The code for setting the address of the internal TBI PHY was
convoluted enough without a maze of ifdefs. Clean it up a bit
so we allow the logic to fail down to -ENODEV at the end of
the if/else ladder, rather than using ifdefs to repeat the same
failure code over and over.

Also, remove the support for the auto-configuration. I'm not aware of
anyone using it, and it ends up using the bus mutex before it's been
initialized.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Djalal Harouni <tixxdz@opendz.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pdev->id is used in several places for different purpose.  All
these uses assume it's always the id of fec device which is >= 0.
However this is only true for non-DT case.  When DT plays, pdev->id
is always -1, which will break these pdev->id users.

Instead of fixing all these users one by one, this patch introduces
a new member 'dev_id' to 'struct fec_enet_private' for holding the
correct fec device id, and replaces all the existing uses of pdev->id
with this dev_id.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: Silence seq_scale() unused warning
  ipv4:correct description for tcp_max_syn_backlog
  pasemi_mac: Fix building as module
  netback: Fix alert message.
  r8169: fix Rx index race between FIFO overflow recovery and NAPI handler.
  r8169: Rx FIFO overflow fixes.
  ipv4: Fix peer validation on cached lookup.
  ipv4: make sure RTO_ONLINK is saved in routing cache
  iwlwifi: change the default behavior of watchdog timer
  iwlwifi: do not re-configure HT40 after associated
  iwlagn: fix HW crypto for TX-only keys
  Revert "mac80211: clear sta.drv_priv on reconfiguration"
  mac80211: fill rate filter for internal scan requests
  cfg80211: amend regulatory NULL dereference fix
  cfg80211: fix race on init and driver registration

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  ftrace: Fix hash record accounting bug
  perf: Fix parsing of __print_flags() in TP_printk()
  jump_label: jump_label_inc may return before the code is patched
  ftrace: Remove force undef config value left for testing
  tracing: Restore system filter behavior
  tracing: fix event_subsystem ref counting

On a CONFIG_NET=y build

net/core/secure_seq.c:22: warning: 'seq_scale' defined but not
used
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit c5ed63d6(tcp: fix three tcp sysctls tuning),
sysctl_max_syn_backlog is determined by tcp_hashinfo->ehash_mask,
and the minimal value is 128, and it will increase in proportion to the
memory of machine.
The original description for tcp_max_syn_backlog and sysctl_max_syn_backlog
are out of date.

Changelog:
V2: update description for sysctl_max_syn_backlog
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Reviewed-by: Shan Wei <shanwei88@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit ded19add ('pasemic_mac*: Move
the PA Semi driver') inadvertently split pasemi_mac into two separate
modules with unresolved symbols.  Change it back into a single module.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original message in netback_init was 'kthread_run() fails', which should be
'kthread_create() fails'.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
  toshiba_acpi: Fix machines that don't support HCI_SYSTEM_EVENT

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  intr_remapping: Fix section mismatch in ir_dev_scope_init()
  intel-iommu: Fix section mismatch in dmar_parse_rmrr_atsr_dev()
  x86, amd: Fix up numa_node information for AMD CPU family 15h model 0-0fh northbridge functions
  x86, AMD: Correct align_va_addr documentation
  x86/rtc, mrst: Don't register a platform RTC device for for Intel MID platforms
  x86/mrst: Battery fixes
  x86/paravirt: PTE updates in k(un)map_atomic need to be synchronous, regardless of lazy_mmu mode
  x86: Fix "Acer Aspire 1" reboot hang
  x86/mtrr: Resolve inconsistency with Intel processor manual
  x86: Document rdmsr_safe restrictions
  x86, microcode: Fix the failure path of microcode update driver init code
  Add TAINT_FIRMWARE_WORKAROUND on MTRR fixup
  x86/mpparse: Account for bus types other than ISA and PCI
  x86, mrst: Change the pmic_gpio device type to IPC
  mrst: Added some platform data for the SFI translations
  x86,mrst: Power control commands update
  x86/reboot: Blacklist Dell OptiPlex 990 known to require PCI reboot
  x86, UV: Fix UV2 hub part number
  x86: Add user_mode_vm check in stack_overflow_check

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix loss of notification with multi-event
  perf, x86: Force IBS LVT offset assignment for family 10h
  perf, x86: Disable PEBS on SandyBridge chips
  trace_events_filter: Use rcu_assign_pointer() when setting ftrace_event_call->filter
  perf session: Fix crash with invalid CPU list
  perf python: Fix undefined symbol problem
  perf/x86: Enable raw event access to Intel offcore events
  perf: Don't use -ENOSPC for out of PMU resources
  perf: Do not set task_ctx pointer in cpuctx if there are no events in the context
  perf/x86: Fix PEBS instruction unwind
  oprofile, x86: Fix crash when unloading module (nmi timer mode)
  oprofile: Fix crash when unloading module (hr timer mode)

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clockevents: Set noop handler in clockevents_exchange_device()
  tick-broadcast: Stop active broadcast device when replacing it
  clocksource: Fix bug with max_deferment margin calculation
  rtc: Fix some bugs that allowed accumulating time drift in suspend/resume
  rtc: Disable the alarm in the hardware

Merge branches 'core-urgent-for-linus' and 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  slab, lockdep: Fix silly bug

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Fix race condition when stopping the irq thread

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched, x86: Avoid unnecessary overflow in sched_clock
  sched: Fix buglet in return_cfs_rq_runtime()
  sched: Avoid SMT siblings in select_idle_sibling() if possible
  sched: Set the command name of the idle tasks in SMP kernels
  sched, rt: Provide means of disabling cross-cpu bandwidth sharing
  sched: Document wait_for_completion_*() return values
  sched_fair: Fix a typo in the comment describing update_sd_lb_stats
  sched: Add a comment to effective_load() since it's a pain

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] ap: Setup timer for sending messages after reset.
  [S390] cio: fix chsc_chp_vary
  [S390] cio: provide fake irb for transport mode IO
  [S390] cio: disallow driver io for known to be broken paths
  [S390] hibernate: directly trigger subchannel evaluation
  [S390] remove reset of system call restart on psw changes
  [S390] add missing .set function for NT_S390_LAST_BREAK regset
  [S390] fix page change underindication in pgste_update_all
  [S390] ptrace inferior call interactions with TIF_SYSCALL
  [S390] kdump: Replace is_kdump_kernel() with OLDMEM_BASE check

Since 92fc43b4, rtl8169_tx_timeout ends up
resetting Rx and Tx indexes and thus racing with the NAPI handler via
-> rtl8169_hw_reset
   -> rtl_hw_reset
      -> rtl8169_init_ring_indexes

What about returning to the original state ?

rtl_hw_reset is only used by rtl8169_hw_reset and rtl8169_init_one.

The latter does not need rtl8169_init_ring_indexes because the indexes
still contain their original values from the newly allocated network
device private data area (i.e. 0).

rtl8169_hw_reset is used by:
1. rtl8169_down
   Helper for rtl8169_close. rtl8169_open explicitely inits the indexes
   anyway.
2. rtl8169_pcierr_interrupt
   Indexes are set by rtl8169_reinit_task.
3. rtl8169_interrupt
   rtl8169_hw_reset is needed when the device goes down. See 1.
4. rtl_shutdown
   System shutdown handler. Indexes are irrelevant.
5. rtl8169_reset_task
   Indexes must be set before rtl_hw_start is called.
6. rtl8169_tx_timeout
   Indexes should not be set. This is the job of rtl8169_reset_task anyway.

The removal of rtl8169_hw_reset in rtl8169_tx_timeout and its move in
rtl8169_reset_task do not change the analysis.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Realtek has specified that the post 8168c gigabit chips and the post
8105e fast ethernet chips recover automatically from a Rx FIFO overflow.
The driver does not need to clear the RxFIFOOver bit of IntrStatus and
it should rather avoid messing it.

The implementation deserves some explanation:
1. events outside of the intr_event bit mask are now ignored. It enforces
   a no-processing policy for the events that either should not be there
   or should be ignored.

2. RxFIFOOver was already ignored in rtl_cfg_infos[RTL_CFG_1] for the
   whole 8168 line of chips with two exceptions:
   - RTL_GIGA_MAC_VER_22 since b5ba6d12
     ("use RxFIFO overflow workaround for 8168c chipset.").
     This one should now be correctly handled.
   - RTL_GIGA_MAC_VER_11 (8168b) which requires a different Rx FIFO
     overflow processing.

   Though it does not conform to Realtek suggestion above, the updated
   driver includes no change for RTL_GIGA_MAC_VER_12 and RTL_GIGA_MAC_VER_17.
   Both are 8168b. RTL_GIGA_MAC_VER_12 is common and a bit old so I'd rather
   wait for experimental evidence that the change suggested by Realtek really
   helps or does not hurt in unexpected ways.

   Removed case statements in rtl8169_interrupt are only 8168 relevant.

3. RxFIFOOver is masked for post 8105e 810x chips, namely the sole 8105e
   (RTL_GIGA_MAC_VER_30) itself.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I screwed up by compiling that driver for the machine rather
than the arch. Correcting this fixes the build error.

Cc: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If the set_ftrace_filter is cleared by writing just whitespace to
it, then the filter hash refcounts will be decremented but not
updated. This causes two bugs:

1) No functions will be enabled for tracing when they all should be

2) If the users clears the set_ftrace_filter twice, it will crash ftrace:

------------[ cut here ]------------
WARNING: at /home/rostedt/work/git/linux-trace.git/kernel/trace/ftrace.c:1384 __ftrace_hash_rec_update.part.27+0x157/0x1a7()
Modules linked in:
Pid: 2330, comm: bash Not tainted 3.1.0-test+ #32
Call Trace:
 [<ffffffff81051828>] warn_slowpath_common+0x83/0x9b
 [<ffffffff8105185a>] warn_slowpath_null+0x1a/0x1c
 [<ffffffff810ba362>] __ftrace_hash_rec_update.part.27+0x157/0x1a7
 [<ffffffff810ba6e8>] ? ftrace_regex_release+0xa7/0x10f
 [<ffffffff8111bdfe>] ? kfree+0xe5/0x115
 [<ffffffff810ba51e>] ftrace_hash_move+0x2e/0x151
 [<ffffffff810ba6fb>] ftrace_regex_release+0xba/0x10f
 [<ffffffff8112e49a>] fput+0xfd/0x1c2
 [<ffffffff8112b54c>] filp_close+0x6d/0x78
 [<ffffffff8113a92d>] sys_dup3+0x197/0x1c1
 [<ffffffff8113a9a6>] sys_dup2+0x4f/0x54
 [<ffffffff8150cac2>] system_call_fastpath+0x16/0x1b
---[ end trace 77a3a7ee73794a02 ]---

Link: http://lkml.kernel.org/r/20111101141420.GA4918@debianReported-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

A update is made to the sched:sched_switch event that adds some
logic to the first parameter of the __print_flags() that shows the
state of tasks. This change cause perf to fail parsing the flags.

A simple fix is needed to have the parser be able to process ops
within the argument.

Cc: stable@vger.kernel.org
Reported-by: Andrew Vagin <avagin@openvz.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

If cpu A calls jump_label_inc() just after atomic_add_return() is
called by cpu B, atomic_inc_not_zero() will return value greater then
zero and jump_label_inc() will return to a caller before jump_label_update()
finishes its job on cpu B.

Link: http://lkml.kernel.org/r/20111018175551.GH17571@redhat.com

Cc: stable@vger.kernel.org
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

A forced undef of a config value was used for testing and was
accidently left in during the final commit. This causes x86 to
run slower than needed while running function tracing as well
as causes the function graph selftest to fail when DYNMAIC_FTRACE
is not set. This is because the code in MCOUNT expects the ftrace
code to be processed with the config value set that happened to
be forced not set.

The forced config option was left in by:
    commit 6331c28c
    ftrace: Fix dynamic selftest failure on some archs

Link: http://lkml.kernel.org/r/20111102150255.GA6973@debian

Cc: stable@vger.kernel.org
Reported-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

Though not all events have field 'prev_pid', it was allowed to do this:

  # echo 'prev_pid == 100' > events/sched/filter

but commit 75b8e982 (tracing/filter: Swap
entire filter of events) broke it without any reason.

Link: http://lkml.kernel.org/r/4EAF46CF.8040408@cn.fujitsu.comSigned-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

Fix a bug introduced by e9dbfae5, which prevents event_subsystem from
ever being released.

Ref_count was added to keep track of subsystem users, not for counting
events.  Subsystem is created with ref_count = 1, so there is no need to
increment it for every event, we have nr_events for that.  Fix this by
touching ref_count only when we actually have a new user -
subsystem_open().

Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Link: http://lkml.kernel.org/r/1320052062-7846-1-git-send-email-idryomov@gmail.comSigned-off-by: Steven Rostedt <rostedt@goodmis.org>

If ipv4_valdiate_peer() fails during a cached entry lookup,
we'll NULL derer since the loop iterator assumes rth is not
NULL.

Letting this be handled as a failure is just bogus, so just make it
not fail.  If we have trouble getting a non-NULL neighbour for the
redirected gateway, just restore the original gateway and continue.

The very next use of this cached route will try again.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Satellite C670-10V generates notifications for hotkeys but does
not support HCI_SYSTEM_EVENT. As a result when a hotkey is pressed
it gets stuck in an infinite loop in toshiba_acpi_notify. To fix
this, detect whether or not HCI_SYSTEM_EVENT is supported up-front
and don't try to read system events if it isn't supported. In
addition, limit the number of retries when reading HCI_SYSTEM_EVENT
fails so that this loop cannot run unbounded.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

Fix:

 Section mismatch in reference from the function
 ir_dev_scope_init() to the function
 .init.text:dmar_dev_scope_init() The function
 ir_dev_scope_init() references the function __init dmar_dev_scope_init().
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Youquan Song <youquan.song@intel.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Link: http://lkml.kernel.org/r/20111026161507.GB10103@swordfishSigned-off-by: Ingo Molnar <mingo@elte.hu>

dmar_parse_rmrr_atsr_dev() calls rmrr_parse_dev() and
atsr_parse_dev() which are both marked as __init.

Section mismatch in reference from the function
dmar_parse_rmrr_atsr_dev() to the function
.init.text:dmar_parse_dev_scope() The function
dmar_parse_rmrr_atsr_dev() references the function __init
dmar_parse_dev_scope().

Section mismatch in reference from the function
dmar_parse_rmrr_atsr_dev() to the function
.init.text:dmar_parse_dev_scope() The function
dmar_parse_rmrr_atsr_dev() references the function __init
dmar_parse_dev_scope().
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: iommu@lists.linux-foundation.org
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Link: http://lkml.kernel.org/r/20111026154539.GA10103@swordfishSigned-off-by: Ingo Molnar <mingo@elte.hu>

I've received complaints that the numa_node attribute for family
15h model 00-0fh (e.g. Interlagos) northbridge functions shows
-1 instead of the proper node ID.

Correct this with attached quirks (similar to quirks for other
AMD CPU families used in multi-socket systems).
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Frank Arnold <frank.arnold@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/20111202072143.GA31916@alberich.amd.comSigned-off-by: Ingo Molnar <mingo@elte.hu>

Commit dfb09f9b ("x86, amd: Avoid cache aliasing penalties
on AMD family 15h") introduced a kernel command line parameter
called 'align_va_addr' which still refers to arguments used in
an earlier version of the patch and which got changed without
updating the documentation. Correct that omission.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Frank Arnold <frank.arnold@amd.com>
Link: http://lkml.kernel.org/r/1321873819-29541-1-git-send-email-bp@amd64.orgSigned-off-by: Ingo Molnar <mingo@elte.hu>

Intel MID x86 platforms have a memory mapped virtual RTC
instead.  No MID platform have the default ports (and
accessing them may do weird stuff).
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: feng.tang@intel.com
Cc: Feng Tang <feng.tang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

When DCDC input line over current detecting, PMIC will change
charging current automatically.  Logging event is enough.
Signed-off-by: Major Lee <major_lee@wistron.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
[fix build]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Fix an outstanding issue that has been reported since 2.6.37.
Under a heavy loaded machine processing "fork()" calls could
crash with:

BUG: unable to handle kernel paging request at f573fc8c
IP: [<c01abc54>] swap_count_continued+0x104/0x180
*pdpt = 000000002a3b9027 *pde = 0000000001bed067 *pte = 0000000000000000 Oops: 0000 [#1] SMP
Modules linked in:
Pid: 1638, comm: apache2 Not tainted 3.0.4-linode37 #1
EIP: 0061:[<c01abc54>] EFLAGS: 00210246 CPU: 3
EIP is at swap_count_continued+0x104/0x180
.. snip..
Call Trace:
 [<c01ac222>] ? __swap_duplicate+0xc2/0x160
 [<c01040f7>] ? pte_mfn_to_pfn+0x87/0xe0
 [<c01ac2e4>] ? swap_duplicate+0x14/0x40
 [<c01a0a6b>] ? copy_pte_range+0x45b/0x500
 [<c01a0ca5>] ? copy_page_range+0x195/0x200
 [<c01328c6>] ? dup_mmap+0x1c6/0x2c0
 [<c0132cf8>] ? dup_mm+0xa8/0x130
 [<c013376a>] ? copy_process+0x98a/0xb30
 [<c013395f>] ? do_fork+0x4f/0x280
 [<c01573b3>] ? getnstimeofday+0x43/0x100
 [<c010f770>] ? sys_clone+0x30/0x40
 [<c06c048d>] ? ptregs_clone+0x15/0x48
 [<c06bfb71>] ? syscall_call+0x7/0xb

The problem is that in copy_page_range() we turn lazy mode on,
and then in swap_entry_free() we call swap_count_continued()
which ends up in:

         map = kmap_atomic(page, KM_USER0) + offset;

and then later we touch *map.

Since we are running in batched mode (lazy) we don't actually
set up the PTE mappings and the kmap_atomic is not done
synchronously and ends up trying to dereference a page that has
not been set.

Looking at kmap_atomic_prot_pfn(), it uses
'arch_flush_lazy_mmu_mode' and doing the same in
kmap_atomic_prot() and __kunmap_atomic() makes the problem go
away.

Interestingly, commit b8bcfe99 ("x86/paravirt: remove lazy
mode in interrupts") removed part of this to fix an interrupt
issue - but it went to far and did not consider this scenario.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

Looks like on some Acer Aspire 1s with older bioses, reboot via bios
fails.  It works on my machine, (with BIOS version 0.3310) but
not on some others (BIOS version 0.3309).

There's a log of problems at:

  https://bbs.archlinux.org/viewtopic.php?id=124136

This patch adds a different callback to the reboot quirk table,
to allow rebooting via keybaord controller.
Reported-by: Uroš Vampl <mobile.leecher@gmail.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1323093233-9481-1-git-send-email-anarsoul@gmail.comSigned-off-by: Ingo Molnar <mingo@elte.hu>

Following is from Notes of section 11.5.3 of Intel processor
manual available at:

  http://www.intel.com/Assets/PDF/manual/325384.pdf

For the Pentium 4 and Intel Xeon processors, after the sequence of
steps given above has been executed, the cache lines containing the
code between the end of the WBINVD instruction and before the
MTRRS have actually been disabled may be retained in the cache
hierarchy. Here, to remove code from the cache completely, a
second WBINVD instruction must be executed after the MTRRs have
been disabled.

This patch provides resolution for that.

Ideally, I will like to make changes only for Pentium 4 and Xeon
processors. But, I am not finding easier way to do it.
And, extra wbinvd() instruction does not hurt much for other
processors.
Signed-off-by: Ajaykumar Hotchandani <ajaykumar.hotchandani@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Link: http://lkml.kernel.org/r/4EBD1CC5.3030008@oracle.comSigned-off-by: Ingo Molnar <mingo@elte.hu>

Merge branch 'tip/perf/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace into perf/urgent