Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The latter are error-prone because the bank number is one less than one
would read in the documentation.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Eric Benard <eric@eukrea.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Note that the hardware schematics and documentations can be obtained
  here: http://www.bugcommunity.com/wiki/index.php/BUGbaseSigned-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This patch is to fix the warning below.

arch/arm/configs/mx51_defconfig:113:warning: symbol value 'm' invalid for LEDS_CLASS
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Most fix is for uart txd/cts. They don't need to select input.
And fix some other pads with wrong select input.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Enable cpufreq on Genesi efika platforms
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This patch declares regulators for the efikamx. Use it also to power off the
efikamx.
Unfortunately, on the efikamx to2 boards, this doesn't work but they allow to
power off by setting GPIO 4 13 to high level instead of powering off through
the mc13892.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Now that usb has been fixed, we can enable usb h1 on efikamx
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The Genesi EFIKA MX and EFIKA Smartbook are sharing a lot of things
so it makes sense to create a common file for both devices and a specific
file for each. No functionnal change except dropping uart 1 & 2.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX23 Reference Manaul starts auart index from 1 than 0.  Changing
the index to start from 0 requires corresponding changes on base
address, irq, and iomux definitions, and will probably confuse people
who reads codes and hardware documents together.

This patch introduced the field 'hwid' to distinguish the driver id
and controller id.  These two ids are different on mx23 while
identical on mx28.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX23 Reference Manual names auart irq differently from i.MX28.
This patch is to align the naming with mx28, so that some device
registration codes can be shared.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Do not include linux/device.h twice in drivers/tty/serial/mxs-auart.c .
Once is enough.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Fixes 2 small regressions of recent iomux changes:
 - current MX51_PAD_UART2_TXD__UART2_TXD declaration overwrites
   IOMUXC_UART2_IPP_UART_RXD_MUX_SELECT_INPUT register (0x09ec) and prevent
   UART2 Rx from working properly.
   (Tested on my custom i.MX51 board where UART2 is used as console)
 - current MX51_PAD_USBH1_DATA2__UART2_TXD declaration also has the same problem.
   (Not tested)
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The arguments to these callbacks were changed in

	e981a302 (ARM: mx3: irq_data conversion.)

but the comments were not adapted.

Cc: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mxc_board_init is too generic to be useful.  Additionally change some
mxc_timer to ${machine}_timer, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The mxc-ehci driver calls SoC specific phy initialization right after
calling board specific initialization. To offer greater flexibility for
boards to setup the phy and to get rid of some unnecessary flags in
platform data this patch lets the boards call the SoC specific phy
initialization and remove it from the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Currently we have a mxc_initialize_usb_hw which is called on every
i.MX SoC. This function dispatches the different SoC types, which
is quite ugly. This patch moves the SoC specific USB initialization
to their correspondive mach directories.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Conflicts:
	arch/arm/mach-mxs/clock-mx28.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the memory
mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This fixes:

	arch/arm/mach-mx3/mach-mx31_3ds.c:249: warning: 'mx31_3ds_host2_init' defined but not used
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ALSA: AACI: allow writes to MAINCR to take effect
  ARM: Update mach-types
  ARM: 6652/1: ep93xx: correct the end address of the AC97 memory resource
  ARM: mxs/imx28: remove now unused clock lookup "fec.0"
  ARM: mxs: fix clock base address missing
  ARM: mxs: acknowledge gpio irq
  ARM: mach-imx/mach-mx25_3ds: Fix section type
  ARM: imx: Add VPR200 and MX51_3DS entries to uncompress.h
  ARM i.MX23: use correct register for setting the rate
  ARM i.MX23/28: remove secondary field from struct clk. It's unused
  ARM i.MX28: use correct register for setting the rate
  ARM i.MX28: fix bit operation