Pull SCSI fix from James Bottomley:
 "This is a bug fix for the pm80xx driver.  It turns out that when the
  new hardware support was added in 3.10 the IO command size was kept at
  the old hard coded value.  This means that the driver attaches to some
  new cards and then simply hangs the system"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] pm80xx: fix Adaptec 71605H hang

Pull x86 boot fix from Peter Anvin:
 "A single very small boot fix for very large memory systems (> 0.5T)"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Fix boot crash with DEBUG_PAGE_ALLOC=y and more than 512G RAM

Pull slave-dma fix from Vinod Koul:
 "A fix for resolving TI_EDMA driver's build error in allmodconfig to
  have filter function built in""

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dma/Kconfig: TI_EDMA needs to be boolean

Pull networking fixes from David Miller:

 1) There was a simplification in the ipv6 ndisc packet sending
    attempted here, which avoided using memory accounting on the
    per-netns ndisc socket for sending NDISC packets.  It did fix some
    important issues, but it causes regressions so it gets reverted here
    too.  Specifically, the problem with this change is that the IPV6
    output path really depends upon there being a valid skb->sk
    attached.

    The reason we want to do this change in some form when we figure out
    how to do it right, is that if a device goes down the ndisc_sk
    socket send queue will fill up and block NDISC packets that we want
    to send to other devices too.  That's really bad behavior.

    Hopefully Thomas can come up with a better version of this change.

 2) Fix a severe TCP performance regression by reverting a change made
    to dev_pick_tx() quite some time ago.  From Eric Dumazet.

 3) TIPC returns wrongly signed error codes, fix from Erik Hugne.

 4) Fix OOPS when doing IPSEC over ipv4 tunnels due to orphaning the
    skb->sk too early.  Fix from Li Hongjun.

 5) RAW ipv4 sockets can use the wrong routing key during lookup, from
    Chris Clark.

 6) Similar to #1 revert an older change that tried to use plain
    alloc_skb() for SYN/ACK TCP packets, this broke the netfilter owner
    mark which needs to see the skb->sk for such frames.  From Phil
    Oester.

 7) BNX2x driver bug fixes from Ariel Elior and Yuval Mintz,
    specifically in the handling of virtual functions.

 8) IPSEC path error propagations to sockets is not done properly when
    we have v4 in v6, and v6 in v4 type rules.  Fix from Hannes Frederic
    Sowa.

 9) Fix missing channel context release in mac80211, from Johannes Berg.

10) Fix network namespace handing wrt.  SCM_RIGHTS, from Andy
    Lutomirski.

11) Fix usage of bogus NAPI weight in jme, netxen, and ps3_gelic
    drivers.  From Michal Schmidt.

12) Hopefully a complete and correct fix for the genetlink dump locking
    and module reference counting.  From Pravin B Shelar.

13) sk_busy_loop() must do a cpu_relax(), from Eliezer Tamir.

14) Fix handling of timestamp offset when restoring a snapshotted TCP
    socket.  From Andrew Vagin.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  net: fec: fix time stamping logic after napi conversion
  net: bridge: convert MLDv2 Query MRC into msecs_to_jiffies for max_delay
  mISDN: return -EINVAL on error in dsp_control_req()
  net: revert 8728c544 ("net: dev_pick_tx() fix")
  Revert "ipv6: Don't depend on per socket memory for neighbour discovery messages"
  ipv4 tunnels: fix an oops when using ipip/sit with IPsec
  tipc: set sk_err correctly when connection fails
  tcp: tcp_make_synack() should use sock_wmalloc
  bridge: separate querier and query timer into IGMP/IPv4 and MLD/IPv6 ones
  ipv6: Don't depend on per socket memory for neighbour discovery messages
  ipv4: sendto/hdrincl: don't use destination address found in header
  tcp: don't apply tsoffset if rcv_tsecr is zero
  tcp: initialize rcv_tstamp for restored sockets
  net: xilinx: fix memleak
  net: usb: Add HP hs2434 device to ZLP exception table
  net: add cpu_relax to busy poll loop
  net: stmmac: fixed the pbl setting with DT
  genl: Hold reference on correct module while netlink-dump.
  genl: Fix genl dumpit() locking.
  xfrm: Fix potential null pointer dereference in xdst_queue_output
  ...

Filtering capabilities on my work email are pretty much non-existent and this
has turned out to be something of a firehose...

Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull sound fixes from Takashi Iwai:
 "This contains two Oops fixes (opti9xx and HD-audio) and a simple fixup
  for an Acer laptop.  All marked as stable patches"

* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: opti9xx: Fix conflicting driver object name
  ALSA: hda - Fix NULL dereference with CONFIG_SND_DYNAMIC_MINORS=n
  ALSA: hda - Add inverted digital mic fixup for Acer Aspire One

Pull ARM SoC fixes from Olof Johansson:
 "Two straggling fixes that I had missed as they were posted a couple of
  weeks ago, causing problems with interrupts (breaking them completely)
  on the CSR SiRF platforms"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm: prima2: drop nr_irqs in mach as we moved to linear irqdomain
  irqchip: sirf: move from legacy mode to linear irqdomain

Pull drm fixes from Dave Airlie:
 "Since we are getting to the pointy end, one i915 black screen on some
  machines, and one vmwgfx stop userspace ability to nuke the VM,

  There might be one or two ati or nouveau fixes trickle in before
  final, but I think this should pretty much be it"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/vmwgfx: Split GMR2_REMAP commands if they are to large
  drm/i915: ivb: fix edp voltage swing reg val

Pull input layer updates from Dmitry Torokhov:
 "Just a couple of new IDs in Wacom and xpad drivers, i8042 is now
  disabled on ARC, and data checks in Elantech driver that were overly
  relaxed by the previous patch are now tightened"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: i8042 - disable the driver on ARC platforms
  Input: xpad - add signature for Razer Onza Classic Edition
  Input: elantech - fix packet check for v3 and v4 hardware
  Input: wacom - add support for 0x300 and 0x301

Commit dc975382 "net: fec: add napi support to improve proformance"
converted the fec driver to the napi model. However, that commit
forgot to remove the call to skb_defer_rx_timestamp which is only
needed in non-napi drivers.

(The function napi_gro_receive eventually calls netif_receive_skb,
which in turn calls skb_defer_rx_timestamp.)

This patch should also be applied to the 3.9 and 3.10 kernels.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While looking into MLDv1/v2 code, I noticed that bridging code does
not convert it's max delay into jiffies for MLDv2 messages as we do
in core IPv6' multicast code.

RFC3810, 5.1.3. Maximum Response Code says:

  The Maximum Response Code field specifies the maximum time allowed
  before sending a responding Report. The actual time allowed, called
  the Maximum Response Delay, is represented in units of milliseconds,
  and is derived from the Maximum Response Code as follows: [...]

As we update timers that work with jiffies, we need to convert it.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Linus Lüssing <linus.luessing@web.de>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If skb->len is too short then we should return an error.  Otherwise we
read beyond the end of skb->data for several bytes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 8728c544 ("net: dev_pick_tx() fix") and commit
b6fe83e9 ("bonding: refine IFF_XMIT_DST_RELEASE capability")
are quite incompatible : Queue selection is disabled because skb
dst was dropped before entering bonding device.

This causes major performance regression, mainly because TCP packets
for a given flow can be sent to multiple queues.

This is particularly visible when using the new FQ packet scheduler
with MQ + FQ setup on the slaves.

We can safely revert the first commit now that 416186fb
("net: Split core bits of netdev_pick_tx into __netdev_pick_tx")
properly caps the queue_index.
Reported-by: Xi Wang <xii@google.com>
Diagnosed-by: Xi Wang <xii@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Denys Fedorysychenko <nuclearcat@nuclearcat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 1f324e38.

It seems to cause regressions, and in particular the output path
really depends upon there being a socket attached to skb->sk for
checks such as sk_mc_loop(skb->sk) for example.  See ip6_output_finish2().
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 3d7b46cd (ip_tunnel: push generic protocol handling to
ip_tunnel module.), an Oops is triggered when an xfrm policy is configured on
an IPv4 over IPv4 tunnel.

xfrm4_policy_check() calls __xfrm_policy_check2(), which uses skb_dst(skb). But
this field is NULL because iptunnel_pull_header() calls skb_dst_drop(skb).
Signed-off-by: Li Hongjun <hongjun.li@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Should a connect fail, if the publication/server is unavailable or
due to some other error, a positive value will be returned and errno
is never set. If the application code checks for an explicit zero
return from connect (success) or a negative return (failure), it
will not catch the error and subsequent send() calls will fail as
shown from the strace snippet below.

socket(0x1e /* PF_??? */, SOCK_SEQPACKET, 0) = 3
connect(3, {sa_family=0x1e /* AF_??? */, sa_data="\2\1\322\4\0\0\322\4\0\0\0\0\0\0"}, 16) = 111
sendto(3, "test", 4, 0, NULL, 0)        = -1 EPIPE (Broken pipe)

The reason for this behaviour is that TIPC wrongly inverts error
codes set in sk_err.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 90ba9b19 (tcp: tcp_make_synack() can use alloc_skb()), Eric changed
the call to sock_wmalloc in tcp_make_synack to alloc_skb.  In doing so,
the netfilter owner match lost its ability to block the SYNACK packet on
outbound listening sockets.  Revert the change, restoring the owner match
functionality.

This closes netfilter bugzilla #847.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we would still potentially suffer multicast packet loss if there
is just either an IGMP or an MLD querier: For the former case, we would
possibly drop IPv6 multicast packets, for the latter IPv4 ones. This is
because we are currently assuming that if either an IGMP or MLD querier
is present that the other one is present, too.

This patch makes the behaviour and fix added in
"bridge: disable snooping if there is no querier" (b00589af)
to also work if there is either just an IGMP or an MLD querier on the
link: It refines the deactivation of the snooping to be protocol
specific by using separate timers for the snooped IGMP and MLD queries
as well as separate timers for our internal IGMP and MLD queriers.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull cgroup fix from Tejun Heo:
 "During the percpu reference counting update which was merged during
  v3.11-rc1, the cgroup destruction path was updated so that a cgroup in
  the process of dying may linger on the children list, which was
  necessary as the cgroup should still be included in child/descendant
  iteration while percpu ref is being killed.

  Unfortunately, I forgot to update cgroup destruction path accordingly
  and cgroup destruction may fail spuriously with -EBUSY due to
  lingering dying children even when there's no live child left - e.g.
  "rmdir parent/child parent" will usually fail.

  This can be easily fixed by iterating through the children list to
  verify that there's no live child left.  While this is very late in
  the release cycle, this bug is very visible to userland and I believe
  the fix is relatively safe.

  Thanks Hugh for spotting and providing fix for the issue"

* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: fix rmdir EBUSY regression in 3.11

Pull workqueue fix from Tejun Heo:
 "This contains one fix which could lead to system-wide lockup on
  !PREEMPT kernels.  It's very late in the cycle but this definitely is
  a -stable material.

  The problem is that workqueue worker tasks may process unlimited
  number of work items back-to-back without every yielding inbetween.
  This usually isn't noticeable but a work item which re-queues itself
  waiting for someone else to do something can deadlock with
  stop_machine.  stop_machine will ensure nothing else happens on all
  other cpus and the requeueing work item will reqeueue itself
  indefinitely without ever yielding and thus preventing the CPU from
  entering stop_machine.

  Kudos to Jamie Liu for spotting and diagnosing the problem.  This can
  be trivially fixed by adding cond_resched() after processing each work
  item"

* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: cond_resched() after processing each work item

Pull NFS client bugfix from Trond Myklebust:
 "Stable patch to fix a highmem-related data corruption issue on 32-bit
  ARM platforms"

* tag 'nfs-for-3.11-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  SUNRPC: Fix memory corruption issue on 32-bit highmem systems

This fixes the piglit test texturing/max-texture-size
causing the VM to die due to a too large SVGA command.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Biran Paul <brianp@vmware.com>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@gmail.com>

Merge tag 'drm-intel-fixes-2013-08-30' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes

Just a one-line patch to fix a black screen issue on rare ivb machines,
cc: stable. Normally I'd just shovel this into the -next pull request this
late in the -rc cycle, but Linus was making noises about not getting real
fixes which are cc: stable. So here we go ;-)

* tag 'drm-intel-fixes-2013-08-30' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: ivb: fix edp voltage swing reg val

Fix the typo introduced in

commit 1a2eb460
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Nov 16 16:26:07 2011 -0800

    drm/i915: Hook up Ivybridge eDP

This fixes eDP link-training failures and cases where all voltage swing
/pre-emphasis levels were tried and failed during clock recovery and -
as a fallback - we go on to do channel equalization with the last voltage
swing/pre-emphasis level which will succeed. Both issues can lead to a
blank screen.

v2:
- improve commit message

CC: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64880Tested-by: Jeremy Moles <cubicool@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Steffen Klassert says:

====================
This pull request fixes some issues that arise when 6in4 or 4in6 tunnels
are used in combination with IPsec, all from Hannes Frederic Sowa and a
null pointer dereference when queueing packets to the policy hold queue.

1) We might access the local error handler of the wrong address family if
   6in4 or 4in6 tunnel is protected by ipsec. Fix this by addind a pointer
   to the correct local_error to xfrm_state_afinet.

2) Add a helper function to always refer to the correct interpretation
   of skb->sk.

3) Call skb_reset_inner_headers to record the position of the inner headers
   when adding a new one in various ipv6 tunnels. This is needed to identify
   the addresses where to send back errors in the xfrm layer.

4) Dereference inner ipv6 header if encapsulated to always call the
   right error handler.

5) Choose protocol family by skb protocol to not call the wrong
   xfrm{4,6}_local_error handler in case an ipv6 sockets is used
   in ipv4 mode.

6) Partly revert "xfrm: introduce helper for safe determination of mtu"
   because this introduced pmtu discovery problems.

7) Set skb->protocol on tcp, raw and ip6_append_data genereated skbs.
   We need this to get the correct mtu informations in xfrm.

8) Fix null pointer dereference in xdst_queue_output.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocating skbs when sending out neighbour discovery messages
currently uses sock_alloc_send_skb() based on a per net namespace
socket and thus share a socket wmem buffer space.

If a netdevice is temporarily unable to transmit due to carrier
loss or for other reasons, the queued up ndisc messages will cosnume
all of the wmem space and will thus prevent from any more skbs to
be allocated even for netdevices that are able to transmit packets.

The number of neighbour discovery messages sent is very limited,
simply use alloc_skb() and don't depend on any socket wmem space any
longer.

This patch has orginally been posted by Eric Dumazet in a modified
form.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: raw_sendmsg: don't use header's destination address

A sendto() regression was bisected and found to start with commit
f8126f1d (ipv4: Adjust semantics of rt->rt_gateway.)

The problem is that it tries to ARP-lookup the constructed packet's
destination address rather than the explicitly provided address.

Fix this using FLOWI_FLAG_KNOWN_NH so that given nexthop is used.

cf. commit 2ad5b9e4Reported-by: Chris Clark <chris.clark@alcatel-lucent.com>
Bisected-by: Chris Clark <chris.clark@alcatel-lucent.com>
Tested-by: Chris Clark <chris.clark@alcatel-lucent.com>
Suggested-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Chris Clark <chris.clark@alcatel-lucent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The zero value means that tsecr is not valid, so it's a special case.

tsoffset is used to customize tcp_time_stamp for one socket.
tsoffset is usually zero, it's used when a socket was moved from one
host to another host.

Currently this issue affects logic of tcp_rcv_rtt_measure_ts. Due to
incorrect value of rcv_tsecr, tcp_rcv_rtt_measure_ts sets rto to
TCP_RTO_MAX.

Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Reported-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

u32 rcv_tstamp;     /* timestamp of last received ACK */

Its value used in tcp_retransmit_timer, which closes socket
if the last ack was received more then TCP_RTO_MAX ago.

Currently rcv_tstamp is initialized to zero and if tcp_retransmit_timer
is called before receiving a first ack, the connection is closed.

This patch initializes rcv_tstamp to a timestamp, when a socket was
restored.

Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Reported-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

we don't need nr_irqs in machine any more after we move to
linear irqdomain for sirfsoc irqchip, so drop them.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

the series of patches for irqdomain core in 3.11 has broken sirf
irq which uses legacy mapping. all users fail in the new kernel
while setupping irq.

this patch moves to linear irqdomain and drop old legacy irqdomain
codes since we don't need it any more, and at the same time, it
also fixes the broken interrupts of sirfsoc in 3.11.

on the other hand, we actually only have 64 interrupt sources for
prima2 and atlas6, but there are 128 interrupt souces for marco
which uses GIC. in the legacy codes, sirf gpio also uses legacy
irqdomain, so to make gpio interrupt mapping not depend on the
prima2/atlas6/marco an use unified marco,we enlarge prima2/atlas6
interrupt number to 128. here we don't need this workaround any
more as sirf gpio also moved to linear mode before. so we move
SIRFSOC_NUM_IRQS back to 64 too.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

It causes crashes when enabled, and we don't have such a peripheral
anyway on ARC platforms.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

On 3.11-rc we are seeing cgroup directories left behind when they should
have been removed.  Here's a trivial reproducer:

cd /sys/fs/cgroup/memory
mkdir parent parent/child; rmdir parent/child parent
rmdir: failed to remove `parent': Device or resource busy

It's because cgroup_destroy_locked() (step 1 of destruction) leaves
cgroup on parent's children list, letting cgroup_offline_fn() (step 2 of
destruction) remove it; but step 2 is run by work queue, which may not
yet have removed the children when parent destruction checks the list.

Fix that by checking through a non-empty list of children: if every one
of them has already been marked CGRP_DEAD, then it's safe to proceed:
those children are invisible to userspace, and should not obstruct rmdir.

(I didn't see any reason to keep the cgrp->children checks under the
unrelated css_set_lock, so moved them out.)

tj: Flattened nested ifs a bit and updated comment so that it's
    correct on both for-3.11-fixes and for-3.12.
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

If !PREEMPT, a kworker running work items back to back can hog CPU.
This becomes dangerous when a self-requeueing work item which is
waiting for something to happen races against stop_machine.  Such
self-requeueing work item would requeue itself indefinitely hogging
the kworker and CPU it's running on while stop_machine would wait for
that CPU to enter stop_machine while preventing anything else from
happening on all other CPUs.  The two would deadlock.

Jamie Liu reports that this deadlock scenario exists around
scsi_requeue_run_queue() and libata port multiplier support, where one
port may exclude command processing from other ports.  With the right
timing, scsi_requeue_run_queue() can end up requeueing itself trying
to execute an IO which is asked to be retried while another device has
an exclusive access, which in turn can't make forward progress due to
stop_machine.

Fix it by invoking cond_resched() after executing each work item.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jamie Liu <jamieliu@google.com>
References: http://thread.gmane.org/gmane.linux.kernel/1552567
Cc: stable@vger.kernel.org
--
 kernel/workqueue.c |    9 +++++++++
 1 file changed, 9 insertions(+)

Merge fixes from Andrew Morton:
 "Five fixes.

  err, make that six.  let me try again"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  fs/ocfs2/super.c: Use bigger nodestr to accomodate 32-bit node numbers
  memcg: check that kmem_cache has memcg_params before accessing it
  drivers/base/memory.c: fix show_mem_removable() to handle missing sections
  IPC: bugfix for msgrcv with msgtyp < 0
  Omnikey Cardman 4000: pull in ioctl.h in user header
  timer_list: correct the iterator for timer_list

While using pacemaker/corosync, the node numbers are generated using IP
address as opposed to serial node number generation.  This may not fit
in a 8-byte string.  Use a bigger string to print the complete node
number.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If the system had a few memory groups and all of them were destroyed,
memcg_limited_groups_array_size has non-zero value, but all new caches
are created without memcg_params, because memcg_kmem_enabled() returns
false.

We try to enumirate child caches in a few places and all of them are
potentially dangerous.

For example my kernel is compiled with CONFIG_SLAB and it crashed when I
tryed to mount a NFS share after a few experiments with kmemcg.

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
  IP: [<ffffffff8118166a>] do_tune_cpucache+0x8a/0xd0
  PGD b942a067 PUD b999f067 PMD 0
  Oops: 0000 [#1] SMP
  Modules linked in: fscache(+) ip6table_filter ip6_tables iptable_filter ip_tables i2c_piix4 pcspkr virtio_net virtio_balloon i2c_core floppy
  CPU: 0 PID: 357 Comm: modprobe Not tainted 3.11.0-rc7+ #59
  Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
  task: ffff8800b9f98240 ti: ffff8800ba32e000 task.ti: ffff8800ba32e000
  RIP: 0010:[<ffffffff8118166a>]  [<ffffffff8118166a>] do_tune_cpucache+0x8a/0xd0
  RSP: 0018:ffff8800ba32fb70  EFLAGS: 00010246
  RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000006
  RDX: 0000000000000000 RSI: ffff8800b9f98910 RDI: 0000000000000246
  RBP: ffff8800ba32fba0 R08: 0000000000000002 R09: 0000000000000004
  R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000010
  R13: 0000000000000008 R14: 00000000000000d0 R15: ffff8800375d0200
  FS:  00007f55f1378740(0000) GS:ffff8800bfa00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
  CR2: 00007f24feba57a0 CR3: 0000000037b51000 CR4: 00000000000006f0
  Call Trace:
    enable_cpucache+0x49/0x100
    setup_cpu_cache+0x215/0x280
    __kmem_cache_create+0x2fa/0x450
    kmem_cache_create_memcg+0x214/0x350
    kmem_cache_create+0x2b/0x30
    fscache_init+0x19b/0x230 [fscache]
    do_one_initcall+0xfa/0x1b0
    load_module+0x1c41/0x26d0
    SyS_finit_module+0x86/0xb0
    system_call_fastpath+0x16/0x1b
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Glauber Costa <glommer@openvz.org>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

"cat /sys/devices/system/memory/memory*/removable" crashed the system.

The problem is that show_mem_removable() is passing a
bad pfn to is_mem_section_removable(), which causes

    if (!node_online(page_to_nid(page)))

to blow up.  Why is it passing in a bad pfn?

The reason is that show_mem_removable() will loop sections_per_block
times.  sections_per_block is 16, but mem->section_count is 8,
indicating holes in this memory block.  Checking that the memory section
is present before checking to see if the memory section is removable
fixes the problem.

   harp5-sys:~ # cat /sys/devices/system/memory/memory*/removable
   0
   1
   1
   1
   1
   1
   1
   1
   1
   1
   1
   1
   1
   1
   BUG: unable to handle kernel paging request at ffffea00c3200000
   IP: [<ffffffff81117ed1>] is_pageblock_removable_nolock+0x1/0x90
   PGD 83ffd4067 PUD 37bdfce067 PMD 0
   Oops: 0000 [#1] SMP
   Modules linked in: autofs4 binfmt_misc rdma_ucm rdma_cm iw_cm ib_addr ib_srp scsi_transport_srp scsi_tgt ib_ipoib ib_cm ib_uverbs ib_umad iw_cxgb3 cxgb3 mdio mlx4_en mlx4_ib ib_sa mlx4_core ib_mthca ib_mad ib_core fuse nls_iso8859_1 nls_cp437 vfat fat joydev loop hid_generic usbhid hid hwperf(O) numatools(O) dm_mod iTCO_wdt ipv6 iTCO_vendor_support igb i2c_i801 ioatdma i2c_algo_bit ehci_pci pcspkr lpc_ich i2c_core ehci_hcd ptp sg mfd_core dca rtc_cmos pps_core mperf button xhci_hcd sd_mod crc_t10dif usbcore usb_common scsi_dh_emc scsi_dh_hp_sw scsi_dh_alua scsi_dh_rdac scsi_dh gru(O) xvma(O) xfs crc32c libcrc32c thermal sata_nv processor piix mptsas mptscsih scsi_transport_sas mptbase megaraid_sas fan thermal_sys hwmon ext3 jbd ata_piix ahci libahci libata scsi_mod
   CPU: 4 PID: 5991 Comm: cat Tainted: G           O 3.11.0-rc5-rja-uv+ #10
   Hardware name: SGI UV2000/ROMLEY, BIOS SGI UV 2000/3000 series BIOS 01/15/2013
   task: ffff88081f034580 ti: ffff880820022000 task.ti: ffff880820022000
   RIP: 0010:[<ffffffff81117ed1>]  [<ffffffff81117ed1>] is_pageblock_removable_nolock+0x1/0x90
   RSP: 0018:ffff880820023df8  EFLAGS: 00010287
   RAX: 0000000000040000 RBX: ffffea00c3200000 RCX: 0000000000000004
   RDX: ffffea00c30b0000 RSI: 00000000001c0000 RDI: ffffea00c3200000
   RBP: ffff880820023e38 R08: 0000000000000000 R09: 0000000000000001
   R10: 0000000000000000 R11: 0000000000000001 R12: ffffea00c33c0000
   R13: 0000160000000000 R14: 6db6db6db6db6db7 R15: 0000000000000001
   FS:  00007ffff7fb2700(0000) GS:ffff88083fc80000(0000) knlGS:0000000000000000
   CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
   CR2: ffffea00c3200000 CR3: 000000081b954000 CR4: 00000000000407e0
   Call Trace:
     show_mem_removable+0x41/0x70
     dev_attr_show+0x2a/0x60
     sysfs_read_file+0xf7/0x1c0
     vfs_read+0xc8/0x130
     SyS_read+0x5d/0xa0
     system_call_fastpath+0x16/0x1b
Signed-off-by: Russ Anderson <rja@sgi.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

According to 'man msgrcv': "If msgtyp is less than 0, the first message of
the lowest type that is less than or equal to the absolute value of msgtyp
shall be received."

Bug: The kernel only returns a message if its type is 1; other messages
with type < abs(msgtype) will never get returned.

Fix: After having traversed the list to find the first message with the
lowest type, we need to actually return that message.

This regression was introduced by commit daaf74cf ("ipc: refactor
msg list search into separate function")
Signed-off-by: Svenning Soerensen <sss@secomea.dk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This file uses the ioctl helpers (_IOR/_IOW/etc...), so include ioctl.h
for the definitions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>