
in that case `rx_in_place' is 1.

However the latter scenario is only possible when dynamic buffers are
used, as determined by DYNAMIC_BUFFERS, because otherwise the buffers used
for the DMA RX ring are fixed at the time the interface is brought up.

That leads to an observation that the preprocessor conditional around the
`rx_in_place' check is inverted, the check only really matters when
dynamic buffers are in use.  It has gone unnoticed for many years since
support for using dynamic buffers on the DMA RX ring was introduced in
2.1.40 -- because the only problem that results is in the case where
`rx_in_place' is 1 frame data received is unnecessarily copied to the
newly-allocated buffer, before the buffer placed on the the DMA receive RX
and its contents ignored.  Therefore the only symptom is some performance
loss.

Rather than flipping the condition though I decided to discard the
conditional altogether -- in the case of static buffers `rx_in_place' is
always 0 so GCC will optimise the C conditional away instead.

Tested on a few DEFPA and DEFTA boards successfully using both small and
large frames, both with DYNAMIC_BUFFERS defined and with the macro
undefined.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When in repair-mode and TCP_RECV_QUEUE is set, we end up calling
tcp_push with mss_now being 0. If data is in the send-queue and
tcp_set_skb_tso_segs gets called, we crash because it will divide by
mss_now:

[  347.151939] divide error: 0000 [#1] SMP
[  347.152907] Modules linked in:
[  347.152907] CPU: 1 PID: 1123 Comm: packetdrill Not tainted 3.16.0-rc2 #4
[  347.152907] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[  347.152907] task: f5b88540 ti: f3c82000 task.ti: f3c82000
[  347.152907] EIP: 0060:[<c1601359>] EFLAGS: 00210246 CPU: 1
[  347.152907] EIP is at tcp_set_skb_tso_segs+0x49/0xa0
[  347.152907] EAX: 00000b67 EBX: f5acd080 ECX: 00000000 EDX: 00000000
[  347.152907] ESI: f5a28f40 EDI: f3c88f00 EBP: f3c83d10 ESP: f3c83d00
[  347.152907]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[  347.152907] CR0: 80050033 CR2: 083158b0 CR3: 35146000 CR4: 000006b0
[  347.152907] Stack:
[  347.152907]  c167f9d9 f5acd080 000005b4 00000002 f3c83d20 c16013e6 f3c88f00 f5acd080
[  347.152907]  f3c83da0 c1603b5a f3c83d38 c10a0188 00000000 00000000 f3c83d84 c10acc85
[  347.152907]  c1ad5ec0 00000000 00000000 c1ad679c 010003e0 00000000 00000000 f3c88fc8
[  347.152907] Call Trace:
[  347.152907]  [<c167f9d9>] ? apic_timer_interrupt+0x2d/0x34
[  347.152907]  [<c16013e6>] tcp_init_tso_segs+0x36/0x50
[  347.152907]  [<c1603b5a>] tcp_write_xmit+0x7a/0xbf0
[  347.152907]  [<c10a0188>] ? up+0x28/0x40
[  347.152907]  [<c10acc85>] ? console_unlock+0x295/0x480
[  347.152907]  [<c10ad24f>] ? vprintk_emit+0x1ef/0x4b0
[  347.152907]  [<c1605716>] __tcp_push_pending_frames+0x36/0xd0
[  347.152907]  [<c15f4860>] tcp_push+0xf0/0x120
[  347.152907]  [<c15f7641>] tcp_sendmsg+0xf1/0xbf0
[  347.152907]  [<c116d920>] ? kmem_cache_free+0xf0/0x120
[  347.152907]  [<c106a682>] ? __sigqueue_free+0x32/0x40
[  347.152907]  [<c106a682>] ? __sigqueue_free+0x32/0x40
[  347.152907]  [<c114f0f0>] ? do_wp_page+0x3e0/0x850
[  347.152907]  [<c161c36a>] inet_sendmsg+0x4a/0xb0
[  347.152907]  [<c1150269>] ? handle_mm_fault+0x709/0xfb0
[  347.152907]  [<c15a006b>] sock_aio_write+0xbb/0xd0
[  347.152907]  [<c1180b79>] do_sync_write+0x69/0xa0
[  347.152907]  [<c1181023>] vfs_write+0x123/0x160
[  347.152907]  [<c1181d55>] SyS_write+0x55/0xb0
[  347.152907]  [<c167f0d8>] sysenter_do_call+0x12/0x28

This can easily be reproduced with the following packetdrill-script (the
"magic" with netem, sk_pacing and limit_output_bytes is done to prevent
the kernel from pushing all segments, because hitting the limit without
doing this is not so easy with packetdrill):

0   socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0  setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0

+0  bind(3, ..., ...) = 0
+0  listen(3, 1) = 0

+0  < S 0:0(0) win 32792 <mss 1460>
+0  > S. 0:0(0) ack 1 <mss 1460>
+0.1  < . 1:1(0) ack 1 win 65000

+0  accept(3, ..., ...) = 4

// This forces that not all segments of the snd-queue will be pushed
+0 `tc qdisc add dev tun0 root netem delay 10ms`
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=2`
+0 setsockopt(4, SOL_SOCKET, 47, [2], 4) = 0

+0 write(4,...,10000) = 10000
+0 write(4,...,10000) = 10000

// Set tcp-repair stuff, particularly TCP_RECV_QUEUE
+0 setsockopt(4, SOL_TCP, 19, [1], 4) = 0
+0 setsockopt(4, SOL_TCP, 20, [1], 4) = 0

// This now will make the write push the remaining segments
+0 setsockopt(4, SOL_SOCKET, 47, [20000], 4) = 0
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=130000`

// Now we will crash
+0 write(4,...,1000) = 1000

This happens since ec342325 (tcp: fix retransmission in repair
mode). Prior to that, the call to tcp_push was prevented by a check for
tp->repair.

The patch fixes it, by adding the new goto-label out_nopush. When exiting
tcp_sendmsg and a push is not required, which is the case for tp->repair,
we go to this label.

When repairing and calling send() with TCP_RECV_QUEUE, the data is
actually put in the receive-queue. So, no push is required because no
data has been added to the send-queue.

Cc: Andrew Vagin <avagin@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Fixes: ec342325 (tcp: fix retransmission in repair mode)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Acked-by: Andrew Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk_dst_cache has __rcu annotation, so we need a cast to avoid
following sparse error :

include/net/sock.h:1774:19: warning: incorrect type in initializer (different address spaces)
include/net/sock.h:1774:19:    expected struct dst_entry [noderef] <asn:4>*__ret
include/net/sock.h:1774:19:    got struct dst_entry *dst
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 7f502361 ("ipv4: irq safe sk_dst_[re]set() and ipv4_sk_update_pmtu() fix")
Signed-off-by: David S. Miller <davem@davemloft.net>

Madalin-Cristian reported crashs happening after a recent commit
(5a4ae5f6 "vlan: unnecessary to check if vlan_pcpu_stats is NULL")

-----------------------------------------------------------------------
root@p5040ds:~# vconfig add eth8 1
root@p5040ds:~# vconfig rem eth8.1
Unable to handle kernel paging request for data at address 0x2bc88028
Faulting instruction address: 0xc058e950
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=8 CoreNet Generic
Modules linked in:
CPU: 3 PID: 2167 Comm: vconfig Tainted: G        W     3.16.0-rc3-00346-g65e85bf #2
task: e7264d90 ti: e2c2c000 task.ti: e2c2c000
NIP: c058e950 LR: c058ea30 CTR: c058e900
REGS: e2c2db20 TRAP: 0300   Tainted: G        W      (3.16.0-rc3-00346-g65e85bf)
MSR: 00029002 <CE,EE,ME>  CR: 48000428  XER: 20000000
DEAR: 2bc88028 ESR: 00000000
GPR00: c047299c e2c2dbd0 e7264d90 00000000 2bc88000 00000000 ffffffff 00000000
GPR08: 0000000f 00000000 000000ff 00000000 28000422 10121928 10100000 10100000
GPR16: 10100000 00000000 c07c5968 00000000 00000000 00000000 e2c2dc48 e7838000
GPR24: c07c5bac c07c58a8 e77290cc c07b0000 00000000 c05de6c0 e7838000 e2c2dc48
NIP [c058e950] vlan_dev_get_stats64+0x50/0x170
LR [c058ea30] vlan_dev_get_stats64+0x130/0x170
Call Trace:
[e2c2dbd0] [ffffffea] 0xffffffea (unreliable)
[e2c2dc20] [c047299c] dev_get_stats+0x4c/0x140
[e2c2dc40] [c0488ca8] rtnl_fill_ifinfo+0x3d8/0x960
[e2c2dd70] [c0489f4c] rtmsg_ifinfo+0x6c/0x110
[e2c2dd90] [c04731d4] rollback_registered_many+0x344/0x3b0
[e2c2ddd0] [c047332c] rollback_registered+0x2c/0x50
[e2c2ddf0] [c0476058] unregister_netdevice_queue+0x78/0xf0
[e2c2de00] [c058d800] unregister_vlan_dev+0xc0/0x160
[e2c2de20] [c058e360] vlan_ioctl_handler+0x1c0/0x550
[e2c2de90] [c045d11c] sock_ioctl+0x28c/0x2f0
[e2c2deb0] [c010d070] do_vfs_ioctl+0x90/0x7b0
[e2c2df20] [c010d7d0] SyS_ioctl+0x40/0x80
[e2c2df40] [c000f924] ret_from_syscall+0x0/0x3c

Fix this problem by freeing percpu stats from dev->destructor() instead
of ndo_uninit()
Reported-by: Madalin-Cristian Bucur <madalin.bucur@freescale.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Madalin-Cristian Bucur <madalin.bucur@freescale.com>
Fixes: 5a4ae5f6 ("vlan: unnecessary to check if vlan_pcpu_stats is NULL")
Cc: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 86f6cf41 (net: of_mdio: add of_mdiobus_link_phydev()) introduced a
circular dependency between libphy and of_mdio.

depmod: ERROR: <modroot>/kernel/drivers/net/phy/libphy.ko in
dependency cycle!
depmod: ERROR: <modroot>/kernel/drivers/of/of_mdio.ko in dependency cycle!

The problem is that of_mdio.c references &mdio_bus_type and libphy now
references of_mdiobus_link_phydev.

Fix this by not exporting of_mdiobus_link_phydev() from of_mdio.ko.
Make it a static function in mdio_bus.c instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Jeff Mahoney <jeffm@suse.com>
Fixes: 86f6cf41 (net: of_mdio: add of_mdiobus_link_phydev())
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
pull request: wireless 2014-06-27

Please pull the following batch of fixes for the 3.16 stream...

For the mac80211 bits, Johannes says:

"We have a fix from Eliad for a time calculation, a fix from Max for
head/tailroom when sending authentication packets, a revert that Felix
requested since the patch in question broke regulatory and a fix from
myself for an issue with a new command that we advertised in the wrong
place."

For the bluetooth bits, Gustavo says:

"A few fixes for 3.16. This pull request contains a NULL dereference fix,
and some security/pairing fixes."

For the iwlwifi bits, Emmanuel says:

"I have here a fix from Eliad for scheduled scan: it fixes a firmware
assertion. Arik reverts a patch I made that didn't take into account
that 3160 doesn't have UAPSD and hence, we can't assume that all
newer firmwares support the feature. Here too, the visible effect
is a firmware assertion. Along with that, we have a few fixes and
additions to the device list."

For the ath10k bits, Kalle says:

"Bartosz fixed an issue where we were not able to create 8 vdevs when
using DFS. Michal removed a false warning which was just confusing
people."

On top of that...

Arend van Spriel fixes a 'divide by zero' regression in brcmfmac.

Amitkumar Karwar corrects a transmit timeout in mwifiex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Hardware will provide this information as soon as we will start
processing incoming packets, so there is no need to set the RX buffer
length during buffer allocation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We use the PHY library which will determine the link state for us, make
sure we start with a carrier off until libphy has completed the link
training.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As soon as register_netdev() is called, the network device notifiers are
running which means that other parts of the kernel, or user-space
programs can call the network device ndo_open() callback and use the
interface.

Disable the Ethernet device clock before we register the network device
such that we do not create the following situation:

CPU0				CPU1
register_netdev()
				bcmgenet_open()
				clk_prepare_enable()
clk_disable_unprepare()

and leave the hardware block gated off, while we think it should be
gated on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Although we do not limit the number of packets the TX completion
function bcm_sysport_tx_reclaim() is allowed to reclaim, we were still
using its return value as-is. This means that we could hit the WARN() in
net/core/dev.c where work_done >= budget.

Make sure we do exit the NAPI context when the TX ring is empty, and
pretend there was no work to do.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The UniMAC CMD_SW_RESET bit is not a self-clearing bit, so we need to
assert it, wait a bit and clear it manually. As a result, umac_reset()
is updated not to return any value. The previous version of the code
simply wrote 0 to the CMD register, which would make the busy-waiting
loop exit immediately, having zero effect.

By writing 0 to the CMD register, we were clearing all bits in the CMD
register, and not using the hardware reset default values which are
set on purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SYSTEMPORT Ethernet MAC supports multicast just fine, it just lacks
any sort of Unicast/Broadcast/Multicasting filtering at the Ethernet MAC
level since that is handled by the front end Ethernet switch, but that
is properly handled by bcm_sysport_set_rx_mode().

Some user-space applications might be relying on the presence of this
flag to prevent using multicast sockets, this also prevents that
interface from joining the IPv6 all-router mcast group.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While it is legal to kfree(NULL), it is not wise to use :
put_page(virt_to_head_page(NULL))

 BUG: unable to handle kernel paging request at ffffeba400000000
 IP: [<ffffffffc01f5928>] virt_to_head_page+0x36/0x44 [bnx2x]
Reported-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Fixes: d46d132c ("bnx2x: use netdev_alloc_frag()")
Signed-off-by: David S. Miller <davem@davemloft.net>

We have two different ways to handle changes to sk->sk_dst

First way (used by TCP) assumes socket lock is owned by caller, and use
no extra lock : __sk_dst_set() & __sk_dst_reset()

Another way (used by UDP) uses sk_dst_lock because socket lock is not
always taken. Note that sk_dst_lock is not softirq safe.

These ways are not inter changeable for a given socket type.

ipv4_sk_update_pmtu(), added in linux-3.8, added a race, as it used
the socket lock as synchronization, but users might be UDP sockets.

Instead of converting sk_dst_lock to a softirq safe version, use xchg()
as we did for sk_rx_dst in commit e47eb5df ("udp: ipv4: do not use
sk_dst_lock from softirq context")

In a follow up patch, we probably can remove sk_dst_lock, as it is
only used in IPv6.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Fixes: 9cb3a50c ("ipv4: Invalidate the socket cached route on pmtu events if possible")
Signed-off-by: David S. Miller <davem@davemloft.net>

We have to return the boolean here if the tag presents
or not, not just ANDing the TCI with the mask which results to:

[  709.412097] test_bpf: #18 LD_VLAN_TAG_PRESENT
[  709.412245] ret 4096 != 1
[  709.412332] ret 4096 != 1
[  709.412333] FAIL (2 times)
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

To get a full tag (and not just a VID) we should access the TCI
except the VLAN_TAG_PRESENT field (which means that 802.1q header
is present). Also ensure that the VLAN_TAG_PRESENT stay on its place
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

Based on RFC3810 6.2, we also need to check the hop limit and router alert
option besides source address.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add MIB counters for rcvbuferrors in UDP to help diagnose problems.
Signed-off-by: James M Leddy <james.leddy@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MSI-X should use PCI_MSIX_FLAGS not PCI_MSI_FLAGS.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull CIFS fixes from Steve French:
 "Small set of misc cifs/smb3 fixes"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  [CIFS] fix mount failure with broken pathnames when smb3 mount with mapchars option
  cifs: revalidate mapping prior to satisfying read_iter request with cache=loose
  fs/cifs: fix regression in cifs_create_mf_symlink()

Pull hwmon fixes from Guenter Roeck:
 "Various minor fixes"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (gpio-fan) Change name used in hwmon_device_register_with_groups
  hwmon: (emc1403) Fix missing 'select REGMAP_I2C' in Kconfig
  hwmon: (ntc_thermistor) Use the manufacturer name properly
  devicetree: bindings: Document murata vendor prefix
  hwmon: (w83l786ng) Report correct minimum fan speed

Pull networking fixes from David Miller:

 1) Fix crash in ipvs tot_stats estimator, from Julian Anastasov.

 2) Fix OOPS in nf_nat on netns removal, from Florian Westphal.

 3) Really really really fix locking issues in slip and slcan tty write
    wakeups, from Tyler Hall.

 4) Fix checksum offloading in fec driver, from Fugang Duan.

 5) Off by one in BPF instruction limit test, from Kees Cook.

 6) Need to clear all TSO capability flags when doing software TSO in
    tg3 driver, from Prashant Sreedharan.

 7) Fix memory leak in vlan_reorder_header() error path, from Li
    RongQing.

 8) Fix various bugs in xen-netfront and xen-netback multiqueue support,
    from David Vrabel and Wei Liu.

 9) Fix deadlock in cxgb4 driver, from Li RongQing.

10) Prevent double free of no-cache DST entries, from Eric Dumazet.

11) Bad csum_start handling in skb_segment() leads to crashes when
    forwarding, from Tom Herbert.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  net: fix setting csum_start in skb_segment()
  ipv4: fix dst race in sk_dst_get()
  net: filter: Use kcalloc/kmalloc_array to allocate arrays
  trivial: net: filter: Change kerneldoc parameter order
  trivial: net: filter: Fix typo in comment
  net: allwinner: emac: Add missing free_irq
  cxgb4: use dev_port to identify ports
  xen-netback: bookkeep number of active queues in our own module
  tg3: Change nvram command timeout value to 50ms
  cxgb4: Not need to hold the adap_rcu_lock lock when read adap_rcu_list
  be2net: fix qnq mode detection on VFs
  of: mdio: fixup of_phy_register_fixed_link parsing of new bindings
  at86rf230: fix irq setup
  net: phy: at803x: fix coccinelle warnings
  net/mlx4_core: Fix the error flow when probing with invalid VF configuration
  tulip: Poll link status more frequently for Comet chips
  net: huawei_cdc_ncm: increase command buffer size
  drivers: net: cpsw: fix dual EMAC stall when connected to same switch
  xen-netfront: recreate queues correctly when reconnecting
  xen-netfront: fix oops when disconnected from backend
  ...

Dave Jones reported that a crash is occurring in

csum_partial
tcp_gso_segment
inet_gso_segment
? update_dl_migration
skb_mac_gso_segment
__skb_gso_segment
dev_hard_start_xmit
sch_direct_xmit
__dev_queue_xmit
? dev_hard_start_xmit
dev_queue_xmit
ip_finish_output
? ip_output
ip_output
ip_forward_finish
ip_forward
ip_rcv_finish
ip_rcv
__netif_receive_skb_core
? __netif_receive_skb_core
? trace_hardirqs_on
__netif_receive_skb
netif_receive_skb_internal
napi_gro_complete
? napi_gro_complete
dev_gro_receive
? dev_gro_receive
napi_gro_receive

It looks like a likely culprit is that SKB_GSO_CB()->csum_start is
not set correctly when doing non-scatter gather. We are using
offset as opposed to doffset.
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 7e2b10c1 ("net: Support for multiple checksums with gso")
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull NFS client fixes from Trond Myklebust:
 "Highlights include:

   - Stable fix for a data corruption case due to incorrect cache
     validation
   - Fix a couple of false positive cache invalidations
   - Fix NFSv4 security negotiation issues"

* tag 'nfs-for-3.16-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFSv4: test SECINFO RPC_AUTH_GSS pseudoflavors for support
  NFS Return -EPERM if no supported or matching SECINFO flavor
  NFS check the return of nfs4_negotiate_security in nfs4_submount
  NFS: Don't mark the data cache as invalid if it has been flushed
  NFS: Clear NFS_INO_REVAL_PAGECACHE when we update the file size
  nfs: Fix cache_validity check in nfs_write_pageuptodate()

When IP route cache had been removed in linux-3.6, we broke assumption
that dst entries were all freed after rcu grace period. DST_NOCACHE
dst were supposed to be freed from dst_release(). But it appears
we want to keep such dst around, either in UDP sockets or tunnels.

In sk_dst_get() we need to make sure dst refcount is not 0
before incrementing it, or else we might end up freeing a dst
twice.

DST_NOCACHE set on a dst does not mean this dst can not be attached
to a socket or a tunnel.

Then, before actual freeing, we need to observe a rcu grace period
to make sure all other cpus can catch the fact the dst is no longer
usable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dormando <dormando@rydia.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use kcalloc/kmalloc_array to make it clear we're allocating arrays. No
integer overflow can actually happen here, since len/flen is guaranteed
to be less than BPF_MAXINSNS (4096). However, this changed makes sure
we're not going to get one if BPF_MAXINSNS were ever increased.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the order of the parameters to sk_unattached_filter_create() in
the kerneldoc to reflect the order they appear in the actual function.

This fix is only cosmetic, in the generated doc they still appear in the
correct order without the fix.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the mdio probe function fails in emac_open, the interrupt we just requested
isn't freed. If emac_open is called again, for example because we try to set up
the interface again, the kernel will oops because the interrupt wasn't properly
released.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3f85944f ("net: Add sysfs file
for port number") introduce dev_port to network devices. cxgb4 adapters
have multiple ports on the same PCI function, and used dev_id to
identify those ports. That use was removed by commit
8c367fcb ("cxgb4: Do not set
net_device::dev_id to VI index"), since dev_id should be used only when
devices share the same MAC address.

Using dev_port for cxgb4 allows different ports on the same PCI function
to be identified.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original code uses netdev->real_num_tx_queues to bookkeep number of
queues and invokes netif_set_real_num_tx_queues to set the number of
queues. However, netif_set_real_num_tx_queues doesn't allow
real_num_tx_queues to be smaller than 1, which means setting the number
to 0 will not work and real_num_tx_queues is untouched.

This is bogus when xenvif_free is invoked before any number of queues is
allocated. That function needs to iterate through all queues to free
resources. Using the wrong number of queues results in NULL pointer
dereference.

So we bookkeep the number of queues in xen-netback to solve this
problem. This fixes a regression introduced by multiqueue patchset in
3.16-rc1.

There's another bug in original code that the real number of RX queues
is never set. In current Xen multiqueue design, the number of TX queues
and RX queues are in fact the same. We need to set the numbers of TX and
RX queues to the same value.

Also remove xenvif_select_queue and leave queue selection to core
driver, as suggested by David Miller.
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
CC: Ian Campbell <ian.campbell@citrix.com>
CC: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 506724c4 "tg3: Override clock,
link aware and link idle mode during NVRAM dump" changed the timeout
value for nvram command execution from 100ms to 1ms. But the 1ms
timeout value was only sufficient for nvram read operations but not
write operations for most of the devices supported by tg3 driver.
This patch sets the MAX to 50ms. Also it uses usleep_range instead
of udelay.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 648cd48c
The hwmon name attributes must not include '-' so the name must be
rename from gpio-fan to gpio_fan
Signed-off-by: Julien D'Ascenzio <jdascenzio@yahoo.fr>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Pull ARM SoC fixes from Arnd Bergmann:
 "A new set of bug fixes for 3.16, containing patches for seven
  platforms:

  at91:
    - drivers/misc fix for Kconfig PWM symbol
    - correction of several values in DT after conversion to CCF
    - fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc

  imx:
    - Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
      because controller base CD/WP is not working in esdhc driver due to
      runtime PM support
    - A couple of random ventana gw5xxx board fixes
    - Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
      IPUv3 driver out of staging tree
    - Fix enet/fec clock selection on imx6sl
    - Fix display node on imx53-m53evk board
    - A couple of Cubox-i updates from Russell, which were omitted from
      the merge window due to dependency

  integrator:
    - fix an OF-related regression against 3.15

  mvebu:
    - mvebu (v7)
       - Fix broken SoC ID detection
       - Select ARM_CPU_SUSPEND for v7
       - Remove armada38x compatible string (no users yet)
       - Enable Dove SoC in mvebu_v7_defconfig
    - kirkwood
       - Fix phy-connection-type on GuruPlug board

  qcom:
    - enable gsbi driver in defconfig
    - fix section mismatch warning in serial driver

  samsung:
    - use WFI macro in platform_do_lowpower because exynos cpuhotplug
      includes a hardcoded WFI instruction and it causes compile error
      in Thumb-2 mode.
    - fix GIC reg sizes for exynos4 SoCs
    - remove reset timer counter value during boot and resume for mct
      to fix a big jump in printk timestamps
    - fix pm code to check cortex-A9 for another exynos SoCs
    - don't rely on firmware's secondary_cpu_start for mcpm

  sti:
    - Ethernet clocks were wrongly defined for STiH415/416 platforms
    - STiH416 B2020 revision E DTS file name contained uppercase, change to
      lowercase"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
  ARM: at91/dt: sam9261: remove slow RC osc
  ARM: at91/dt: define sam9261ek slow crystal frequency
  ARM: at91/dt: sam9261: correctly define mainck
  ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
  ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
  misc: atmel_pwm: fix Kconfig symbols
  ARM: integrator: fix OF-related regression
  ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
  ARM: dts: kirkwood: fix phy-connection-type for Guruplug
  ARM: EXYNOS: Don't rely on firmware's secondary_cpu_start for mcpm
  ARM: dts: imx51-eukrea-mbimxsd51-baseboard: unbreak esdhc.
  ARM: dts: imx51-babbage: Fix esdhc setup
  ARM: dts: mx5: Move the display out of soc {} node
  ARM: dts: mx5: Fix IPU port node placement
  ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
  ARM: mvebu: Fix broken SoC ID detection
  ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX_IPUV3_CORE
  ARM: multi_v7_defconfig: Add QCOM GSBI driver
  ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
  tty: serial: msm: Fix section mismatch warning
  ...

The function brcmf_usb_dlneeded() queries the device to obtain the chip
id and revision. So assigning these in bus interface before the call
resulted in chip id and revision being zero. This was introduced by:

   commit 5b8045d4
   Author: Arend van Spriel <arend@broadcom.com>
   Date:   Tue May 27 12:56:23 2014 +0200

       brcmfmac: use asynchronous firmware request in USB
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

https://bugzilla.kernel.org/show_bug.cgi?id=70191
https://bugzilla.kernel.org/show_bug.cgi?id=77581

It is observed that sometimes Tx packet is downloaded without
adding driver's txpd header. This results in firmware parsing
garbage data as packet length. Sometimes firmware is unable
to read the packet if length comes out as invalid. This stops
further traffic and timeout occurs.

The root cause is uninitialized fields in tx_info(skb->cb) of
packet used to get garbage values. In this case if
MWIFIEX_BUF_FLAG_REQUEUED_PKT flag is mistakenly set, txpd
header was skipped. This patch makes sure that tx_info is
correctly initialized to fix the problem.

Cc: <stable@vger.kernel.org>
Reported-by: Andrew Wiley <wiley.andrew.j@gmail.com>
Reported-by: Linus Gasser <list@markas-al-nour.org>
Reported-by: Michael Hirsch <hirsch@teufel.de>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge "First AT91 fixes batch for 3.16" from Nicolas Ferre:

- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc

* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
  ARM: at91/dt: sam9261: remove slow RC osc
  ARM: at91/dt: define sam9261ek slow crystal frequency
  ARM: at91/dt: sam9261: correctly define mainck
  ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
  ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
  misc: atmel_pwm: fix Kconfig symbols