Commit dacce2be ("vmxnet3: add geneve and vxlan tunnel offload
support") added support for encapsulation offload. However, the inner
offload capability is to be restrictued to UDP tunnels.

This patch fixes the issue for non-udp tunnels by adding features
check capability and filtering appropriate features for non-udp tunnels.

Fixes: dacce2be ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2020-09-25

This series contains updates to the iavf and ice driver.

Sylwester fixes a crash with iavf resume due to getting the wrong pointers.

Ani fixes a call trace in ice resume by calling pci_save_state().

Jakes fixes memory leaks in case of register_netdev() failure or
ice_cfg_vsi_lan() failure for the ice driver.

v2: Rebased; no other changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-2020-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for v5.9

Second, and last, set of fixes for v5.9. Only one important regression
fix for mt76.

mt76

* fix a regression in aggregation which appeared after mac80211 changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

During ice_vsi_setup, if ice_cfg_vsi_lan fails, it does not properly
release memory associated with the VSI rings. If we had used devres
allocations for the rings, this would be ok. However, we use kzalloc and
kfree_rcu for these ring structures.

Using the correct label to cleanup the rings during ice_vsi_setup
highlights an issue in the ice_vsi_clear_rings function: it can leave
behind stale ring pointers in the q_vectors structure.

When releasing rings, we must also ensure that no q_vector associated
with the VSI will point to this ring again. To resolve this, loop over
all q_vectors and release their ring mapping. Because we are about to
free all rings, no q_vector should remain pointing to any of the rings
in this VSI.

Fixes: 5513b920 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The ice_setup_pf_sw function can cause a memory leak if register_netdev
fails, due to accidentally failing to free the VSI rings. Fix the memory
leak by using ice_vsi_release, ensuring we actually go through the full
teardown process.

This should be safe even if the netdevice is not registered because we
will have set the netdev pointer to NULL, ensuring ice_vsi_release won't
call unregister_netdev.

An alternative fix would be moving management of the PF VSI netdev into
the main VSI setup code. This is complicated and likely requires
significant refactor in how we manage VSIs

Fixes: 3a858ba3 ("ice: Add support for VSI allocation and deallocation")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

It appears that the ice_suspend flow is missing a call to pci_save_state
and this is triggering the message "State of device not saved by
ice_suspend" and a call trace. Fix it.

Fixes: 769c500d ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

When calling iavf_resume there was a crash because wrong
function was used to get iavf_adapter and net_device pointers.
Changed how iavf_resume is getting iavf_adapter and net_device
pointers from pci_dev.

Fixes: 5eae00c5 ("i40evf: main driver core")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Currently, we use length of DSACKed range to compute number of
delivered packets. And if sequence range in DSACK is corrupted,
we can get bogus dsacked/acked count, and bogus cwnd.

This patch put bounds on DSACKed range to skip update of data
delivery and spurious retransmission information, if the DSACK
is unlikely caused by sender's action:
- DSACKed range shouldn't be greater than maximum advertised rwnd.
- Total no. of DSACKed segments shouldn't be greater than total
  no. of retransmitted segs. Unlike spurious retransmits, network
  duplicates or corrupted DSACKs shouldn't be counted as delivery.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MDIO reads can happen during PHY probing, and printing an error with
dev_err can result in a large number of error messages during device
probe.  On a platform with a serial console this can result in
excessively long boot times in a way that looks like an infinite loop
when multiple busses are present.  Since 0f183fd1 (net/fsl: enable
extended scanning in xgmac_mdio) we perform more scanning so there are
potentially more failures.

Reduce the logging level to dev_dbg which is consistent with the
Freescale enetc driver.

Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Jamie Iles <jamie@nuviainc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous implementation failed to account for the "ports" node. The
actual port nodes are not child nodes of the switch node, but a "ports"
node sits in between.

Fixes: edecfa98 ("net: dsa: microchip: look for phy-mode in port nodes")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

BUG: kernel NULL pointer dereference, address: 00000000000000b8
 #PF: supervisor read access in kernel mode
 #PF: error_code(0x0000) - not-present page
 PGD 80000008b6fef067 P4D 80000008b6fef067 PUD 8b6fe6067 PMD 0
 Oops: 0000 [#1] SMP PTI
 CPU: 12 PID: 23871 Comm: kworker/12:80 Kdump: loaded Tainted: G S
 5.9.0-rc3+ #1
 Hardware name: Supermicro X10SRA-F/X10SRA-F, BIOS 2.1 03/29/2018
 Workqueue: events tx_work_handler [tls]
 RIP: 0010:tx_work_handler+0x1b/0x70 [tls]
 Code: dc fe ff ff e8 16 d4 a3 f6 66 0f 1f 44 00 00 0f 1f 44 00 00 55 53 48 8b
 6f 58 48 8b bd a0 04 00 00 48 85 ff 74 1c 48 8b 47 28 <48> 8b 90 b8 00 00 00 83
 e2 02 75 0c f0 48 0f ba b0 b8 00 00 00 00
 RSP: 0018:ffffa44ace61fe88 EFLAGS: 00010286
 RAX: 0000000000000000 RBX: ffff91da9e45cc30 RCX: dead000000000122
 RDX: 0000000000000001 RSI: ffff91da9e45cc38 RDI: ffff91d95efac200
 RBP: ffff91da133fd780 R08: 0000000000000000 R09: 000073746e657665
 R10: 8080808080808080 R11: 0000000000000000 R12: ffff91dad7d30700
 R13: ffff91dab6561080 R14: 0ffff91dad7d3070 R15: ffff91da9e45cc38
 FS:  0000000000000000(0000) GS:ffff91dad7d00000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 00000000000000b8 CR3: 0000000906478003 CR4: 00000000003706e0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
 Call Trace:
  process_one_work+0x1a7/0x370
  worker_thread+0x30/0x370
  ? process_one_work+0x370/0x370
  kthread+0x114/0x130
  ? kthread_park+0x80/0x80
  ret_from_fork+0x22/0x30

tls_sw_release_resources_tx() waits for encrypt_pending, which
can have race, so we need similar changes as in commit
0cada332 here as well.

Fixes: a42055e8 ("net/tls: Add support for async encryption of records for performance")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify the comment typo: "compliment" -> "complement".
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

INIT_IPS and GATE_ENABLE fields have a wrong offset in SG_CONFIG_REG_3.
This register is used by stream gate control of PSFP, and it has not
been used before, because PSFP is not implemented in ocelot driver.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

state->speed holds a value of 10, 100, 1000 or 2500, but
QSYS_TAG_CONFIG_LINK_SPEED expects a value of 0, 1, 2, 3. So convert the
speed to a proper value.

Fixes: de143c0e ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It should also be regarded as an error when hw return status=4 for PF's
setting mac cmd. Only if PF return status=4 to VF should this cmd be
taken special treatment.

Fixes: 7dd29ee1 ("hinic: add sriov feature support")
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1.
Move the lapb_register/lapb_unregister calls into the ndo_open/ndo_stop
functions.
This makes the LAPB protocol start/stop when the network interface
starts/stops. When the network interface is down, the LAPB protocol
shouldn't be running and the LAPB module shoudn't be generating control
frames.

2.
Move netif_start_queue/netif_stop_queue into the ndo_open/ndo_stop
functions.
This makes the TX queue start/stop when the network interface
starts/stops.
(netif_stop_queue was originally in the ndo_stop function. But to make
the code look better, I created a new function to use as ndo_stop, and
made it call the original ndo_stop function. I moved netif_stop_queue
from the original ndo_stop function to the new ndo_stop function.)

Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/networking/ip-sysctl.txt:46 says:
  ip_forward_use_pmtu - BOOLEAN
    By default we don't trust protocol path MTUs while forwarding
    because they could be easily forged and can lead to unwanted
    fragmentation by the router.
    You only need to enable this if you have user-space software
    which tries to discover path mtus by itself and depends on the
    kernel honoring this information. This is normally not the case.
    Default: 0 (disabled)
    Possible values:
    0 - disabled
    1 - enabled

Which makes it pretty clear that setting it to 1 is a potential
security/safety/DoS issue, and yet it is entirely reasonable to want
forwarded traffic to honour explicitly administrator configured
route mtus (instead of defaulting to device mtu).

Indeed, I can't think of a single reason why you wouldn't want to.
Since you configured a route mtu you probably know better...

It is pretty common to have a higher device mtu to allow receiving
large (jumbo) frames, while having some routes via that interface
(potentially including the default route to the internet) specify
a lower mtu.

Note that ipv6 forwarding uses device mtu unless the route is locked
(in which case it will use the route mtu).

This approach is not usable for IPv4 where an 'mtu lock' on a route
also has the side effect of disabling TCP path mtu discovery via
disabling the IPv4 DF (don't frag) bit on all outgoing frames.

I'm not aware of a way to lock a route from an IPv6 RA, so that also
potentially seems wrong.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Sunmeet Gill (Sunny) <sgill@quicinc.com>
Cc: Vinay Paradkar <vparadka@qti.qualcomm.com>
Cc: Tyler Wear <twear@quicinc.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cong Wang says:

====================
net_sched: fix a UAF in tcf_action_init()

This patchset fixes a use-after-free triggered by syzbot. Please
find more details in each patch description.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot is able to trigger a failure case inside the loop in
tcf_action_init(), and when this happens we clean up with
tcf_action_destroy(). But, as these actions are already inserted
into the global IDR, other parallel process could free them
before tcf_action_destroy(), then we will trigger a use-after-free.

Fix this by deferring the insertions even later, after the loop,
and committing all the insertions in a separate loop, so we will
never fail in the middle of the insertions any more.

One side effect is that the window between alloction and final
insertion becomes larger, now it is more likely that the loop in
tcf_del_walker() sees the placeholder -EBUSY pointer. So we have
to check for error pointer in tcf_del_walker().

Reported-and-tested-by: syzbot+2287853d392e4b42374a@syzkaller.appspotmail.com
Fixes: 0190c1d4 ("net: sched: atomically check-allocate action")
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All TC actions call tcf_idr_insert() for new action at the end
of their ->init(), so we can actually move it to a central place
in tcf_action_init_1().

And once the action is inserted into the global IDR, other parallel
process could free it immediately as its refcnt is still 1, so we can
not fail after this, we need to move it after the goto action
validation to avoid handling the failure case after insertion.

This is found during code review, is not directly triggered by syzbot.
And this prepares for the next patch.

Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After fixing mac80211 to allow larger A-MSDUs in some cases, there have been
reports of performance regressions and packet loss with some clients.
It appears that the issue occurs when the hardware is transmitting A-MSDUs
bigger than 8k. Limit the local VHT MPDU size capability to 7991, matching
the value used for MT7915 as well.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200923052442.24141-1-nbd@nbd.name

EEE should be only be enabled during stmmac_mac_link_up() when the
link are up and being set up properly. set_eee should only do settings
configuration and disabling the eee.

Without this fix, turning on EEE using ethtool will return
"Operation not supported". This is due to the driver is in a dead loop
waiting for eee to be advertised in the for eee to be activated but the
driver will only configure the EEE advertisement after the eee is
activated.

Ethtool should only return "Operation not supported" if there is no EEE
capbility in the MAC controller.

Fixes: 8a7493e5 ("net: stmmac: Fix a race in EEE enable callback")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The TX DMA channel data is accessed by the xrx200_start_xmit() and the
xrx200_tx_housekeeping() function from different threads. Make sure the
accesses are synchronized by acquiring the netif_tx_lock() in the
xrx200_tx_housekeeping() function too. This lock is acquired by the
kernel before calling xrx200_start_xmit().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update kernel-doc line comments to fix warnings reported by make W=1.
net/switchdev/switchdev.c:413: warning: Function parameter or
member 'extack' not described in 'call_switchdev_notifiers'
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 1838d6c6.

This commit moved the ravb_mdio_init() call (and thus the
of_mdiobus_register() call) from the ravb_probe() to the ravb_open()
call.  This causes a regression during system resume (s2idle/s2ram), as
new PHY devices cannot be bound while suspended.

During boot, the Micrel PHY is detected like this:

    Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=228)
    ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off

During system suspend, (A) defer_all_probes is set to true, and (B)
usermodehelper_disabled is set to UMH_DISABLED, to avoid drivers being
probed while suspended.

  A. If CONFIG_MODULES=n, phy_device_register() calling device_add()
     merely adds the device, but does not probe it yet, as
     really_probe() returns early due to defer_all_probes being set:

       dpm_resume+0x128/0x4f8
	 device_resume+0xcc/0x1b0
	   dpm_run_callback+0x74/0x340
	     ravb_resume+0x190/0x1b8
	       ravb_open+0x84/0x770
		 of_mdiobus_register+0x1e0/0x468
		   of_mdiobus_register_phy+0x1b8/0x250
		     of_mdiobus_phy_device_register+0x178/0x1e8
		       phy_device_register+0x114/0x1b8
			 device_add+0x3d4/0x798
			   bus_probe_device+0x98/0xa0
			     device_initial_probe+0x10/0x18
			       __device_attach+0xe4/0x140
				 bus_for_each_drv+0x64/0xc8
				   __device_attach_driver+0xb8/0xe0
				     driver_probe_device.part.11+0xc4/0xd8
				       really_probe+0x32c/0x3b8

     Later, phy_attach_direct() notices no PHY driver has been bound,
     and falls back to the Generic PHY, leading to degraded operation:

       Generic PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=POLL)
       ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off

  B. If CONFIG_MODULES=y, request_module() returns early with -EBUSY due
     to UMH_DISABLED, and MDIO initialization fails completely:

       mdio_bus e6800000.ethernet-ffffffff:00: error -16 loading PHY driver module for ID 0x00221622
       ravb e6800000.ethernet eth0: failed to initialize MDIO
       PM: dpm_run_callback(): ravb_resume+0x0/0x1b8 returns -16
       PM: Device e6800000.ethernet failed to resume: error -16

     Ignoring -EBUSY in phy_request_driver_module(), like was done for
     -ENOENT in commit 21e19442 ("net: phy: fix issue with loading
     PHY driver w/o initramfs"), would makes it fall back to the Generic
     PHY, like in the CONFIG_MODULES=n case.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When receiving a DATA_FIN MPTCP option on a TCP FIN packet, the DATA_FIN
information would be stored but the MPTCP worker did not get
scheduled. In turn, the MPTCP socket state would remain in
TCP_ESTABLISHED and no blocked operations would be awakened.

TCP FIN packets are seen by the MPTCP socket when moving skbs out of the
subflow receive queues, so schedule the MPTCP worker when a skb with
DATA_FIN but no data payload is moved from a subflow queue. Other cases
(DATA_FIN on a bare TCP ACK or on a packet with data payload) are
already handled.

Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/84
Fixes: 43b54c6e ("mptcp: Use full MPTCP-level disconnect state machine")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull vfs fixes from Al Viro:
 "No common topic, just assorted fixes"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fuse: fix the ->direct_IO() treatment of iov_iter
  fs: fix cast in fsparam_u32hex() macro
  vboxsf: Fix the check for the old binary mount-arguments struct

Pull networking fixes from Jakub Kicinski:

 - fix failure to add bond interfaces to a bridge, the offload-handling
   code was too defensive there and recent refactoring unearthed that.
   Users complained (Ido)

 - fix unnecessarily reflecting ECN bits within TOS values / QoS marking
   in TCP ACK and reset packets (Wei)

 - fix a deadlock with bpf iterator. Hopefully we're in the clear on
   this front now... (Yonghong)

 - BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)

 - fix AQL on mt76 devices with FW rate control and add a couple of AQL
   issues in mac80211 code (Felix)

 - fix authentication issue with mwifiex (Maximilian)

 - WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)

 - fix exception handling for multipath routes via same device (David
   Ahern)

 - revert back to a BH spin lock flavor for nsid_lock: there are paths
   which do require the BH context protection (Taehee)

 - fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)

 - fix ife module load deadlock (Cong)

 - make an adjustment to netlink reply message type for code added in
   this release (the sole change touching uAPI here) (Michal)

 - a number of fixes for small NXP and Microchip switches (Vladimir)

[ Pull request acked by David: "you can expect more of this in the
  future as I try to delegate more things to Jakub" ]

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
  net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
  net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
  net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
  inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
  net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
  net: Update MAINTAINERS for MediaTek switch driver
  net/mlx5e: mlx5e_fec_in_caps() returns a boolean
  net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
  net/mlx5e: kTLS, Fix leak on resync error flow
  net/mlx5e: kTLS, Add missing dma_unmap in RX resync
  net/mlx5e: kTLS, Fix napi sync and possible use-after-free
  net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
  net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
  net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
  net/mlx5e: Fix endianness when calculating pedit mask first bit
  net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
  net/mlx5e: CT: Fix freeing ct_label mapping
  net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
  net/mlx5e: Use synchronize_rcu to sync with NAPI
  net/mlx5e: Use RCU to protect rq->xdp_prog
  ...

Pull io_uring fixes from Jens Axboe:
 "A few fixes - most of them regression fixes from this cycle, but also
  a few stable heading fixes, and a build fix for the included demo tool
  since some systems now actually have gettid() available"

* tag 'io_uring-5.9-2020-09-22' of git://git.kernel.dk/linux-block:
  io_uring: fix openat/openat2 unified prep handling
  io_uring: mark statx/files_update/epoll_ctl as non-SQPOLL
  tools/io_uring: fix compile breakage
  io_uring: don't use retry based buffered reads for non-async bdev
  io_uring: don't re-setup vecs/iter in io_resumit_prep() is already there
  io_uring: don't run task work on an exiting task
  io_uring: drop 'ctx' ref on task work cancelation
  io_uring: grab any needed state during defer prep

Pull block fixes from Jens Axboe:
 "A few NVMe fixes, and a dasd write zero fix"

* tag 'block-5.9-2020-09-22' of git://git.kernel.dk/linux-block:
  nvmet: get transport reference for passthru ctrl
  nvme-core: get/put ctrl and transport module in nvme_dev_open/release()
  nvme-tcp: fix kconfig dependency warning when !CRYPTO
  nvme-pci: disable the write zeros command for Intel 600P/P3100
  s390/dasd: Fix zero write for FBA devices

Pull tracing fixes from Steven Rostedt:

 - Check kprobe is enabled before unregistering from ftrace as it isn't
   registered when disabled.

 - Remove kprobes enabled via command-line that is on init text when
   freed.

 - Add missing RCU synchronization for ftrace trampoline symbols removed
   from kallsyms.

 - Free trampoline on error path if ftrace_startup() fails.

 - Give more space for the longer PID numbers in trace output.

 - Fix a possible double free in the histogram code.

 - A couple of fixes that were discovered by sparse.

* tag 'trace-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  bootconfig: init: make xbc_namebuf static
  kprobes: tracing/kprobes: Fix to kill kprobes on initmem after boot
  tracing: fix double free
  ftrace: Let ftrace_enable_sysctl take a kernel pointer buffer
  tracing: Make the space reserved for the pid wider
  ftrace: Fix missing synchronize_rcu() removing trampoline from kallsyms
  ftrace: Free the trampoline when ftrace_startup() fails
  kprobes: Fix to check probe enabled before disarm_kprobe_ftrace()

Vladimir Oltean says:

====================
Fix broken tc-flower rules for mscc_ocelot switches

All 3 switch drivers from the Ocelot family have the same bug in the
VCAP IS2 key offsets, which is that some keys are in the incorrect
order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The IS2 IP4_TCP_UDP key offsets do not correspond to the VSC7514
datasheet. Whether they work or not is unknown to me. On VSC9959 and
VSC9953, with the same mistake and same discrepancy from the
documentation, tc-flower src_port and dst_port rules did not work, so I
am assuming the same is true here.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since these were copied from the Felix VCAP IS2 code, and only the
offsets were adjusted, the order of the bit fields is still wrong.
Fix it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of the IS2 IP4_TCP_UDP keys are not correct, like L4_DPORT,
L4_SPORT and other L4 keys. This prevents offloaded tc-flower rules from
matching on src_port and dst_port for TCP and UDP packets.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

User space could send an invalid INET_DIAG_REQ_PROTOCOL attribute
as caught by syzbot.

BUG: KMSAN: uninit-value in inet_diag_lock_handler net/ipv4/inet_diag.c:55 [inline]
BUG: KMSAN: uninit-value in __inet_diag_dump+0x58c/0x720 net/ipv4/inet_diag.c:1147
CPU: 0 PID: 8505 Comm: syz-executor174 Not tainted 5.9.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x21c/0x280 lib/dump_stack.c:118
 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:122
 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:219
 inet_diag_lock_handler net/ipv4/inet_diag.c:55 [inline]
 __inet_diag_dump+0x58c/0x720 net/ipv4/inet_diag.c:1147
 inet_diag_dump_compat+0x2a5/0x380 net/ipv4/inet_diag.c:1254
 netlink_dump+0xb73/0x1cb0 net/netlink/af_netlink.c:2246
 __netlink_dump_start+0xcf2/0xea0 net/netlink/af_netlink.c:2354
 netlink_dump_start include/linux/netlink.h:246 [inline]
 inet_diag_rcv_msg_compat+0x5da/0x6c0 net/ipv4/inet_diag.c:1288
 sock_diag_rcv_msg+0x24f/0x620 net/core/sock_diag.c:256
 netlink_rcv_skb+0x6d7/0x7e0 net/netlink/af_netlink.c:2470
 sock_diag_rcv+0x63/0x80 net/core/sock_diag.c:275
 netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline]
 netlink_unicast+0x11c8/0x1490 net/netlink/af_netlink.c:1330
 netlink_sendmsg+0x173a/0x1840 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:651 [inline]
 sock_sendmsg net/socket.c:671 [inline]
 ____sys_sendmsg+0xc82/0x1240 net/socket.c:2353
 ___sys_sendmsg net/socket.c:2407 [inline]
 __sys_sendmsg+0x6d1/0x820 net/socket.c:2440
 __do_sys_sendmsg net/socket.c:2449 [inline]
 __se_sys_sendmsg+0x97/0xb0 net/socket.c:2447
 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447
 do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x441389
Code: e8 fc ab 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 1b 09 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fff3b02ce98 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000441389
RDX: 0000000000000000 RSI: 0000000020001500 RDI: 0000000000000003
RBP: 00000000006cb018 R08: 00000000004002c8 R09: 00000000004002c8
R10: 0000000000000004 R11: 0000000000000246 R12: 0000000000402130
R13: 00000000004021c0 R14: 0000000000000000 R15: 0000000000000000

Uninit was created at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:143 [inline]
 kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:126
 kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:80
 slab_alloc_node mm/slub.c:2907 [inline]
 __kmalloc_node_track_caller+0x9aa/0x12f0 mm/slub.c:4511
 __kmalloc_reserve net/core/skbuff.c:142 [inline]
 __alloc_skb+0x35f/0xb30 net/core/skbuff.c:210
 alloc_skb include/linux/skbuff.h:1094 [inline]
 netlink_alloc_large_skb net/netlink/af_netlink.c:1176 [inline]
 netlink_sendmsg+0xdb9/0x1840 net/netlink/af_netlink.c:1894
 sock_sendmsg_nosec net/socket.c:651 [inline]
 sock_sendmsg net/socket.c:671 [inline]
 ____sys_sendmsg+0xc82/0x1240 net/socket.c:2353
 ___sys_sendmsg net/socket.c:2407 [inline]
 __sys_sendmsg+0x6d1/0x820 net/socket.c:2440
 __do_sys_sendmsg net/socket.c:2449 [inline]
 __se_sys_sendmsg+0x97/0xb0 net/socket.c:2447
 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447
 do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 3f935c75 ("inet_diag: support for wider protocol numbers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Christoph Paasch <cpaasch@apple.com>
Cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When calling the RCU brother of br_vlan_get_pvid(), lockdep warns:

=============================
WARNING: suspicious RCU usage
5.9.0-rc3-01631-g13c17acb8e38-dirty #814 Not tainted
-----------------------------
net/bridge/br_private.h:1054 suspicious rcu_dereference_protected() usage!

Call trace:
 lockdep_rcu_suspicious+0xd4/0xf8
 __br_vlan_get_pvid+0xc0/0x100
 br_vlan_get_pvid_rcu+0x78/0x108

The warning is because br_vlan_get_pvid_rcu() calls nbp_vlan_group()
which calls rtnl_dereference() instead of rcu_dereference(). In turn,
rtnl_dereference() calls rcu_dereference_protected() which assumes
operation under an RCU write-side critical section, which obviously is
not the case here. So, when the incorrect primitive is used to access
the RCU-protected VLAN group pointer, READ_ONCE() is not used, which may
cause various unexpected problems.

I'm sad to say that br_vlan_get_pvid() and br_vlan_get_pvid_rcu() cannot
share the same implementation. So fix the bug by splitting the 2
functions, and making br_vlan_get_pvid_rcu() retrieve the VLAN groups
under proper locking annotations.

Fixes: 7582f5b7 ("bridge: add br_vlan_get_pvid_rcu()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5 fixes-2020-09-18

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

v1->v2:
 Remove missing patch from -stable list.

For -stable v5.1
 ('net/mlx5: Fix FTE cleanup')

For -stable v5.3
 ('net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported')
 ('net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported')

For -stable v5.7
 ('net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready')

For -stable v5.8
 ('net/mlx5e: Use RCU to protect rq->xdp_prog')
 ('net/mlx5e: Fix endianness when calculating pedit mask first bit')
 ('net/mlx5e: Use synchronize_rcu to sync with NAPI')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update maintainers for MediaTek switch driver with Landen Chao who is
familiar with MediaTek MT753x switch devices and will help maintenance
from the vendor side.

Cc: Steven Liu <steven.liu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Returning errno is a bug, fix that.

Also fixes smatch warnings:
drivers/net/ethernet/mellanox/mlx5/core/en/port.c:453
mlx5e_fec_in_caps() warn: signedness bug returning '(-95)'

Fixes: 2132b71f ("net/mlx5e: Advertise globaly supported FEC modes")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>