- 21 Mar, 2011 40 commits
-
-
Igor M. Liplianin authored
MarkusF wrote: I accidently got a Terratec Cinergy S2 USB HD (instead of a Terratec Cinergy S2 PCI HD). I found in the windows driver, that the driver is for the usb ids: 0CCD:00A8 1F4D:3000 The dvb-s2 usb adapter has the id 0CCD-00A8. So I patches your driver and added the usb id, where the 1F4D:3000 is and it worked (after I downloaded the firmware dvb-fe-ds3000.fw). w_scan found the channels and vdr is working fine. Signed-off-by:
Igor M. Liplianin <liplianin@me.by> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Igor M. Liplianin authored
The card uses ds3000 demod from Montage. Signed-off-by:
-
Igor M. Liplianin authored
Before this patch we can use only one card type from list due to sharing one firmware name. Now it's fixed. Also driver tries to attach only appropriate demod for this cards. Signed-off-by:
-
Igor M. Liplianin authored
Signed-off-by:
-
Jesper Juhl authored
In drivers/media/dvb/ttusb-budget/dvb-ttusb-budget.c:ttusb_boot_dsp() we need to call release_firmware(fw) before returning or we'll leak - no matter if we succeed or fail. Signed-off-by:
Jesper Juhl <jj@chaosbits.net> Signed-off-by:
-
Mike Isely authored
Signed-off-by:
Mike Isely <isely@pobox.com> Signed-off-by:
-
Mike Isely authored
pvrusb2: Declare closed-caption setup for line 21 - this is needed for sliced VBI capture support. (However none of that works right now anyway.) Signed-off-by:
-
Servaas Vandenberghe authored
pvrusb2: The origin of the capability bounds rectangle may differ from (left=0,top=0) so the calculation should use absolute coordinates, here below, or use relative coordinates like cropl_val-cap->bounds.left and cropt_val-cap->bounds.top. Signed-off-by:
-
Mike Isely authored
Signed-off-by:
-
Mike Isely authored
Signed-off-by:
-
Mike Isely authored
pvrusb2: Recognize and handle mode change before dealing with changes related to the video standard. Even though the video standard should only matter when in analog mode, doing this way is technically cleaner in case there's other stuff that might depend on both. Signed-off-by:
-
Malcolm Priestley authored
This tuner PLL has missing initialisation settings resulting in haphazard tuning. The PLL LPF was set to just 22000 symbol rate. Basically, the module is a Sharp BS2F7HZ0194 (STV0299+IX2410) I have had problems implementing the PLL in a new driver and did not want to break the IX2410 out of the PLL. This applies to DW2102, DM1105, CX88 and OPERA1 drivers. Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by:
-
Stefan Richter authored
Since the drivers/ieee1394/ backend was removed from firedtv, its I/O no longer needs to be abstracted as exchangeable backend methods. Also, ieee1394 variants of module and device probe and removal are no longer there. Move module probe and removal into firedtv-fw.c where device probe and removal are implemented. Signed-off-by:
Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by:
-
Vasiliy Kulikov authored
Don't allow everybody to change video settings. Signed-off-by:
Vasiliy Kulikov <segoon@openwall.com> Acked-by:
Luca Risolia <luca.risolia@studio.unibo.it> Signed-off-by:
-
Dmitri Belimov authored
Changes: Add function tm6000_set_reg_mask for change some bits in regs. Very usefull, simplify some code with this function. Add control mute Add control volume Add control audio input MUX Add support radio Radio works well. TV works too Known bugs: The programm gnomeradio can't set freq for radio, it use old v4l API. Audio over USB works via arecord. The programm mplayer can set freq but no any audio mplayer -v -rawaudio rate=48000 radio://105.2/capture driver=v4l2:alsa:adevice=hw.1,0:amode=1:audiorate=48000:forceaudio:immediatemode=0 When start watch TV very shortly after radio the kernel crashed hardly. Didn't stop all USB URBs, need some time for stop. [mchehab@redhat.com: fix merge conflicts] Signed-off-by:Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com> Signed-off-by:
-
Holger Nelson authored
This patch adds support for Terratec Grabster AV 150/250 MX. For now it is only possible to use composite input as switching inputs does not work. [mchehab@redhat.com: Fix merge conflicts and simplify board entries] Signed-off-by:
Holger Nelson <hnelson@hnelson.de> Signed-off-by:
-
Dmitri Belimov authored
Add two new TV cards of Beholder. Signed-off-by:
-
Igor M. Liplianin authored
Speed up tuning, as firmware is not necessary to load every attempt to tune Signed-off-by:
-
Igor M. Liplianin authored
Decrease firmware loading time. Before it is ~4000 i2c calls, now it is ~256 i2c calls to load ds3000 firmware. Signed-off-by:
-
Igor M. Liplianin authored
TeVii s480 works fine with that on DVB-S2 channels Signed-off-by:
-
Igor M. Liplianin authored
Make some initializations in init, not in tune function Signed-off-by:
-
Lawrence Rust authored
This patch adds audio DMA capture and ALSA mixer elements for the line input jack of the Hauppauge Nova-S-plus DVB-S PCI card. The Nova-S-plus has a WM8775 ADC that is currently not detected. This patch enables this chip and exports volume, balance mute and ALC elements for ALSA mixer controls. [mchehab@redhat.com: Changed the patch to only talk with wm8775 if board info says so. Also, added platform_data support, to avoid changing the behaviour for other boards, and fixed CodingStyle] [awalls@md.metrocast.net: Changed patch to make the WM8775_GID defintion bridge driver private and let the bridge driver set the value of v4l2_subdev.grp_id.] -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.htmlSigned-off-by:
Andy Walls <awalls@md.metrocast.net>
-
Dmitri Belimov authored
Add one more radio input, usefull for tm6010 Add control output amplitude. Add set_config function for configure tuner when TV card hasn't dvb part. Signed-off-by:
-
Thomas Weber authored
Add linux/sched.h because of missing declaration of TASK_NORMAL. This patch fixes the following error: drivers/media/video/omap24xxcam.c: In function 'omap24xxcam_vbq_complete': drivers/media/video/omap24xxcam.c:415: error: 'TASK_NORMAL' undeclared (first use in this function) drivers/media/video/omap24xxcam.c:415: error: (Each undeclared identifier is reported only once drivers/media/video/omap24xxcam.c:415: error: for each function it appears in.) Signed-off-by:
Thomas Weber <weber@corscience.de> Signed-off-by:
-
Peter Huewe authored
This patch fixes the warning "Using plain integer as NULL pointer", generated by sparse, by replacing if (var == 0) with if (!var) after an allocation and all other offending 0s with NULL. KernelVersion: linus' tree-1f0324caSigned-off-by:
Peter Huewe <peterhuewe@gmx.de> Signed-off-by:
-
Hans Verkuil authored
The cxhdl->priv field was not set initially, only after capturing started. Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Acked-by:
-
Igor M. Liplianin authored
It takes too long time to scan due to low symbol rate PID's like PAT, PMT, CAT, NIT. For that matter we enabled permanently all PID's less 0x20 in hardware PID filter for NetUP Dual DVB-T/C CI RF card to combine rates. Signed-off-by:
Igor M. Liplianin <liplianin@netup.ru> Signed-off-by:
-
Igor M. Liplianin authored
Signed-off-by:
-
Igor M. Liplianin authored
This is needed for multifrontend support. NetUP Dual DVB-T/C CI RF card has frontends connected to port B & C Each frontend has two switchable cores - DVB-T & DVB-C Signed-off-by:
-
Igor M. Liplianin authored
There is two external I2C buses in cx23885 chip. Currently, analog tuners supported for second I2C bus only In NetUP Dual DVB-T/C CI RF card tuners connected to first bus So, in order to support analog tuners sitting on first bus we need modifications. Signed-off-by:
-
Igor M. Liplianin authored
The card based on cx23885 PCI-e brige. Altera FPGA for CI, multistandard demods stv0367 from STM for QAM & OFDM, Xcieve xc5000 tuners and additional cx25840 for second analog input. Signed-off-by:
-
Igor M. Liplianin authored
Signed-off-by:
-
Igor M. Liplianin authored
The STV0367 is a multi-standard demodulator which is capable of processing DVB-T as well as DVB-C signals. It is fully compliant with DVB-T and DVB-C recommendations for broadcast services. Signed-off-by:
-
Igor M. Liplianin authored
An Altera FPGA CI module for NetUP Dual DVB-T/C RF CI card. Signed-off-by:
-
Igor M. Liplianin authored
It uses STAPL files and programs Altera FPGA through JTAG. Interface to JTAG must be provided from main device module, for example through cx23885 GPIO. Signed-off-by:
-
Peter Huewe authored
This patch fixes the warning "Using plain integer as NULL pointer", generated by sparse, by replacing the offending 0s with NULL. Signed-off-by:
Devin Heitmueller <dheitmueller@hauppauge.com> Signed-off-by:
-
Andrew Chew authored
This soc_camera driver is for Omnivision's OV9740 sensor. This initial submission provides support for YUV422 output at 1280x720 (720p), which is the sensor's native resolution. 640x480 (VGA) is also supported, with cropping and scaling performed by the sensor's ISP. This driver is heavily based off of the existing OV9640 driver. Signed-off-by:
Andrew Chew <achew@nvidia.com> Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Guennadi Liakhovetski authored
Use the correct scales to calculate cropping offsets. Signed-off-by:
-
Guennadi Liakhovetski authored
Now that soc-camera supports videobuf API v1 and v2, camera-host drivers can be converted to videobuf2 individually. This patch converts the mx3_camera driver. Signed-off-by:
-
Guennadi Liakhovetski authored
Convert the sh_mobile_ceu_camera driver to the videobuf2 API. Signed-off-by:
-
