The commit adds the new trace_events for TIPC link object:

trace_tipc_link_timeout()
trace_tipc_link_fsm()
trace_tipc_link_reset()
trace_tipc_link_too_silent()
trace_tipc_link_retrans()
trace_tipc_link_bc_ack()
trace_tipc_link_conges()

And the traces for PROTOCOL messages at building and receiving:

trace_tipc_proto_build()
trace_tipc_proto_rcv()

Note:
a) The 'tipc_link_too_silent' event will only happen when the
'silent_intv_cnt' is about to reach the 'abort_limit' value (and the
event is enabled). The benefit for this kind of event is that we can
get an early indication about TIPC link loss issue due to timeout, then
can do some necessary actions for troubleshooting.

For example: To trigger the 'tipc_proto_rcv' when the 'too_silent'
event occurs:

echo 'enable_event:tipc:tipc_proto_rcv' > \
      events/tipc/tipc_link_too_silent/trigger

And disable it when TIPC link is reset:

echo 'disable_event:tipc:tipc_proto_rcv' > \
      events/tipc/tipc_link_reset/trigger

b) The 'tipc_link_retrans' or 'tipc_link_bc_ack' event is useful to
trace TIPC retransmission issues.

In addition, the commit adds the 'trace_tipc_list/link_dump()' at the
'retransmission failure' case. Then, if the issue occurs, the link
'transmq' along with the link data can be dumped for post-analysis.
These dump events should be enabled by default since it will only take
effect when the failure happens.

The same approach is also applied for the faulty case that the
validation of protocol message is failed.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

As for the sake of debugging/tracing, the commit enables tracepoints in
TIPC along with some general trace_events as shown below. It also
defines some 'tipc_*_dump()' functions that allow to dump TIPC object
data whenever needed, that is, for general debug purposes, ie. not just
for the trace_events.

The following trace_events are now available:

- trace_tipc_skb_dump(): allows to trace and dump TIPC msg & skb data,
  e.g. message type, user, droppable, skb truesize, cloned skb, etc.

- trace_tipc_list_dump(): allows to trace and dump any TIPC buffers or
  queues, e.g. TIPC link transmq, socket receive queue, etc.

- trace_tipc_sk_dump(): allows to trace and dump TIPC socket data, e.g.
  sk state, sk type, connection type, rmem_alloc, socket queues, etc.

- trace_tipc_link_dump(): allows to trace and dump TIPC link data, e.g.
  link state, silent_intv_cnt, gap, bc_gap, link queues, etc.

- trace_tipc_node_dump(): allows to trace and dump TIPC node data, e.g.
  node state, active links, capabilities, link entries, etc.

How to use:
Put the trace functions at any places where we want to dump TIPC data
or events.

Note:
a) The dump functions will generate raw data only, that is, to offload
the trace event's processing, it can require a tool or script to parse
the data but this should be simple.

b) The trace_tipc_*_dump() should be reserved for a failure cases only
(e.g. the retransmission failure case) or where we do not expect to
happen too often, then we can consider enabling these events by default
since they will almost not take any effects under normal conditions,
but once the rare condition or failure occurs, we get the dumped data
fully for post-analysis.

For other trace purposes, we can reuse these trace classes as template
but different events.

c) A trace_event is only effective when we enable it. To enable the
TIPC trace_events, echo 1 to 'enable' files in the events/tipc/
directory in the 'debugfs' file system. Normally, they are located at:

/sys/kernel/debug/tracing/events/tipc/

For example:

To enable the tipc_link_dump event:

echo 1 > /sys/kernel/debug/tracing/events/tipc/tipc_link_dump/enable

To enable all the TIPC trace_events:

echo 1 > /sys/kernel/debug/tracing/events/tipc/enable

To collect the trace data:

cat trace

or

cat trace_pipe > /trace.out &

To disable all the TIPC trace_events:

echo 0 > /sys/kernel/debug/tracing/events/tipc/enable

To clear the trace buffer:

echo > trace

d) Like the other trace_events, the feature like 'filter' or 'trigger'
is also usable for the tipc trace_events.
For more details, have a look at:

Documentation/trace/ftrace.txt

MAINTAINERS | add two new files 'trace.h' & 'trace.c' in tipc
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Westphal says:

====================
sk_buff: add extension infrastructure

TL;DR:
 - objdiff shows no change if CONFIG_XFRM=n && BR_NETFILTER=n
 - small size reduction when one or both options are set
 - no changes in ipsec performance

 Changes since v1:
 - Allocate entire extension space from a kmem_cache.
 - Avoid atomic_dec_and_test operation on skb_ext_put() for refcnt == 1 case.
   (similar to kfree_skbmem() fclone_ref use).

This adds an optional extension infrastructure, with ispec (xfrm) and
bridge netfilter as first users.

The third (future) user is Multipath TCP which is still out-of-tree.
MPTCP needs to map logical mptcp sequence numbers to the tcp sequence
numbers used by individual subflows.

This DSS mapping is read/written from tcp option space on receive and
written to tcp option space on transmitted tcp packets that are part of
and MPTCP connection.

Extending skb_shared_info or adding a private data field to skb fclones
doesn't work for incoming skb, so a different DSS propagation method would
be required for the receive side.

mptcp has same requirements as secpath/bridge netfilter:

1. extension memory is released when the sk_buff is free'd.
2. data is shared after cloning an skb (clone inherits extension)
3. adding extension to an skb will COW the extension buffer if needed.

Two new members are added to sk_buff:
1. 'active_extensions' byte (filling a hole), telling which extensions
   are available for this skb.
   This has two purposes.
   a) avoids the need to initialize the pointer.
   b) allows to "delete" an extension by clearing its bit
   value in ->active_extensions.

   While it would be possible to store the active_extensions byte
   in the extension struct instead of sk_buff, there is one problem
   with this:
    When an extension has to be disabled, we can always clear the
    bit in skb->active_extensions.  But in case it would be stored in the
    extension buffer itself, we might have to COW it first, if
    we are dealing with a cloned skb.  On kmalloc failure we would
    be unable to turn an extension off.
2. extension pointer, located at the end of the sk_buff.
   If the active_extensions byte is 0, the pointer is undefined,
   it is not initialized on skb allocation.

This adds extra code to skb clone and free paths (to deal with
refcount/free of extension area) but this replaces similar code that
manages skb->nf_bridge and skb->sp structs in the followup patches of
the series.

It is possible to add support for extensions that are not preseved on
clones/copies:

1. define a bitmask of all extensions that need copy/cow on clone
2. change __skb_ext_copy() to check
   ->active_extensions & SKB_EXT_PRESERVE_ON_CLONE
3. set clone->active_extensions to 0 if test is false.

This isn't done here because all extensions that get added here
need the copy/cow semantics.

Last patch converts skb->sp, secpath information gets stored as
new SKB_EXT_SEC_PATH, so the 'sp' pointer is removed from skbuff.

Extra code added to skb clone and free paths (to deal with refcount/free
of extension area) replaces the existing code that does the same for
skb->nf_bridge and skb->secpath.

I don't see any other in-tree users that could benefit from this
infrastructure, it doesn't make sense to add an extension just for the sake
of a single flag bit (like skb->nf_trace).

Adding a new extension is a good fit if all of the following are true:

1. Data is related to the skb/packet aggregate
2. Data should be freed when the skb is free'd
3. Data is not going to be relevant/needed in normal case (udp, tcp,
   forwarding workloads, ...)
4. There are no fancy action(s) needed on clone/free, such as callbacks
   into kernel modules.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove skb->sp and allocate secpath storage via extension
infrastructure.  This also reduces sk_buff by 8 bytes on x86_64.

Total size of allyesconfig kernel is reduced slightly, as there is
less inlined code (one conditional atomic op instead of two on
skb_clone).

No differences in throughput in following ipsec performance tests:
- transport mode with aes on 10GB link
- tunnel mode between two network namespaces with aes and null cipher
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

secpath_set is a wrapper for secpath_dup that will not perform
an allocation if the secpath attached to the skb has a reference count
of one, i.e., it doesn't need to be COW'ed.

Also, secpath_dup doesn't attach the secpath to the skb, it leaves
this to the caller.

Use secpath_set in places that immediately assign the return value to
skb.

This allows to remove skb->sp without touching these spots again.

secpath_dup can eventually be removed in followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

reduce noise when skb->sp is removed later in the series.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Will reduce noise when skb->sp is removed later in this series.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

... so this won't have to be changed when skb->sp goes away.

v2: no changes, preserve ack.
Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Will avoid touching this when sp pointer is removed from sk_buff struct.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use skb_sec_path and secpath_exists helpers where possible.
This reduces noise in followup patch that removes skb->sp pointer.

v2: no changes, preseve acks from v1.
Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_sec_path gains 'const' qualifier to avoid
xt_policy.c: 'skb_sec_path' discards 'const' qualifier from pointer target type

same reasoning as previous conversions: Won't need to touch these
spots anymore when skb->sp is removed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Future patch will remove skb->sp pointer.
To reduce noise in those patches, move existing helper to
sk_buff and use it in more places to ease skb->sp replacement later.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

It can only return 0 (success) or -ENOMEM.
Change return value to a pointer to secpath struct.

This avoids direct access to skb->sp:

err = secpath_set(skb);
if (!err) ..
skb->sp-> ...

Becomes:
sp = secpath_set(skb)
if (!sp) ..
sp-> ..

This reduces noise in followup patch which is going to remove skb->sp.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This converts the bridge netfilter (calling iptables hooks from bridge)
facility to use the extension infrastructure.

The bridge_nf specific hooks in skb clone and free paths are removed, they
have been replaced by the skb_ext hooks that do the same as the bridge nf
allocations hooks did.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds an optional extension infrastructure, with ispec (xfrm) and
bridge netfilter as first users.
objdiff shows no changes if kernel is built without xfrm and br_netfilter
support.

The third (planned future) user is Multipath TCP which is still
out-of-tree.
MPTCP needs to map logical mptcp sequence numbers to the tcp sequence
numbers used by individual subflows.

This DSS mapping is read/written from tcp option space on receive and
written to tcp option space on transmitted tcp packets that are part of
and MPTCP connection.

Extending skb_shared_info or adding a private data field to skb fclones
doesn't work for incoming skb, so a different DSS propagation method would
be required for the receive side.

mptcp has same requirements as secpath/bridge netfilter:

1. extension memory is released when the sk_buff is free'd.
2. data is shared after cloning an skb (clone inherits extension)
3. adding extension to an skb will COW the extension buffer if needed.

The "MPTCP upstreaming" effort adds SKB_EXT_MPTCP extension to store the
mapping for tx and rx processing.

Two new members are added to sk_buff:
1. 'active_extensions' byte (filling a hole), telling which extensions
   are available for this skb.
   This has two purposes.
   a) avoids the need to initialize the pointer.
   b) allows to "delete" an extension by clearing its bit
   value in ->active_extensions.

   While it would be possible to store the active_extensions byte
   in the extension struct instead of sk_buff, there is one problem
   with this:
    When an extension has to be disabled, we can always clear the
    bit in skb->active_extensions.  But in case it would be stored in the
    extension buffer itself, we might have to COW it first, if
    we are dealing with a cloned skb.  On kmalloc failure we would
    be unable to turn an extension off.

2. extension pointer, located at the end of the sk_buff.
   If the active_extensions byte is 0, the pointer is undefined,
   it is not initialized on skb allocation.

This adds extra code to skb clone and free paths (to deal with
refcount/free of extension area) but this replaces similar code that
manages skb->nf_bridge and skb->sp structs in the followup patches of
the series.

It is possible to add support for extensions that are not preseved on
clones/copies.

To do this, it would be needed to define a bitmask of all extensions that
need copy/cow semantics, and change __skb_ext_copy() to check
->active_extensions & SKB_EXT_PRESERVE_ON_CLONE, then just set
->active_extensions to 0 on the new clone.

This isn't done here because all extensions that get added here
need the copy/cow semantics.

v2:
Allocate entire extension space using kmem_cache.
Upside is that this allows better tracking of used memory,
downside is that we will allocate more space than strictly needed in
most cases (its unlikely that all extensions are active/needed at same
time for same skb).
The allocated memory (except the small extension header) is not cleared,
so no additonal overhead aside from memory usage.

Avoid atomic_dec_and_test operation on skb_ext_put()
by using similar trick as kfree_skbmem() does with fclone_ref:
If recount is 1, there is no concurrent user and we can free right away.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This pointer is going to be removed soon, so use the existing helpers in
more places to avoid noise when the removal happens.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ioana Ciornei says:

====================
dpaa2-eth: add QBMAN statistics

This patch set adds ethtool statistics for pending frames/bytes
in Rx/Tx conf FQs and number of buffers in pool.

The first patch adds support for the query APIs in the DPIO driver
while the latter actually exposes the statistics through ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add statistics for pending frames in Rx/Tx conf FQs and
number of buffers in pool. Available through ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add FQ (Frame Queue) and BP (Buffer Pool) query APIs that
users of QBMan can invoke to see the status of the queues
and pools that they are using.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Turn on Broadcast writes
- UNH 1.8.1 clear bias for UNH 1000BT distortion
- UNH 1.8.7 optimize pre-emphasis for 100BasTx UNH 100W fix
- Enable Token-ring during 'Coma Mode'
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2018-12-19

Here's the main bluetooth-next pull request for 4.21:

 - Multiple fixes & improvements for Broadcom-based controllers
 - New USB ID for an Intel controller
 - Support for new Broadcom controller variants
 - Use DEFINE_SHOW_ATTRIBUTE to simplify debugfs code
 - Eliminate confusing "last event is not cmd complete" warning message
 - Added vendor suspend/resume support for H:5 (3-Wire UART) controllers
 - Various other smaller improvements & fixes

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2018-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
This time we have too many changes to list, highlights:
 * virt_wifi - wireless control simulation on top of
   another network interface
 * hwsim configurability to test capabilities similar
   to real hardware
 * various mesh improvements
 * various radiotap vendor data fixes in mac80211
 * finally the nl_set_extack_cookie_u64() we talked
   about previously, used for
 * peer measurement APIs, right now only with FTM
   (flight time measurement) for location
 * made nl80211 radio/interface announcements more complete
 * various new HE (802.11ax) things:
   updates, TWT support, ...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In case a command which completes in Command Status was sent using the
hci_cmd_send-family of APIs there would be a misleading error in the
hci_get_cmd_complete function, since the code would be trying to fetch
the Command Complete parameters when there are none.

Avoid the misleading error and silently bail out from the function in
case the received event is a command status.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Broadcom controller on aries S5PV210 boards sends out a couple of
unknown packets after the firmware is loaded.  This will cause
logging of errors such as:
	Bluetooth: hci0: Frame reassembly failed (-84)

This is probably also the case with other boards, as there are related
Android userspace patches for custom ROMs such as
https://review.lineageos.org/#/c/LineageOS/android_system_bt/+/142721/
Since this appears to be intended behaviour, treated them as diagnostic
packets.

Note that this is another variant of commit 01d5e44a
("Bluetooth: hci_bcm: Handle empty packet after firmware loading")
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds the device ID for the BCM 4329 combo module used
in the Samsung Aries based phones (Galaxy S and it's variants).

```
[   11.508980] Bluetooth: hci0: BCM: chip id 41
[   11.518975] Bluetooth: hci0: BCM: features 0x04
[   11.550132] Bluetooth: hci0: BCM4329B1
[   11.557046] Bluetooth: hci0: BCM4329B1 (002.002.023) build 0000
[   13.737071] Bluetooth: hci0: BCM4329B1 (002.002.023) build 0744
```

Output from hciconfig

```
hci0:   Type: Primary  Bus: UART
        BD Address: 43:29:B1:55:00:00  ACL MTU: 1021:6  SCO MTU: 64:1
        UP RUNNING
        RX bytes:1675 acl:0 sco:0 events:145 errors:0
        TX bytes:20426 acl:0 sco:0 commands:146 errors:0
        Features: 0xbf 0xfe 0x8f 0xfe 0x9b 0xff 0x79 0x83
        Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
        Link policy: RSWITCH SNIFF
        Link mode: SLAVE ACCEPT
        Name: 'aries'
        Class: 0x000000
        Service Classes: Unspecified
        Device Class: Miscellaneous,
        HCI Version: 2.1 (0x4)  Revision: 0x2e8
        LMP Version: 2.1 (0x4)  Subversion: 0x4217
        Manufacturer: Broadcom Corporation (15)
```
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The radiotap vendor data might be placed after some other
radiotap elements, and thus when accessing it, need to access
the correct offset in the skb data. Fix the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Fix two bugs in ieee80211_get_vht_max_nss():
 * the spec says we should round down
   (reported by Nissim)
 * there's a double condition, the first one is wrong,
   supp_width == 0 / ext_nss_bw == 2 is valid in 80+80
   (found by smatch)

Fixes: b0aa75f0 ("ieee80211: add new VHT capability fields/parsing")
Reported-by: Nissim Bendanan <nissimx.bendanan@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Due to the alignment handling, it actually matters where in the code
we add the 4 bytes for the presence bitmap to the length; the first
field is the timestamp with 8 byte alignment so we need to add the
space for the extra vendor namespace presence bitmap *before* we do
any alignment for the fields.

Move the presence bitmap length accounting to the right place to fix
the alignment for the data properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Include the new USB product ID for Intel Bluetooth device 22260
family(CcPeak)

The /sys/kernel/debug/usb/devices portion for this device is:

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=8087 ProdID=0029 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

After phy_start() phylib takes care of all needed actions, including
aneg settings and checking link state. There's no need to set state
PHY_CHANGELINK in drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Microsemi has been bought by Microchip and Microchip is supporting those
switches.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NAME_DISTRIBUTOR messages are transmitted through unicast link on TIPC
2.0, by contrast, the messages are delivered through broadcast link on
TIPC 1.7. But at present, NAME_DISTRIBUTOR messages received by
broadcast link cannot be handled in tipc_rcv() until an unicast message
arrives, which may lead to a significant delay to update name table.

To avoid this delay, we will also deal with broadcast NAME_DISTRIBUTOR
message on broadcast receive path.
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

3c1bcc86 ("net: ethernet: Convert phydev advertize and supported
from u32 to link mode") left some unused code in phy_probe(), remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed:

====================
mlx5-uplink-rep-2018-12-15

Or Gerlitz says:

This series is essentially a cleanup to align with the rest of the NIC
switchdev drivers and make us
more robust and clear/n: currently the PF netdev serves as the mlx5
e-switch uplink netdev
representor when going into switchdev mode and back as plain NIC
netdev when going out.
This causes some irregularities and misc troubles.

Move to use dedicated uplink rep, as we have for the VF vports.

The uplink rep netdev does has sysfs link and supports the sriov vf
mac ndo, these two are in
use by libvirt and other orchestrators, It also has richer ethtool
support to allow controlling the
port link & mtu along with supporting dcb and plugging into the mlx5
lag logic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

function br_multicast_toggle now always return 0,
so the variable 'err' is unneeded.
Also cleanup dead branch in br_changelink.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1070:5: warning:
 variable 'op' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1342:5: warning:
 variable 'cmd_op' set but not used [-Wunused-but-set-variable]

'op' never used since introduction in commit 7cb03b23 ("qlcnic:
Support VF-PF communication channel commands.")
'cmd_op' not used since commit 6226204b ("qlcnic: Fix operation
type and command type.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On many devices the RTL8723BS device gets reset during suspend/resume,
causing it to lose its firmware and all state.

Testing has shown it drops back to communicating at 115200 bps and sends
sync-request packages, indicating it has been fully reset.

This commit fixes this by queueing a reprobe on resume.

This mirrors how USB RTL BT devices, which have the same problem, are
handled in the btusb driver, there we set the USB_QUIRK_RESET_RESUME for
all RTL devices, which also causes a reprobe on resume. The only difference
is that here we need to do the reprobe ourselves.

Since we are doing a full reprobe on resume now, we can also turn off the
device on suspend to save power while suspended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Add support for vendor specific suspend / resume callbacks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Trivial fix to clean up an indentation issue, remove spaces
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Trivial fix to clean up an indentation issue
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>