As indicated by note in iwl_ht_conf, some HT parameters are set on association
(e.g., channel width) and some vary over time (HT protection mode) and per
station (e.g., short GI support).  The global parameters should be set in
iwl_mac_config and the local/varying parameters in iwl_ht_conf.

This patch moves the channel width configuration from iwl_ht_conf to
iwl_mac_config, and defers further cleanup of the local/global conflation for a
later patch.

This fixes a bug in using HT40 channels in some modes.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a number of issues in iwl_rx_reply_rx and
iwl_pass_packet_to_mac80211.  These issues stem from the complexities of
managing two different types of packet commands for different hardware.

- Unify code handling rx_phy_res in SKB or cached to eliminate redundancy and
remove potential NULL pointer accesses
- Replace magic number with proper constant
- Optimize functions by moving early exit conditions before computation
- Comment code and improve some variable names
- Remove redundant computation in iwl_pass_packet_to_mac80211 by passing in the
correct, already-computed arguments.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some members of iwl_ht_info are unused, and one of
them is write-only, so we can remove these three:
max_amsdu_size, ampdu_factor and mpdu_density.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For devices using OTP memory, EEPROM image can start from
any one of the OTP blocks. If shadow RAM is disabled, we need to
traverse link list to find the last valid block, then start the EEPROM
image reading.

If OTP is not full, the valid block is the block _before_ the last block
on the link list; the last block on the link list is the empty block
ready for next OTP refresh/update.

If OTP is full, then the last block is the valid block to be used for
configure the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch cleans up the HT40 extension channels setup for EEPROM
band 6 and 7 to make it more readable.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Driver's first notification of a new station from mac80211 can be through rate
selection API.  This patch fixes a bug where, in this code path, the HT
capabilities of the new station were ignored.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The tx_chan_width entry is never used, supported_chan_width is used instead.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With EDCA and HCCA we have 16 potential tid values. This is accommodated by
mac80211, but iwlwifi only supports EDCA. With this implementation it is
thus possible for mac80211 to request a tid that will cause iwlwifi to read
outside array bounds. A similar problem exists if traffic is received in an
unsupported category.

We add error checking to catch these situations.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211_wext_siwfreq() should be exported with EXPORT_SYMBOL_GPL.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The HW TX power control init still needs work.
The SW init is complete according to the specs.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The V4 dummy transmission has two extra bools in its prototype,
so update all callers with the 2 bools.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To ensure a proper handling of CAN frames transported in skbuffs some checks
need to be performed at receive time.

As stated by Michael Olbrich and Luotao Fu BUG_ON() might be to restrictive.
This is right as we can just drop the non conform skbuff and the Kernel can
continue working.

This patch replaces the BUG_ON() with a WARN_ONCE() so that the system remains
healthy but we made the problem visible (once).
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Urs Thuermann <urs@isnogud.escape.de>
CC: Michael Olbrich <m.olbrich@pengutronix.de>
CC: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The whole restarting flag was introduced by Mike McCormack
and was a temporary duct tape patch around issues with transmits
inflight during restart. The problems it was covering are now
fixed and the code should have been reverted.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable netdev feature flag bit NETIF_F_FCOE_MTU for 82599 devices and enable
jumbo frame correspondingly when NETIF_F_FCOE_MTU is set.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add NETIF_F_FCOE_MTU to indicate that the NIC can support a secondary MTU for
converged traffic of LAN and Fiber Channel over Ethernet (FCoE). The MTU for
FCoE is 2158 = 14 (FCoE header) + 24 (FC header) + 2112 (FC max payload) +
4 (FC CRC) + 4 (FCoE trailer).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Updates netdev->vlan_features for NETIF_F_FCOE_CRC and NETIF_F_FSO, so that
FCoE CRC and GSO offloads will get used for FCoE over ixgbe based vlan
interface.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds fcoe offload related net_device_ops functions vlan_dev_fcoe_ddp_setup
and vlan_dev_fcoe_ddp_done, their implementation simply calls real eth device
net_device_ops for FCoE DDP setup and done operations.

Updates VLAN netdev field value for fcoe_ddp_xid from real eth device netdev.

Above changes are required for fcoe DDP offload working on a VLAN interface.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sky2 driver combines auto speed negotiation with automatic negotiation
of pause parameters; but the ethtool interface expects them to be
split. This patch allows autonegotiation to be used for speed, but
manually disable flow control.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Transmit completion can safely run lockless against transmit start.
In the normal case, completion is done from NAPI and only looks
at elements that are at the tail of the ring.  When doing shutdown
or reset, the transmiter should be completely block by NAPI disable
and blocking of transmit queue. 

Based on earlier work by Mike McCormack.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This unifies the places that bounce the device (suspend/resume
and restart). And makes the operations have the same semantics
as normal dev_open/dev_stop.

This also avoids setting the multicast addresses twice when
device is brought up.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The suspend and shutdown code plays with shared state. Use consistent
locking, for extra protection.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid any possible problems with accessing PHY registers on shutdown.
This is a purely theoretical issue and is not related to any of the
outstanding bug reports. Since receiver and transmitter are already
shutdown and phy interrupts for this device are already disabled,
there should already be enough protection. Suggested by Mike McCormack.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reseting the tx chain too soon results in invalid tx queue positions
being delivered in the status queue.  This also makes sure there's no
overlap between the cleanup done by sky2_tx_clean() and
sky2_tx_done().
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is pure refactoring.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Keep sky2->tx_prod consistent since int might be examined by
an softirq poll or restart.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also implement get/set BB mult, get/set TX gain, set RX gain,
disable/restore CRS, run/stop DDFS, RX IQ est and QDIV roundup
in the process.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a bug in ath9k_stop() where the HW
was not put into FULL_SLEEP state. Not doing so will
cause issues in suspend-resume and the HW will not respond
to chip resets.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a bug where the device was enabled
before restoring the PCI state.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

diversity_control and antenna_switch_swap are already
present in ath9k_ops_config. Remove duplicate occurrences
in ath_hw.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

PHY counters are available in all chipsets supported
by ath9k. Remove the check.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k supports the AR9002 family of chipsets. This includes
the AR9285 and the miniPCI AR9223 and AR9220 (which themselves
have AR9280+AR5133).

We now refer people to the wiki page as it seems this is not
as popular as we would have hoped.
Reported-by: JD <jd1008@gmail.com>
Cc: Dakota Lee <Dakota.Lee@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Sometimes drivers might have a good reason to override
the PS default, like iwlwifi right now where it affects
RX performance significantly at this point. This will
allow them to override the default, if desired, in a
way that users can still change it according to their
trade-off choices, not the driver's, like would happen
if the driver just disabled PS completely then.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If you trigger a scan request on an interface and then
take it down, or rmmod the module or unplug the device
the driver might "forget" to cancel the scan request.
That is a bug in the driver, but the current behaviour
is that we just hang endlessly waiting for the netdev
refcount to become 0 which it never will. To improve
robustness, check for this situation in cfg80211, warn
about it and clean up behind the driver. I don't just
clean up silently because it's likely that the driver
also has some internal state it has now leaked.

Additionally, this fixes a locking bug, clearing the
scan_req pointer should be done under the rdev lock.

Finally, we also need to _wait_ for the scan work and
not just abort it since it might be pending and wanting
to do a cleanup.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The length of the fixed portion of plink confirm frames is 4 bytes longer than
the other plink_action frames.  This path corrects an error in the length
adjustment done for these type of frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If a PREQ frame is received giving us a fresher DSN than what we have, record
the new dsn and mark it as valid.  This patch fixes a bug in the setting of the
MESH_PATH_DSN_VALID flag.

Also, minor fix to coding style on that file.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This matches ath9k, providing consistency when reading both drivers.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>